Results for “Drying technology” — Page 5

NASA NTRSDate not supplied

Technology Assessment for Producing Propellant From Lunar Water

Introduction: The presence of water ice in permanently shadowed regions (PSRs) on the lunar surface may enable a sustained human presence on the Moon with minimal need for consumables. One of the most valuable uses of lunar water is to produce rocket propellant. A sustained human presence on the Moon will re-quire frequent launches from the lunar surface, and each launch will require tons of propellant. However, many other volatiles are likely to be present in the areas where lunar water is stable1. Producing propellant from lunar water in-situ will require the separation and purification of water before it can be electrolyzed into oxygen and hydrogen gas. The Resource Exploration and Science of OUR Cosmic Environment (RESOURCE) project, funded by the Solar System Exploration Research Virtual Institute (SSERVI) program, includes a task to demonstrate the end-to-end process of water extraction, capture, purification and electrolysis to produce pure/dry oxygen gas sourced from an icy regolith mixture. Water Purification: The requirements for water purity are driven by the type of water electrolyzer used. For example, the water electrolyzer currently used on the International Space Station is based on proton ex-change membrane (PEM) technology. PEM-based electrolyzers require water to be ultrapure and deionized (>10 MegaOhm-cm) so that electrical conductivity is limited to the membranes themselves, where electrical current is used to convert H2O into H2 and O2.. A practical first step toward purifying water that is sourced from a lunar PSR is to use freeze distillation to separate water from other volatiles2. A sub-micronic filter can also be used to ensure that a minimal amount of dust is present in any lunar water that is captured. The combination of freeze distillation and sub-micronic filtration will result in relatively pure water but would require a deionization step if being fed into a PEM electrolyzer. Water Electrolysis: An alternative to PEM electrolysis is to use a Solid Oxide Electrolyzer (SOE). This technology operates at a much higher operating temperature (~800oC) and has a limited pressure range but does not require water to be ultrapure and deionized. Another advantage of SOE technology is that it produces pure dry oxygen gas without the need of an additional drying step. PEM electrolyzers produce humid oxygen gas and the humidity must be removed prior to liquefaction. Assessment: In order to compare PEM and SOE technologies side-by-side, they must be compared at a system level that includes water purification and gas drying steps. Engineers at the Johnson Space Center up-dated and utilized a detailed In-Situ Resource Utilization (ISRU) system model to compare and select the best option for the RESOURCE project which will conclude with a laboratory demonstration of the process of producing pure/dry oxygen from an icy regolith mixture in 2025.

A.J. Paz↗

NASA NTRSDate not supplied

Technology Assessment for Producing Propellant From Lunar Water

Introduction: The presence of water ice in permanently shadowed regions (PSRs) on the lunar surface may enable a sustained human presence on the Moon with minimal need for consumables. One of the most valuable uses of lunar water is to produce rocket propellant. A sustained human presence on the Moon will re-quire frequent launches from the lunar surface, and each launch will require tons of propellant. However, many other volatiles are likely to be present in the areas where lunar water is stable1. Producing propellant from lunar water in-situ will require the separation and purification of water before it can be electrolyzed into oxygen and hydrogen gas. The Resource Exploration and Science of OUR Cosmic Environment (RESOURCE) project, funded by the Solar System Exploration Research Virtual Institute (SSERVI) program, includes a task to demonstrate the end-to-end process of water extraction, capture, purification and electrolysis to produce pure/dry oxygen gas sourced from an icy regolith mixture. Water Purification: The requirements for water purity are driven by the type of water electrolyzer used. For example, the water electrolyzer currently used on the International Space Station is based on proton ex-change membrane (PEM) technology. PEM-based electrolyzers require water to be ultrapure and deionized (>10 MegaOhm-cm) so that electrical conductivity is limited to the membranes themselves, where electrical current is used to convert H2O into H2 and O2.. A practical first step toward purifying water that is sourced from a lunar PSR is to use freeze distillation to separate water from other volatiles2. A sub-micronic filter can also be used to ensure that a minimal amount of dust is present in any lunar water that is captured. The combination of freeze distillation and sub-micronic filtration will result in relatively pure water but would require a deionization step if being fed into a PEM electrolyzer. Water Electrolysis: An alternative to PEM electrolysis is to use a Solid Oxide Electrolyzer (SOE). This technology operates at a much higher operating temperature (~800oC) and has a limited pressure range but does not require water to be ultrapure and deionized. Another advantage of SOE technology is that it produces pure dry oxygen gas without the need of an additional drying step. PEM electrolyzers produce humid oxygen gas and the humidity must be removed prior to liquefaction. Assessment: In order to compare PEM and SOE technologies side-by-side, they must be compared at a system level that includes water purification and gas drying steps. Engineers at the Johnson Space Center up-dated and utilized a detailed In-Situ Resource Utilization (ISRU) system model to compare and select the best option for the RESOURCE project which will conclude with a laboratory demonstration of the process of producing pure/dry oxygen from an icy regolith mixture in 2025.

ISRU↗

NASA NTRSDate not supplied

Automated Ply-By-Ply Lamination and in-Situ Consolidation of Dry Carbon Fiber Non-Crimp Fabrics for High-Rate Aircraft Manufacturing of Structural Aircraft Components

NASA’s Hi-Rate Composites Aircraft Manufacturing (HiCAM) program addresses market needs to advance structural aircraft composite manufacturing technologies to significantly increase production rates. Dry, non-crimp fabric (NCF) carbon materials infused with advanced resin systems offer a promising solution to these manufacturing demands. Northrop Grumman’s Automated Stiffener Forming (ASF) technology has been adapted for ply-by-ply, in-situ processing of NCF materials. The modular ASF process accommodates flexibility in the laminate stacking, while allowing for ply drops, ply additions, and yaw, pitch, and roll in the laminate geometry. To adapt the ASF process for NCF materials, heating technologies and roller compaction processes were designed and tested on representative structural aircraft part geometries. Key success criteria for the ASF process with NCF materials is forming quality and preform compaction. Trials were performed with multiple NCF materials: unidirectional up to quad-axial formats. The NCF constituents, veils, stitching, and binders, were evaluated with the ASF process. The material performance in the ASF process and the resulting preform quality are presented.

dry carbon fiber materials↗

NASA NTRSDate not supplied

Automated Ply-By-Ply Lamination and in-Situ Consolidation of Dry Carbon Fiber Non-Crimp Fabrics for High-Rate Aircraft Manufacturing of Structural Aircraft Components

NASA’s Hi-Rate Composites Aircraft Manufacturing (HiCAM) program addresses market needs to advance structural aircraft composite manufacturing technologies to significantly increase production rates. Dry, non-crimp fabric (NCF) carbon materials infused with advanced resin systems offer a promising solution to these manufacturing demands. Northrop Grumman’s Automated Stiffener Forming (ASF) technology has been adapted for ply-by-ply, in-situ processing of NCF materials. The modular ASF process accommodates flexibility in the laminate stacking, while allowing for ply drops, ply additions, and yaw, pitch, and roll in the laminate geometry. To adapt the ASF process for NCF materials, heating technologies and roller compaction processes were designed and tested on representative structural aircraft part geometries. Key success criteria for the ASF process with NCF materials is forming quality and preform compaction. Trials were performed with multiple NCF materials: unidirectional up to quad-axial formats. The NCF constituents, veils, stitching, and binders, were evaluated with the ASF process. The material performance in the ASF process and the resulting preform quality are presented.

dry carbon fiber materials↗

NASA NTRS1980

Space Coatings for Industry

Ball Aerospace developed entirely new space lubrication technologies. A new family of dry lubricants emerged from Apollo, specifically designed for long life in space, together with processes for applying them to spacecraft components in microscopically thin coatings. Lubricants worked successfully on seven Orbiting Solar Observatory flights over the span of a decade and attracted attention to other contractors which became Ball customers. The company has developed several hundred variations of the original OSO technology generally designed to improve the quality and useful life of a wide range of products or improve efficiency of the industrial processes by which such products are manufactured.

Source record↗

NASA NTRS1983

System technology analysis of aeroassisted orbital transfer vehicles - Moderate lift/drag

The utilization of procedures involving aerodynamic braking and/or aerodynamic maneuvering on return from higher altitude orbits to low-earth orbit makes it possible to realize significant performance benefits. The present study is concerned with a number of mission scenarios for Aeroassisted Orbital Transfer Vehicles (AOTV) and the impact of potential technology advances in the performance enhancement of the class of AOTV's having a hypersonic lift to drag ratio (L/D) of 0.75 to 1.5. It is found that the synergistic combination of a hypersonic L/D of 1.2, an advanced cryopropelled engine, and an LH2 drop tank (1-1/2 stage) leads to a single 65,000 pound shuttle, two-man geosynchronous mission with 2100 pounds of useful paylod. Additional payload enhancement is possible with AOTV dry weight reductions due to technology advances in the areas of vehicle structures and thermal protection systems and other subsystems.

Florence, D. E.↗

DOE OSTI2021

Energy-efficient sorption-based gas clothes dryer systems

Standard electric resistance and fuel-driven dehydration technologies exhibit a maximum coefficient of performance of well below 1 mainly due to enthalpy losses associated with the air leaving the dehydration system. To improve energy efficiency, condensing dryer systems condense the moisture captured from a product in a closed-loop air circulation cycle. Existing condensing dehydration systems including heat pump dryers, however, need to significantly cool the air to achieve dehumidification. The added cooling and subsequent heating to return the air to a desired drying temperature consume substantial energy and thus reduce drying performance. Here, an innovative sorption-based gas dehydration system is proposed to overcome barriers deteriorating energy efficiency in existing gas, electric, or heat pump dryer systems. Decoupling latent and sensible loads, the system employs a liquid-desiccant solution to directly capture air humidity, thereby allowing circulation of the air in a closed loop to achieve high drying energy efficiency. In other words, the system captures waste latent heat from the moisture produced during the dehydration process and reuses it to improve energy efficiency. This study focuses on a comprehensive quasi-steady-state thermodynamic modeling of the proposed sorption-based dehydration concept employed for a gas clothes dryer application to predict transient response and overall drying performance (i.e., time and energy metrics). The analysis indicates the proposed sorption-based gas clothes dryer system can deliver a specific moisture extraction rate of 1.71 kg of water per kWh (i.e., a combined energy factor of 3.167 kg (6.98 lbm) of dry cloth per kWh) with a drying time of 44 min. This is a 112% energy improvement compared with state-of-the-art gas clothes dryers exhibiting a combined energy factor of 1.50 kg (3.3 lbm) of dry cloth per kWh. The technology pursued here can potentially be employed as a platform for many fuel-driven equipment to take advantage of available waste thermal energy in the environment instead of simply burning a fuel.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2024

Modeling and Analysis of a Heat Pump Clothes Dryer with Thermal Energy Storage

Clothes drying is an energy-intensive process that causes significant electricity consumption and carbon emissions in the US. Approximately 83% of Households in the US own a tumble clothes dryer at home and 80% of dryers are electrical resistance dryers with low energy efficiency. Heat pump technology makes it possible for highly efficient and clean drying. Additionally, the ventless design of heat pump clothes dryers (HPCD) provides more installation flexibility. HPCD involves three primary mediums: wet clothes, a closed air loop, and a refrigerant circuit. The evaporator is used to dehumidify the wet air and the condenser is used to re-heat the dry air. One of the critical technological barriers to HPCD market penetration is its long drying time, primarily due to the relatively low discharging temperature and the slow response during the warm-up period. In this study, the thermal energy storage (TES) technology is adopted to address this challenge by providing pre-heating of air prior to the condenser to increase the operating temperature of the process air. The heat pump will charge the phase change material (PCM) in the TES device with heating energy during clothes washing and the PCM will discharge the stored heat to facilitate air heating during clothes drying. To analyze the optimal design and potential for energy saving and drying time reduction, a mathematical model of the HPCD system was developed. The HPCD is a highly dynamic system with a coupled heat and mass transfer and heat pumping cycle. This paper provides solutions to simulate the transient behavior of the system while maintaining low computational cost. The modeling result indicates reduced energy consumption and drying time by integrating TES with HPCD, as compared to electrical resistance dryers. The study can provide significant insights into improving building flexibility with TES and smart appliances.

Liu, Xiaoli↗

NASA NTRS2011

High Energy Failure Containment for Spacecraft

Objective: The objective of this paper will be to investigate advancements and any commonality between spacecraft debris containment and the improvements being made in ballistic protection. Scope: This paper will focus on cross application of protection devices and methods, and how they relate to protecting humans from failures in spacecraft. The potential gain is to reduce the risk associated with hardware failure, while decreasing the weight and size of energy containment methods currently being used by the government and commercial industry. Method of Approach: This paper will examine testing that has already been accomplished in regards to the failure of high energy rotating hardware and compare it to advancements in ballistic protection. Examples are: DOT research and testing of turbine containment as documented in DOT/FAA/AR-96/110, DOT/FAA/AR-97/82, DOT/FAA/AR-98/22. It will also look at work accomplished by companies such as ApNano and IBD Deisenroth in the development of nano ceramics and nanometric steels. Other forms of energy absorbent materials and composites will also be considered and discussed. New Advances in State of the Art: There have been numerous advances in technology in regards to high energy debris containment and in the similar field of ballistic protection. This paper will discuss methods such as using impregnated or dry Kevlar, ceramic, and nano-technology which have been successfully tested but are yet to be utilized in spacecraft. Reports on tungsten disulfide nanotubes claim that they are 4-5 times stronger than steel and reports vary about the magnitude increase over Kevlar, but it appears to be somewhere in the range of 2-6 times stronger. This technology could also have applications in the protection of pressure vessels, motor housings, and hydraulic component failures.

Pektas, Pete↗

NASA NTRS1986

Selecting hydrocarbon rocket propulsion technology

Past studies have shown that the dry weight of future earth-to-orbit vehicles can be reduced by the combined use of hydrogen and hydrocarbon propulsion compared to all-hydrogen propulsion. This paper shows that the use of certain hydrocarbon engines with hydrogen engines produces the lowest vehicle dry mass. These hydrocarbon engines use propane or RP-1 fuel, hydrogen cooling, and hydrogen-rich gas generators. Integration of the hydrogen and hydrocarbon nozzles is also beneficial.

Martin, J. A.↗

NASA NTRS2004

Bioinspired Engineering of Exploration Systems (BEES) - its Impact on Future Missions

This paper describes an overview of our "Bioinspired Engineering of Exploration Systems for Mars" ( "BEES for Mars") project. The BEES approach distills selected biologically inspired strategies utilizing motion cues/optic flow, bioinspired pattern recognition, biological visual and neural control systems, bioinspired sensing and communication techniques, and birds of prey inspired search and track algorithmic systems. Unique capabilities so enabled, provide potential solutions to future autonomous robotic space and planetary mission applications. With the first series of tests performed in September 2003, August 2004 and September 2004, we have demonstrated the BEES technologies at the El Mirage Dry Lakebed site in the Mojave Desert using Delta Wing experimental prototypes. We call these test flyers the "BEES flyer", since we are developing them as dedicated test platform for the newly developed bioinspired sensors, processors and algorithmic strategies. The Delta Wing offers a robust airframe that can sustain high G launches and offers ease of compact stowability and packaging along with scaling to small size and low ReynOld's number performance for a potential Mars deployment. Our approach to developing light weight, low power autonomous flight systems using concepts distilled from biology promises to enable new applications, of dual use to NASA and DoD needs. Small in size (0.5 -5 Kg) BEES Flyers are demonstrating capabilities for autonomous flight and sensor operability in Mars analog conditions. The BEES project team spans JPL, NASA Ames, Australian National University (ANU), Brigham Young University(BYU), DC Berkeiey, Analogic Computers Inc. and other institutions. The highlights from our recent flight demonstrations exhibiting new Mission enabling capabilities are described. Further, this paper describes two classes of potential new missions for Mars exploration: (1) the long range exploration missions, and (2) observation missions, for real time imaging of critical ephemeral phenomena, that can be enabled by use of BEES flyers. For example, such flyers can serve as a powerful black-box for critical descent and landing data and enablers for improved science missions complementing and supplementing the existing assets like landers and rovers by providing valuable exploration and quick extended low-altitude aerial coverage of the sites of interest by imaging them and distributing instruments to them. Imaging done by orbiters allows broad surface coverage at limited spatial resolution. Low altitude air-borne exploration of Mars offers a means for imaging large areas, perhaps up to several hundred kilometers, quickly and efficiently, providing a close-up birds-eye view of the planetary terrain and close-up approach to constrained difficult areas like canyons and craters. A novel approach to low-mass yet highly capable flyers is enabled by small aircraft equipped using sensors and processors and algorithms developed using BEES technology. This project is focused towards showing the direct impact of blending the best of artificial intelligence attributes and bioinspiration to create a leap beyond existing capability for our future Missions.

navigation↗

DOE OSTI2022

Chapter 8: Geothermal Energy

Geothermal resources are used at different temperatures for different applications, depending on the resource temperature; applications include power generation, direct heating and cooling, mineral recovery, and energy storage. This chapter focuses on the most prominent applications of geothermal energy today: power generation and direct heating and cooling, specifically, dry steam, flash, and binary technologies. Other topics explored include: direct use of geothermal resources, thermodynamic cycle applications, and the multiple steps and multiple technologies involved in capturing all minerals of interest in a cost-effective way.

cooling↗

DOE OSTI2025

Shear Assisted Processing and Extrusion of Magnesium Alloy Machining Chips

The Pacific Northwest National Laboratory (PNNL) utilized Shear Assisted Processing and Extrusion (ShAPE) to convert magnesium alloy machining chips directly into wrought material. PNNL fabricated 0.25” and 0.50” round rod from cold compacted briquettes pressed from dry-machined chips by Loukus Technologies. The alloy composition is proprietary and protected by a Materials Transfer Agreement (MTA) between PNNL and Loukus. Extrusions were fabricated using the ShAPE 2.0 machine, tooling, and process. PNNL is evaluating tensile properties per ASTM E8 and microstructure for grain size, texture, and porosity using Scanning Electron Microscopy (SEM) and Electron Backscatter Diffraction (EBSD). Tensile properties and microstructure results were not available at the time of writing this document. Extruded rods have also been sent to Loukus for evaluation.

36 MATERIALS SCIENCE↗

NASA NTRS1976

Nozzle selection for optimized single-stage shuttles

A computerized preliminary design procedure has been used to determine rocket-engine bell-nozzle configurations which achieve either minimum gross mass or minimum dry mass on an advanced technology winged single-stage-to-orbit launch vehicle. This procedure evaluates the trade offs between the optimized ascent flight trajectory performance and the flight vehicle sizing driven by the engine mass and propellant requirements. Numerous mission, flight, and vehicle related requirements and constraints are satisfied in this process. Propulsion system configurations which incorporate dual-position nozzles are evaluated and compared to configurations using all fixed nozzles.

Eldred, C. H.↗

DOE OSTI2024

High performance heat exchangers for next generation hybrid cooler (CRADA NFE-19-07891 Final Report)

The evaporative cooling process has been successfully deployed in multiple energy conversion processes such as power generation, process cooling, heating, ventilation & cooling (HVAC), and commercial and industrial refrigeration. The heat exchanger is a very common yet extremely critical component of such systems. The device is important since the performance of the overall cooling system heavily relies on the thermal-hydraulic efficiency of the heat exchanger. The possible wet operation as evaporative cooling heat exchanger complicates the issue. Indeed, based on the hybrid nature of operation (fully dry, partially wet, fully wet) the efficiency can vary significantly and can cause performance variation for the whole system. Understanding the importance of the issue, Oak Ridge National Laboratory (Contractor) and Baltimore Aircoil Company (Participant) propose an activity focused on the analysis of the existing heat exchanger technology used in air and evaporative cooling processes and design, development and demonstration of a novel heat exchanger design based on porous materials. The potential candidates include metallic wire meshes and metal foams carefully designed for the proposed application. Prior research has indicated that these materials have great potential for deployment in thermal systems, particularly heat sinks and heat exchangers. It is expected that the successful completion of the project will lead to novel heat exchanger technology for hybrid systems (capable of dry and wet operation) by exploring newly emerging materials and their potential for heat transfer application. The overall goal is to develop a next generation heat exchanger technology which can be deployed in evaporative cooling systems. The impact of the such development is significant since, it will not only make the overall system highly efficient but will also, reduce the total refrigerant charge in the heat exchanger, a critical aspect for the deployment of refrigerants with lower Global Warming Potential (GWP).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2024

High performance heat exchangers for next generation hybrid cooler (CRADA Final Report)

The evaporative cooling process has been successfully deployed in multiple energy conversion processes such as power generation, process cooling, heating, ventilation & cooling (HVAC), and commercial and industrial refrigeration. The heat exchanger is a very common yet extremely critical component of such systems. The device is important since the performance of the overall cooling system heavily relies on the thermal-hydraulic efficiency of the heat exchanger. The possible wet operation as evaporative cooling heat exchanger complicates the issue. Indeed, based on the hybrid nature of operation (fully dry, partially wet, fully wet) the efficiency can vary significantly and can cause performance variation for the whole system. Understanding the importance of the issue, Oak Ridge National Laboratory (Contractor) and Baltimore Aircoil Company (Participant) propose an activity focused on the analysis of the existing heat exchanger technology used in air and evaporative cooling processes and design, development and demonstration of a novel heat exchanger design based on porous materials. The potential candidates include metallic wire meshes and metal foams carefully designed for the proposed application. Prior research has indicated that these materials have great potential for deployment in thermal systems, particularly heat sinks and heat exchangers. It is expected that the successful completion of the project will lead to novel heat exchanger technology for hybrid systems (capable of dry and wet operation) by exploring newly emerging materials and their potential for heat transfer application. The overall goal is to develop a next generation heat exchanger technology which can be deployed in evaporative cooling systems. The impact of the such development is significant since, it will not only make the overall system highly efficient but will also, reduce the total refrigerant charge in the heat exchanger, a critical aspect for the deployment of refrigerants with lower Global Warming Potential (GWP).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS1965

Dry film lubricants

The Space Age has necessitated accelerated development of many technologies which have direct application to commercial, earthbound hardware. One striking example is dry film lubrication. The stimulus for the development of dry film lubricants was provided by the unsatisfactory condition created when commercial liquid lubricants were exposed to the multiple environs of space. In the search for a satisfactory solution to lubrication in space, dry films were investigated. The dry film lubrication concept has proven most desirable for space, and a natural fallout is the potential shown by such films for consumer item application. On the acceptance that the coefficient of friction of dry films is not equivalent to that of a liquid lubricant under ideal conditions, this paper discusses how the ideal condition for liquid lubrication is rarely achieved in practical applications. Comparisons are made between the performance of dry film and liquid lubricants as a function of temperature, environmental pressure, and life. Furthermore, consideration is given to the comparative costs of liquid versus dry film lubricants to show the practicality and desirability of dry film lubrication to consumer items. Although no data on the performance of consumer items lubricated with dry films are presented, the comparisons clearly establish the potential of dry film lubricants in a competitive consumer market.

SOLID LUBRICANT↗

NASA NTRS1982

Advanced rocket propulsion technology assessment for future space transportation

Single-stage and two-stage launch vehicles were evaluated for various levels of propulsion technology and payloads. The evaluation included tradeoffs between ascent flight performance and vehicle sizing that were driven by engine mass, specific impulse, and propellant requirements. Numerous mission, flight, and vehicle-related requirements and constraints were satisfied in the design process. The results showed that advanced technology had a large effect on reducing both single- and two-stage vehicle size. High-pressure hydrocarbon-fueled engines that were burned in parallel with two-position nozzle hydrogen-fueled engines reduced dry mass by 23% for the two-stage vehicle and 28% for the single-stage vehicle as compared to an all-hydrogen-fueled system. The dual-expander engine reduced single-stage vehicle dry mass by 41%. Using advanced technology, the single-stage vehicle became comparable in size and sensitivity to that of the two-stage vehicle for small payloads.

Wilhite, A. W.↗