Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Deltas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Delta K measurements with synthetic aperture radar data

Delta K measurements are obtained from the interference of two electromagnetic waves of different frequencies. Constructive interference occurs when 2pi phase differences between the two frequencies correspond to a surface wavelength. Previous Delta K measurements have used two discrete frequencies for this purpose. Range pulses and Doppler signatures of a synthetic aperture radar system were filtered to obtain a sequence of Delta K values. Those Delta K values which correspond to the wavelengths of known surfaces show maximum constructive interference. SAR data can therefore be used for Delta K measurements, indicating the possibility of selective Delta K filtering during data gathering.

Larson, R. W.↗

Photodissociation of metastable O2(a 1 Delta g): Implications for stratospheric O3

The potential energy curves of Saxon and Liu (1977) are used to calculate nuclear radial wave functions for O2 in the a 1 Delta g and C 3 Delta u states. Franck-Condon factors are evaluated for both bound-bound and bound-free transitions. Observational values for the radiative lifetimes of discrete vibrational levels of the C 3 Delta u state are used to place constraints on the cross section for photodissociaation of a 1 Delta g. It is argued that the cross section for the dissociation of O2(a 1 Delta g) through the C 3 Delta u state is smaller by four orders of magnitude than values required by Frederick and Cicerone (1985) to resolve the apparent discrepancy between computed and measured concentrations for O3 in the upper atmosphere.

Dalgarno, A.↗

Study of lee-side flows over conically cambered delta wings at supersonic speeds, part 1

An experimental investigation was performed in which surface pressure data, flow visualization data, and force and moment data were obtained on four conical delta wing models which differed in leading-edge camber only. Wing leading-edge camber was achieved through a deflection of the outboard 30% of the local wind semispan of a reference 75 degrees swept flat delta wing. The four wing models have leading-edge deflection angles delta sub F of 0, 5, 10, and 15 degrees measured streamwise. Data for the wings with delta sub F = 10 and 15 degrees showed that hinge-line separation dominated the lee-side wing loading and prohibited the develpment of leading-edge separation on the deflected portion of wing leading edge. However, data for the wing with delta sub F = 5 degrees, a vortex was positioned on the deflected leading edge with reattachment at the hinge line. Flow visualization results were presented which detail the influence of Mach number, angle of attack, and camber on the lee-side flow characteristics of conically cambered delta wings. Analysis of photgraphic data identified the existence of 12 distinctive lee-side flow types. In general, the aerodynamic force and moment data correlated well with the pressure and flow visualization data.

Wood, Richard M.↗

Study of lee-side flows over conically cambered Delta wings at supersonic speeds, part 2

An experimental investigation was performed in which surface pressure data, flow visualization data, and force and moment data were obtained on four conical delta wing models which differed in leading edge camber only. Wing leading edge camber was achieved through a deflection of the outboard 30% of the local wing semispan of a reference 75 deg swept flat delta wing. The four wing models have leading edge deflection angles delta sub F of 0, 5, 10, and 15 deg measured streamwise. Data for the wings with delta sub F = 10 and 15 deg showed that hinge line separation dominated the lee-side wing loading and prohibited the development of leading edge separation on the deflected portion of wing leading edge. However, data for the wing with delta sub F = 5 deg showed that at an angle of attack of 5 deg, a vortex was positioned on the deflected leading edge with reattachment at the hinge line. Flow visualization results were presented which detail the influence of Mach number, angle of attack, and camber on the lee-side flow characteristics of conically cambered delta wings. Analysis of photographic data identified the existence of 12 distinctive lee-side flow types.

Wood, Richard M.↗

Accelerated crack growth rate at low Delta K in a single crystal superalloy

The low Delta K crack growth behavior of a single crystal of the PWA 1480 nickel-based superalloy was investigated. The crystal was tested in the near (100) orientation with the side faces being in the near (001) orientation. Although in the higher Delta K region the fatigue crack growth (FCG) behavior is rather normal, at Delta K of about 8 MPa sq rt m, a transition occurs where the FCG rate appears to be independent of Delta K. This region is found to continue until Delta K of about 2.5 MPa sq rt m, where the FCG rate again decreases with decreasing Delta K.

Telesman, Jack↗

Studies of iron impurities in YxPr1-xBa2Cu3O7-delta

Pr is the only rare earth which, when substituted for Y in YBa2Cu3O7, significantly alters the superconducting transition temperature T(sub c) without changing the crystal structure. For YxPr1-xBa2Cu3O7-delta with delta approx. equal to 0, T(sub c) is reduced rapidly as x is increased, reaching zero for x about 0.5. For x above 0.5 the compound is antiferromagnetic with a Neel temperature that increases with increasing x, rising to above room temperature for x near 1. A similar behavior is observed when the oxygen deficit delta is increased from zero to 1 with x=0. For the case of Pr substitution, the drop in T(sub c) is believed due to magnetic interactions. For the case of varying delta with x=0, the drop can be attributed to a combination of magnetic interactions, band filling, and changes in crystal structure. To study these effects, the Mossbauer effect of 57 Fe atoms substituted for the Cu atoms has been observed as a function of delta, x, and temperature. The observed spectra are all well described by a two quadrupole-split pairs, a central singlet, and a six-line magnetic hyperfine field pattern. For several Pr compositions both delta and temperature were varied, and the results support the hypothesis that a magnetic interaction exists between the Fe in the Cu lattice and the substitutional Pr atoms.

Swartzendruber, L. J.↗

Conical Euler analysis and active roll suppression for unsteady vortical flows about rolling delta wings

A conical Euler code was developed to study unsteady vortex-dominated flows about rolling, highly swept delta wings undergoing either forced motions or free-to-roll motions that include active roll suppression. The flow solver of the code involves a multistage, Runge-Kutta time-stepping scheme that uses a cell-centered, finite-volume, spatial discretization of the Euler equations on an unstructured grid of triangles. The code allows for the additional analysis of the free to-roll case by simultaneously integrating in time the rigid-body equation of motion with the governing flow equations. Results are presented for a delta wing with a 75 deg swept, sharp leading edge at a free-stream Mach number of 1.2 and at 10 deg, 20 deg, and 30 deg angle of attack alpha. At the lower angles of attack (10 and 20 deg), forced-harmonic analyses indicate that the rolling-moment coefficients provide a positive damping, which is verified by free-to-roll calculations. In contrast, at the higher angle of attack (30 deg), a forced-harmonic analysis indicates that the rolling-moment coefficient provides negative damping at the small roll amplitudes. A free-to-roll calculation for this case produces an initially divergent response, but as the amplitude of motion grows with time, the response transitions to a wing-rock type of limit cycle oscillation, which is characteristic of highly swept delta wings. This limit cycle oscillation may be actively suppressed through the use of a rate-feedback control law and antisymmetrically deflected leading-edge flaps. Descriptions of the conical Euler flow solver and the free-to roll analysis are included in this report. Results are presented that demonstrate how the systematic analysis of the forced response of the delta wing can be used to predict the stable, neutrally stable, and unstable free response of the delta wing. These results also give insight into the flow physics associated with unsteady vortical flows about delta wings undergoing forced motions and free-to-roll motions, including the active suppression of the wing-rock type phenomenon. The conical Euler methodology developed is directly extend able to three-dimensional calculations.

Lee-Rausch, Elizabeth M.↗

Electronic structure and the van Hove singularity scenario in high-T(sub c)H(g)Ba2CuO(4+delta) superconductors

The electronic structure and the hole concentrations in the high Tc superconductor HgBa2CuO(4+delta) (delta = O, 1) has been investigated by employing a first principles full potential self-consistent LMTO method with the local density functional theory. The scalar relativistic effects have been considered. The hole concentrations of the Cu-d and O-p(x,y) orbitals are seen to be larger for the HgBaCuO5 system than those of the HgBaCuO4 solid. However, the van Hove singularity (vHs) induced Cu-d and O-p peak which is seen to lie comparatively away and above the Fermi level in the delta = 1 system shifts towards the Fermi level in the delta = 0 system. Thus, the superconducting behavior appears to originate from the occurrence of the vHs peak at the Fermi level. The Fermi surface nesting area in the delta = 0 compound is seen to be larger than in the delta = 1 compound. The calculation reveals that the increase in pressure on the crystal enhances the hole concentrations but without showing any optimum value, On the other hand, the vHs peak approaches to-wards the Fermi level with pressure and crosses the Fermi surface near V/Vo approximately equals 0.625 (V and Vo are the crystal volumes at high and normal pressures, respectively). Our calculated value of the bulk modulus equal to 0.626 Mbar predicts the occurrence of this crossover at about 24 GPa which is in complete agreement with the experimental value. At this pressure the compound has maximum nesting area and self-doped behavior.

Agrawal, Bal K.↗

Delta L: An Apparatus for Measuring Macromolecular Crystal Growth Rates in Microgravity

In order to determine how macromolecule crystal quality improvement in microgravity is related to crystal growth characteristics, is was necessary to develop new hardware that could measure the crystal growth rates of a population of crystals growing under the same solution conditions. As crystal growth rate is defined as the change or delta in a defined dimension or length (L) of a crystal over time, the hardware was named Delta L. Delta L consists of fluids, optics, and data acquisition, sub-assemblies. Temperature control is provided for the crystal growth chamber. Delta L will be used in connection with the Glovebox Integrated Microgravity Isolation Technology (g-LIMIT) inside the Microgravity Science Glovebox (MSG), onboard the International Space Station (ISS). Delta L prototype hardware has been assembled. This paper will describe an overview of the design of Delta L and present preliminary crystal growth rate data.

Judge, Russell A.↗

Characterizing Land Surface Change and Levee Stability in the Sacramento-San Joaquin Delta Using UAVSAR Radar Imagery

The Sacramento-San Joaquin Delta is one of the primary water sources for the state of California and represents a complex geographical area comprised of tidal marshland, levee rimmed islands that are used primarily for agriculture, and urban encroachment. Land subsidence has dropped many of the Delta islands 3 to >7 meters below mean sea level and requires nearly 1700 km of levees to maintain the integrity of the islands and flow of water through the Delta. The current average subsidence rates for each island varies, with 1.23 cm/yr on Sherman Island and 2.2 cm/yr for Bacon Island, as determined by ground-based instruments located at isolated points in the Delta. The Delta's status as the most critical water resource for the state, an endangered ecosystem, and an area continuously threatened with levee breakage from hydrostatic pressure and the danger of earthquakes on several major faults in the San Francisco area make it a focus of monitoring efforts by both the state and national government. This activity is now almost entirely done by ground-based efforts, but the benefits of using remote sensing for wide scale spatial coverage and frequent temporal coverage is obvious. The UAVSAR airborne polarimetric and differential interferometric L-band synthetic aperture radar system has been used to collected monthly images of the Sacramento-San Joaquin Delta and much of the adjacent Suisun Marsh since July 2009 to characterize levee stability, image spatially varied subsidence, and assess how well the UAVSAR performs in an area with widespread agriculture production.

geographical area↗

Adaptive Management Using Remote Sensing and Ecosystem Modeling in Response to Climate Variability and Invasive Aquatic Plants for the California Sacramento-San Joaquin Delta Water Resource

The California Sacramento-San Joaquin River Delta is the hub for California's water supply and supports important ecosystem services, agriculture, and communities in Northern to Southern California. Expansion of invasive aquatic plants in the Delta coupled with impacts of changing climate and long-term drought is detrimental to the San Francisco Bay/California Delta complex. NASA Ames Research Center and the USDA-ARS partnered with the State of California to develop science-based, adaptive-management strategies for invasive aquatic plant in the Sacramento-San Joaquin Delta. Specific mapping tools developed utilizing satellite and airborne platforms provide regular assessments of population dynamics on a landscape scale and support both strategic planning and operational decision making for resource managers. San Joaquin and Sacramento River watersheds water quality input to the Delta is modeled using the Soil-Water Assessment Tool (SWAT) and a modified SWAT tool has been customized to account for unique landscape and management of agricultural water supply and drainage within the Delta. Environmental response models for growth of invasive aquatic weeds are being parameterized and coupled with spatial distribution/biomass density mapping and water quality to study ecosystem response to climate and aquatic plant management practices. On the water validation and operational utilization of these tools by management agencies and how they are improving decision making, management effectiveness and efficiency will be discussed. The project combines science, operations, and economics related to integrated management scenarios for aquatic weeds to help land and water resource managers make science-informed decisions regarding management and outcomes.

Adaptive↗

New Treatment of Strongly Anisotropic Scattering Phase Functions: The Delta-M+ Method

The treatment of strongly anisotropic scattering phase functions is still a challenge for accurate radiance computations. The new delta-M+ method resolves this problem by introducing a reliable, fast, accurate, and easy-to-use Legendre expansion of the scattering phase function with modified moments. Delta-M+ is an upgrade of the widely used delta-M method that truncates the forward scattering peak with a Dirac delta function, where the ‘‘+’’ symbol indicates that it essentially matches moments beyond the first M terms. Compared with the original delta-M method, delta-M+ has the same computational efficiency, but for radiance computations, the accuracy and stability have been increased dramatically.

Lin, Zhenyi↗

Delta-Doped High Purity Silicon UV-NIR CCDs with High QE and Low Dark Current

Delta doping process was developed on p-channel CCDs for MIDEX-Orion and JDEM/SNAP and was applied to large format (2k x4k) CCDs. Delta doping is applied to fully-fabricated CCDs (complete with Al metallization). High QE and low dark current is demonstrated with delta doped p-channel CCDs. In-house AR coating is demonstrated. Advantages include: Delta doping enables high QE and stability across the entire spectral range attainable with silicon. Delta doping is a low temperature process and is compatible with fully-fabricated detector arrays. Same base device for Orion two channels. High radiation tolerance and no thinning requirements of high purity p-channel. CCDs are additional advantages.

Orion↗

Delta Modulation

An optimum adaptive delta modulator-demodulator configuration is derived. This device utilizes two past samples to obtain a step size which minimizes the mean square error for a Markov Gaussian source. The optimum system is compared using computer simulations with the linear delta modulator and an enhanced Abate delta modulator. In addition the performance is compared to the rate distortion bound for a Markov source. It is shown that the optimum delta modulator is neither quantization nor slope-overload limited. The results show that the output signal-to-noise ratio is independent of the input signal power and is subject only to the limitations of the hardware employed. In addition, voice was recorded using these systems. The demodulated voice indicates negligible degradation is caused by the optimum system and by the enhanced Abate system while the linear delta modulator suffers significant degradation at a sampling frequency of 56 kilobits/sec.

Schilling, D. L.↗

Computing approximate random Delta v magnitude probability densities

This paper describes the development and use of an algorithm to compute approximate statistics of the magnitude of a single random trajectory correction maneuver (TCM) Delta v vector. The TCM Delta v vector is modeled as a three component Cartesian vector each of whose components is a random variable having a normal (Gaussian) distribution with zero mean and possibly unequal standard deviations. The algorithm uses these standard deviations as input to produce approximations to (1) the mean and standard deviation of the magnitude of Delta v, (2) points of the probability density function of the magnitude of Delta v, and (3) points of the cumulative and inverse cumulative distribution functions of Delta v. The approximates are based on Monte Carlo techniques developed in a previous paper by the author and extended here. The algorithm described is expected to be useful in both pre-flight planning and in-flight analysis of maneuver propellant requirements for space missions.

Chadwick, C.↗

Designing Delta-DOR acquisition strategies to determine highly elliptical earth orbits

Delta-DOR acquisition strategies are designed for use in determining highly elliptical earth orbits. The requirements for a possible flight demonstration are evaluated for the Charged Composition Explorer spacecraft of the Active Magnetospheric Particle Tracer Explorers. The best-performing strategy uses data spanning the view periods of two orthogonal baselines near the same orbit periapse. The rapidly changing viewing geometry yields both angular position and velocity information, but each observation may require a different reference quasar. The Delta-DOR data noise is highly dependent on acquisition geometry, varying several orders of magnitude across the baseline view periods. Strategies are selected to minimize the measurement noise predicted by a theoretical model. Although the CCE transponder is limited by S-band and a small bandwidth, the addition of Delta-DOR to coherent Doppler and range improves the one-sigma apogee position accuracy by more than an order of magnitude. Additional Delta-DOR accuracy improvements possible using dual-frequency (S/X) calibration, increased spanned bandwidth, and water-vapor radiometry are presented for comparison. With these benefits, the residual Delta-DOR data noise is primarily due to quasar position uncertainties.

Frauenholz, R. B.↗

Applications of classical and zero-total-pressure-loss sets of Euler equations to delta wings

Classical and zero-total pressure-loss sets of Euler equations were applied to sharp- and round-edge delta wings. The origin of the total pressure was explained in the classical set. For sharp-edged delta wings, all sets of Euler equations produce the same separated flow solutions. For round-edged delta wings and for coarse grids, the solution depends on the level of dissipation, the accuracy of the surface boundary condition, and the type of Euler equations set. For round-edged delta wings and for fine grids, attached flow solutions are obtained. Also presented were three dimensional flow solutions and asymmetric flow solutions including unsteady flow for sharp-edged delta wings. Euler equations should be restricted to sharp-edged wings for real flow solutions. For roung-edged wings, Navier-Stokes equations must be used.

Kandil, Osama A.↗

Computational study of wind-tunnel wall effects on flow field around delta wings

This paper addresses wind-tunnel wall effects on delta-wing flow fields using the Free Vortex Sheet (FVS) theory in support of planned subsonic wind-tunnel tests. The configurations include several sizes of a 65-deg delta wing in the NASA Langley Research Center Low-Turbulence Pressure Tunnel (LTPT), and an aspect ratio 1 delta wing in the Delft University low-speed tunnel. Standard upflow correction methodology is extended to account for angle-of-attack and nonplanar effects. Blockage and streamline curvature corrections are not applied in the present investigation. Resulting corrections to the 65-deg delta flow field were good for model-to-tunnel span ratios up to 0.5 and angles of attack up to 30-deg, both for linear attached flow and nonlinear vortex flow. For the aspect ratio 1 delta wing, corrections to the vortex flow field for the effect of the averaged upflow angle were satisfactory but streamline curvature effects were larger.

Frink, Neal T.↗