SEARCH · Engineering Papers

Results for “Critical experiment design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS2004

Radio science receiver support of the Mars Exploration Rover Landings

The low power levels of the communication signals during the Entry Descent and Landing (EDL) sequences of the Mars rovers prevented the transmission of telemetry at X-band signal to inform the mission operations center of the health and progress of the spacecraft. As an altemative, a series of tones were sent to indicate basic spacecraft conditions and execution of critical events. An open-loop receiver designed for Radio Science experiments was used to acquire the signal during this time. The receiver recorded over a 100 Khz bandwidth to identify the presence of the carrier and tones. The data were fed in real-time to a processing unit which detected the carrier and the frequency separation of the tones from the carrier, in order to determine which event has occurred. Up to 256 different tones were possible. During the actual events, all tones were identified, and the carrier was tracked down to the surface, and for the second rover, through the bouncing which followed, and finally, while stopped on the surface, found the carrier and tones which indicated the spacecraft was alive. In order to identify the tones, the ground receivers had to be able to respond to the bevy of events occurring in the relatively short timespan of EDL.

Deep Space Network (DSN)↗

NASA NTRS2005

Narrow Angle Wide Spectral Range Radiometer Design FEANICS/REEFS Radiometer Design Report

A critical measurement for the Radiative Enhancement Effects on Flame Spread (REEFS) microgravity combustion experiment is the net radiative flux emitted from the gases and from the solid fuel bed. These quantities are measured using a set of narrow angle, wide spectral range radiometers. The radiometers are required to have an angular field of view of 1.2 degrees and measure over the spectral range of 0.6 to 30 microns, which presents a challenging design effort. This report details the design of this radiometer system including field of view, radiometer response, radiometric calculations, temperature effects, error sources, baffling and amplifiers. This report presents some radiometer specific data but does not present any REEFS experiment data.

Camperchioli, William↗

NASA NTRS1990

Supercritical microgravity droplet vaporization

Supercritical droplet vaporization is an important issue in many combustion systems, such as liquid fueled rockets and compression-ignition (diesel) engines. In order to study the details of droplet behavior at these conditions, an experiment was designed to provide a gas phase environment which is above the critical pressure and critical temperature of a single liquid droplet. In general, the droplet begins as a cold droplet in the hot, high pressure environment. In order to eliminate disruptions to the droplet by convective motion in the gas, forced and natural convection gas motion are required to be small. Implementation of this requirement for forced convection is straightforward, while reduction of natural convection is achieved by reduction in the g-level for the experiment. The resulting experiment consists of a rig which can stably position a droplet without restraint in a high-pressure, high temperature gas field in microgravity. The microgravity field is currently achieved by dropping the device in the NASA Lewis 2.2 second drop tower. The performance of the experimental device and results to date are presented.

Hartfield, J.↗

NASA NTRS2020

Buckling of Thin-Walled Circular Cylinders

Recent industry and NASA experience with the development of launch vehicle structures have indicated a need for updated monographs for the design of buckling-critical structures that account for state-of-the-art structural configurations, material systems, and computational tools. This monograph provides an update to NASA SP-8007 (circa 1965, and 1968) and was prepared under the cognizance of the NASA Engineering and Safety Center (NESC). It summarizes all significant knowledge and experience accumulated from the NESC Shell Buckling Knockdown Factor (SBKF) Assessment (NESC Assessment #: 07-010-E) to date for use in the design of buckling-critical thin-walled circular cylinders. The format and terminology used in this monograph is similar to previous versions of NASA SP-8007 for ease of understanding and implementation. In addition, as with the design recommendations contained in the previous versions of NASA SP-8007, this monograph is to be regarded as a guideline to design and not as a NASA requirement, unless specified in formal program requirements. Furthermore, it is expected that the guidelines presented in this monograph will be updated as appropriate. Designers are advised to stay abreast of updates in the state-of-the-art and corresponding design criteria.

Buckling↗

NASA NTRS1972

Outer planet Grand Tour missions photometry/polarimetry experiment critical components study

Work performed during this effort was limited to two primary areas of technical concern: optical design optimization, and sensor selection. An optical system concept was established, and various system components were evaluated through experimental test sequences. Photodetectors were investigated for the applicability in meeting OPGT requirements as constrained by the photometry/polarimetry team directives. The most promising (gallium arsenide PMT) was further experimentally tested to ascertain its behavior with respect to anticipated environmental conditions. Results of testing and summary of the preceding tradeoff study effort are presented.

Pellicori, S. F.↗

NASA NTRS2016

Preliminary Results from the AFRL-NASA W/V-Band Terrestrial Link Experiment in Albuquerque, NM

Atmospheric propagation models and the measurements that train them are critical to the design of efficient and effective space-ground links. As communication systems advance to higher frequencies in search of higher data rates and open spectrum, a lack of data at these frequencies necessitates new measurements to properly develop, validate, and refine the models used for link budgeting and system design. In collaboration with the Air Force Research Laboratory (AFRL), NASA Glenn Research Center has deployed the WV-band Terrestrial Link Experiment (WTLE) in Albuquerque, NM to conduct a measurement campaign at 72 and 84 GHz, among the first atmospheric propagation measurements at these frequencies. WTLE has been operational since October 1, 2015, and the system design shall be herein discussed alongside preliminary results and performance.

propagation↗

NASA NTRS2002

Impact Crater Size and Evolution: Expectations for Deep Impact

Deep Impact will involve a unique cratering experiment designed to probe below the surface of a comet. Laboratory experiments provide critical data for crater scaling and evolution of the ejecta curtain. Additional information is contained in the original extended abstract.

Schultz, P. H.↗

NASA NTRSDate not supplied

Development and Implementation of a Small Satellite Systems Engineering Webinar Series: A Collaboration Between United Nations Office for Outer Space Affairs and National Aeronautics and Space Administration

The United Nations Office for Outer Space Affairs (UNOOSA) in collaboration with the National Aeronautics and Space Administration (NASA) established a webinar series on NASA systems engineering standards and practices for the purpose of sharing knowledge in this area through UNOOSA’s “Access to Space for All” which provides free and accessible educational content. Through NASA’s Small Spacecraft Systems Virtual Institute (S3VI), the four-part series was designed to cover basic systems engineering and project management skills that are fundamental for planning, developing, and implementing an experiment or a space project, and that serve as critical knowledge for those engaged in space activities, whether as a designer, builder, or manager of space infrastructure and services. This first series of webinars was convened over the course of November 2023 through February 2024. The webinar series was segmented into four one and a half hour webinars which covered topics related to the Fundamentals of Systems Engineering, Requirements and Systems Engineering, System Assembly, Integration and Test, and Spacecraft Handling, as well as an Introduction to the Small Spacecraft Systems Virtual Institute (S3VI). The agendas for the first three webinars focused on addressing a number of questions relevant to a particular topic. Examples of these questions include: What is systems engineering and what does a systems engineer do? Why does NASA use systems engineering? How do you define requirements for a small spacecraft mission? Why are requirements important to space missions? How are trade studies used to determine parts selection and why are they important? The final webinar of the first series provided interactive discussions and demonstrations of the S3VI tools; shared information on additional webinar opportunities offered by the S3VI; and reviewed databases curated by the S3VI that include the Small Satellite Reliability Initiative (SSRI) Knowledge Base Tool, Mission Design Tools, Small Spacecraft Information Search, and the State-of-the-Art (SoA) Small Spacecraft Report. Future webinar series will be conducted with topics are to be determined. The presenter will discuss details related to the first webinar series and future plans for additional series.

systems engineering↗

NASA NTRSDate not supplied

Development and Implementation of A Small Satellite Systems Engineering Webinar Series: A Collaboration Between the United Nations Office for Outer Space Affairs and the National Aeronautics and Space Administration

Systems Engineering↗

NASA NTRS1973

Experimental detailed power distribution in a fast spectrum thermionic reactor fuel element at the core/BeO reflector interface region

A zero-power critical assembly was designed, constructed, and operated for the prupose of conducting a series of benchmark experiments dealing with the physics characteristics of a UN-fueled, Li-7-cooled, Mo-reflected, drum-controlled compact fast reactor for use with a space-power conversion system. The critical assembly was modified to simulate a fast spectrum advanced thermionics reactor by: (1) using BeO as a reflector in place of some of the existing molybdenum, (2) substituting Nb-1Zr tubing for some of the existing Ta tubing, and (3) inserting four full-scale mockups of thermionic type fuel elements near the core and BeO reflector boundary. These mockups were surrounded with a buffer zone having the equivalent thermionic core composition. In addition to measuring the critical mass of this thermionic configuration, a detailed power distribution in one of the thermionic element stages in the mixed spectrum region was measured. A power peak to average ratio of two was observed for this fuel stage at the midplane of the core and adjacent to the reflector. Also, the power on the outer surface adjacent to the BeO was slightly more than a factor of two larger than the power on the inside surface of a 5.08 cm (2.0 in.) high annular fuel segment with a 2.52 cm (0.993 in. ) o.d. and a 1.86 cm (0.731 in.) i.d.

Klann, P. G.↗

NASA NTRS2016

Experiences with Extra-Vehicular Activities in Response to Critical ISS Contingencies

The maturation of the International Space Station (ISS) design from the proposed Space Station Freedom to today's current implementation resulted in external hardware redundancy vulnerabilities in the final design. Failure to compensate for or respond to these vulnerabilities could put the ISS in a posture to where it could no longer function as a habitable space station. In the first years of ISS assembly, these responses were to largely be addressed by the continued resupply and Extra-Vehicular Activity (EVA) capabilities of the Space Shuttle. Even prior to the decision to retire the Space Shuttle, it was realized that ISS needed to have its own capability to be able to rapidly repair or replace external hardware without needing to wait for the next cargo resupply mission. As documented in a previous publicatoin5, in 2006 development was started to baseline Extra- Vehicular Activity (EVA, or spacewalk) procedures to replace hardware components whose failure would expose some of the ISS vulnerabilities should a second failure occur. This development work laid the groundwork for the onboard crews and the ground operations and engineering teams to be ready to replace any of this failed hardware. In 2010, this development work was put to the test when one of these pieces of hardware failed. This paper will provide a brief summary of the planning and processes established in the original Contingency EVA development phase. It will then review how those plans and processes were implemented in 2010, highlighting what went well as well as where there were deficiencies between theory and reality. This paper will show that the original approach and analyses, though sound, were not as thorough as they should have been in the realm of planning for next worse failures, for documenting Programmatic approval of key assumptions, and not pursuing sufficient engineering analysis prior to the failure of the hardware. The paper will further highlight the changes made to the Contingency EVA preparation team structure, approach, goals, and the resources allocated to its work after the 2010 events. Finally, the authors will overview the implementation of these updates in addressing failures onboard the ISS in 2012, 2013, and 2014. The successful use of the updated approaches, and the application of the approaches to other spacewalks, will demonstrate the effectiveness of this additional work and make a case for putting significant time and resources into pre-failure planning and analysis for critical hardware items on human-tended spacecraft.

Van Cise, E. A.↗

NASA NTRS2016

Experiences with Extra-Vehicular Activities in Response to Critical ISS Contingencies

The maturation of the International Space Station (ISS) design from the proposed Space Station Freedom to today's current implementation resulted in external hardware redundancy vulnerabilities in the final design. Failure to compensate for or respond to these vulnerabilities could put the ISS in a posture where it could no longer function as a habitable space station. In the first years of ISS assembly, these responses were to largely be addressed by the continued resupply and Extra-Vehicular Activity (EVA) capabilities of the Space Shuttle. Even prior to the decision to retire the Space Shuttle, it was realized that ISS needed to have its own capability to be able to rapidly repair or replace external hardware without needing to wait for the next cargo resupply mission. As documented in a previous publication, in 2006 development was started to baseline Extra-Vehicular Activity (EVA, or spacewalk) procedures to replace hardware components whose failure would expose some of the ISS vulnerabilities should a second failure occur. This development work laid the groundwork for the onboard crews and the ground operations and engineering teams to be ready to replace any of this failed hardware. In 2010, this development work was put to the test when one of these pieces of hardware failed. This paper will provide a brief summary of the planning and processes established in the original Contingency EVA development phase. It will then review how those plans and processes were implemented in 2010, highlighting what went well as well as where there were deficiencies between theory and reality. This paper will show that the original approach and analyses, though sound, were not as thorough as they should have been in the realm of planning for next worse failures, for documenting Programmatic approval of key assumptions, and not pursuing sufficient engineering analysis prior to the failure of the hardware. The paper will further highlight the changes made to the Contingency EVA preparation team structure, approach, goals, and the resources allocated to its work after the 2010 events. Finally, the authors will overview the implementation of these updates in addressing failures onboard the ISS in 2012, 2013, and 2014. The successful use of the updated approaches, and the application of the approaches to other spacewalks, will demonstrate the effectiveness of this additional work and make a case for putting significant time and resources into pre-failure planning and analysis for critical hardware items on human-tended spacecraft.

Van Cise, E. A.↗

NASA NTRS1996

Application of Optimization Techniques to Design of Unconventional Rocket Nozzle Configurations

Several current rocket engine concepts such as the bell-annular tri-propellant engine, and the linear aerospike being proposed for the X-33 require unconventional three dimensional rocket nozzles which must conform to rectangular or sector shaped envelopes to meet integration constraints. These types of nozzles exist outside the current experience database, therefore, the application of efficient design methods for these propulsion concepts is critical to the success of launch vehicle programs. The objective of this work is to optimize several different nozzle configurations, including two- and three-dimensional geometries. Methodology includes coupling computational fluid dynamic (CFD) analysis to genetic algorithms and Taguchi methods as well as implementation of a streamline tracing technique. Results of applications are shown for several geometeries including: three dimensional thruster nozzles with round or super elliptic throats and rectangualar exits, two- and three-dimensional thrusters installed within a bell nozzle, and three dimensional thrusters with round throats and sector shaped exits. Due to the novel designs considered for this study, there is little experience which can be used to guide the effort and limit the design space. With a nearly infinite parameter space to explore, simple parametric design studies cannot possibly search the entire design space within the time frame required to impact the design cycle. For this reason, robust and efficient optimization methods are required to explore and exploit the design space to achieve high performance engine designs. Five case studies which examine the application of various techniques in the engineering environment are presented in this paper.

Follett, W.↗

NASA NTRS1985

A Fundamental Study of Smoldering with Emphasis on Experimental Design for Zero-G

The objective of this section of the microgravity project is to identify key sets of low-gravity experiments which would critically compliment a larger set of more easily performed normal-gravity experiments to explain the phenomena found in smoldering combustion. It is planned to follow through on the conceptual design of these experiments by participating in the future in the fabrication of the refined apparatus and in the data collection and interpretation. Low-gravity experiments are appropriate for smoldering combustion because of the complexity of smoldering which requires every means possible to discriminate among the many chemical and physical mechanisms active in most smoldering combustion scenarios. Efforts will be primarily analytical, attempting to identify appropriate approximations and dominant dimensionless groups based on existing data and state-of-the-art combustion modelling. Transient stability questions such as ignition, extinction and the choices among charring, tarring, or flaming modes will be included.

Pagni, P. J.↗

NASA NTRS2016

Flight Experiment Verification of Shuttle Boundary Layer Transition Prediction Tool

Boundary layer transition at hypersonic conditions is critical to the design of future high-speed aircraft and spacecraft. Accurate methods to predict transition would directly impact the aerothermodynamic environments used to size a hypersonic vehicle's thermal protection system. A transition prediction tool, based on wind tunnel derived discrete roughness correlations, was developed and implemented for the Space Shuttle return-to-flight program. This tool was also used to design a boundary layer transition flight experiment in order to assess correlation uncertainties, particularly with regard to high Mach-number transition and tunnel-to-flight scaling. A review is provided of the results obtained from the flight experiment in order to evaluate the transition prediction tool implemented for the Shuttle program.

Berry, Scott A.↗

NASA NTRS1971

Experimental physics characteristics of a heavy-metal-reflected fast-spectrum critical assembly

A zero-power critical assembly was designed, constructed, and operated for the purpose of conducting a series of benchmark experiments dealing with the physics characteristics of a UN-fueled, Li-7 cooled, Mo-reflected, drum-controlled compact fast reactor for use with a space-power electric conversion system. The experimental program consisted basically of measuring the differential neutron spectra and the changes in critical mass that accompanied the stepwise addition of (Li-7)3N, Hf, Ta, and W to a basic core fueled with U metal in a pin-type Ta honeycomb structure. In addition, experimental results were obtained on power distributions, control characteristics, neutron lifetime, and reactivity worths of numerous absorber, structural, and scattering materials.

Heneveld, W. H.↗

NASA NTRS1982

Cyclic-inelastic deformation and fatigue resistance of notched-thin aluminum plates

The results of experiments designed to develop data to assess the accuracy and utility of the critical location concept in applications of fatigue-crack nucleation analysis at notch roots are presented and discussed. Fully reversed and nonzero mean-stress data are presented over a range of lives which encompass both elastic and inelastic deformations for thin-notched specimens and smooth specimens made of 2024 T351 aluminum-alloy sheet. Notch-root strains were measured via an extensometer, whereas the formation of small cracks was detected via an eddy-current transducer. Data reported indicated the validity of the assumption that smooth and notched specimens form cracks at the same cycle number when identical deformation histories are imposed at their respective critical locations. They also serve to demonstrate the accuracy and utility of the critical-location approach in analysis to predict the formation of small cracks at notches in coupons and components.

Leis, B. N.↗

NASA NTRS1996

Optimization Methodology for Unconventional Rocket Nozzle Design

Several current rocket engine concepts such as the bell-annular tripropellant engine, and the linear aerospike being proposed for the X-33, require unconventional three-dimensional rocket nozzles which must conform to rectangular or sector-shaped envelopes to meet integration constraints. These types of nozzles exist outside the current experience database, therefore, development of efficient design methods for these propulsion concepts is critical to the success of launch vehicle programs. Several approaches for optimizing rocket nozzles, including streamline tracing techniques, and the coupling of CFD analysis to optimization algorithms are described. The relative strengths and weaknesses of four classes of optimization algorithms are discussed: Gradient based methods, genetic algorithms, simplex methods, and surface response methods. Additionally, a streamline tracing technique, which provides a very computationally efficient means of defining a three-dimensional contour, is discussed. The performance of the various optimization methods on thrust optimization problems for tripropellant and aerospike concepts is assessed and recommendations are made for future development efforts.

Follett, W.↗