Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Component amounts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Measurements of DIII-D poloidal field by fiber-optic pulsed polarimetry

A new technique for measuring the spatial and temporal structure of the poloidal field is presented, whereby the magnetic field causes the polarization of light traveling through an optical fiber to rotate via the Faraday effect by an amount proportional to the strength of the field oriented along the fiber. In fiber optic pulsed polarimetry, changes in the polarization of the backscatter light from the fiber are detected, thereby permitting measurement of the field as a function of position along the fiber. In this proof-of-principle experiment, specially prepared single-mode fibers with weak fiber Bragg gratings were installed in the poloidal direction on the outside of the thermal blanket on DIII-D. Light at 532 nm from a mode-locked Nd:YAG laser was injected into the optical fibers. The laser repetition rate was 895 kHz with a pulse length of <10 ps, resulting in ~1 μs temporal resolution. A photodetector system measured the Stokes polarization components necessary to determine the amount of polarization rotation. For this experiment, bandwidth limitations of the detectors resulted in a spatial resolution of ≈2 cm. The measured temporal and spatial distributions of the poloidal field are consistent with inductive probe measurements and Elastodynamic Finite Integration Technique reconstructions of the spatial distribution. Furthermore, this demonstrates the ability of this technique to provide real-time detection of the temporal and spatial variations of the poloidal field. Besides revealing more detailed information about the plasma, this new diagnostic capability can also help in detecting instabilities in real time, thereby enabling enhanced machine protection.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Interacting radiation after Planck and its implications for the Hubble tension

Standard cosmology predicts that prior to matter-radiation equality about 41% of the energy density was in free-streaming neutrinos. In many beyond Standard Model scenarios, however, the amount and free-streaming nature of this component is modified. For example, this occurs in models with new neutrino self-interactions or an additional dark sector with interacting light particles. Here, we consider several extensions of the standard cosmology that include a non-free-streaming radiation component as motivated by such particle physics models and use the final Planck data release to constrain them. This release contains significant improvements in the polarization likelihood which plays an important role in distinguishing free-streaming from interacting radiation species. Fixing the total amount of energy in radiation to match the expectation from standard neutrino decoupling we find that the fraction of free-streaming radiation must be ffs > 0.8 at 95% CL (combining temperature, polarization and baryon acoustic oscillation data). Allowing for arbitrary contributions of free-streaming and interacting radiation, the effective number of new non-free-streaming degrees of freedom is constrained to be Nfld < 0.6 at 95% CL. Cosmologies with additional radiation are also known to ease the discrepancy between the local measurement and CMB inference of the current expansion rate H0. We show that including a non-free-streaming radiation component allows for a larger amount of total energy density in radiation, leading to a mild improvement of the fit to cosmological data compared to previously discussed models with only a free-streaming component.

particle physics - cosmology connection↗

Nanocoatings for High-Efficiency Industrial Hydraulic and Tooling Systems

Industrial manufacturing in the U.S. accounts for roughly one third of the 98 quadrillion Btu total energy consumption. Motor system losses amount to 1.3 quadrillion Btu, which represents the largest proportional loss of any end-use category, while pumps alone represent over 574 trillion BTU (TBTU) of energy loss each year. The efficiency of machines with moving components is a function of the amount of energy lost to heat because of friction between contacting surfaces. The friction between these interfaces also contributes to downtime and the loss of productivity through component wear and subsequent repair. The production of new replacement parts requires additional energy. Among efforts to reduce energy losses, wear-resistant, low-friction coatings on rotating and sliding components offer a promising approach that is fully compatible with existing equipment and processes. In addition to lubrication, one of the most desirable solutions is to apply a protective coating or surface treatment to rotating or sliding components to reduce their friction coefficients, thereby leading to reduced wear. Historically, a number of materials such as diamond-like carbon (DLC), titanium nitride (TiN), titanium aluminum nitride (TiAlN), and tungsten carbide (WC) have been examined as tribological coatings. The primary objective of this project was the development of a variety of thin film nanocoatings, derived from the AlMgB14 system, with a focus on reducing wear and friction in both industrial hydraulics and cutting tool applications. Proof-of-concept studies leading up to this project had shown that the constituent phases, AlMgB14 and TiB2, were capable of producing low-friction coatings by pulsed laser deposition. These coatings combine high hardness with a low friction coefficient, and were shown to substantially reduce wear in laboratory tribology tests. Selection of the two applications was based largely on the concept of improved mechanical interface efficiencies for energy conservation. In mobile hydraulic systems, efficiency gains through low friction would translate into improved fuel economy and fewer greenhouse gas emissions. Stationary hydraulic systems, accordingly, would consume less electrical power. Reduced tooling wear in machining operations would translate to greater operating yields, while lowering the energy consumed during processing. The AlMgB14 nanocoatings technology progressed beyond baseline laboratory tests into measurable energy savings and enhancements to product durability. Three key hydraulic markets were identified over the course of the project that will benefit from implementation: industrial vane pumps, orbiting valve-in-star hydraulic motors, and variable displacement piston pumps. In the vane pump application, the overall product efficiency was improved by as much as 11%. Similar results were observed with the hydraulic motors tested, where efficiency gains of over 10% were noted. For variable displacement piston pumps, overall efficiency was improved by 5%. For cutting tools, the most significant gains in productivity (and, accordingly, the efficiency of the machining process as a whole) were associated with the roughing and finishing of titanium components for aerospace systems. Use of the AlMgB14 nanocoating in customer field tests has shown that the coated tools were able to withstand machining rates as high as 500sfm (limited only by the substrate material), with relatively low flank wear when compared to other industrial offerings. AlMgB14 coated tools exhibited a 60% improvement over similarly applied TiAlN thin films. Furthermore, AlMgB14-based coatings in these particular tests lasted twice as long than their TiAlN counterparts at the 500sfm feed rates. Full implementation of the technology into the industrial hydraulic and cutting tool markets equates to a worldwide energy savings of 46 trillion BTU/year by 2030. U.S.-based GHG emissions associated with the markets identified would fall accordingly, dropping by as much as 50,000 tonnes annually.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Controllable deposition of platinum layers on oxide surfaces for the synthesis of fuel cell catalysts

Reducing the amount of Pt, the most costly component of both anode and cathode fuel cell catalysts, has attracted considerable attention from the research community. An approach is reported herein to deposit sub-monolayer to multilayer amounts of Pt and other noble metals on metal oxides and oxidized carbon materials. The process is exemplified by Pt deposition on RuO 2 (110). The Pt deposit consists of Pt atoms arranged in a c(2×2) array, that is, a 0.25 monolayer (ML). The deposit has lower catalytic activity for the oxygen reduction reaction (ORR) and similar activity for the hydrogen oxidation reaction compared to Pt(111). These activities are explained by a large calculated upshift of the d-band center of Pt atoms and larger Pt–Pt interatomic distances than those of Pt(111). A catalyst with Pt coverage larger than 0.25 ML on oxide surfaces and oxidized carbon materials is shown to be active for the ORR as well as for other electrocatalytic reactions. A PtRhSnO 2 /C catalyst shows high activity for ethanol oxidation as a result of its ability to effectively cleave the C–C bond in ethanol. Furthermore, Pt deposited on reduced graphene oxide shows high Pt mass ORR activity and good stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Assessing Internet energy intensity: A review of methods and results

Assessing the average energy intensity of Internet transmissions is a complex task that has been a controversial subject of discussion. Estimates published over the last decade diverge by up to four orders of magnitude — from 0.0064 kilowatt-hours per gigabyte (kWh/GB) to 136 kWh/GB. This article presents a review of the methodological approaches used so far in such assessments: i) top–down analyses based on estimates of the overall Internet energy consumption and the overall Internet traffic, whereby average energy intensity is calculated by dividing energy by traffic for a given period of time, ii) model-based approaches that model all components needed to sustain an amount of Internet traffic, and iii) bottom–up approaches based on case studies and generalization of the results. Our analysis of the existing studies shows that the large spread of results is mainly caused by two factors: a) the year of reference of the analysis, which has significant influence due to efficiency gains in electronic equipment, and b) whether end devices such as personal computers or servers are included within the system boundary or not. For an overall assessment of the energy needed to perform a specific task involving the Internet, it is necessary to account for the types of end devices needed for the task, while the energy needed for data transmission can be added based on a generic estimate of Internet energy intensity for a given year. Separating the Internet as a data transmission system from the end devices leads to more accurate models and to results that are more informative for decision makers, because end devices and the networking equipment of the Internet usually belong to different spheres of control. -- Highlights: • Assessments of the energy intensity of the Internet differ by a factor of 20,000. • We review top–down, model-based, and bottom–up estimates from literature. • Main divergence factors are the year studied and the inclusion of end devices. • We argue against extending the Internet system boundary beyond data transmission. • Decision-makers need data that differentiates between end devices and transmission.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Mechanism of N 2 Reduction Catalyzed by Fe-Nitrogenase Involves Reductive Elimination of H 2

Of the three forms of nitrogenase (Mo-nitrogenase, V-nitrogenase, and Fe-nitrogenase), Fe-nitrogenase has the poorest ratio of N 2 reduction relative to H 2 evolution. Current work on the Mo-nitrogenase has revealed that reductive elimination of two bridging Fe–H–Fe hydrides on the active site FeMo-cofactor to yield H 2 is a key feature in the N 2 reduction mechanism. The N 2 reduction mechanism for the Fe-nitrogenase active site FeFe-cofactor was unknown. Here, we have purified both component proteins of the Fe-nitrogenase system, the electron-delivery Fe protein (AnfH) plus the catalytic FeFe protein (AnfDGK), and established its mechanism of N 2 reduction. Inductively coupled plasma optical emission spectroscopy and mass spectrometry illustrate that the FeFe protein component does not contain significant amounts of Mo or V, thus ruling out a requirement of these metals for N 2 reduction. The fully functioning Fe-nitrogenase system was found to have specific activities for N 2 reduction (1 atm) of 181 ± 5 nmol NH 3 min –1 mg –1 FeFe protein, for proton reduction (in the absence of N 2 ) of 1085 ± 41 nmol H 2 min –1 mg –1 FeFe protein, and for acetylene reduction (0.3 atm) of 306 ± 3 nmol C 2 H 4 min –1 mg –1 FeFe protein. Under turnover conditions, N 2 reduction is inhibited by H 2 and the enzyme catalyzes the formation of HD when presented with N 2 and D 2 . These observations are explained by the accumulation of four reducing equivalents as two metal-bound hydrides and two protons at the FeFe-cofactor, with activation for N 2 reduction occurring by reductive elimination of H 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Solid-Binding Proteins: Bridging Synthesis, Assembly, and Function in Hybrid and Hierarchical Materials Fabrication

There is considerable interest in the development of hybrid organic–inorganic materials because of the potential for harvesting the unique capabilities that each system has to offer. Proteins are an especially attractive organic component owing to the high amount of chemical information encoded in their amino acid sequence, their amenability to molecular and computational (re)design, and the many structures and functions they specify. Genetic installation of solid-binding peptides (SBPs) within protein frameworks affords control over the position and orientation of adhesive and morphogenetic segments, and a path toward predictive synthesis and assembly of functional materials and devices, all while harnessing the built-in properties of the host scaffold. Furthermore, we review the current understanding of the mechanisms through which SBPs bind to technologically relevant interfaces, with an emphasis on the variables that influence the process, and highlight the last decade of progress in the use of solid-binding proteins for hybrid and hierarchical materials synthesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Aleurone Cell Walls of Wheat Grain: High Spatial Resolution Investigation Using Synchrotron Infrared Microspectroscopy

Infrared microspectroscopy and immunolabeling techniques were employed in order to obtain deeper insight into the biochemical nature of aleurone cell walls of wheat grain. The use of a synchrotron source, thanks to its intrinsic brightness, has provided unprecedented information at the level of a few micrometers and has allowed the discrimination of various polysaccharides in cell walls. The high spectral quality obtained in the small analyzed domain has been beneficial in estimating the relative proportions of {Beta}-glucan and arabinoxylan, through the use of principal component analysis (PCA). The highest amount of {Beta}-glucan is found in periclinal cell walls close to the starchy endosperm. The junction regions between aleurone cells are enriched in arabinoxylan. At the early stage of wheat grain development (271 degrees D), the chemical composition along the cell walls is more heterogeneous than at the mature stage. Both synchrotron infrared microspectroscopy and immunolabeling experiments made it possible to reveal the spatial heterogeneity of the various chemical compositions of aleurone cell walls.

43 PARTICLE ACCELERATORS↗

Fly Ash and Mercury Oxidation/Chlorination Reactions

Mercury is a known pollutant that has detrimental effect on human health and environment. The anthropogenic emissions of mercury account for 10 to 30% of worldwide mercury emissions. There is a need to control/reduce anthropogenic mercury emissions. Many mercury control technologies are available but their effectiveness is dependent on the chemical form of mercury, because different chemical forms of mercury have different physical and chemical properties. Mercury leaves the boiler in its elemental form but goes through various transformations in the post-combustion zone. There is a need to understand how fly ash and flue gas composition affect speciation, partitioning, and reactions of mercury under the full range of post-combustion zone conditions. This knowledge can then be used to predict the chemical transformation of mercury (elemental, oxidized or particulate) in the post combustion zone and thus help with the control of mercury emissions from coal-burning power plants. To accomplish this goal present study was conducted using five coal fly ashes. These ashes were characterized and their catalytic activity was compared under selected reaction conditions in a fixed bed reactor. Based on the results from these fly ash experiments, three key components (carbon, iron oxide and calcium oxide) were chosen. These three components were then used to prepare model fly ashes. Silica/alumina was used as a base for these model fly ashes. One, two or three component model fly ashes were then prepared to investigate mercury transformation reactions. The third set of experiments was performed with CuO and CuCl2 catalysts to further understand the mercury oxidation process. Based on the results of these three studies the key components were predicted for different fly ash compositions under variety of flue gas conditions. A fixed bed reactor system was used to conduct this study. In all the experiments, the inlet concentration of Hg0(g) was maintained at 35 {micro}g/m3 using a diffusion tube as the source of Hg0(g). All experiments were conducted using 4% O2 in nitrogen mix as a reaction gas, and other reactants (HCl, H2O and SO2, NO2, Br2) were added as required. The fixed bed reactor was operated over a temperature range of 200 to 400 C. In each experiment, the reactor effluent was analyzed using the modified Ontario-Hydro method. After each experiment, fly ash particles were also analyzed for mercury. The results show that the ability of fly ash to adsorb and/or oxidize mercury is primarily dependent on its carbon, iron and calcium content. There can be either one or more than one key component at a particular temperature and flue gas condition. Surface area played a secondary role in effecting the mercury transformations when compared to the concentration of the key component in the fly ash. Amount of carbon and surface area played a key important role in the adsorption of mercury. Increased concentration of gases in the flue gas other than oxygen and nitrogen caused decreased the amount of mercury adsorbed on carbon surface. Mercury adsorption by iron oxide primarily depended on the crystalline structure of iron oxide. {alpha}-Iron oxide had no effect on mercury adsorption or oxidation under most of the flue gas conditions, but ?-iron oxide adsorbed mercury under most of the flue gas conditions. Bromine is a very good oxidizing agent for mercury. But in the presence of calcium oxide containing fly ashes, all the oxidized mercury would be reduced to elemental form. Among the catalysts, it was observed that presence of free lattice chlorine in the catalyst was very important for the oxidation of mercury. But instead of using the catalyst alone, using it along with carbon may better serve the purpose by providing the adsorption surface for mercury and also some extra surface area for the reaction to occur (especially for fly ashes with low surface area).

54 ENVIRONMENTAL SCIENCES↗

Understanding Trends in Wind Turbine Prices Over the Past Decade

Taking a bottom-up approach, this report examines seven primary drivers of wind turbine prices in the United States, with the goal of estimating the degree to which each contributed to the doubling in turbine prices from 2002 through 2008, as well as the subsequent decline in prices through 2010 (our analysis does not extend into 2011 because several of these drivers are best gauged on a full-year basis due to seasonality issues). The first four of these drivers can be considered, at least to some degree, endogenous influences – i.e., those that are largely within the control of the wind industry – and include changes in: 1) Labor costs, which have historically risen during times of tight turbine supply; 2) Warranty provisions, which reflect technology performance and reliability, and are most often capitalized in turbine prices; 3) Turbine manufacturer profitability, which can impact turbine prices independently of costs; and 4) Turbine design, which for the purpose of this analysis is principally manifested through increased turbine size. The other three drivers analyzed in this study can be considered exogenous influences, in that they can impact wind turbine costs but fall mostly outside of the direct control of the wind industry. These exogenous drivers include changes in: 5) Raw materials prices, which affect the cost of inputs to the manufacturing process; 6) Energy prices, which impact the cost of manufacturing and transporting turbines; and 7) Foreign exchange rates, which can impact the dollar amount paid for turbines and components imported into the United States.

17 WIND ENERGY↗

Indoor Climate and Moisture Durability Performances of Houses with Unvented Attic Roof Constructions in a Mixed-Humid Climate

A sealed or unvented attic is an energy-efficient envelope component that can reduce the amount of energy a house consumes for space conditioning if the air handler and/or ducts are located in the attic. The attic is typically sealed by using spray foam on the underside of the roof deck and covering the soffit, ridge and gable vents to minimize air leakage from the attic to the outside. This approach can save up to 10% in space-conditioning energy when ducts are located in the attic (DOE 2013). Past research done by ORNL and Florida Solar Energy Center suggests that in more hot, humid climates, an unvented attic could potentially create a more humid, uncomfortable living environment than a vented attic (Colon 2011, Boudreaux, Pallin et al. 2013). Research showed that controlling the higher indoor humidity could reduce the energy savings from the sealed, unvented attic, which in turn would decrease the energy savings payback. Research also showed that the roof assembly (5.5 inches of open-cell foam, 1inch of closed-cell foam, OSB, felt paper, and asphalt shingles) stored moisture, thus acting as a moisture buffer. During the fall and winter, the roof assembly stored moisture and during the spring and summer it released moisture. This phenomenon is not seen in a vented attic, in which the air exchange rate to the outside is greater and, in the winter, helps to dehumidify the attic air. It was also seen that in a vented attic, the direction of water vapor diffusion is on average from the attic to the interior of the house. Air leakage from the attic to the interior also occurs during more of the year in a house with an unvented attic than in one with a vented attic. These discoveries show that the moisture dynamics in a house with an unvented attic are much different from those in a house with a vented attic. This study reports on a series of computer model investigations completed to determine the key variables impacting indoor comfort and the durability of roof assemblies against moisture. The key variables investigated were the leakage area from the attic to the outside, leakage area from the attic to the interior, leakage area from the interior to the outside, supply duct leakage in the attic, and interior moisture generation. These investigations are described in this report.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Future Recovered Gas Dryer Development

Building on our successful development of a water detritiation process, this project was extended to ammonia detritiation using a catalytic isotope exchange process with hydrogen (H 2 ) for the next generation of RGD materials. In these processes, isotopic exchange between flowing H 2 with adsorbed tritiated species is facilitated by trace amounts of an active catalyst component (e.g. Pt) that is loaded onto a zeolite. Since the catalyst loading may alter the zeolite pore size, Pt/zeolite performance for moisture and ammonia adsorption underwent verification in addition to characterization of the remediation process. The performance was evaluated for catalytic isotope exchange of deuterated water and deuterated ammonia (surrogates) with H 2 at ambient temperatures.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

EXPERIMENTAL INVESTIGATION OF IMPACT AND ABRASION EROSIONS AT LOW VELOCITIES AND COMPARISON TO CFD SIMULATIONS

Wear and erosion damage of materials due to interaction of the surface with solid particles is a major issue in various industries. This phenomenon is common in mining, and oil and gas production, causing damages worth millions of dollars annually. Erosion is becoming a critical issue in renewable technologies as well such as concentrated solar thermal power (CSP) systems. In some CSP systems, solid particles can be used to absorb solar energy and enhance the heat storage. However, these particles may cause significant amount of wear to system components while falling down the power tower at high temperatures. This damage can be costly, and therefore, investigating solid particle erosion in CSP systems is of utmost importance. In collaboration with Sandia National Laboratories, the erosion durability of particle-based Generation 3 (GEN3) CSP system are being investigated both experimentally and numerically. In order to develop models to predict the life time of such systems, erosion under low temperature and low particle impact velocity conditions are investigated. Impact erosion and abrasion erosion experiments are conducted for low velocity and low temperature conditions for various candidate particles and containment materials. The impact erosion testing is conducted for three different containment material including Stainless Steel 316, special refractory material, and Inconel 740H with CARBOBEAD HSP 40/70 ceramic particles and UNIWEST 430 silica quartz erodent particles. All this data will enable us to better model the erosion behavior of these materials and provides a data base to investigate erosion at high temperatures experienced in CSP systems. At low temperatures and low velocities the softer refractory material exhibited greater erosion by an order-of-magnitude when compared to the harder Inconel 740H and Stainless Steel 316 materials. The overall erosion ratio for all the candidate materials was of the order of 10 -7 kg/kg. We also investigated wear in containment materials from sliding of particles over the surfaces at very low angles, also referred to as abrasion. For the velocities expected in a typical 1MW CSP plant, visible surface wear was noted, but the overall mass loss per unit surface area was found to be dependent on the hardness of the containment material tested. In this manuscript, we also present Computational Fluid Dynamics (CFD) simulations and erosion prediction of low velocity impact erosion. These results are compared with the experimental data to evaluate the ability of available erosion models for predicting erosion under these conditions.

14 SOLAR ENERGY↗

High Temperature Erosion Modeling in Particle Based CSP Systems

1. Introduction. Wear and erosion damage of materials from solid particle and surface interactions is a major issue in various industries. Although more common in mining and oil and gas production, erosion is becoming a critical issue in renewable technologies as well such as particle based concentrated solar thermal power (CSP) systems. In particle based CSP systems, solid particles are used to absorb solar energy and as thermal storage. However, these particles may cause significant amount of wear to system components while through the system at high temperatures. This damage can be costly, and therefore, requires a greater understanding of solid particle erosion in CSP systems. Throughout the years, models and tools have been developed to predict and control erosion in industries such as oil and gas production. However, these erosion models and erosion prediction tools have been mainly developed based on erosion data for much higher velocities and lower temperatures, i.e. the operating conditions for which the existing models have been built are not pertinent to those expected in CSP system. It is known that erosion depends on many factors such as material properties, erodent particle properties, and particle impact speed and angle. However, the effect of temperature on erosion is not vastly investigated. In this work, a temperature-based correlation is introduced that will be used to modify the existing erosion models to predict erosion rates at velocities and temperatures relevant to Gen3 CSP systems. The existing models are first validated against erosion experiments run at low temperatures and low velocities. Subsequently, a temperature correction term is developed that can extend the existing models to high temperatures, based on the available experimental data showing the effect of temperature on impact erosion. 2. Erosion Models. Continuing sequence of impacts from solid particles on surfaces would result in loss of material due to mechanical interaction between solid surface and particles. Erosion equations have been developed to predict erosion under different conditions and erosion mechanism, including cutting and deformation erosion. These models are mainly either mechanistic, empirical, and semi-mechanistic models, when the latter combine the theory of the erosion mechanism and particle motion with the available experimental data. One of the first empirical correlation was introduced by American Petroleum Institute (API) Recommended Practice (RP) 14E [1]. This correlation was very conservative, and several improved empirical and semi-mechanistic equations were developed in the years following. More recently, the models introduced by Erosion/Corrosion Research Center (E/CRC) at the University of Tulsa and Arabnejad. et al. [2] are frequently used in the literature and industry, as they account for many parameters affecting erosion including particle impact speed and angle, material density and hardness, and particle size and shape. However, both these models were developed based on data at relatively high velocities and also do not take into account any mechanical changes in material associated with thermal cycling at high temperatures. 3. Erosion Prediction at High Temperatures. In this work, the accuracy of Arabnejad et al. model and E/CRC model is investigated to predict impact erosion at conditions relevant to Gen3 CSP systems. Two significant deviations expected in Gen3 systems compared to operating conditions used to build these models are particle impact velocities and system temperature. As a first step, the performance of these models was validated at low velocities and temperatures. Impact erosion experiments were conducted on SS316 coupons using HSP 40/70 ceramic particles. Assuming particle rate of 1 kg/s/m, 0.0254 m of particle curtain thickness, and particle velocity of 1.5 m/s in the system, an overall erosion of 0.59 mm/year was calculated. The experimental results were subsequently compared to those from computational simulations and erosion of 0.47 mm/year was obtained using the Arabnejad et al. model. The results indicated that the models work well at low velocities and low temperature conditions. To account for temperature effect, a mathematical correlation was developed using data published by DUCOM [3] for Inconel 600 eroded by alumina particles at high velocities. The correlation was applied to both Arabnejad et. al model and the E/CRC model. The prediction results from these modified models were within 20% of this experimental data. Predictions of of erosion by the modified E/CRC model at three different temperatures are made. Similar to the calculation at low temperature, a typical CSP system with 1 kg/s/m of particle flow rate per unit length of the particle curtain and a curtain thickness of 0.0254 m is assumed. The annual thickness loss calculations were run for different particle impact velocities, assuming a uniform particle impact area equal to the cross-sectional area of the curtain (particle-particle interactions and dispersion of particles are not considered in obtaining the results). It is observed that erosion increases exponentially as temperature increases. Furthermore, it is also noted that, erosion changes non-linearly with impact velocity. Currently, experiments are also being conducted to measure erosion of SS316 at 800 ºC with HSP 40/70 particles at low impact velocities. We expect to use the results from high temperature testing to further improve the temperature correlation function. Similar models are also being developed for abrasion erosion resulting from particle sliding along the surfaces as well as attrition from particle to particle and particle to surface interactions. References. [1] Institute, A. P. (1991). API Recommended Practice for Design and Installation of Offshore Production Platform Piping System, API RP 14E. [2] Arabnejad, H., Mansouri, A., Shirazi, S. A., and McLaury, B. S. (2015a). Development of mechanistic erosion equation for solid particles. Wear, 332–333, 1044–1050. http://doi.org/10.1016/j.wear.2015.01.031. [3] https://ducom.com/high-temperature-erosion-evaluating-sample-wear/

14 SOLAR ENERGY↗

Design, Synthesis and Study of Dendrimers as Nanoscaffolds for Solar Energy Harvest

Designing molecules in which the vectorial motions of charges can be controlled has been of significant research interest in the recent past. Covalent linear arrays of chromophores or other molecular assemblies such as liquid crystals, zeolites, polymers, peptides, and amphiphiles have all been used as components for this purpose. Significant amount of this effort also involved the use of dendrimers as the molecular architecture. The structural feature in which multiple functionalities are present in the periphery that decreases gradually as one moves towards the core renders dendrimers obvious candidates for light harvesting antenna. Most of the efforts reported in the literature are directed towards energy funneling from a chromophore in the periphery to another chromophore at the core of the dendrimer. There are relatively few reports that utilize the dendritic architecture for photoinduced charge separation, an important step in designing materials for photovoltaics. These reports focus mostly on conjugated molecular backbones. Since non-conjugated dendrimer backbones provide the possibility of independently tuning the electronic characteristics of the chromophore and the charge transfer unit and therefore carry out a systematic structure-property relationship study, we have designed and synthesized dendrimers

molecular design↗

Design, Synthesis and Study of Dendrimers as Nanoscaffolds for Solar Energy Harvest

Designing molecules in which the vectorial motions of charges can be controlled has been of significant research interest in the recent past. Covalent linear arrays of chromophores or other molecular assemblies such as liquid crystals, zeolites, polymers, peptides, and amphiphiles have all been used as components for this purpose. Significant amount of this effort also involved the use of dendrimers as the molecular architecture. The structural feature in which multiple functionalities are present in the periphery that decreases gradually as one moves towards the core renders dendrimers obvious candidates for light harvesting antenna. Most of the efforts reported in the literature are directed towards energy funneling from a chromophore in the periphery to another chromophore at the core of the dendrimer. There are relatively few reports that utilize the dendritic architecture for photoinduced charge separation, an important step in designing materials for photovoltaics. These reports focus mostly on conjugated molecular backbones. Since non-conjugated dendrimer backbones provide the possibility of independently tuning the electronic characteristics of the chromophore and the charge transfer unit and therefore carry out a systematic structure-property relationship study, we have designed and synthesized dendrimers.

14 SOLAR ENERGY↗

NUHOWS - Storage and Transportation of Irradiated Reactor Components in Large Packages - 13439

Most irradiated reactor components (hardware such as Control Rod Blades, Fuel Channels, Poison Curtains, etc.) generated at reactors previously required significant processing for size reduction due to the available transportation casks not being physically capable of containing unprocessed material. As of July 1, 2008, disposal for this typical waste class (B and C) became inaccessible (for the major part of the nation) due to the Barnwell, SC disposal facility being closed to all but its three compact states (CT, NJ and SC). Currently in the United States, most facilities are storing their irradiated hardware on-site in the spent fuel pools. Until recently with the opening of the Waste Control Specialists' Texas disposal facility, utilities faced the challenges of spent fuel pool space and capacity management. However, even with WCS's disposal availability, the site currently has annual Curie limitations for disposal, which will continue to promote interim on-site storage until such time as disposal is available. In response, Transnuclear Inc., (TN) an AREVA company, proceeded with designing a new large Radioactive Waste Container (RWC) that can be used to package irradiated hardware without the need for significant processing. The design features of the RWC allows for intermittent loadings of the hardware for better packaging efficiency, higher packaging density, space savings and reduced cost. This RWC is also compatible with TN's on-site modular vault storage system. Once completely loaded, the RWC can be transported to an on-site storage facility, an off-site storage facility and/or an available disposal facility. To accommodate the transportation, TN has designed a large transportation cask, the MP197HB. As the original design was for transporting fuel, it contains the necessary shielding to allow for the transport of unprocessed irradiated reactor components, while significantly reducing the amount of irradiated hardware shipments required with the use of the new RWC. This paper provides information on the unique design features of the RWC, storage module vaults, MP197HB Transportation Cask and cost saving benefits of using the large RWC for packaging, storage, transport and disposal. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Groundwater Remediation in a Flood plain Aquifer at Shiprock, New Mexico - 16097

The Shiprock, New Mexico, Disposal Site is the location of a former uranium and vanadium ore-processing mill that operated from 1954 to 1968. During milling years, tailings leachate and other mill-related liquids migrated into underlying sediments, resulting in the contamination of groundwater beneath the river terrace containing the mill and a nearby flood plain alluvial aquifer adjacent to the San Juan River. The US DOE Office of Legacy Management manages the site and is implementing the current groundwater remedy for the flood plain area, consisting of natural flushing supplemented by extraction of alluvial groundwater to accelerate reduction in contaminant concentrations. The alluvial aquifer contains elevated concentrations of sulfate, uranium, and nitrate derived largely from the historical eastward migration of groundwater through terrace alluvium and underlying bedrock to the flood plain. The bedrock formation beneath the entire Shiprock site is Mancos shale, which forms an escarpment that separates the terrace from the flood plain. Contamination in the flood plain alluvial aquifer is influenced by a dynamic flow system that changes seasonally and from year to year. Simulations with a flood plain flow model based on monitored groundwater levels and coincident river-surface elevations show that background groundwater flow, unaffected by remediation pumping, is characterized by distinct hydraulic conditions for three separate periods each year. During months of low river flow in winter and early spring, river losses to the aquifer create a large hypo-rheic zone in the south half of the flood plain. Simultaneously, recharge of continually flowing surface water emptying onto the north half of the flood plain from Bob Lee Wash creates divergent, radial flow from the wash outlet and diverts northwestward-migrating contaminant plumes to the northeast where they discharge to the river. Subsequent bank storage processes in May and June from high snow melt runoff change background flow directions, increasing the spread of contamination in the alluvium. From mid-summer through fall, river flows are typically similar in value to those observed prior to the onset of snow melt, but groundwater elevations in the aquifer are noticeably lower than water levels observed in winter and early spring and may induce river losses to the aquifer. Several different contaminant sources have impacted the alluvial aquifer. Much of the contamination originated as tailings leachate and raffinate wastewater that infiltrated the terrace subsurface and eventually reached the flood plain at the escarpment. Additional sources of contamination in the aquifer included discharge of mill effluent to Bob Lee Wash and a pond at the base of the escarpment, and aqueous mobilization of solid-phase contamination in the form of windblown deposits and contaminants adsorbed to alluvial sediments. The degree to which remnant, secondary-source processes, such as leaching of solid-phase deposits and discharge of terrace groundwater across the escarpment, contribute to existing contaminant plumes is uncertain. The flood plain remediation system consists of two groundwater extraction wells, pumping from two horizontal wells placed in trenches near the base of the escarpment, a sump collecting discharges from seeps in the escarpment wall, and discharge of collected water to an evaporation pond on the terrace. Flow-model simulations indicate that most contaminated areas are captured by remediation pumping, resulting in several zones of freshwater between the river and the escarpment. Despite the highly transient nature of groundwater flow beneath the flood plain and the varied contaminant sources, initiation of remediation pumping in 2003 and coordinated operation of the system's various components have successfully removed large amounts of contaminant mass and helped prevent discharge of contaminated groundwater to the river. The percentage reductions of dissolved sulfate, uranium, and nitrate mass in the aquifer estimated for the first 9 years of remediation range from 40% to 72%. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗