Results for “Coding Guidelines” — Page 5

DOE OSTI2019

Radiological Performance Modeling: Platform Comparison

Zapadnoe Uranium Mill Tailings Site, Pridneprovsky Chemical Plant Ukraine: Two exposure scenarios were utilized to develop performance assessment models in GoldSim and NORMALYSA. The first scenario is an onsite worker exposed to radioactivity through external ground irradiation as well as radon and radioactive dust inhalation. The second being an offsite Resident 300 years after institutional control exposed through the ingestion of garden vegetables irrigated by contaminated ground water, ingestion of fish from Konoplyanka River, and agricultural activities in contaminated garden. NORMALYSA utilizes a modular interface to connect extensive pre-created modules to develop contaminant transport and risk assessment models for safety assessments and performance assessments at NORM and legacy sites. Developed by Facilia AB, the program was tested with the creation of the Zapadnoe model under the International Atomic Energy Agency MODARIA Il Working Group 1 (WG1). Default values are provided for input parameters where site specific data and distributions lack. Probabilistic simulations and inputs are limited to parameters with assigned Gaussian probability functions. Similar results for transient worker inhalation dose were found in comparison with the Zapadnoe GoldSim model. However, the NORMALYSA model has results larger by an order of magnitude for external radiation in the transient worker and for aquatic food ingestion, inhalation, and garden food ingestion to the resident. Performance Assessment Modeling: Radiological performance models promote good management and support in remediation and environmental decision making by optimizing radioactive waste disposal site performance. a performance assessment model of the Zapadnoe uranium mill tailings site and a model for calculating authorized limits at Los Alamos National Laboratory are created to demonstrate and highlight the respective capabilities of three modeling platforms: GoldSim, NORMALYSA, and RESRAD-Onsite. GoldSim is a general-purpose modeling platform with the ability to simulate site-specific FT radionuclide transport and risk assessment using a graphical interface to create and link elements that act as indivisible building blocks of the model. The Zapadnoe performance assessment model created in GoldSim is composed of input parameters collected from site specific parameters from WG1 as well as standard assumptions seen in the Generic PA Model from Neptune and Company. The multivariate Zapadnoe simulation contains both deterministic and probabilistic simulation capabilities with the ability to quantitatively represent the uncertainty and associated risks of the site via the Monte Carlo simulation method. Model parameters, documentation, and assumptions are built directly into the model creating a transparent, reproducible, and more purposeful site specific model. To demonstrate this, an ingestion of water pathway was included in addition to the exposure pathways included in the NORMALYSA model. GoldSim offers a wide variety of probability distributions to choose from as well as many tools to visualize the uncertainty of the models and explore which pathways and radionuclides dominate dose. In contrast to the NORMALYSA model, the GoldSim model uses dynamic simulation to calculate tritium concentrations. Authorized limits support the evaluation of radiological health effects from radionuclides present in bulk contaminated soil in order to assist in the process of clearing land for release under different uses. Calculations of authorized limits in RESRAD-Onsite and GoldSim models support the evaluation for 15 radionuclides using a residential exposure scenario, indoor and outdoor inhalation of dust and vapor phase radionuclides (tritium), incidental soil ingestion, and ingestion grown fruits and Vegetables. RESRAD-Onsite, developed by Argonne National Laboratory is a dedicated computer code for calculating radiation doses and cancer risks to an individual located on top of radioactively contaminated soils. It can also be used to provide guidelines for deriving radionuclide soil levels corresponding to a specific dose criterion. The menu driven user interface facilitates selection of radionuclides and soil concentrations, as well as defines parameter values related to materials, environmental factors, and exposure pathways. The program contains radionuclide-specific data such as dose conversion factors and risk coefficients, as well as soil-water partition coefficients and transfer factors for biotic media. The GoldSim model successfully emulates the RESRAD-Onsite code using identical radiological decay and ingrowth factors, radiation dose conversion factors, and other input parameters. DE EEDE ETS Each model supports dynamic modeling of radionuclide ingrowth and decay over time, and integrate this capability with the transport of radionuclides in the environment via processes such as advection and/or diffusion in fluids, or within porous solid media, The applicability of each program is heavily dependent on project context. In the context of developing Authorized Limits, RESRAD-Onsite may be a more desirable option as it was developed for this particular application. For simple disposal or legacy sites or sites that do not need site-specific model structure, NORMALYSA may be a desirable modeling platform, GoldSim can be used to model any problem for which RESRAD or NORMALYSA is applicable, but its strength lies in its flexibility, analytical, and probabilistic capabilities.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2023

Model Energy Codes End-Use Opportunity Analysis

Model energy codes (ASHRAE Standard 90.1 and IECC) has significantly impacted programs and policies aimed at improving energy efficiency both in United States and across the globe. Standard 90.1, first published in 1975 (originally referred to as Standard 90) provides minimum energy efficiency guidelines for designing, constructing, operating, and maintaining new construction and renovated buildings. It is updated continuously, with new editions published every 3 years. Pacific Northwest National Laboratory (PNNL) conducts simulated energy and cost savings analysis of model energy codes to determine their expected impact and to track progress toward net-zero goals and efficiency targets. Additionally, the simulation outputs are examined to assess how energy is used across primary systems within prominent U.S. commercial building types to understand how energy is used in each building type at the end-use level and to identify areas for improvements in future code cycles. This end-use opportunity analysis of model energy codes provides ASHRAE technical committees and other interested parties a better understanding of how the Standard affects various building systems and end uses, specifically, those in the Standard that most prominently influence energy efficiency. Additionally, findings provide industry stakeholders guidance in identifying building types and end-uses with the most potential for energy efficiency improvements through energy codes and those that may require beyond code measures to meet energy use reduction targets. This paper summarizes features and functionalities of a webtool created by PNNL to explore and visualize the End-Use opportunity analysis.

ASHRAE 90.1, Energy Codes, Tableau↗

DOE OSTI2023

Linguistic variation in functional types of statutory law

When the meaning of an ambiguous word, phrase or grammatical structure in a statutory provision is disputed, courts are tasked with identifying the best meaning of the contested language. A common method of resolving linguistic ambiguities is to investigate the meaning of the contested word or structure in statutory provisions with similar subject matter. While the subject matter of a text has a demonstrated effect on language use, register variation research shows that the function of a text is also highly influential in predicting linguistic variation. Thus far, the function of a statutory provision (e.g., obligation to act, authorization to act) has not been considered in legal interpretative research. In the present study, I investigate the extent to which function influences the lexico-grammatical characteristics of statutory texts. 2,573 statutory provisions from the Arizona State Code are individually assigned to one of seven categories representing their function: Duties, Permissions, Impersonal Rules, Operational Definitions, Prohibitions, Procedural Guidelines, and Criminal Offenses. Key feature analysis is used to identify and describe patterns of lexico-grammatical variation between the seven functional types. Results reveal a great deal of lexico-grammatical variation associated with function in the register of statutory law. Furthermore, some functional types of statutory provisions are more linguistically distinct than others. In conclusion, these findings suggest that it may be beneficial to consider communicative function when investigating legal interpretative questions.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2017

A NOVEL TOOL FOR IMPROVING THE DATA COLLECTION PROCESS DURING CONTROL ROOM MODERNIZATION HUMAN-SYSTEM INTERFACE TESTING AND EVALUATION ACTIVITIES

The U.S. Department of Energy (DOE) Light Water Reactor Sustainability (LWRS) Program is developing a scientific basis to extend the existing U.S. nuclear power plant (NPP) operating life beyond the current 60-year licensing period and to ensure NPP long-term reliability, productivity, safety, and security. Under the Advanced Instrumentation, Information, and Control (II&C) Systems Technologies pathway, the LWRS Program conducts targeted research and development to address long-term aging and obsolescence of existing instrumentation and control technologies, as well as to implement and test new digital II&C technology that enables broad innovation and business improvement in the NPP operating model. To this end, the role of human factors engineering (HFE) is important as part of ensuring that the control room modernization (CRM) activities account for the operator’s cognitive and physiological characteristics. Part of the HFE process for CRM entails conducting tests and evaluations (T&Es) that will inform the design of new human-system interface (HSI) technologies. Qualitative data that captures operator feedback and important human-system interactions are an important part of T&E. However, the analyzing this qualitative data in order to provide actionable design recommendations can be time-consuming and error prone. This paper presents an early version of a tool that can be used to analyze this qualitative data to (1) sift through freeform text for improved design issue identification, (2) maintain consistency in theme coding conventions, and (3) readily provide actionable design guidance that can be traceable to state-of-the-art HFE guidelines such as NUREG-0700. A description of this tool is discussed next.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2017

A novel tool for improving the data collection process during control room modernization human-system interface testing and evaluation activities - 271

The U.S. Department of Energy (DOE) Light Water Reactor Sustainability (LWRS) Program is developing a scientific basis to extend the existing U.S. nuclear power plant (NPP) operating life beyond the current 60-year licensing period and to ensure NPP long-term reliability, productivity, safety, and security. Under the Advanced Instrumentation, Information, and Control (II and C) Systems Technologies pathway, the LWRS Program conducts targeted research and development to address long-term aging and obsolescence of existing instrumentation and control technologies, as well as to implement and test new digital II and C technology that enables broad innovation and business improvement in the NPP operating model. To this end, the role of human factors engineering (HFE) is important as part of ensuring that the control room modernization (CRM) activities account for the operator's cognitive and physiological characteristics. Part of the HFE process for CRM entails conducting tests and evaluations (T and Es) that will inform the design of new human-system interface (HSI) technologies. Qualitative data that captures operator feedback and important human-system interactions are an important part of T and E. However, the analyzing this qualitative data in order to provide actionable design recommendations can be time-consuming and error prone. This paper presents an early version of a tool, which uses a combination of natural language processing and supervised machine learning to support the analysis of qualitative data. The objectives of this tool is to improve the process of (1) sifting through freeform text for improved design issue identification, (2) maintaining consistency in theme coding conventions, and (3) readily providing actionable design guidance that can be traceable to state-of-the-art HFE guidelines such as NUREG-0700. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2016

PCI margin analysis methodology using the FALCON fuel performance code

ANATECH Corp., a wholly owned subsidiary of Structural Integrity Associates, Inc. has been at the forefront of PCI (pellet-cladding interaction) margin analyses as principal author of the EPRI PCI Guidelines documents and through the performance of numerous PCI margin evaluations for light-water reactors. In this paper, ANATECH first provides a discussion of specific features of the methodology developed over a number of years of application including a) selection of limiting assemblies for the detailed FALCON full length fuel rod (i.e., R-Z model) and PCI (i.e., R-θ model) evaluations, b) development of FALCON input characteristics including high fidelity rod-by-rod power histories, and c) application of failure criteria and remedies to the core designer in the case where the criteria are exceeded. Second, ANATECH provides guidance based on evaluations performed to-date. Analysis results are presented to show critical aspects of the evaluations and how they are used to provide insights to inform and improve commercial plant operation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2018

GALE 3.1 Verification Report

This report is documentation of the verification activities that have been performed on GALE-3.1 to ensure that the codes meet the requirements and specifications set forth by NRC and that the code meets its intended purpose. Additional benchmark tests for GALE-3.1 are documented in Appendix A of NUREG-0016, Revision 2 for GALE-BWR 3.1 and Appendix A of NUREG-0017, Revision 2 for GALE-PWR 3.1. These activities are done in accordance with the GALE Software Quality Assurance Plan (PNNL-24249) and the GALE Configuration Management & Maintenance Plan (PNNL-24250). These two plans meet the requirements set for by both PNNL software quality assurance requirements and the NRC’s Software Quality Assurance Program and Guidelines (NUREG/BR-0167). The verification activities are documented to conform to Level 2 requirements of NUREG/BR-0167. Verifications were performed for both GALE-3.1 BWR and GALE-3.1 PWR Codes. The GALE 3.1 BWR and PWR codes are computerized mathematical models for calculating the releases of radioactive material in gaseous and liquid effluents. These computer codes are tools which can be used to determine conformance with the requirements of Appendix I to Title 10, Part 50 of the Code of Federal Regulations (10 CFR 50).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2019

Extreme Load Computational Fluid Dynamics Analysis and Verification for a Multibody Wave Energy Converter

A wave energy converter (WEC) must be designed to survive the extreme sea states that it will be subject to throughout its lifetime. Although there are many analysis methods and codes available to accomplish this, there are currently several engineering challenges to WEC survival design. Foremost, the computational design approach will typically involve a trade-off between accuracy and computational efficiency. Additionally, most computational fluid dynamics (CFD) codes are not ideally suited to modeling extreme events for WECs with multibody dynamics, power-take-off systems, and mooring systems. Finally, although WEC design standards and CFD guidelines are emerging, with the current immaturity of the WEC industry, they are not yet well established. In this study, loads on a 1:35-scale, moored, multibody WEC are evaluated with CFD. The CFD results are compared with results obtained from a computationally efficient, midfidelity model based on linearized potential flow hydrodynamics. For these model verification comparisons, both operational and survival configurations are considered. The extreme load results obtained, using both codes, indicate that the survival configuration successfully sheds loads during extreme sea states. It is also found that WEC-Sim, when appropriately applied, can provide reasonable load results, at a fraction of the computational expense of CFD. However, for the more extreme sea states, and for higher-order effects not included in the WEC-Sim model, the linear-based results have significant errors in comparison to the CFD-based results, and should be used judiciously.

16 TIDAL AND WAVE POWER↗

DOE OSTI2019

Extreme Load Computational Fluid Dynamics Analysis and Verification for a Multibody Wave Energy Converter: Preprint

A wave energy converter (WEC) must be designed to survive the extreme sea states that it will be subject to throughout its lifetime. Although there are many analysis methods and codes available to accomplish this, there are currently several engineering challenges to WEC survival design. Foremost, the computational design approach will typically involve a trade-off between accuracy and computational efficiency. Additionally, most computational fluid dynamics (CFD) codes are not ideally suited to modeling extreme events for WECs with multibody dynamics, power-take-off systems, and mooring systems. Finally, although WEC design standards and CFD guidelines are emerging, with the current immaturity of the WEC industry, they are not yet well established. In this study, loads on a 1:35-scale, moored, multibody WEC are evaluated with CFD. The CFD results are compared with results obtained from a computationally efficient, midfidelity model based on linearized potential flow hydrodynamics. For these model verification comparisons, both operational and survival configurations are considered. The extreme load results obtained, using both codes, indicate that the survival configuration successfully sheds loads during extreme sea states. It is also found that WEC-Sim, when appropriately applied, can provide reasonable load results, at a fraction of the computational expense of CFD. However, for the more extreme sea states, and for higher-order effects not included in the WEC-Sim model, the linear-based results have significant errors in comparison to the CFD-based results, and should be used judiciously.

16 TIDAL AND WAVE POWER↗

DOE OSTI2026

NGEE Arctic Authorship Guidelines

Authorship Guidelines were developed to help facilitate trust among team members as we span multiple institutions, scientific disciplines, and career stages. NGEE Arctic was built on a foundation of open science, data sharing, and collaboration. In Phase 4 of the project, it was particularly important to keep this foundation in mind as we develop new collaborations across the Arctic. Included in this package is one *.pdf. The Next-Generation Ecosystem Experiments in the Arctic (NGEE Arctic) project is a research effort to reduce uncertainty in the Department of Energy’s Energy Exascale Earth System Model (E3SM) by developing a predictive understanding of Arctic tundra ecosystems underlain by permafrost and to quantify feedbacks from the Arctic tundra to the Earth system. NGEE Arctic is supported by the Department of Energy's Office of Biological and Environmental Research. Over Phases 1–3, observations made by the NGEE Arctic team across a gradient of permafrost landscapes in Arctic Alaska improved the representation of tundra processes in the land surface component of E3SM (the E3SM Land Model, ELM). Model improvements emphasized unique aspects of permafrost environments and explored reductions in model complexity while retaining predictive power. The Arctic-informed ELM developed by NGEE Arctic has been used to make novel predictions on processes ranging from permafrost thaw to soil biogeochemical cycling to Earth system feedbacks associated with the unique characteristics of tundra plants. In Phase 4, the NGEE Arctic team is evaluating our new predictive understanding under novel conditions across the Arctic domain. In collaboration with partners at long-term pan-Arctic research sites we are examining whether an Arctic-informed ELM can faithfully simulate interactions among surface and subsurface processes at site, regional, and pan-Arctic scales. In turn, we are using variety of tools to dynamically extend and evaluate ELM inference, with an emphasis on data synthesis and pan-Arctic model evaluation, reintegration of code with an evolving E3SM, scaling across heterogeneous Arctic landscapes, and the appropriate representation of the impacts of increasingly frequent Arctic disturbances.

Iversen, Colleen [ORNL] (ORCID:0000000182933450)↗

DOE OSTI2023

Advanced Fuel Cycle Cost Basis Report: Supporting Documents 2 Production Based Costing

The purpose of this section is to outline a method of cost analysis whereby a significantly better representation of “should achieve” costs may be attained for NOAK systems. Based on economists’ notions of producer theory, and grounded in the cost analysts’ and project managers’ tool called the Work Breakdown Structure (WBS), this section describes best practices in cost estimation. It then illustrates how the Code of Accounts (COA) structure, developed by the Economic Modeling Working Group (EMWG) of the Generation IV International Forum in “Cost Estimating Guidelines for Generation IV Nuclear Energy Systems [EMWG 2007] (hereafter “Gen IV Guidelines Document”), can be used to differentiate “should achieve” versus “did experience” costs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

ASME Section III, Division 5, High Temperature Reactors

Section III, Division 5 stands ready to support near-term deployment of advanced reactors. Progress on improving design rules, extending design lifetimes, adding more materials, and adding advanced component fabrication methods. Lessons-learned from Alloy 617 Code Case effort have streamlined the balloting workflow for Class A material code cases. After requester submitted material design parameters and supporting data package to ASME, Division 5 could turn around a material code case in about three Code Week cycles (less than a year). Data requirements for new materials are described in Division 5, “Nonmandatory Appendix HBB-Y, Guidelines For Design Data Needs For New Materials”.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Added value for integrated marine energy data systems

Launched in 2019, the Portal and Repository for Information on Marine Renewable Energy (PRIMRE) provides centralized access, standardization, community building, and integration of United States (U.S.) databases, tools and codes, and other resources that cover a range of marine energy information. The PRIMRE universe contains a series of Knowledge Hubs that represent data and information on testing of marine energy devices (MHKDR); environmental effects (Tethys); engineering and technical papers (Tethys Engineering); descriptions of marine energy companies and technologies (Marine Energy Projects Database); codes and models (Marine Energy Software); and guidance on testing and measurements (Telesto). Content is added to PRIMRE by applying a set of Guidelines and Best Practices (PRIMRE Guidelines). An aggregate search across the PRIMRE site enables users to find data and information from all the PRIMRE Knowledge Hubs simultaneously, using a single entry-point (PRIMRE Search). In addition to providing access to a range of data and information on marine energy development, testing, and effects, PRIMRE allows for the development of value added products and processes that will help move the marine energy industry forward. The PRIMRE team has recently launched two key initiatives in the U.S.—Signature Projects and Lessons Learned. Outputs and outcomes from these two initiatives will be highlighted in this paper. The Signature Projects initiative is intended to bring focus to a selection of ongoing and completed marine energy projects funded by the U.S. Department of Energy’s Water Power Technologies Office (WPTO), and to inform the marine energy community of what investigations have been undertaken, what tools are available, and where gaps in information persist. Each Signature Project tags papers, reports, and data from large marine energy research projects, providing easy access and attention to all the output and associated products from each project. The Lessons Learned initiative is intended to ensure that hard-won achievements are recognized and available for those who come later, that missteps and unfortunate outcomes can be prevented in future, and that efficiencies and effective shortcuts can be publicized and used as the marine energy industry moves forward. This initiative builds off the Knowledge Hubs and reaches out to members of the marine energy community, particularly technology developers and researchers, to integrate experience in the development, deployment, assessment, success, and challenges while creating this new industry and field of study.

Copping, Andrea E.↗

DOE OSTI2021

Added value for integrated marine energy data systems

Launched in 2019, the Portal and Repository for Information on Marine Renewable Energy (PRIMRE) provides centralized access, standardization, community building, and integration of United States (U.S.) databases, tools and codes, and other resources that cover a range of marine energy information. The PRIMRE universe contains a series of Knowledge Hubs that represent data and information on testing of marine energy devices (MHKDR); environmental effects (Tethys); engineering and technical papers (Tethys Engineering); descriptions of marine energy companies and technologies (Marine Energy Projects Database); codes and models (Marine Energy Software); and guidance on testing and measurements (Telesto). Content is added to PRIMRE by applying a set of Guidelines and Best Practices (PRIMRE Guidelines). An aggregate search across the PRIMRE site enables users to find data and information from all the PRIMRE Knowledge Hubs simultaneously, using a single entry-point (PRIMRE Search). In addition to providing access to a range of data and information on marine energy development, testing, and effects, PRIMRE allows for the development of value added products and processes that will help move the marine energy industry forward. The PRIMRE team has recently launched two key initiatives in the U.S.—Signature Projects and Lessons Learned. Outputs and outcomes from these two initiatives will be highlighted in this paper. The Signature Projects initiative is intended to bring focus to a selection of ongoing and completed marine energy projects funded by the U.S. Department of Energy’s Water Power Technologies Office (WPTO), and to inform the marine energy community of what investigations have been undertaken, what tools are available, and where gaps in information persist. Each Signature Project tags papers, reports, and data from large marine energy research projects, providing easy access and attention to all the output and associated products from each project. The Lessons Learned initiative is intended to ensure that hard-won achievements are recognized and available for those who come later, that missteps and unfortunate outcomes can be prevented in future, and that efficiencies and effective shortcuts can be publicized and used as the marine energy industry moves forward. This initiative builds off the Knowledge Hubs and reaches out to members of the marine energy community, particularly technology developers and researchers, to integrate experience in the development, deployment, assessment, success, and challenges while creating this new industry and field of study.

Copping, Andrea E.↗

DOE OSTI2021

Added Value for Integrated Marine Energy Data Systems (February 2021)

Launched in 2019, the Portal and Repository for Information on Marine Renewable Energy (PRIMRE) provides centralized access, standardization, community building, and integration of United States (U.S.) databases, tools and codes, and other resources that cover a range of marine energy information. The PRIMRE universe contains a series of Knowledge Hubs that represent data and information on testing of marine energy devices (MHKDR); environmental effects (Tethys); engineering and technical papers (Tethys Engineering); descriptions of marine energy companies and technologies (Marine Energy Projects Database); codes and models (Marine Energy Software); and guidance on testing and measurements (Telesto). Content is added to PRIMRE by applying a set of Guidelines and Best Practices (PRIMRE Guidelines). An aggregate search across the PRIMRE site enables users to find data and information from all the PRIMRE Knowledge Hubs simultaneously, using a single entry-point (PRIMRE Search). In addition to providing access to a range of data and information on marine energy development, testing, and effects, PRIMRE allows for the development of valueadded products and processes that will help move the marine energy industry forward. The PRIMRE team has recently launched two key initiatives in the U.S.-Signature Projects and Lessons Learned. Outputs and outcomes from these two initiatives will be highlighted in this paper. The Signature Projects initiative is intended to bring focus to a selection of ongoing and completed marine energy projects funded by the U.S. Department of Energy's Water Power Technologies Office (WPTO), and to inform the marine energy community of what investigations have been undertaken, what tools are available, and where gaps in information persist. Each Signature Project tags papers, reports, and data from large marine energy research projects, providing easy access and attention to all the output and associated products from each project. The Lessons Learned initiative is intended to ensure that hard-won achievements are recognized and available for those who come later, that missteps and unfortunate outcomes can be prevented in future, and that efficiencies and effective shortcuts can be publicized and used as the marine energy industry moves forward. This initiative builds off the Knowledge Hubs and reaches out to members of the marine energy community, particularly technology developers and researchers, to integrate experience in the development, deployment, assessment, success, challenges while creating this new industry and field of study.

data sharing↗

DOE OSTI2021

Historical Context and Perspective on Allowable Stresses and Design Parameters in ASME Section III, Division 5, Subsection HB, Subpart B

In the 1970s, the U.S. Nuclear Regulatory Commission (NRC) issued Regulatory Guide (RG) 1.87 (Rev 1, June 1975) to provide interim licensing guidelines to aid applicants in implementing the 10 CFR Part 50 requirements with respect to American Society of Mechanical Engineers (ASME) Boiler Pressure and Vessel Code (BPVC) Class 1 components operating at elevated temperatures for high-temperature gas-cooled reactors, liquid-metal fast-breeder reactors, and gas-cooled fast-breeder reactors. RG 1.87 referenced ASME Code Case 1592 for materials and design and Code Cases 1593, 1594, 1595, and 1596 for fabrication and installation, examination, testing, and overpressure protection, respectively.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2015

SU-E-P-43: A Knowledge Based Approach to Guidelines for Software Safety

Purpose: In the fall of 2012, a survey was distributed to medical physicists across Canada. The survey asked the respondents to comment on various aspects of software development and use in their clinic. The survey revealed that most centers employ locally produced (in-house) software of some kind. The respondents also indicated an interest in having software guidelines, but cautioned that the realities of cancer clinics include variations, that preclude a simple solution. Traditional guidelines typically involve periodically repeating a set of prescribed tests with defined tolerance limits. However, applying a similar formula to software is problematic since it assumes that the users have a perfect knowledge of how and when to apply the software and that if the software operates correctly under one set of conditions it will operate correctly under all conditions Methods: In the approach presented here the personnel involved with the software are included as an integral part of the system. Activities performed to improve the safety of the software are done with both software and people in mind. A learning oriented approach is taken, following the premise that the best approach to safety is increasing the understanding of those associated with the use or development of the software. Results: The software guidance document is organized by areas of knowledge related to use and development of software. The categories include: knowledge of the underlying algorithm and its limitations; knowledge of the operation of the software, such as input values, parameters, error messages, and interpretation of output; and knowledge of the environment for the software including both data and users. Conclusion: We propose a new approach to developing guidelines which is based on acquiring knowledge-rather than performing tests. The ultimate goal is to provide robust software guidelines which will be practical and effective.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2024

Antigua and Barbuda Distributed Energy Resources Deployment Guidelines

This document is designed to provide comprehensive considerations, best practices and guidance for deployment of Distributed Energy Resources (DERs) in Antigua and Barbuda. The document provides lists of various technology selection guidance including technical specifications, requirements and applicable key standards and code associated with key DERs and balance of plant equipment. The document also presents the key microgrid design considerations to integrate the DERs to achieve the economic, decarbonization and resiliency goals. Taking into account sensitive grid for such islands, for grid readiness and screening the potential DER interconnection, general approach is highlighted along with the potential technical interconnection requirements. Furthermore, this document shows the key stakeholders involved in such DER integration and/or microgrid project and how key responsible project team can be qualified. Finally, this document refers to key information about warranties and consumer rights and maintenance of the systems.

24 POWER TRANSMISSION AND DISTRIBUTION↗