Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COPPER 65”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

High Strength, Utilizable Ductility and Electrical Conductivity in Cold Rolled Sheets of Cu-Cr-Zr-Ti Alloy

The microstructure and properties of Cu-0.5Cr-0.03Zr-0.04Ti (wt.%) alloy subjected to cold rolling and aging were investigated using hardness and electrical conductivity measurement, tensile testing, and transmission electron microscopy. Plates subjected to 85% reduction in thickness showed significant improvement in the strength compared to solution treated and aged condition. By proper selection of aging temperature, ductility could be significantly improved without reduction in the strength. Aging of the cold rolled sheet at 420 °C for 1 h yielded an ultimate tensile strength and yield strength of 540 and 460 MPa, respectively. On the other hand, total and uniform elongation was 16 and 12%, respectively, with an electrical conductivity of 65 %IACS. The combination of properties achieved after cold rolling and aging is attributed to the higher dislocation density, ultrafine grains and nano-sized chromium precipitates.

36 MATERIALS SCIENCE↗

Microstructure evolution, grain morphology variation and mechanical property change of Cu-Sn intermetallic joints subjected to high-temperature aging

Highlights: • The δ-Cu{sub 41}Sn{sub 11} could be formed by reaction of 11Cu{sub 3}Sn + 9Cu → Cu{sub 41}Sn{sub 11} during aging above 350 °C. • The temperature effects on the growth rate and grain morphology of Cu{sub 41}Sn{sub 11} phase were found. • The Cu{sub 41}Sn{sub 11} joints with refined grains exhibited higher hardness and shear strength. • The Cu{sub 41}Sn{sub 11} joints exhibited a combination of transgranular and intergranular fracture during shear test. - Abstract: In this work, the aging treatment was carried out on full Cu{sub 3}Sn joints at different temperatures for various durations, the microstructure evolution, grain morphology variation and mechanical property change of joints were investigated. The temperature effects on the growth rate and grain morphology of Cu{sub 41}Sn{sub 11} phase were found: The complete transformation from Cu{sub 3}Sn phase to Cu{sub 41}Sn{sub 11} phase in joints needed 300 h at 400 °C, but 4 h at 500 °C. The Cu{sub 41}Sn{sub 11} phase formed at 400 °C consisted of columnar grains with an average width of 23.5 μm, while the Cu{sub 41}Sn{sub 11} phase formed at 500 °C consisted columnar grains with an average width of 8.5 μm. The average hardness and shear strength values of the Cu{sub 41}Sn{sub 11} joints formed at 400 °C were 432.5 HV and 62 MPa, while the joints formed at 500 °C exhibited higher hardness and shear strength (451.5 HV and 65 MPa). Besides, the Cu{sub 41}Sn{sub 11} joint was found to exhibit a combination of transgranular and intergranular fracture during shear test.

36 MATERIALS SCIENCE↗

Towards Synthesis, Characterization and Properties of Smart Material Based on Chitosan Using Mn-IV Itaconic Acid as a Novel Redox Pair

The precipitation technique of Mn-IV/itaconic acid redox pair was chosen for grafting meth acrylic acid onto chitosan. This was done to maximize the graft yield and minimize the homopolymer formation to lower extent in addition to prepare water soluble chitosan instead of non-eco friendly acid soluble one. Evidence of grafting was confirmed instrumentally by (FTIR, SEM, and TGA), titrimetrically using carboxyl content and gravimetrically using dry weight method. The mechanism of grafting and factors affected grafting reaction were studied in details, and the optimum reaction conditions were obtained at [chitosan] 2 g, [MnO{sub 2}] 25.9 mmol/100 g sample, [itaconic acid],100 mmol/L, [MAA] 50% bows,[liquor ratio], 25, reaction time, 2 h, and [reaction temperature], 65 °C. It is also seen from the obtained results that, the resultant copolymer showed the following findings: (a) only nitric acid solutions are proved to be a superior solvent for the grafted product; (b) superabsorbent towards water (197 g H{sub 2}O/g polymer) and saline absorbency (60 g saline solution/g polymer) after cross-linked with epichlorohydrin, (c) higher water solubility (21%) at 48% graft yield and (d) 73.5% copper ion removal in comparison with 41% for chitosan.

36 MATERIALS SCIENCE↗

A model for high temperature deformation of nanolaminate Cu-Nb composites

Nanolaminate composites with layer thicknesses down to 65 nm display conventional 3 stage creep behavior with creep resistance increasing as layer thickness decreases. A model for the time dependent high temperature deformation response of Cu-Nb composites is developed, and compared to creep tests performed on multilayers fabricated via accumulative roll bonding (ARB). The model assumes a continuous laminate structure of 50 % Cu and 50 % Nb in which deformation is controlled by stage II creep for the copper (ε cr = Aσ n ) and plasticity in Nb. Regimes in which composite steady-state creep at constant stress can be achieved are identified. The modeling illustrates that strain-hardening in the niobium plays a critical role in the transient response of the multilayer, which can dominate the creep lifetime. The combination of experiments and models strongly suggest that dislocation climb mechanisms in the copper control the time-response at 400 °C for all layer thicknesses tested.

36 MATERIALS SCIENCE↗

Evaluating the Field Emission Characteristics of Aluminum for DC High Voltage Photo-Electron Guns

High current photoguns require high power laser light, but only a small portion of the laser light illuminating the photocathode produces electron beam. Most of the laser light (? 65\%) simply serves to heat the photocathode, which leads to evaporation of the chemicals required to create the negative electron affinity condition necessary for photoemission. Photocathode cooling techniques have been employed to address this problem, but active cooling of the photocathode is complicated because the cooling apparatus must float at high voltage. This work evaluates the field emission characteristics of cathode electrodes manufactured from materials with high thermal conductivity: aluminum and copper. These electrodes could serve as effective heat sinks, to passively cool the photocathode that resides within such a structure. However, literature suggests ``soft'' materials like aluminum and copper are ill suited for photogun applications, due to excessive field emission when biased at high voltage. This work provides an evaluation of aluminum and copper electrodes inside a high voltage field emission test stand, before and after coating with titanium nitride (TiN), a coating that enhances surface hardness.

Taus, Rhys↗

Measurement of internal dark current in a 17 GHz, high gradient accelerator structure

We report the measurement of the internal dark current in a 17 GHz, high gradient accelerator cavity and its comparison with theory. The cavities were fabricated from copper and had a sidewall that was either uncoated or coated with diamondlike carbon or TiN. The dark current was monitored by a downstream detector and by detectors behind two small slits made in the cavity sidewall. With an increasing gradient, the downstream current increased monotonically, as expected for field emission. The variation of the internal, side dark current was not monotonic but showed the onset of peaks at gradients near 45 and 65 MV / m . These were identified as the N = 2 and N = 1 single point multipactor resonances. The total internal dark current was estimated at ~ 15 – 30 A . The magnitude of the internal dark current and its dependence on the gradient were in good agreement with simulations using the cst code as well as an in-house code. Processing to a higher gradient, ~ 90 MV / m , eliminated the N = 2 mode, but the N = 1 mode persisted. The coated sidewall cavities showed the same multipactor resonances as the uncoated structure. However, at the highest gradient achieved in testing, the coated structures showed a modest reduction in the internal dark current.

43 PARTICLE ACCELERATORS↗

Laboratory micro- and nanoscale X-ray tomographic investigation of Al–7 at.%Cu solidification structures

X-ray computed tomography across multiple length scales provides an opportunity to non-destructively visualize and quantify the micro- to nano-scale microstructural features of solidification structures in three dimensions. Aluminum–7 at.%copper samples were directionally solidified at three cooling rates (0.44, 0.67, and 1.33 °C/s), resulting in systematic changes in the as-solidified microstructure, which are difficult to quantify using traditional microscopic techniques. The cooling rate of a material affects its ultimate microstructure, and characterizing that microstructure is key to predicting and understanding its bulk properties. Here, two different laboratory X-ray computed tomography instruments were used to characterize as-solidified microstructures, including micro-scale computed tomography with approximately 1 mm field-of-view, ∼ 1.7 μm resolution, and nano-scale X-ray computed tomography ∼ 65 μm FOV, 150 nm resolution. Micro-scale X-ray radiography and computed tomography enabled a quantitative investigation of changes in the primary dendritic solidification structure with increasing cooling rate. Nano-scale absorption contrast X-ray computed tomography resolved the distinct phases of the lamellar eutectic structure and three dimensional measurements of the ∼ 1 μm interlamellar spacing. It is found that the lamella eutectic structure thickness is inversely proportional to the cooling rate. Nano-scale Zernike phase contrast was also used to image voids at eutectic colony boundaries. The application and resolution of these two instruments are discussed with respect to the resolvable features of the solidification structures. - Highlights: • Al–Cu eutectic is a model system for studying solidification microstructure. • X-ray computed tomography provides a 3D picture of these complex structures. • Micro-scale tomography images the primary and secondary dendritic structures. • Nano-scale tomography images the eutectic lamella and measures its thickness. • The ∼ 1 micrometer thickness of the eutectic lamella correlates to the cooling rate.

36 MATERIALS SCIENCE↗

Measurement of internal dark current in a 17 GHz, high gradient accelerator structure

We report the measurement of the internal dark current in a 17 GHz, high gradient accelerator cavity and its comparison with theory. The cavities were fabricated from copper and had a sidewall that was either uncoated or coated with diamond-like carbon or TiN. The dark current was monitored by a downstream detector and by detectors behind two small slits made in the cavity side wall. With an increasing gradient, the downstream current increased monotonically, as expected for field emission. The variation of the internal, side dark current was not monotonic but showed the onset of peaks at gradients near 45 and 65 MV/m. These were identified as the N = 2 and N = 1 single point multipactor resonances. The total internal dark current was estimated at ∼15–30 A. The magnitude of the internal dark current and its dependence on the gradient were in good agreement with simulations using the CST code as well as an in-house code. Processing to a higher gradient, ∼90 MV/m, eliminated the N = 2 mode, but the N = 1 mode persisted. The coated sidewall cavities showed the same multipactor resonances as the uncoated structure. However, at the highest gradient achieved in testing, the coated structures showed a modest reduction in the internal dark current.

43 PARTICLE ACCELERATORS↗

Effect of Yb Substitution on Microstructure and Superconducting Properties of Y{sub 1−x}Yb{sub x}Ba{sub 2}Cu{sub 3}O{sub 7−δ} Films

The purpose of this study was to improve the critical current density (J{sub c}) of YBa{sub 2}Cu{sub 3}O{sub 7−δ} (YBCO) superconducting films at high magnetic fields. Thin Y{sub 1−x}Yb{sub x}Ba{sub 2}Cu{sub 3}O{sub 7−δ} (Y{sub 1−x}Yb{sub x}BCO) superconducting films on LaAlO{sub 3} substrates were prepared by modified low-fluorine metal organic deposition method (LF-MOD) in order to investigate the effect of Yb substitution on the microstructure and superconducting properties of a YBCO-coated conductor. In this study, single-phased, c-axial-aligned Y{sub 1−x}Yb{sub x}BCO films were obtained. Yb doping had a little effect on the critical temperature (T{sub c}) and transition width (ΔT) values of Y{sub 1−x}Yb{sub x}BCO films. An abnormal phenomenon was observed that the J{sub c} of Y{sub 1−x}Yb{sub x}BCO films at low field was smaller than that of the pure YBCO film, but the J{sub c} of Y{sub 1−x}Yb{sub x}BCO films at high field was much greater than that of the undoped YBCO film. Compared to pure YBCO film, the J{sub c} values of Y{sub 0.75}Yb{sub 0.25}BCO and Y{sub 0.25}Yb{sub 0.75}BCO films were enhanced by a factor of 8 at 8 T, 65 K, which meant that chemical substitution of Yb into the Y site could improve flux pinning significantly under the high magnetic field in Y{sub 1−x}Yb{sub x}BCO coated conductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Catalyst synthesis under CO 2 electroreduction favours faceting and promotes renewable fuels electrosynthesis

The electrosynthesis of C 2+ hydrocarbons from CO 2 has garnered recent attention in light of the relatively high market price per unit energy input. Today’s low selectivities and stabilities towards C 2+ products at high current densities curtail system energy efficiency, which limits their prospects for economic competitiveness. Here we present a materials processing strategy based on in situ electrodeposition of copper under CO 2 reduction conditions that preferentially expose and maintain Cu(100) facets, which favour the formation of C 2+ products. We observe capping of facets during catalyst synthesis and achieve control over faceting to obtain a 70% increase in the ratio of Cu(100) facets to total facet area. We report a 90% Faradaic efficiency for C 2+ products at a partial current density of 520 mA cm –2 and a full-cell C 2+ power conversion efficiency of 37%. We achieve nearly constant C2H4 selectivity over 65 h operation at 350 mA cm –2 in a membrane electrode assembly electrolyser.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of the LTC catalyst: Performance against common air pollutants

One of the important qualities of the Low-Temperature Catalyst (LTC) is the rapid oxidation of carbon monoxide to carbon dioxide under a wide variety of conditions. The catalytic material is a palladium-copper activated complex which reacts with various contaminant molecules through a continuous oxidation/reduction cycle. The alumina substrate enhances LTC activity with its favorable surface chemistry and very high surface area. About 10 percent surface water is necessary to facilitate the oxidation of CO. This reaction shows a log-log dependence on contact time, suggesting a Langmuir-Hinshelwood mechanism. In the tube tests, LTC removed 90 to 100 percent of contaminating carbon monoxide in the temperature region of 20 to 4000 C, and at ambient over a range of 25 to 65 percent relative humidity. In contrast, NO2 is chemisorbed by the LTC/alumina material--the amount strongly dependent on temperature increases but independent of humidity. The LTC catalyst has demonstrated excellent capability to remove an important variety of hazardous pollutant gases which are common factors to poor indoor air quality. The Instapure Air Filtration System incorporates the LTC catalyst in a 50:50 mixture with activated carbon to effectively remove particulate, odors, and hazardous gases at room temperature and humidities. The ability to remove hazardous gases is unique for the category of portable air filtration equipment. The wide variety of pollutant gases that LTC removes suggests that catalytic technology is adaptable to a considerable range of commercial and industrial applications.

Collins, Marcia F.↗

Crystallization kinetics of Mg–Cu–Yb–Ca–Ag metallic glasses

The paper presents research into a Mg–Cu–Yb system based metallic glassy alloys. Metallic glasses were prepared using induction melting and further injection on a spinning copper wheel. The effect of alloying by Ag and Ca on the glass forming ability and the kinetics of crystallization of Mg–Cu–Yb system based alloys were studied. The differential scanning calorimeter and X-ray diffractometer were used to investigate the kinetics of crystallization and the phase composition of the samples. An indicator of glass forming ability, effective activation energy of crystallization, and enthalpy of mixing were calculated. An increase of the Ca and Ag content has a positive effect on the glass forming ability, the effective activation energy of crystallization, and the enthalpy of mixing. The highest indicators of the glass forming ability and the thermal stability were found for alloys that contain both alloying elements. The Ag addition suppresses precipitation of the Mg{sub 2}Cu phase during crystallization. A dual-phase glassy-nanocrystalline Mg structure was obtained in Mg{sub 65}Cu{sub 25}Yb{sub 10} and Mg{sub 59.5}Cu{sub 22.9}Yb{sub 11}Ag{sub 6.6} alloys after annealing. Bulk samples with a composite glassy-crystalline structure were obtained in Mg{sub 59.5}Cu{sub 22.9}Yb{sub 11}Ag{sub 6.6} and Mg{sub 64}Cu{sub 21}Yb{sub 9.5}Ag{sub 5.5} alloys. A thermodynamic database for the Mg–Cu–Yb–Ca–Ag system was created to compare the process of crystallization of alloys with polythermal sections of the Mg–Cu–Yb–Ca–Ag phase diagram. - Highlights: • New alloy compositions based on Mg–Cu–Yb system were developed and investigated. • Increasing content of Ag and Ca leads to improving GFA. • Bulk samples with a composite glassy-crystalline structure were obtained. • Thermodynamic database for Mg–Cu–Yb–Ca–Ag system was created.

36 MATERIALS SCIENCE↗

Shock initiation of low density polymer bonded explosive LX-14: A study of two morphologies

A series of six shock initiation experiments have been carried out on low density LX-14 powder in order to simulate a shock insult on the heavily damage polymer bonded explosive, LX-14. Two distinct morphologies were studied (tap density molding powder and machined swarf), both at the same density of 0.942 g/cm 3 , or 50.1% theoretical maximum density. The purpose of these experiments was to provide data to help make an assessment of the effects that damage has on the material sensitivity to a planar shock. This was achieved primarily by providing shock sensitivity data in the form of a Pop plot, and also reactants equation of state data, which aids in the determination of input conditions for both the experiments performed in this work and also future experiments of this material type. The experiments were of a cut-back format, consisting of four sample heights on each shot and diagnosed with optical velocimetry. The experiments were carried out at the Technical Area 40 Chamber 9 gas gun facility at the Los Alamos National Laboratory, where the LX-14 targets were subjected to Al 6061 and Oxygen Free High Conductivity copper impactors launched to velocities up to 2.14 km/s. Time corrected reactive growth wave profiles are presented in this paper along with the derivation of the following Hugoniot parameters for this explosive, where the molding powder and machine swarf are represented by the following linear equations, respectively, U s = 1.64 (±0.64)u p + 2.25 (±0.49) and U s = 0.87 (±.0.60)u p + 4.08 (±0.49). The results show that the steady increase in shock sensitivity with increasing void fraction reaches an inflection point beyond which the shock sensitivity begins to decease. This inflection point lies between 65% and 50% of the theoretical maximum density of the LX-14. In both cases, the damaged LX-14 was not as sensitive as expected, with a relative shock sensitivity of the molding powder being less than the pressed LX-14, and the machined swarf having a shock sensitivity that is comparable to pressed LX-14.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Study of Cu-Ni-Fe Alloys as Inert Anodes for Al Production in Low-Temperature KF-AlF{sub 3} Electrolyte

Cu-Ni-Fe-based alloys are considered as promising O{sub 2}-evolving anode materials for CO{sub 2}-free Al production. In the present study, biphased (as-cast) and monophased (postcasting homogenized) Cu{sub 65}Ni{sub 20}Fe{sub 15}, alloys, and monophased Ni{sub 65}Fe{sub 25}Cu{sub 10} alloy (in wt pct) are evaluated as O{sub 2}-evolving anodes for Al production in potassium cryolite at 700 °C. The produced Al purity is 99.6 wt pct, and the erosion rate is estimated at 0.4 cm year{sup −1} for both Cu{sub 65}Ni{sub 20}Fe{sub 15} anodes compared to 95.2 wt pct and 3.2 cm year{sup −1} for the Ni{sub 65}Fe{sub 25}Cu{sub 10} anode. The compositions, and morphologies of the surface oxide layer and the metal fluoride layer present at the oxide/alloy interface are compared for the three anodes. The deleterious impact of electrolyte infiltration on the surface oxide building is highlighted.

36 MATERIALS SCIENCE↗

High Compression‐Induced Conductivity in a Layered Cu–Br Perovskite

Abstract We show that the onset pressure for appreciable conductivity in layered copper‐halide perovskites can decrease by ca. 50 GPa upon replacement of Cl with Br. Layered Cu–Cl perovskites require pressures >50 GPa to show a conductivity of 10 −4 S cm −1 , whereas here a Cu–Br congener, (EA) 2 CuBr 4 (EA=ethylammonium), exhibits conductivity as high as 2×10 −3 S cm −1 at only 2.6 GPa, and 0.17 S cm −1 at 59 GPa. Substitution of higher‐energy Br 4p for Cl 3p orbitals lowers the charge‐transfer band gap of the perovskite by 0.9 eV. This 1.7 eV band gap decreases to 0.3 eV at 65 GPa. High‐pressure X‐ray diffraction, optical absorption, and transport measurements, and density functional theory calculations allow us to track compression‐induced structural and electronic changes. The notable enhancement of the Br perovskite's electronic response to pressure may be attributed to more diffuse Br valence orbitals relative to Cl orbitals. This work brings the compression‐induced conductivity of Cu‐halide perovskites to more technologically accessible pressures.

Jaffe, Adam↗

Life Cycle Assessment of Future Photovoltaic Electricity Production from Residential-scale Systems Operated in Europe

The photovoltaics (PV) industry is growing rapidly to meet the increasing demand of green power. As the industry grows, the manufacturing processes and the material and energy efficiencies of PV cells and panels are improving. To assess the impacts of this trend, future scenarios of single-crystalline (single-Si, also known as mono-crystalline) silicon and cadmium-telluride (CdTe) PV systems installed on European residences were established. Assessment of the improvement potential of PV electricity-generating technologies such as single-Si and CdTe could be considered in long-term energy strategy decisions. This study aims to provide scenario-based information about the environmental per-formance of single-Si and CdTe PV modules produced and operated in the far future (2030 to 2050). The deployment application assessed considers European residential roofs. We made scenario-dependent projections of key parameters for single-Si and CdTe PV panels manufactured in 2050. The parameters included cell efficiency, module efficiency, wafer thickness, cutting losses, kerf losses, silver use, glass thickness and operational lifetime. This study combines developments for these parameters with projections of the environmental performance of electricity mixes in the main manufacturing countries/regions (European Union, China and the United States of America) and with projections of the environ-mental performance of basic material production (aluminium, copper, magnesium, nickel, pig iron, zinc, clinker and flat glass) in the far future. The three scenarios used in the assessment of future PV electricity were categorized into three classes: 'business as usual' (BAU), 'realistic improvement' (REAL) and 'optimistic improvement' (OPT). It estimates the current life cycle greenhouse gas emissions of single-Si PV electricity produced on the roofs of European residences to be approximately 80 grams CO2-equi-valent per kWh (g CO2-eq per kWh). Based on the projected changes to key parameters and the background system, life cycle greenhouse gas (GHG) emissions could be reduced to 65% (scenario BAU), 31% (scenario REAL) and 18% (scenario OPT) of that value in the far future. Results for other life cycle assessment (LCA) metrics are also assessed in this study such as: non-renewable cumulative energy demand, acidification potential, human toxicity potential, photochemical ozone creation potential, particulate matter formation potential, and land use. We calculated the total energy payback time (EPBT) and the non-renewable energy payback time (NREPBT) in the far future of single-crystalline silicon-based PV panels operated in Europe by dividing the estimate of non-renewable cumulative energy demand of PV electricity for the given scenario by the non-renewable cumulative energy demand of the scenario-dependent national and regional non-renewable residual electricity mixes. The study estimates the payback time could be reduced from 2.4 years today to 1.7, 1.2 and 1.2 years (scenarios BAU, REAL and OPT, respectively) in the far future, based on the assumptions and projections in the analysis. It finally estimates the current life cycle greenhouse gas emissions of CdTe PV electricity produced on the roofs of European residences to be approximately 30 g CO2-eq per kWh. Based on the projected changes to key parameters and the background system, life cycle GHG emissions could be reduced to 70% (scenario BAU), 44% (scenario REAL) and 32% (scenario OPT) of that value in the far future.

14 SOLAR ENERGY↗

Transparent conductive and near-infrared reflective Ga-doped ZnO/Cu bilayer films grown at room temperature

Bilayer films consisting of Ga-doped ZnO (GZO) and Cu layers were grown at room temperature by magnetron sputtering. The structural, electrical, and optical properties of GZO/Cu bilayer films were investigated in detail. The crystallinity and transparent-conductive properties of the films were correlated with the Cu layer thickness. The GZO/Cu bilayer film with the Cu layer thickness of 7.8 nm exhibited a low resistivity of 7.6x10{sup -5} {Omega} cm and an average visible transmittance of 74%. The reflectance was up to 65% in the near-infrared region for this film. The transparent conductive and near-infrared reflective GZO/Cu bilayer films could be readily deposited at room temperature. The GZO/Cu bilayer films were thermally stable when annealed at temperatures as high as 500 deg. C.

36 MATERIALS SCIENCE↗

Updates to the n+ 63,65 Cu Angular Distributions [Slides]

The performance of the benchmark suite is very sensitive to changes in the angular distribution data. The quasi-differential measurements performed by Blain et al at RPI provide a valuable constraint. Furthermore, ENDF/B-VIII.0 disagrees with their measurements consistently at 300 keV (the transition between RRR and high energy). The next step is to conservatively adjust the Legendre coefficients near 300 keV, validating performance against both critical benchmarks and the RPI quasi-differential measurements.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗