Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSION LOADING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Instability of fiber-reinforced viscoelastic composite plates to in-plane compressive loads

This study analyzes the stability behavior of unidirectional fiber-reinforced composite plates with viscoelastic material behavior subject to in-plane biaxial compressive edge loads. To predict the effective time-dependent material properties, elastic fibers embedded in a linearly viscoelastic matrix are examined. The micromechanical relations developed for a transversely isotropic medium are discussed along with the correspondence principle of linear viscoelasticity. It is concluded that the stability boundary obtained for a viscoelastic plate is lower (more critical) than its elastic counterpart, and the transverse shear deformation effects are more pronounced in viscoelastic plates than in their elastic counterparts.

Chandiramani, N. K.↗
NASA NTRS1980

Failure prediction techniques for compression loaded composite laminates with holes

The degree of notch sensitivity of composites in compression and whether their failures can be predicted over a wide range of plate and hole sizes. The notch sensitivity of composites is investigated by comparing actual failure loads of laminates with circular holes, with the extreme failure that would be expected from an ideal notch insensitive material and from an ideal notch sensitive material. The predictability question is addressed by applying the point stress failure criterion to a wide range of plate widths and hole sizes and comparing with available experimental data. The severity of impact is explored by comparing strength reductions resulting from impact with those resulting from comparable size circular holes. Finally, comparison is made of the differences to be expected from the effects of cracks and circular holes on failure strength.

Mikulas, M. M., Jr.↗
NASA NTRS2016

Compressive Loading and Modeling of Stitched Composite Stiffeners

A series of single-frame and single-stringer compression tests were conducted at NASA Langley Research Center on specimens harvested from a large panel built using the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept. Different frame and stringer designs were used in fabrication of the PRSEUS panel. In this paper, the details of the experimental testing of single-frame and single-stringer compression specimens are presented, as well as discussions on the performance of the various structural configurations included in the panel. Nonlinear finite element models were developed to further understand the failure processes observed during the experimental campaign.

Leone, Frank A., Jr.↗
NASA NTRS1940

An Investigation of Sheet-stiffener Panels Subjected to Compression Loads with Particular Reference to Torsionally Weak Stiffeners

A total of 183 panel specimens of 24ST aluminum alloy with nominal thickness of 0.020, and 0.040 inch with extruded bulb-angle sections of 12 shapes spaced 4 and 5 inches as stiffeners were tested to obtain the buckling stress and the amplitude of the maximum wave when buckled. Bulb angles from 3 to 27 1/2 inches long were tested as pin-end columns. The experimental data are presented as stress-strain and column curves and in tabular form. Some comparisons with theoretical results are presented. Analytical methods are developed that make it possible for the designer to predict with reasonable accuracy the buckling stress and the maximum-wave amplitude of the sheet in stiffened-panel combinations. The scope of the tests was insufficient to formulate general design criteria but the results are presented as a guide for design and an indication of the type of theoretical and experimental work that is needed.

LOADS - COLUMNS↗
NASA NTRSDate not supplied

Progressive Damage Analysis of Post-Buckled Stiffened Panels under Static Compressive Loading

The validation of progressive damage analysis methods requires experimental data that captures the initiation of damage, its evolution with continued loading, and the morphology of damage throughout its evolution. In support of the NASA Advanced Composites Project, several validation specimens of increasing complexity have been tested and characterized in order to provide the data required to assess the capabilities of several progressive damage analysis methods for fiber-reinforced composite materials. The analytical capabilities of interest for this validation program include networks of interacting matrix cracks and delaminations in post-buckled stiffened structures. A series of single stringer compression specimens was tested and characterized at NASA Langley Research Center. The experimental data from these tests are compared with progressive damage finite element analysis results. Test/analysis comparisons are made in terms of load/displacement histories, damage morphology, and damage size versus load metrics.

Frank A Leone↗
NASA NTRS1983

Fixture for environmental exposure of structural materials under compression load

A device for stressing a deformable material specimen consists of top plate and a bottom plate sandwiching a guide cylinder. The specimen is positioned on the bottom plate and attached to a load piston. Force is applied through the top plate into the guide cylinder. Once the specimen is loaded, the stress is maintained by tightening tie bolt nuts.

Clark, R. K.↗
NASA NTRS1984

Opening of an interface flaw in a layered elastic half-plane under compressive loading

A static analysis is given of the problem of an elastic layer perfectly bonded, except for a frictionless interface crack, to a dissimilar elastic half-plane. The free surface of the layer is loaded by a finite pressure distribution directly over the crack. The problem is formulated using the two dimensional linear elasticity equations. Using Fourier transforms, the governing equations are converted to a pair of coupled singular integral equations. The integral equations are reduced to a set of simultaneous algebraic equations by expanding the unknown functions in a series of Jacobi polynomials and then evaluating the singular Cauchy-type integrals. The resulting equations are found to be ill-conditioned and, consequently, are solved in the least-squares sense. Results from the analysis show that, under a normal pressure distribution on the free surface of the layer and depending on the combination of geometric and material parameters, the ends of the crack can open. The resulting stresses at the crack-tips are singular, implying that crack growth is possible. The extent of the opening and the crack-top stress intensity factors depend on the width of the pressure distribution zone, the layer thickness, and the relative material properties of the layer and half-plane.

Kennedy, J. M.↗
NASA NTRS1983

Buckling and vibration of any prismatic assembly of shear and compression loaded anisotropic plates with an arbitrary supporting structure

The computer program designated 'VIPASA', which accurately treats buckling and vibration in prismatic plate assemblies with a response that varies sinusoidally in the longitudinal direction, has been found to be limited by the production of an in-plane shear loading of component plates that produces skewed mode shapes. These do not conform to desired support conditions. This problem is presently overcome through a coupling of the VIPASA stiffness matrices for different wavelength responses by means of the Lagrangian Multipliers method. The theory extends to supports at arbitrary locations, and even to the support provided by any elastic structure. The generality and capabilities of VIPASA have been retained in the computer program designated 'VICON', which permits constraints and a supporting structure consisting of any number of transverse beam columns.

Anderson, M. S.↗
NASA NTRS1986

Buckling behavior of compression-loaded symmetrically-laminated angle-ply plates with holes

An approximate analysis for buckling of a rectangular specially-orthotropic plate with a central circular hole is applied to symmetrically-laminated angle-ply plates. Results obtained from finite element analyses and experiments indicate that the approximate analysis predicts accurately the buckling loads of (+/-theta sub m)s plates with integer values of m not below 6 and with hole diameters up to 50 percent of the plate width. Moreover, the results indicate that the approximate analysis can be used to predict the buckling trends of plates with hole diameters up to 70 percent of the plate width. Results of a parametric study indicate the influence of hole size, plate aspect ratio, loading conditions, boundary conditions, and orthotropy on the buckling load. Results are also presented that indicate the relationship of the bending stiffness and the prebuckling load distribution to the buckling load of a plate with a hole.

Nemeth, M. P.↗