Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CEMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Analysis of Carbon Capture Retrofits for Cement Plants

The objective of this study is to provide an estimate of the cost to capture CO 2 in retrofit applications at cement plants. The cement plant configurations considered in this study include natural gas and solid fuel (coal and coke) cases, and both wet- and dry kiln-fed plant designs, however the base cement plants in this study were not evaluated other than characterization of their kiln off-gas stream and high-level quantification of heat integration potential at the existing plant. In each case, the base cement plant produces 1.5 M tonnes per year of finished cement, assuming 91.4 percent clinker content. This analysis includes a 10 percent retrofit cost increase for process integration and low grade heat recovery, when compared to the analogous non-heat integration case. Heat integration is considered as a potential offset to capture system heating demands (i.e., as a percentage reduction). Recovery and reuse of excess heat from the base cement plant can provide economic benefits—primarily by reducing the need to purchase supplemental natural gas for CO 2 solvent regeneration—but any process improvement must be great enough to overcome the cost increases (i.e., capital and O&M) necessary to realize those benefits. With heat integration potential of 10 percent and 30 percent, that benefit wasn’t significant enough to offset the increase in capital and operating costs, and a cost of capture increase was observed based on the assumptions in this report. Benefits of heat integration potential may be realized when natural gas prices are higher, as demonstrated in the sensitivity to natural gas price where crossover points exist between heat integration cases and their respective non-heat integration cases. Four of the base cases were further evaluated to explore the cost implications of deeper levels of gas pre-treatment to remove oxides of nitrogen (NOx) and oxides of sulfur (SOx) from the kiln off-gas stream prior to CO 2 capture, purification, and compression. The results of these additional case analyses showed a 7.4–18.8 percent increase in cost of capture over the respective base case (i.e., analogous cases without SOx/NOx removal).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Self-re-adhering alkali-activated cement composite and its ability to mitigate corrosion of carbon steel in 300 °C hydrothermal environment

Cement-steel interface is a weak point of cement sheath integrity under the environments of high-temperature geothermal wells. This paper presents carbon steel (CS) adherence behaviors of 300 °C-autoclaved alkali-activated Calcium-Aluminate-Cement (CAC)/fly ash F (FAF) (Thermal Shock Resistant Cement, TSRC), granulated blast furnace slag (GBFS)/SiO 2 , and Ordinary Portland Cement (OPC)/SiO 2 blends. The composites’ ability to preserve the bond under the conditions of thermal shock (TS) and strong acid attack (pH 0.6 H 2 SO 4 /brine at 90 °C) as well as their ability to recover the damaged bond and provide steel corrosion protection after additional short-time 5-day curing at 300 °C were evaluated. GBFS/SiO 2 sheath underwent catastrophic failure in the first TS cycle; OPC/SiO 2 lost 78 % and TSRC 51 % of the bond strength in 6 cycles. Only TSRC-CS bond survived 30 days of strong acid exposure; OPC/SiO 2 bond failed after 18 days and GBFS/SiO 2 after 20 days. Addition of micro-glass fibers (MGF) to TSRC further improved its bond strength and CS corrosion protection. Samples of TSRC-CS cured for 30 days at 300 °C before the bond damage recovered 49 % of the damaged bond strength after additional short-time curing. The CS protected by the re-adhered TSRC showed low corrosion rate of 0.13 mm/year (TSRC-MGF), 0.2 mm/year (TSRC) vs. 0.64 mm/year for OPC/SiO 2 protected CS.

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Assessment the leaching characteristics and long-term leaching behavior of some radionuclides from synthesized zeolite cement matrix

Highlights: • Synthesis and characterization of zeolite cement synthesized from fly ash • Leaching tests were used to assess the release rate of {sup 85}Sr and {sup 60}Co radionuclides. • Simple mathematical models were used to detect leaching mechanisms. • Long-term leaching behavior of {sup 85}Sr and {sup 60}Co from cementitious matrix was assessed. The development of cementitious materials remains a vital goal to produce valuable products with good mechanical, physical and chemical properties suitable for the safe disposal of concentrated radionuclides resulted from the treatment of contaminated solutions. In this paper, zeolite cement with good properties was laboratory synthesized from industrial by-products fly ash and characterized using various characterization techniques. The leaching characteristics of strontium and cobalt radionuclides from the synthesized zeolite cement were scrutinized conforming with the standard leaching methodology of International Atomic Energy Authority (IAEA). A mechanical strength assessment was executed to characterize the extent of immobilization process of the solidified matrices. The cumulative leaching fraction (φ) of the two studied radionuclides was found to be less than 5% in all examined conditions, which implies the applicability of the IAEA-recommended methodology for estimating the diffusion coefficient. The experimental leaching data were regressed nonlinearly to various mathematical kinetic models to assess the controlling leaching mechanism and to determine the leaching parameters. The regression results indicated that strontium ({sup 85}Sr) and cobalt ({sup 60}Co) leaching resulted from two succeeding mechanisms: as first order kinetic reaction, and then diffusion. The calculated values of leachability indices signify that the performance of each of the studied matrices is within an acceptable range. A simplified mathematical model, rooted in the first order reaction and diffusion mechanisms, was simulated to predict the radionuclides leaching rates from zeolite cement matrices. By comparing the synthesized zeolite cement with other cementitious materials, it can be concluded that the synthesized material can be classified as an efficient material suitable to immobilize {sup 85}Sr and {sup 60}Co from radioactive wastes. The acquired findings demonstrated that the studied immobilized waste matrices have acceptable mechanical effectiveness.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of temperature curing on properties and hydration of wollastonite blended magnesium potassium phosphate cements

K-struvite, the main hydrate of magnesium potassium phosphate (MKP) cements, dehydrates at ~50 °C, thus elevated temperatures at service conditions could affect cement properties and durability. In this study, properties and hydration of MKP cement without and with wollastonite were investigated at 20 and 50 °C. In hydrated pure MKP cement K-struvite decomposes progressively over time to MgKPO{sub 4}·H{sub 2}O at 50 °C, which leads to a strong reduction of solid volume and severe strength loss. The presence of wollastonite significantly slows down the decomposition rate of K-struvite, which is still observed after 393 days at 50 °C. K-struvite together with amorphous hydroxyapatite, M-(C)-S-H and CaK{sub 3}H(PO{sub 4}){sub 2} from the wollastonite reaction result in a cement with good short and long-term strength at both 20 and 50 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of blended cements and carbonation on chloride-induced corrosion propagation

Highlights: • Corrosion propagation of blended cements was investigated for 1 year. • Carbonated and non‑carbonated mortars were evaluated. • Galvanostatic pulse and ER sensors were used to monitor corrosion. • Mortar properties were correlated with corrosion rates and corrosion damage. • Relationships between mortar properties and corrosion behaviour were established. Supplementary cementitious materials are known to refine the pore structure of concrete and accelerate the carbonation progress. The combination of the two processes can have both beneficial and disadvantageous effects on corrosion, especially when chlorides are also involved. In this study the corrosion properties of multiple blended cements were evaluated in carbonated and non‑carbonated states, with chlorides introduced through cyclic ponding. The examination involved monitoring the propagation phase, determining the microstructural properties of cements, and assessing the final corrosion damage. The results showed that the steel in the blended cements initially had a relatively high corrosion activity, which later decreased compared to the OPC. This stabilisation was presumably due to the beneficial changes to the pore structure. Carbonation had a significant impact on the corrosion, with carbonated mortars revealing shallower damage over a larger surface area. This effect was more pronounced for blended cements that exhibited greater susceptibility to carbonation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Characterization of reactive MgO-modified calcium sulfoaluminate cements upon carbonation

This study characterizes reactive MgO-modified calcium sulfoaluminate (CSA) cement upon carbonation. Paste samples were fabricated by replacing CSA cement with reactive MgO at levels of 0, 5, 10, and 20 wt%. The samples were cured for 56 days and further cured at a CO{sub 2} concentration of 3% for 28 days. MgO incorporation into the CSA cement favored the formation of monosulfate over ettringite. Externally supplied MgO in the CSA cement reduced Al uptake in C-A-S-H and formed hydrotalcite as a secondary phase, which is associated with a reduction in the carbonation degree. In addition, the incorporated MgO inhibited the carbonation of ettringite and monosulfate, while more C-A-S-H and aluminum hydroxide were formed in neat CSA cement upon carbonation, showing the nearly full decomposition of ettringite and monosulfate. The tetrahedral Al network of the MgO-modified sample was not altered upon carbonation, indicating that MgO modified the route of carbonation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Impact of downhole pressure and fluid-access on the effectiveness of wellbore cement expansion additives

Autogenous shrinkage of wellbore cement widely impairs zonal isolation. MgO-based cement expansion additives (CEAs) can mitigate this shrinkage, or even impart net expansion, by creating porosity through displacive crystal growth-processes. However, both MgO hydration and autogenous shrinkage behaviour depend strongly on stress state. Evaluation of CEA performance in wellbore cements therefore requires testing under elevated pressures representative for subsurface environments. We report experiments addressing the chemical and bulk volume changes that occur in cement hydrating at 10 MPa confining pressure and 90 °C. Volumetric response was investigated as function of MgO concentration, external water supply, and pore pressure decrease through water consumption during reaction. Results show the bulk expansion achieved using MgO-based CEAs diminishes markedly with increasing effective confining pressure or, equivalently, upon restricting fluid supply. This reduced expansion-potential under pressure has profound implications for slurry design, notably regarding CEA-concentrations required to counteract micro-annulus formation while maintaining low cement permeability.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Near-field infrared microscopy: A novel analytic mapping technique to nanocharacterize calcium silicate-based cement materials

Infrared imaging via scattering-type scanning near-field optical microscopy (s-SNOM) allows chemical mapping of organic and inorganic materials with nanoscale spatial resolution. However, its potential adaptation to the complex multiphase structure of Portland cement is yet to be explored. Here we demonstrate the successful implementation of s-SNOM to spatially resolve coexisting chemical phases in tricalcium silicate, Portland cement's main compound, with 20-nm resolution. We found that s-SNOM is sensitive to different anhydrous polymorphic phases, revealing nanoscale domains that are ‘invisible’ to other microscopic techniques. Furthermore, s-SNOM's ability to distinguish the unhydrated and hydrated phases signifies its great promise as an analytical tool to study the complex hydration process of cement. The key to s-SNOM's application was nano-modifying the surface roughness of the cement samples, allowing nanoscale infrared imaging without topographical artifacts. Our study opens a window for infrared spectral microscopy in cement and other porous inorganic materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Modeling the corrosion of steel casing and the damage of well cement in a borehole system

This work presents the effect of chloride-induced corrosion in an underground borehole system, specifically considering the steel casing and further damage to the surrounding cement. In the past four decades, oil well cement has been successfully used for underground construction. However, high concentrations of chloride ions gradually degrade the functionality and durability of well cement. Gasses and liquids can leak from deterioration caused by chloride ions, and thus motivate this study. The chemo-mechanical coupling diffusion model and a classical fracture mechanics model are applied. The model is validated with OPC concrete corrosion data from literature, and then applied to well cement using experimentally obtained material property data. The time when crack initiation, peak pressure, and complete fracture is reached in the model of the cement sheath provides a quantification of the expected service life of the borehole system.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Wellbore cement fracture permeability as a function of confining stress and pore pressure

Cemented annulus fractures are a major leakage path in a wellbore system, and their permeability plays an important role in the behavior of fluid flow through a leaky wellbore. The permeability of these fractures is affected by changing conditions including the external stresses acting on the fracture and the fluid pressure within the fracture. Laboratory gas flow experiments were conducted in a triaxial cell to evaluate the permeability of a wellbore cement fracture under a wide range of confining stress and pore pressure conditions. For the first time, an effective stress law that considers the simultaneous effect of confining stress and pore pressure was defined for the wellbore cement fracture permeability. Here the results showed that the effective stress coefficient (λ) for permeability increased linearly with the Terzaghi effective stress ( -p) with an average of λ = 1 in the range of applied pressures. The relationship between the effective stress and fracture permeability was examined using two physical-based models widely used for rock fractures. The results from the experimental work were incorporated into numerical simulations to estimate the impact of effective stress on the interpreted hydraulic aperture and leakage behavior through a fractured annular cement. Accounting for effective stress-dependent permeability through the wellbore length significantly increased the leakage rate at the wellhead compared with the assumption of a constant cemented annulus permeability.

58 GEOSCIENCES↗
DOE OSTI2021

A comprehensive review on the loss of wellbore integrity due to cement failure and available remedial methods

With the recent abrupt fluctuations in oil pricing and the need of complying with environmental and social requirements, nowadays it is an urgent call for the oil and gas industry to produce the hydrocarbon without any loss as well as in a safe manner. Cements are placed in the annular space of casing to provide zonal isolation in between wellbore and surface during the operational life cycle of the well or even after the abandonment. But this is not what happens most of the time. Cement degrades or loses its integrity through debonding either from the casing or formation and generates cracks or fractures due to varied reasons throughout the life of the well. Multiple causes contribute to the loss of wellbore integrity – either by physical, mechanical, or chemical processes. These failures lead to sustained casing pressure (SCP) and contamination of surrounding environment. To combat this issue or to restore the well integrity, multiple remedial actions have also been either implemented in the industry or proposed based on experimental research to prevent the damage or to seal the leakage in the cement sheath. Here, this paper will provide an extensive review of the underlying reasons of cement failure and the available remedial actions to minimize the loss of well integrity issue. These information are not only useful to know about the different corrective options available for us to implement in industry but also it will provide us a knowledge base regarding how we can enhance the performance of the exiting systems to battle the cement integrity problem more efficiently.

02 PETROLEUM↗
DOE OSTI2026

Air Emissions Impacts of Fuel Substitution in the United States Cement Industry

High-heat industrial processes cannot be easily electrified, often rely on comparatively high-emitting solid fuels, and are essential for economic growth. Cement production in particular is critical to supporting construction and the expansion and maintenance of infrastructure systems in countries around the world. Fuels for cement production include petcoke, coal, and waste solvents, and their combustion contributes approximately 40% of the CO 2 emissions from global cement production. Broadening the fuel resources to include agricultural residues and other wastes can reduce emissions and divert waste from landfills. We assess the potential to use 16 different alternative fuels across the 88 integrated cement plants in the United States. The share of alternative fuels in the cement production sector could increase from the current level of 17% to as high as 73%. Fuel substitution can reduce the current fuel-related life-cycle emissions (28.6 ± 5.7 Mton CO 2 /year) by 19–45%. The greatest national-scale human health cobenefits occur when alternative fuels are prioritized at facilities currently using coal and petcoke. NO x emissions outcomes from this strategy are mixed, but SO x and particulate matter emissions reductions drive net human health benefits. These results suggest that targeted fuel substitution in heavy industries can yield outsized emissions benefits.

alternative fuels↗
DOE OSTI2024

ZeroCAL: Eliminating Carbon Dioxide Emissions from Limestone’s Decomposition to Decarbonize Cement Production

Limestone (calcite, CaCO 3 ) is an abundant and cost-effective source of calcium oxide (CaO) for cement and lime production. However, the thermochemical decomposition of limestone (~800 °C, 1 bar) to produce lime (CaO) results in substantial carbon dioxide (CO 2(g) ) emissions and energy use, i.e., ~1 tonne [t] of CO 2 and ~1.4 MWh per t of CaO produced. Here, we describe a new pathway to use CaCO 3 as a Ca source to make hydrated lime (portlandite, Ca(OH) 2 ) at ambient conditions (p, T) while nearly eliminating process CO 2(g) emissions (as low as 1.5 mol. % of the CO 2 in the precursor CaCO 3 , equivalent to 9 kg of CO 2(g) per t of Ca(OH) 2 ) within an aqueous flowelectrolysis/ pH-swing process that coproduces hydrogen (H 2(g) ) and oxygen (O 2(g) ). Because Ca(OH) 2 is a zero-carbon precursor for cement and lime production, this approach represents a significant advancement in the production of zero-carbon cement. The Zero CArbon Lime (ZeroCAL) process includes dissolution, separation/recovery, and electrolysis stages according to the following steps: (Step 1) chelator (e.g., ethylenediaminetetraacetic acid, EDTA)-promoted dissolution of CaCO 3 and complexation of Ca 2+ under basic (>pH 9) conditions, (Step 2a) Ca enrichment and separation using nanofiltration (NF), which allows separation of the Ca-EDTA complex from the accompanying bicarbonate (HCO 3 – ) species, (Step 2b) acidity-promoted decomplexation of Ca from EDTA, which allows near-complete chelator recovery and the formation of a Ca-enriched stream, and (Step 3) rapid precipitation of Ca(OH) 2 from the Ca-enriched stream using electrolytically produced alkalinity. These reactions can be conducted in a seawater matrix yielding coproducts including hydrochloric acid (HCl) and sodium bicarbonate (NaHCO 3 ), resulting from electrolysis and limestone dissolution, respectively. Careful analysis of the reaction stoichiometries and energy balances indicates that approximately 1.35 t of CaCO 3 , 1.09 t of water, 0.79 t of sodium chloride (NaCl), and ~2 MWh of electrical energy are required to produce 1 t of Ca(OH) 2 , with significant opportunity for process intensification. This approach has major implications for decarbonizing cement production within a paradigm that emphasizes the use of existing cement plants and electrification of industrial operations, while also creating approaches for alkalinity production that enable cost-effective and scalable CO 2 mineralization via Ca(OH) 2 carbonation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Effect of Carbon Nanofiber Clustering on the Micromechanical Properties of a Cement Paste

The use of carbon nanofibers (CNFs) in cement systems has received significant interest over the last decade due to their nanoscale reinforcing potential. However, despite many reports on the formation of localized CNF clusters, their effect on the cement paste micromechanical properties and relation to the mechanical response at the macroscopic scale are still not fully understood. In this study, grid nanoindentation coupled with scanning electron microscopy and energy dispersive spectroscopy was used to determine the local elastic indentation modulus and hardness of a portland cement paste containing 0.2% CNFs with sub-micro and microscale CNF clusters. The presence of low stiffness and porous assemblage of phases (modulus of 15–25 GPa) was identified in the cement paste with CNFs and was attributed primarily to the interfacial zone surrounding the CNF clusters. The CNFs favored the formation of higher modulus C–S–H phases (>30 GPa) in the bulk paste at the expense of the lower stiffness C–S–H. Nanoindentation results combined with a microscale–macroscale upscaling homogenization method further revealed an elastic modulus of the CNF clusters in the range from 18 to 21 GPa, indicating that the CNF clusters acted as compliant inclusions relative to the cement paste.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A machine learning approach for clinker quality prediction and nonlinear model predictive control design for a rotary cement kiln

Abstract Cement manufacturing is energy‐intensive (5Gj/t) and comprises a significant portion of the energy footprint of concrete systems. Incorporating modern monitoring, simulation and control systems will allow lower energy use, lower environmental impact, and lower costs of this widely used construction material. One of the goals of the CESMII roadmap project on the Smart Manufacturing of Cement included developing an analytical process model for clinker quality that includes the chemistry of the kiln feed and accounts for critical process variables. This predictive model will be used in nonlinear model predictive control system designed to significantly reduce process energy use while maintaining or improving product quality. In the cement manufacturing plant used in this study, the kiln feed (meal) is tested every 12 h and used to estimate the mineral composition of the cement kiln output (clinker) using the stoichiometry‐based Bogue's model and the expertise of the plant operators. During kiln operation, kiln output (clinker) is sampled and tested every 2 h to measure its chemical and mineral composition. The predicted and measured values of the clinker composition are used by the plant operators to adjust the kiln input stream and the production process characteristics to maintain stable operation and uniform product quality. However, the time delay between prediction and testing, along with inaccuracies inherent in the Bogue's model have made any process changes designed to minimize energy use problematic, especially in‐light of potential clinker quality issues that process changes often pose. A new analytical model that integrates quality information and process operation information has been developed from data collected from 2 years of production from an operating cement facility. To make the model fuel‐type‐independent, consumed heat energy was computed in the model instead of fuel type and amount. A Feedforward Network was trained and tailored from collected data. Many data‐based simulations were conducted to quantitatively evaluate the proposed model and the 5‐fold cross‐validation procedure was used to test the models. The resulting predictive model was shown to have a low root mean square error (MSE) with respect to the estimated clinker mineral composition compared to that using the industry standard “Bogue’ model”. The end goal of this work was to develop a single machine learning tool that allows the use of quality control data and process control variables to improve energy efficiency of the process in a continuous fashion. The proposed nonlinear model predictive control system (NMPC) can generate predicted kiln production characteristics based on manipulated variables in manner that accurately follows the target product quality values. Simulation results also show that the proposed model produced accurate predictions of kiln outputs that fell within the required constraints, while manipulating control variables within typical operational ranges.

Ali, Asem M.↗
DOE OSTI2024

Relevant biochar characteristics influencing compressive strength of biochar-cement mortars

To counteract the contribution of CO 2 emissions by cement production and utilization, biochar is being harnessed as a carbon-negative additive in concrete. Increasing the cement replacement and biochar dosage will increase the carbon offset, but there is large variability in methods being used and many researchers report strength decreases at cement replacements beyond 5%. This work presents a reliable method to replace 10% of the cement mass with a vast selection of biochars without decreasing ultimate compressive strength, and in many cases significantly improving it. By carefully quantifying the physical and chemical properties of each biochar used, machine learning algorithms were used to elucidate the three most influential biochar characteristics that control mortar strength: initial saturation percentage, oxygen-to-carbon ratio, and soluble silicon. These results provide additional research avenues for utilizing several potential biomass waste streams to increase the biochar dosage in cement mixes without decreasing mechanical properties.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Using high pressure solutions of polyfluoroacrylate and CO 2 to Seal cement cracks for improved wellbore integrity

Polyfluoroacrylate (PFA) is a hydrophobic and oleophobic polymer that is soluble in high pressure carbon dioxide (CO 2 ). In this study, the ability of PFA-CO 2 solutions to greatly reduce the apparent permeability of split or cracked Portland cement cylindrical samples is assessed. The apparent permeability values of confined samples were determined before and after treatment with PFA-CO 2 solutions. In four tests, PFA-CO 2 solutions were continuously displacing pure CO 2 from the cracked cement and the decrease in apparent permeability due to PFA adsorption and wettability alteration was monitored. The lowest apparent permeability cracked cement sample (81 nD) was completely sealed with a very small amount of solution. Samples with initial apparent permeabilities of 89 μD and 29.4 mD exhibited 92% and 99% reductions in permeability, respectively, before the experiments had to be stopped because of the excessively large increase in pressure drop. A 50% reduction in apparent permeability was observed with a 3.80 mD sample. Four other split cement samples (bound together with tape) with an initial apparent permeability in the 9.0–70 mD range were removed from the core holder and immersed in a PFA-CO 2 solution for 24 h to allow for PFA adsorption. Then the PFA-CO 2 solution was depressurized, allowing for the deposition of additional PFA from the solution within the crack as the pressure fell below the cloud point pressure of the PFA-CO 2 solution. These four samples were then confined again in a core holder and apparent permeability reductions of 29–93% were observed. Finally, results from these eight experiments indicates that the more substantial reductions in the nD – mD apparent permeability of the cracked cement correlated to lower initial crack permeability, higher PFA concentration, and slower injection rate of the PFA-CO 2 solution into the crack.

58 GEOSCIENCES↗
DOE OSTI2022

Geopolymer Cements: Resistance-Engineered Sewer Infrastructure for Longevity using Innovative, Energy-efficient, Synthesis Techniques (RESILIENT)

The primary objective of this project was to engineer an ultra-acid-resistant low-calcium alkali-activated cement paste for wastewater infrastructure applications to address the critical need for concrete materials with enhanced sulfuric acid resistance compared to ordinary Portland cement (OPC) concrete. In this project, the first milestone was to benchmark the sulfuric acid (SA) resistance of OPC and metakaolin-based geopolymer cement pastes. The second milestone was to model, select, and evaluate the efficacy of metal cation additions on the SA resistance of geopolymer cements. The third milestone was to create synthetic metakaolin that performed similarly to natural metakaolin. The fourth milestone was to design, build, and test the efficacy of four abiotic and biotic nano seeding agents. The fifth and final milestone was to quantify the breakeven material cost requirements and estimated environmental lifecycle costs of the most durable geopolymer cement formulations.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗