Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Burn”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Laminar Burning Speed Measurements of Hydrogen/Natural Gas Mixtures

Abstract To address the shortage of fossil fuels and the environmental impact of exhaust emissions, research efforts in combustion seek to identify candidates for sustainable fuels. Hydrogen is an example, from which water is produced as the main combustion product. However, when used as neat hydrogen, it is very difficult to control hydrogen combustion due to its high flame speed, pre-ignition propensity, and flashback characteristics. One method to control hydrogen combustion is to blend it with a well-established fuel. Natural gas is a common fuel for use in engines or gas turbines. Natural gas is characterized by slow flame speeds and poor lean-burn ability; thus, engine power is decreased in the lean-burn region. Consequently, natural gas engines are typically operated at stoichiometric conditions to maximize output. Blending hydrogen to natural gas has several advantages: (i) Control of hydrogen’s ignition characteristics, (ii) extension of Natural gas’s lower flammability limit — making it easier to ignite, and (iii) reduced greenhouse gas emissions. In this study, the laminar burning speed (LBS) for neat natural gas and natural gas/hydrogen mixtures at 5 atm and 296 K were measured. Schlieren optical imaging was utilized to validate laminar flame conditions and further investigate the structure of natural gas/hydrogen flames. Results indicate that replacing 50% of natural gas with hydrogen increases the peak laminar burning velocity by a factor of ∼1.6 times. LBS simulations were conducted with NUI 1.1 and UCF NG/H2 mechanisms; Predictions by both mechanisms were found to be satisfactory for neat NG mixtures. However, for 50% NG/ 50% H2 mixture, the true LBS for fuel-lean conditions was under-predicted by both models, while predictions for fuel-rich conditions were satisfactory. Additionally, a literature review and similar experimental analysis will be performed for methane, ammonia, and hydrogen fuel blends to better understand the combustion phenomena of natural gas fuels.

Yovino, Louis↗
DOE OSTI2023

AmeriFlux FLUXNET-1F CA-SF2 Saskatchewan - Western Boreal, forest burned in 1989

This is the AmeriFlux Management Project (AMP) created FLUXNET-1F version of the carbon flux data for the site CA-SF2 Saskatchewan - Western Boreal, forest burned in 1989. This is the FLUXNET version of the carbon flux data for the site CA-SF2 Saskatchewan - Western Boreal, forest burned in 1989 produced by applying the standard ONEFlux (1F) software. Site Description - Amiro_et_al_2006, AFM/136:...The 1989 burn site (F89) was northeast of Prince Albert National Park, Saskatchewan, with the humancaused fire covering 13,500 ha. Parts of the area had been logged prior to the fire, and slash residues would have been burned in some locations. Parts of the area were aerially seeded with jack pine seeds in the winter of 1990. The present tree canopy was composed of balsam poplar (Populus balsamifera L.), jack pine, trembling aspen, and birch (Betula papyrifera Marsh.) and prior to the fire, the stand consisted of these same species aswell asblack spruce.Deadsnags of black spruce and jack pinewere still standing, althoughmost had fallen over and formed a leaningmix of dry, dead tree boles. The understory vegetation consisted mostly of black spruce saplings, saplings of the tree overstory species, bearberry, blueberry (Vaccinium myrtilloides Michx.), raspberry (Rubus idaeus L.), rose (Rosa acicularis Lindl.), bunchberry (Cornus canadensis L.), and reed grass (Calamagrostis canadensis (Michx.) Nutt.).

Amiro, Brian↗
DOE OSTI2026

AmeriFlux FLUXNET-1F CA-SF3 Saskatchewan - Western Boreal, forest burned in 1998

This is the AmeriFlux Management Project (AMP) created FLUXNET-1F version of the carbon flux data for the site CA-SF3 Saskatchewan - Western Boreal, forest burned in 1998. This is the FLUXNET version of the carbon flux data for the site CA-SF3 Saskatchewan - Western Boreal, forest burned in 1998 produced by applying the standard ONEFlux (1F) software. Site Description - The 1998 burn site (F98) was in the east part of Prince Albert National Park, Saskatchewan, in the Waskesiu Fire, ignited by lightning that burned about 1700 ha in July 1998. The pre-fire forest consisted of jack pine and black spruce stands, with some intermixed aspen. The fire was severe, consuming much of the top layer of organic soil and killing all trees. In 2001, much of the regenerating vegetation consisted of aspen saplings about 1 m tall and shorter jack pine and black spruce seedlings. An overstory of dead, leafless jack pine trees dominated at a height of 18 m. Sparse grass and herbs, such as fireweed (Epilobium angustifolium L.) covered the ground. There were a large number of fallen dead trees, mostly perched above the ground and not decomposing quickly.

Amiro, Brian [University of Manitoba; Canadian For↗
DOE OSTI2020

Stability and Control of Burning Tokamak Plasmas with Resistive Walls (Second Year Report/ Final Report)

This research will focus on quantitative prediction of the stability, control, and equilibrium state evolution in toroidal burning plasmas. The stability of long pulse burning plasmas is highly sensitive to the physics of resonant layers in the plasma, sources of momentum and ow, kinetic effects of energetic particles, and boundary conditions at the wall, including feedback control and error fields. In ITER in particular, the low toroidal ow equilibrium state, sustained primarily by energetic alpha particles from fusion reactions, will require the consideration of all of these key elements to predict quantitatively the stability and evolution. The principal investigators on this proposal are leading experts in the relevant theoretical and computational areas, and aim to perform computations guided by analytic modeling, to address this physics in realistic configurations. The overall goal is to understand the key physics mechanisms that describe resistive toroidal burning plasmas, surrounded by a resistive wall, under active feedback control. With the physics of the energetic ions, resonant layers, resistive wall, and toroidal momentum transport included, this study will extend from recent publications in theory and simulation of individual effects and move toward predictive modeling for burning plasmas.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Stability and Control of Burning Tokamak Plasmas with Resistive Walls (Final Report)

This research has focused on quantitative prediction of the stability, control, and equilibrium state evolution in toroidal burning plasmas. The stability of long pulse burning plasmas is highly sensitive to the physics of resonant layers in the plasma, sources of momentum and flow, kinetic effects of energetic particles, and boundary conditions at the wall, including feedback control and error fields. In ITER in particular, the low toroidal flow equilibrium state, sustained primarily by energetic alpha particles from fusion reactions, will require the consideration of all of these key elements to predict quantitatively the stability and evolution. The principal investigators on this proposal are leading experts in the relevant theoretical and computational areas, and aimed to perform computations guided by analytic modeling, to address this physics in realistic configurations. The overall goal is to understand the key physics mechanisms that describe resistive toroidal burning plasmas, surrounded by a resistive wall, under active feedback control. With the physics of the energetic ions, resonant layers, resistive wall, and toroidal momentum transport included, this study will extend from recent publications in theory and simulation of individual effects and move toward predictive modeling for burning plasmas.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

2024 Results for Avian Monitoring at the Technical Area 36 Minie Site, Technical Area 39 Point 6, Technical Area 16 Burn Ground, and DARHT at Los Alamos National Laboratory

Los Alamos National Laboratory (LANL) biological subject matter experts in the Environmental Protection and Compliance Division initiated a multi-year program in 2013 to monitor avifauna (birds) at two open detonation sites and one open burn site on LANL property. Additional monitoring began in 2017 at a third firing site, the Dual-Axis Radiographic Hydrodynamic Test (DARHT) Facility. In this annual report, we compare monitoring results from these efforts among years to identify and evaluate firing and open burn site impacts on the local bird community. The objectives of this study are • to determine whether LANL operations impact bird abundance, species richness, or diversity; • to examine occupancy and nest success of secondary-cavity nesting birds that use nest boxes; and • to examine chemical concentrations (such as radionuclides, inorganic elements, and/or organic compounds) in nonviable eggs and deceased nestlings that are collected opportunistically with the upper-level bounds of background concentrations, when available. During May through July 2024, LANL biologists completed multiple avian point count surveys at each of the following treatment sites: • Technical Area (TA) 36 Minie Site, • TA-39 Point 6, • TA-16 Burn Ground, and • DARHT. We recorded a total of 1,088 birds that represented 65 species at the four treatment sites and compared these results with data from their associated control sites. In 2024, abundance and species richness at treatment and control sites continued to trend similarly from year to year, with minor random deviations expected from bird communities. Species richness at firing sites differed little from the previous year’s values. Two new bird species were observed at the firing sites—cedar waxwing (Bombycilla cedrorum) and pinyon jay (Gymnorhinus cyanocephalus). Shannon diversity values at TA-36 Minie Site, TA-39, and DARHT were statistically higher than one or more of their associated controls. Annual species diversity at treatment sites was high in 2024 across all firing sites relative to similar habitat control sites. We also monitored avian nest boxes to compare occupancy and nest success data from nest boxes at treatment sites with the overall avian nest box monitoring network and against a subset of relevant control sites. Nest box success has decreased at both treatment and control sites since monitoring began, suggesting that overlapping climatic factors are responsible for patterns of declining nest success. In 2024, nonviable avian eggs and one nestling were opportunistically collected at Bandelier National Monument, TA-16 Burn Ground, TA-36 Minie, TA-39 Point 6, and DARHT. All egg samples and the one nestling sample were evaluated for per- and polyfluoroalkyl substances, which were detected from all locations, including the control site at Bandelier National Monument. Overall results from 2024 continue to suggest that operations at the four treatment sites are not negatively impacting bird populations. This long-term project will continue to monitor for any changes over time.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

FIRED (Fire Events Delineation): An Open, Flexible Algorithm and Database of US Fire Events Derived from the MODIS Burned Area Product (2001–2019)

Harnessing the fire data revolution, i.e., the abundance of information from satellites, government records, social media, and human health sources, now requires complex and challenging data integration approaches. Defining fire events is key to that effort. In order to understand the spatial and temporal characteristics of fire, or the classic fire regime concept, we need to critically define fire events from remote sensing data. Events, fundamentally a geographic concept with delineated spatial and temporal boundaries around a specific phenomenon that is homogenous in some property, are key to understanding fire regimes and more importantly how they are changing. Here, we describe Fire Events Delineation (FIRED), an event-delineation algorithm, that has been used to derive fire events (N = 51,871) from the MODIS MCD64 burned area product for the coterminous US (CONUS) from January 2001 to May 2019. The optimized spatial and temporal parameters to cluster burned area pixels into events were an 11-day window and a 5-pixel (2315 m) distance, when optimized against 13,741 wildfire perimeters in the CONUS from the Monitoring Trends in Burn Severity record. The linear relationship between the size of individual FIRED and Monitoring Trends in Burn Severity (MTBS) events for the CONUS was strong (R2 = 0.92 for all events). Importantly, this algorithm is open-source and flexible, allowing the end user to modify the spatio-temporal threshold or even the underlying algorithm approach as they see fit. We expect the optimized criteria to vary across regions, based on regional distributions of fire event size and rate of spread. We describe the derived metrics provided in a new national database and how they can be used to better understand US fire regimes. The open, flexible FIRED algorithm could be utilized to derive events in any satellite product. We hope that this open science effort will help catalyze a community-driven, data-integration effort (termed OneFire) to build a more complete picture of fire.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Radiative heating rate profiles over the southeast Atlantic Ocean during the 2016 and 2017 biomass burning seasons

Marine boundary layer clouds, including the transition from stratocumulus to cumulus, are poorly represented in numerical weather prediction and general circulation models. Further uncertainties in the cloud structure arise in the presence of biomass burning carbonaceous aerosol, as is the case over the southeast Atlantic Ocean, where biomass burning aerosol is transported from the African continent. As the aerosol plume progresses across the southeast Atlantic Ocean, radiative heating within the aerosol layer has the potential to alter the thermodynamic environment and therefore the cloud structure; however, limited work has been done to quantify this along the trajectory of the aerosol plume in the region. The deployment of the first Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF1) in support of the Layered Atlantic Smoke Interactions with Clouds field campaign provided a unique opportunity to collect observations of cloud and aerosol properties during two consecutive biomass burning seasons during July through October of 2016 and 2017 over Ascension Island (7.96° S, 14.35° W). Using observed profiles of temperature, humidity, and clouds from the field campaign alongside aerosol optical properties from Modern-Era Retrospective analysis for Research and Applications, Version 2 (MERRA-2), as input for the Rapid Radiation Transfer Model (RRTM), profiles of the radiative heating rate due to aerosols and clouds were computed. Radiative heating is also assessed across the southeast Atlantic Ocean using an ensemble of back trajectories from the Hybrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model. Idealized experiments using the RRTM with and without aerosols and a range of values for the single-scattering albedo (SSA) demonstrate that shortwave (SW) heating within the aerosol layer above Ascension Island can locally range between 2 and 8 K d -1 depending on the aerosol optical properties, though impacts of the aerosol can be felt elsewhere in the atmospheric column. When considered under clear conditions, the aerosol has a cooling effect at the TOA, and based on the observed cloud properties at Ascension Island, the cloud albedo is not large enough to overcome this. Shortwave radiative heating due to biomass burning aerosol is not balanced by additional longwave (LW) cooling, and the net radiative impact results in a stabilization of the lower troposphere. However, these results are extremely sensitive to the single-scattering albedo assumptions in models.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Open cells exhibit weaker entrainment of free-tropospheric biomass burning aerosol into the south-east Atlantic boundary layer

This work presents synergistic satellite, airborne and surface-based observations of a pocket of open cells (POC) in the remote south-east Atlantic. The observations were obtained over and upwind of Ascension Island during the CLouds and Aerosol Radiative Impacts and Forcing (CLARIFY) and the Layered Smoke Interacting with Clouds (LASIC) field experiments. A novel aspect of this case study is that an extensive free-tropospheric biomass burning aerosol plume that had been transported from the African continent was observed to be in contact with the boundary layer inversion over the POC and the surrounding closed cellular cloud regime. The in situ measurements show marked contrasts in the boundary layer thermodynamic structure, cloud properties, precipitation and aerosol conditions between the open cells and surrounding overcast cloud field. The data demonstrate that the overlying biomass burning aerosol was mixing down into the boundary layer in the stratocumulus cloud downwind of the POC, with elevated carbon monoxide, black carbon mass loadings and accumulation-mode aerosol concentrations measured beneath the trade-wind inversion. The stratocumulus cloud in this region was moderately polluted and exhibited very little precipitation falling below cloud base. A rapid transition to actively precipitating cumulus clouds and detrained stratiform remnants in the form of thin quiescent veil clouds was observed across the boundary into and deep within the POC. The subcloud layer in the POC was much cleaner than that in the stratocumulus region. The clouds in the POC formed within an ultra-clean layer (accumulation-mode aerosol concentrations of approximately a few cm -3 ) in the upper region of the boundary layer, which was likely to have been formed via efficient collision–coalescence and sedimentation processes. Enhanced Aitken-mode aerosol concentrations were also observed intermittently in this ultra-clean layer, suggesting that new particle formation was taking place. Across the boundary layer inversion and immediately above the ultra-clean layer, accumulation-mode aerosol concentrations were ~1000 cm -3 . Importantly, the air mass in the POC showed no evidence of elevated carbon monoxide over and above typical background conditions at this location and time of year. As carbon monoxide is a good tracer for biomass burning aerosol that is not readily removed by cloud processing and precipitation, it demonstrates that the open cellular convection in the POC is not able to entrain large quantities of the free-tropospheric aerosol that was sitting directly on top of the boundary layer inversion. This suggests that the structure of the mesoscale cellular convection may play an important role in regulating the transport of aerosol from the free troposphere down into the marine boundary layer. We then develop a climatology of open cellular cloud conditions in the south-east Atlantic from 19 years of September Moderate Resolution Imaging Spectroradiometer (MODIS) Terra imagery. This shows that the maxima in open cell frequency (> 0.25) occurs far offshore and in a region where subsiding biomass burning aerosol plumes may often come into contact with the underlying boundary layer cloud. If the results from the observational case study applied more broadly, then the apparent low susceptibility of open cells to free-tropospheric intrusions of additional cloud condensation nuclei could have some important consequences for aerosol–cloud interactions in the region.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Biomass burning and marine aerosol processing over the southeast Atlantic Ocean: a TEM single-particle analysis

This study characterizes single-particle aerosol composition from filters collected during the ObseRvations of Aerosols above CLouds and their intEractionS (ORACLES) and CLoud–Aerosol–Radiation Interaction and Forcing: Year 2017 (CLARIFY-2017) campaigns. In particular the study describes aged biomass burning aerosol (BBA), its interaction with the marine boundary layer and the influence of biomass burning (BB) air on marine aerosol. The study finds evidence of BBA influenced by marine boundary layer processing as well as sea salt influenced by BB air. Secondary chloride aerosols were observed in clean marine air as well as in BB-influenced air in the free troposphere. Higher-volatility organic aerosol appears to be associated with increased age of biomass burning plumes, and photolysis or oxidation may be a mechanism for the apparent increased volatility. Aqueous processing and interaction with the marine boundary layer air may be a mechanism for the presence of sodium on many aged potassium salts. By number, biomass burning potassium salts and modified sea salts are the most observed particles on filter samples. The most commonly observed BC coatings are inorganic salts. These results suggest that atmospheric processes such as photolysis, oxidation and cloud processing are key drivers in the elemental composition and morphology of aged BBA. Fresh BBA inorganic salt content, as it has an important role in the particles' ability to uptake water, may be a key driver in how aqueous processing and atmospheric aging proceed.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Burn severity and vegetation type control phosphorus concentration, molecular composition, and mobilization

Shifting phosphorus (P) dynamics after wildfires can have cascading impacts from terrestrial to aquatic environments. However, it is unclear whether shifts in P composition or P concentration are responsible for changes in P dynamics post-fire. We used laboratory leaching experiments of Douglas fir forest and sagebrush shrubland chars to examine how the potential mobility of P compounds is influenced by different burn severities. Burning produced a 6.9- and 29-fold increase in particulate P mobilization but a 3.8- and 30.5-fold decrease in aqueous P released for Douglas fir forest and sagebrush shrubland, respectively. The mechanisms driving particulate- and dissolved-phase P compound mobilization were contrasting. Phosphorus compound mobilization in the particulate phase was controlled by solid char total P concentrations, while the aqueous phase was driven by solubility changes of molecular species. Nuclear magnetic resonance (NMR) and X-ray absorption near-edge structure (XANES) on the solid chars indicated that organic orthophosphate monoester and diester species were thermally mineralized to inorganic P moieties with burning in both vegetation types, which decreases P solubility. This coincided with the production of calcium- and magnesium-bound inorganic P compounds. With increasing burn severity there were systematic shifts in P concentration and composition – higher-severity chars mobilized P compounds in the particulate phase, although the magnitude of change was vegetation-specific. Our results indicate a post-fire transformation to both the composition of the solid charred material and how P compounds are mobilized, which may influence its environmental cycling and fate.

31P solution-state NMR↗
DOE OSTI2023

Experiments and Simulations of Droplet Burning of Isobutanol Mixed with a Tier II Gasoline Certification Fuel and its Surrogate, Paper Number: SHTC2023-115267

This study presents an experimental and numerical results of combustion dynamics of a Tier II certification fuel/iso-butanol mixtures and its surrogate(S5)/iso-butanol mixtures. The experiments were carried out where gas transport was determined entirely by fuel evaporation to promote spherical symmetry during the burning process. The droplet initial diameters were in the range 0.55 mm to 0.62 mm. The combustion characteristics such as droplet diameters, flame standoff ratios and soot shell standoff ratios of indolene/iso-butanol mixtures are compared with S5/iso-butanol mixtures and the implications of iso-butanol addition to indolene and S5 on combustion are discussed. The presence of iso-butanol is experimentally found to reduce the formation of soot as the iso-butanol concentration was increased and the iso-butanol addition insignificantly influence the burning rate. Simulations were carried out with the detailed kinetic chemistry (324 species and 17608 reactions) from POLIMI. The detailed numerical model included unsteady gas and liquid transport, soot chemistry and radiative transport. The impact of iso-butanol on the burning rate, flame structure and soot formation are presented. Droplet burn rates were well predicted while flame diameters showed more variability depending on how the flame was defined in the numerical simulation (peak gas temperature and OH concentration). Simulations also show the influence of iso-butanol concentration on flame temperature, greenhouse gas emissions and soot formations.

Guo, Songtao↗
DOE OSTI2021

Results from single-shock Marble experiments studying thermonuclear burn in the presence of heterogeneous mix on the National Ignition Facility

The Marble campaign on the National Ignition Facility investigates the effect of heterogeneous mix on thermonuclear burn for comparison to a probability distribution function (PDF) burn model. Marble utilizes plastic capsules filled with deuterated plastic foam and a fill gas containing tritium. As the capsules implode, the deuterium in the foam mixes with the tritium gas, and DT neutrons are produced as the shocks compress and heat the mixture. The yield of DT neutrons is dependent on the uniformity of the mix, with more heterogeneous mix producing fewer neutrons. In Marble, the heterogeneity of the mix is controlled by varying the diameter of voids introduced into the foam. The first NIF Marble campaign has been executed in which the Marble capsules were indirectly driven with a single strong shock using NIF hohlraums. The experiments produce a low-convergence, high-ion-temperature implosion. The ratio of DT to DD neutron yield is largely consistent with uniform atomic mix for fine-pore foam, and increases slightly with void diameter, contrary to 1D simulations using the PDF burn model. Recent 3D high-resolution simulations of similar experiments performed on the Omega Laser Facility suggest an explanation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Predictive binder jet additive manufacturing enabled by clean burn-off binder design

Binder jet additive manufacturing (BJAM) presents an avenue for advanced manufacturing of various high-value materials due to high deposition rates, scalability, and geometric flexibility. However, conventional organic binders in BJAM introduce residual carbon upon pyrolysis, often leading to imprecise alloy composition in the final sintered part. The undesirable residual carbon from binder burn-off limits the application of BJAM for high-performance alloys due to their high sensitivity to carbon addition. In this study, we have designed poly(vinylpyrrolidone-co-vinyl acetate) (PVP-VAc) as a clean burn-off binder for BJAM, where excess oxygen groups in VAc enable cleaner burn-off and reduce residual carbon retention. Compared to a widely used commercial binder, the optimized PVP-VAc binder reduced residual carbon retention by over 90% in H13 tool steel. The significant reduction in residual carbon enables predictable printing and subsequent sintering of complex H13 tool steel geometries, an alloy known to have substantial challenges around distortion due to the sintering window shifting from carbon addition. The design of a clean burnout binder provides a major path forward for BJAM by enabling new AM designs and applications for composition-sensitive high-performance alloys, such as nickel-based superalloys, titanium alloys, and high alloyed steels.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Simulation of the effects of biomass burning in a mesoscale convective system in the central amazon

During the dry season of 2014, the formation of a mesoscale convective system (MCS) caused intense precipitation and strong winds in the central Amazon region. In this period, cases of MCS that occurred during the days when there were higher concentrations of CO were analyzed. Through this criterion, a case of MCS occurred on August 16th, 2014 was selected. We used the chemical-atmospheric model WRF-Chem to assess the influence of biomass burning aerosol on the intensity of precipitation, winds, vertical and horizontal transport associated with this convective system. We show that biomass burning aerosol reduces the strength of the mesoscale convective system, with less vertical and horizontal transport of carbon monoxide and ozone. Here, in the absence of biomass burning aerosol downdrafts and precipitation rate are more intense, and cloud development up to 5km is more developed, making the horizontal flow and vertical transport of ozone more intense, however, much more efficient in reducing the concentrations of other gases.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

New Particle Formation Events Over the Southeast Atlantic Coincide With the African Biomass Burning Season

Abstract We investigated the occurrence and evolution of new particle formation (NPF) events over the southeast Atlantic. The studied region is under the influence of the long‐range transport of aerosols and gases during the southern African biomass burning season, from June to October every year. Interestingly, NPF was observed to coincide with the African biomass burning season, although wet removal of pre‐existing aerosols is needed during these NPF events. Surface and airborne measurements show that these NPF events likely occurred in the upper region of the marine boundary layer, and the newly formed aerosols were further transported to the surface via vertical air motions. Using a box model, we predicted that a large fraction of these particles could grow to sizes related to cloud condensation nuclei. Our study shows that NPF can occur over the southeast Atlantic, and the African biomass‐burning plume likely contributed to the NPF occurrence.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Sensitivity of Regional WRF‐Chem Air Quality and Weather Simulations to Biomass‐Burning Emission Data Sets: A Case Study of the Impact of Canadian Wildfire on the US°

This study focuses on the period from June 26 to 29, 2023, when record‐breaking Canadian wildfires severely impacted air quality in the Midwest United States. Using the Weather Research and Forecasting Model with Chemistry (WRF‐Chem) and four biomass‐burning data sets (Fire Inventory from NCAR version 1, Fire Inventory from NCAR version 2.5, Quick Fire Emissions Data set [QFED], and Regional ABI‐VIIRS Emission), we analyzed aerosol transport from Canada to the US and assessed the model's accuracy in predicting PM 2.5 , O 3 , CO and aerosol weather feedback. Model simulations were compared with ground‐based and remote sensing observations as well as field measurements from the Community Research on Climate and Urban Science (CROCUS) project. Our findings show that the movement of a low‐pressure system from the Great Lakes to the Atlantic, combined with the high‐pressure system over the Atlantic, caused the transport of aerosols from Canadian wildfires to the US. Results show WRF‐Chem significantly underestimated key atmospheric components: aerosol optical depth (AOD) by over 50%, PM 2.5 by 65%–90% and peak O 3 concentrations by 50%–55% across four biomass burning data sets. Additionally, CO and NO 2 concentrations were underpredicted. The substantial underestimation of PM 2.5 led to an overestimation of temperature by up to 3.6 °C primarily due to excessive downward shortwave radiation, which resulted from the underestimation of direct aerosol effects and an increase in sensible heat flux. Among the biomass‐burning data sets, QFED produced the most accurate AOD and PM 2.5 predictions due to improved wildfire emission estimates, leading to a 1.0 to 1.5 °C reduction in temperature overestimation during the daytime. These findings underscore the need for improving wildfire emission estimates for trace gases and aerosols to enhance air quality and weather feedback predictions.

WRF-chem model↗
DOE OSTI2022

Cloud processing and weeklong ageing affect biomass burning aerosol properties over the south-eastern Atlantic

Abstract Southern Africa produces a third of global biomass burning emissions, which have a long atmospheric lifetime and influence regional radiation balance and climate. Here, we use airmass trajectories to link different aircraft observations to investigate the evolution of biomass-burning aerosols during their westward transport from Southern Africa over the south-eastern Atlantic, where a semi-permanent stratocumulus cloud deck is located. Our results show secondary organic aerosol formation during the initial 3 days of transport, followed by decreases in organic aerosol via photolysis before reaching equilibrium. Aerosol absorption wavelength dependency decreases with ageing, due to an increase in particle size and photochemical bleaching of brown carbon. Cloud processing, including aqueous-phase reaction and scavenging, contributes to the oxidation of organic aerosols, while it strongly reduces large diameter particles and single-scattering albedo of biomass burning aerosols. Together, these processes resulted in a marine boundary layer with fewer yet more oxidized and absorbing aerosols.

54 ENVIRONMENTAL SCIENCES↗