Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Boundary identification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Verification and Validation of Safety-Critical Aircraft Systems Operating under Off-Nominal, Contingency, and Emergency Conditions

Verification and validation (V&V) of safety-critical technologies developed for loss of control (LOC) prevention and recovery and other aviation safety concerns pose significant challenges. Aircraft LOC can result from a wide spectrum of hazards, often occurring in combination, which cannot be fully replicated during evaluation. Technologies developed for LOC prevention and recovery must therefore be effective under a wide variety of hazardous and uncertain conditions, and the verification and validation of these technologies must provide some measure of assurance that the new vehicle safety technologies do no harm (i.e., that they themselves do not introduce new safety risks). V&V technologies must also enable the identification of system limitations and constraints, as well as enable the identification of safe and unsafe operating conditions (and their boundaries). Additionally, the V&V of complex, increasingly autonomous systems is a fundamental concern. Scalable, reproducible and cost-effective techniques for the assurance of safety critical systems during their design and operation is a key barrier to fielding new systems or updating current systems. Moreover, these techniques need to provide artifacts that enable a comprehensive evidence-based approach to certification. This briefing summarizes research performed under NASA’s Aviation Safety Program and follow-on research for the V&V of safety-critical aircraft system technologies developed for LOC prevention and recovery and increasingly autonomous systems, and for a broad assurance capability in both current and emerging aviation applications. Note that, in this briefing, the term “validation” refers to a confirmation that the system implementation (e.g., algorithms etc.) is performing the intended function(s), as well as an affirmation of effectiveness in these functions. “Verification” refers to a confirmation that the system implementation in the software and hardware meets its (hopefully validated) specifications (e.g., correctly executes algorithms as designed).

Validation↗
DOE OSTI2025

Two-frequency RF fields induced multipactor in coaxial transmission lines

This study presents a comprehensive investigation of two-surface multipactor discharge in coaxial transmission lines under two-frequency radio frequency (RF) excitation using one-dimensional Monte Carlo simulations validated against three-dimensional particle-in-cell simulations and experimental data. The results show that introducing a second carrier mode can suppress multipactor by reshaping and shrinking the susceptibility region, with the extent and location of suppression strongly dependent on the device's aspect ratio and the relative phase of the second carrier mode. Distinct suppression patterns are observed across different fd regimes, while in some cases, susceptibility expansion also occurs under two-frequency operation. A key outcome is the identification and delineation of pure and mixed multipactor modes in coaxial geometry, where analytical mode boundaries are not readily available. Unlike planar geometries, pure-mode regions in coaxial systems overlap with mixed-mode domains, complicating mode identification. Additionally, image charge forces are found to have negligible influence on susceptibility thresholds but strongly affect electron growth rates. These findings offer valuable insights into the use of waveform engineering for controlling multipactor in high-power RF systems.

43 PARTICLE ACCELERATORS↗
NASA NTRS2008

Towards Verification of Unstructured-Grid Solvers

New methodology for verification of computational methods using unstructured grids is presented. The discretization order properties are studied in computational windows, easily constructed within a collection of grids or a single grid. The windows can be adjusted to isolate the interior discretization, the boundary discretization, or singularities. A major component of the methodology is the downscaling test, introduced previously for studying the convergence rates of truncation and discretization errors of finite-volume discretization schemes on general unstructured grids. Demonstrations of the method are shown, including a comparative accuracy assessment of commonly-used schemes on general mixed grids and the identification of local accuracy deterioration at intersections of tangency and inflow/outflow boundaries. Recommendations for the use of the methodology in large-scale computational simulations are given.

Thomas, James L.↗
DOE OSTI2021

Toward active disruption avoidance via real-time estimation of the safe operating region and disruption proximity in tokamaks

This paper describes a real-time capable algorithm for identifying the safe operating region around a tokamak operating point. The region is defined by a convex set of linear constraints, from which the distance of a point from a disruptive boundary can be calculated. The disruptivity of points is calculated from an empirical machine learning predictor that generates the likelihood of disruption. While the likelihood generated by such empirical models can be compared to a threshold to trigger a disruption mitigation system, the safe operating region calculation enables active optimization of the operating point to maintain a safe margin from disruptive boundaries. The proposed algorithm is tested using a random forest disruption predictor fit on data from DIII-D. The safe operating region identification algorithm is applied to historical data from DIII-D showing the evolution of disruptive boundaries and the potential impact of optimization of the operating point. Real-time relevant execution times are made possible by parallelizing many of the calculation steps and implementing the algorithm on a graphics processing unit. Lastly, a real-time capable algorithm for optimizing the target operating point within the identified constraints is also proposed and simulated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2001

Aeroservoelastic Uncertainty Model Identification from Flight Data

Uncertainty modeling is a critical element in the estimation of robust stability margins for stability boundary prediction and robust flight control system development. There has been a serious deficiency to date in aeroservoelastic data analysis with attention to uncertainty modeling. Uncertainty can be estimated from flight data using both parametric and nonparametric identification techniques. The model validation problem addressed in this paper is to identify aeroservoelastic models with associated uncertainty structures from a limited amount of controlled excitation inputs over an extensive flight envelope. The challenge to this problem is to update analytical models from flight data estimates while also deriving non-conservative uncertainty descriptions consistent with the flight data. Multisine control surface command inputs and control system feedbacks are used as signals in a wavelet-based modal parameter estimation procedure for model updates. Transfer function estimates are incorporated in a robust minimax estimation scheme to get input-output parameters and error bounds consistent with the data and model structure. Uncertainty estimates derived from the data in this manner provide an appropriate and relevant representation for model development and robust stability analysis. This model-plus-uncertainty identification procedure is applied to aeroservoelastic flight data from the NASA Dryden Flight Research Center F-18 Systems Research Aircraft.

Brenner, Martin J.↗
NASA NTRS1982

The influence of solar active region evolution on solar wind streams, coronal hole boundaries and geomagnetic storms

Solar and interplanetary data are examined, taking into account the identification of the heliographic longitudes of the coronal source regions of high speed solar wind (SW) streams by Nolte and Roelof (1973). Nolte and Roelof have 'mapped' the velocities measured near earth back to the sun using the approximation of constant radial velocity. The 'Carrington carpet' for rotations 1597-1616 is shown in a graph. Coronal sources of high speed streams appear in the form of solid black areas. The contours of the stream sources are laid on 'evolutionary charts' of solar active region histories for the Southern and Northern Hemispheres. Questions regarding the interplay of active regions and solar wind are investigated, giving attention to developments during the years 1973, 1974, and 1975.

Gold, R. E.↗
NASA NTRS1973

A study of the utilization of ERTS-1 data from the Wabash River Basin

The author has identified the following significant results. Nine projects are defined, five ERTS data applications experiments and four supporting technology tasks. The most significant applications results were achieved in the soil association mapping, earth surface feature identification, and urban land use mapping efforts. Four soil association boundaries were accurately delineated from ERTS-1 imagery. A data bank has been developed to test surface feature classifications obtained from ERTS-1 data. Preliminary forest cover classifications indicated that the number of acres estimated tended to be greater than actually existed by 25%. Urban land use analysis of ERTS-1 data indicated highly accurate classification could be obtained for many urban catagories. The wooded residential category tended to be misclassified as woods or agricultural land. Further statistical analysis revealed that these classes could be separated using sample variance.

Landgrebe, D. A.↗
NASA NTRS1990

A neural network approach to cloud classification

It is shown that, using high-spatial-resolution data, very high cloud classification accuracies can be obtained with a neural network approach. A texture-based neural network classifier using only single-channel visible Landsat MSS imagery achieves an overall cloud identification accuracy of 93 percent. Cirrus can be distinguished from boundary layer cloudiness with an accuracy of 96 percent, without the use of an infrared channel. Stratocumulus is retrieved with an accuracy of 92 percent, cumulus at 90 percent. The use of the neural network does not improve cirrus classification accuracy. Rather, its main effect is in the improved separation between stratocumulus and cumulus cloudiness. While most cloud classification algorithms rely on linear parametric schemes, the present study is based on a nonlinear, nonparametric four-layer neural network approach. A three-layer neural network architecture, the nonparametric K-nearest neighbor approach, and the linear stepwise discriminant analysis procedure are compared. A significant finding is that significantly higher accuracies are attained with the nonparametric approaches using only 20 percent of the database as training data, compared to 67 percent of the database in the linear approach.

Lee, Jonathan↗
NASA NTRS1993

Particle tracing in the magnetosphere - New algorithms and results

A fast and efficient method is employed to trace charged particles through realistic magnetospheric electric and magnetic fields, greatly reducing computer simulation times. The method is applicable for particles having arbitrary charge, energy, or pitch angle but which conserve the first two adiabatic invariants. An efficient method is used to classify drift orbits, which greatly facilitates identification of the last closed drift path or other drift boundaries. The time-independent evolution of the bounce-averaged phase space density along convective drift orbits is calculated. These three tools can be used to quantitatively describe convective evolution of the particle distribution from the tail, an essential step in understanding the production of unstable distributions in the magnetosphere.

Sheldon, R. B.↗
NASA NTRS1994

Distribution of siderophile and other trace elements in melt rock at the Chicxulub impact structure

Recent isotopic and mineralogical studies have demonstrated a temporal and chemical link between the Chicxulub multiring impact basin and ejecta at the Cretaceous-Tertiary boundary. A fundamental problem yet to be resolved, however, is identification of the projectile responsible for this cataclysmic event. Drill core samples of impact melt rock from the Chichxulub structure contain Ir and Os abundances and Re-Os isotopic ratios indicating the presence of up to approx. 3 percent meteoritic material. We have used a technique involving microdrilling and high sensitivity instrumental neutron activation analysis (INAA) in conjunction with electron microprobe analysis to characterize further the distribution of siderophile and other trace elements among phases within the C1-N10 melt rock.

Schuraytz, B. C.↗
NASA NTRS1995

Ignition and combustion of bulk metals under elevated, normal and reduced gravity conditions

This research effort is aimed at providing further insight into this multi-variable dependent phenomena by looking at the effects of gravity on the ignition and combustion behavior of metals. Since spacecraft are subjected to higher-than-1g gravity loads during launch and reentry and to zero-gravity environments while in orbit, the study of ignition and combustion of bulk metals at different gravitational potentials is of great practical concern. From the scientific standpoint, studies conducted under microgravity conditions provide simplified boundary conditions since buoyancy is removed, and make possible the identification of fundamental ignition mechanisms. The effect of microgravity on the combustion of bulk metals has been investigated by Steinberg, et al. on a drop tower simulator. However, no detailed quantitative work has been done on ignition phenomena of bulk metals at lower or higher-than-normal gravitational fields or on the combustion characteristics of metals at elevated gravity. The primary objective of this investigation is the development of an experimental system capable of providing fundamental physical and chemical information on the ignition of bulk metals under different gravity levels. The metals used in the study, iron (Fe), titanium (Ti), zirconium (Zr), magnesium (Mg), zinc (Zn), and copper (Cu) were selected because of their importance as elements of structural metals and their simple chemical composition (pure metals instead of multi-component alloys to avoid complication in morphology and spectroscopic studies). These samples were also chosen to study the two different combustion modes experienced by metals: heterogeneous or surface oxidation, and homogeneous or gas-phase reaction. The experimental approach provides surface temperature profiles, spectroscopic measurements, surface morphology, x-ray spectrometry of metals specimens and their combustion products, and high-speed cinematography of the heating, ignition and combustion stages of the metal specimen. This paper summarizes the results obtained to date from experiments conducted under normal and high-gravity conditions.

Abbud-Madrid, Angel↗
NASA NTRS1997

The Effect of Gravity on the Combustion of Bulk Metals

In recent years, metal combustion studies at the University of Colorado have focused on the effects of gravity (g) on the ignition and burning behavior of bulk metals. The impetus behind this effort is the understanding of the ignition conditions and flammability properties of structural metals found in oxygen (O2) systems for space applications. Since spacecraft are subjected to higher-than-1g loads during launch and reentry and to a zero-gravity environment while in orbit, the study of ignition and combustion of bulk metals at different gravitational accelerations is of great practical concern. From the scientific standpoint, studies conducted under low gravity conditions provide simplified boundary conditions, since buoyancy is removed, and make possible the identification of fundamental ignition and combustion mechanisms. This investigation is intended to provide experimental verification of the influence of natural convection on the burning behavior of metals. In addition, the study offers the first findings of the influence of gravity on ignition of bulk metals and on the combustion mechanism and structure of metal-oxygen, vapor-phase diffusion flames in a buoyancy-free environment. Titanium (Ti) and magnesium (Mg) metals were chosen because of their importance as elements of structural materials and their simple chemical composition-pure metals instead of multicomponent alloys to simplify chemical and spectroscopic analyses. In addition, these elements present the two different combustion modes observed in metals: heterogeneous or surface burning (for Ti) and homogeneous or gas-phase reaction (for Mg). Finally, Mg, Ti, and their oxides exhibit a wide range of thermophysical and chemical properties. Metal surface temperature profiles, critical and ignition temperatures, propagation rates, burning times, and spectroscopic measurements are obtained under normal and reduced gravity. Visual evidence of all phenomena is provided by high-speed photography.

Branch, Melvyn C.↗
NASA NTRS2008

Aerosol Profile Measurements from the NASA Langley Research Center Airborne High Spectral Resolution Lidar

Since achieving first light in December of 2005, the NASA Langley Research Center (LaRC) Airborne High Spectral Resolution Lidar (HSRL) has been involved in seven field campaigns, accumulating over 450 hours of science data across more than 120 flights. Data from the instrument have been used in a variety of studies including validation and comparison with the Cloud- Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) satellite mission, aerosol property retrievals combining passive and active instrument measurements, aerosol type identification, aerosol-cloud interactions, and cloud top and planetary boundary layer (PBL) height determinations. Measurements and lessons learned from the HSRL are leading towards next-generation HSRL instrument designs that will enable even further studies of aerosol intensive and extensive parameters and the effects of aerosols on the climate system. This paper will highlight several of the areas in which the NASA Airborne HSRL is making contributions to climate science.

Obland, Michael D.↗
NASA NTRS2010

Internal Acoustics of a Pintle Valve with Supercritical Helium Flow

Large amplitude flow unsteadiness is a common phenomenon within the high flow rate ducts and valves associated with propulsion systems. Boundary layer noise, shear layers and vortex shedding are a few of the many sources of flow oscillations. The presence of lightly damped acoustic modes can organize and amplify these sources of flow perturbation, causing undesirable loading of internal parts. The present study investigates the self-induced acoustic environment within a pintle valve subject to high Reynolds Number flow of helium gas. Experiments were conducted to measure the internal pressure oscillations of the Ares I Launch Abort System (LAS) Attitude Control Motor (ACM) valve. The AGM consists of a solid propellant gas generator with eight pintle valves attached to the aft end. The pintle valve is designed to deliver variable upstream conditions to an attache( converging diverging nozzle. In order to investigate the full range of operating conditions 28 separate tests were conducted with varying pintle position and upstream pressure. Helium gas was utilized in order to closely mimic the speed of sound of the gas generator exhaust, minimizing required scaling during data analysis. The recordec pressure measurements were interrogated to multiple ends. The development of root mean square (RMS) value! versus Reynolds Number and Pintle position are important to creating bounding unsteady load curves for valve internal parts. Spectral analysis was also performed, helping to identify power spectral densities (PSD) of acoustic natural frequencies and boundary layer noise. An interesting and unexpected result was the identification of an acoustic mode within the valve which does not respond until the valve was over 60% open. Further, the response amplitude around this mode can be as large or larger than those associated with lower frequency modes.

Fishbach, Sean R.↗
NASA NTRS2006

A Scheme for finding the Front Boundary of an Interplanetary Magnetic Cloud

We developed a scheme for finding the front boundary of an interplanetary magnetic cloud (MC) based on criteria that depend on the possible existence of any one or all of six specific solar wind features. The features that the program looks for, within +/- 2 hours of a preliminarily determined time for the front boundary, estimated either by visual inspection or by an automatic MC identification scheme, are: (1) a sufficiently large directional discontinuity in the interplanetary magnetic field (IMF), (2) existence of a magnetic hole, (3) a significant proton plasma beta drop, (4) a significant proton temperature drop, (5) a marked increase in the IMF's intensity, and (6) a significant decrease in a normalized root-mean-square deviation (RMS)of the magnetic field - where the scheme was tested using 5, 10, 15, and 20 minute averages of the relevant physical quantities, in order to find the optimum average (and RMS) to use. Other criteria, besides these six, were examined and dismissed as not reliable, e.g., plasma speed. The scheme was developed specifically for aiding in forecasting the strength and timing of a geomagnetic storm due to the passage of an interplanetary MC in real-time, but can be used in post ground-data collection for imposition of consistency in choosing a MC's front boundary. The scheme has been extensively tested, first using 80 bona fide MCs over about 9 years of WIND data, and also for 121 MC-like structures as defined by a program that automatically identifies such structures over the same period. Optimum limits for various parameters in the scheme were found by statistical studies of the WIND MCs. The resulting limits can be user-adjusted for other data sets, if desired. Final testing of the 80 MCs showed that for 50 percent of the events the boundary estimates occurred within +/-10 minutes of visually determined times, 80 percent occurred within +/-30 minutes, and 91 percent occur within +/-60 minutes, and three or more individual boundary tests were passed for 88 percent of the total MCs. The scheme and its testing will be described.

Lepping, Ronald P.↗
NASA NTRS2020

Study of Antarctic Blowing Snow Storms Using MODIS and CALIOP Observations With a Machine Learning Model

As a common phenomenon over Antarctica, blowing snow (BLSN), especially the large BLSN storms, play an important role in the Antarctic surface mass balance, radiation budget, and planetary boundary layer processes. This study presents the work on BLSN storm identification and analysis with observations from the Moderate Resolution Imaging Spectroradiometer (MODIS) onboard the Aqua satellite. Spectral analysis shows that BLSN identification is feasible with MODIS daytime data. A random forest machine learning model is developed and observations from the Cloud‐Aerosol Lidar with Orthogonal Polarization are used for training. Model performance results show that machine‐learning based classification can achieve over 90% overall accuracy when classifying MODIS pixels into cloud, clear, and BLSN categories. The machine learning model is applied to MODIS observations during the month of October 2009 for BLSN storm analysis. Results show that the size of BLSN storms has a large spectrum and can reach hundreds of thousands km2. The MODIS based BLSN storm frequency map extends the Cloud‐Aerosol Lidar and Infrared Pathfinder Satellite Observations coverage limit from 82°S to the South Pole. A BLSN storm belt, which extends from the South Pole region to the coastal area between 130°E and 160°E along the Transantarctic Mountains, provides a potential pathway of snow transport. These results are important in improving the understanding of BLSN impact on Antarctic surface mass balance and boundary layer processes.

Antarctic↗
DOE OSTI2021

A Bayesian Framework for Milling Stability Prediction and Reverse Parameter Identification

This paper describes a physics-guided Bayesian framework for identifying the milling stability boundary and system parameters through iterative testing. Prior uncertainties for the parameters are identified through physical simulation and literature reviews, without physical testing of the actual milling system. Those uncertainties are then propagated to the stability map using a physics-based stability model, which is used to suggest a test point. The uncertainties are updated based on the new information acquired from the cutting test to form a new probability distribution, called the posterior. Finally, the posterior are compared to measured values for the stability boundary and system parameters to evaluate the approach. Based on experimental observations, the advantages and disadvantages of using a physics-guided model are discussed.

Cornelius, Aaron↗
NASA NTRS1980

FBI fingerprint identification automation study: AIDS 3 evaluation report. Volume 9: Functional requirements

The current system and subsystem used by the Identification Division are described. System constraints that dictate the system environment are discussed and boundaries within which solutions must be found are described. The functional requirements were related to the performance requirements. These performance requirements were then related to their applicable subsystems. The flow of data, documents, or other pieces of information from one subsystem to another or from the external world into the identification system is described. Requirements and design standards for a computer based system are presented.

Source record↗