Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Band gap”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

A theoretical study of heterojunction and graded band gap type solar cells

The work performed concentrated on including multisun effects, high temperature effects, and electron irradiation effects into the computer analysis program for heterojunction and graded bandgap solar cells. These objectives were accomplished and the program is now available for such calculations.

Chiang, J. P. C.↗
NASA NTRS1980

Determination of deep level capture cross sections in wide band-gap semiconductors by means of an electron beam

The paper presents a general theory for the determination of the short circuit current generated by a sinusoidally amplitude-modulated electron beam in the presence of recombination centers with an arbitrary number of charge states. It is shown that a measurement of the coherent phase shift with respect to the incident beam as a function of the modulation frequency of the beam ascertains the magnitudes of electron and hole capture cross sections. The surface exposed to the electron beam must have a negligible surface recombination velocity for the measurements to be unambiguous.

Von Roos, O.↗
NASA NTRS1991

Improvement of program to calculate electronic properties of narrow band gap materials

The program was improved by reprogramming it so it will run on both a SUN and a VAX. Also it is easily transportable as it is on a disk for use on a SUN. A computer literature search resulted in some improved parameters for Hg(1-x)Cd(x)Te and a table of parameters for Hg(1-x)Zn(x)Te. The effects of neutral defects were added to the program, and it was found, as expected, that they contribute very little to the mobility at temperatures of interest. The effect were added of varying the following parameters: dielectric constants, screening parameters, disorder energies, donor and acceptor concentrations, momentum matrix element, different expressions for energy gap, and transverse effective charge.

Patterson, James D.↗
NASA NTRS1992

Further improvements in program to calculate electronic properties of narrow band gap materials

The tasks that we have accomplished are discussed. An extra task was a calculation comparing electron mobilities in Mercury Manganese Telluride with Mercury Cadmium Telluride given in 1H. We then list the reports and papers produced and follow that with either abstracts or the papers themselves. In one key paper we obtain good results between experiment and theory in Mercury Zinc Telluride and also find it typically has mobilities competitive with Mercury Cadmium Telluride. In the Appendix we have a relatively complete set of references.

Patterson, James D.↗
NASA NTRS1990

Dissociation of O(2-)2 defects into paramagnetic O(-) in wide band-gap insulators - A magnetic susceptibility study of magnesium oxide

The magnetic susceptibility of single-crystal MgO has been measured in the temperature range 300-1000 K, using a Faraday balance. The high-purity crystal (less than 100 ppm transition metals), grown from the melt in a H2O-containing atmosphere, was found to be paramagnetic due to the presence of defects on the O(2-) sublattice. The defects derive from OH(-) introduced into the MgO matrix by the dissolution of traces of H2O during crystal growth. The OH(-) converts into O(2-)2 and H2. Each O(2-)2 represents two coupled, spin-paired O(-) states. The observed strongly temperature-dependent paramagnetism can be described by three contributions that overlay the intrinsic diamagnetism of MgO and arise from the low level of transition-metal impurities, O(-) generated by 0(2-)2 dissociation, and O(-) states trapped by quenching from high temperatures from previous experiments.

Batllo, F.↗
NASA NTRS1993

Below band-gap laser ablation of diamond for transmission electron microscopy

A 248 nm excimer laser was used to thin naturally occurring type 1a diamond substrates at normal and glancing (22 deg) incidence. Perforation of a 250-micron-thick substrate was achieved in about 15 min at normal incidence. While the substrate thinned at glancing incidence was found to have large electron-transparent areas, that thinned at normal incidence required additional argon-ion milling to achieve electron transparency. X-ray photoelectron spectroscopy of the back surface of the diamond failed to detect any graphite or glassy carbon, confirming that damage due to laser ablation occurs only at the incident surface. Samples prepared using this technique imaged in the transmission electron microscope were observed to have retained the nitrogen platelets characteristic of such type 1a diamonds.

George, T.↗
NASA NTRS1993

Growth experiment of narrow band-gap semiconductor PbSnTe single crystals in space (M-1)

An experiment on crystal growth of Pb(1-x)Sn(x)Te in microgravity is planned. This material is an alloy of the compound semiconductors PbTe and SnTe. It is a promising material for infrared diode lasers and detectors in the wavelength region between 6 and 30 micron. Since the electrical properties of Pb(1-x)Sn(x)Te depend greatly on the Pb/Sn ratio and crystalline defects as well as impurity concentration, homogeneous, defect-free, high-quality crystals are anticipated. Although many growth methods, such as the pulling method, the Bridgman method, the vapor growth method, etc., have been applied to the growth of Pb(1-x)Sn(x)Te, large, homogeneous, low-defect-density crystals have not yet been grown on Earth. The unsuccessful results were caused by buoyancy-driven convection in the fluids induced by the specific gravity difference between heated and cooled fluids on Earth. A crystal is grown by cooling the melt from one end of the ampoule. In crystal growth from the melt, about 30 percent of the SnTe in the melt is rejected at the solid-liquid interface during solidification. On Earth, the rejected SnTe is completely mixed with the remaining melt by convection in the melt. Therefore, SnTe concentration in the melt, and accordingly in the crystal, increases as the crystal grows. In the microgravity environment, buoyancy-driven convection is suppressed because the specific gravity difference is negligible. In that case, the rejected SnTe remains at the solid-liquid interface and its concentration increases only at the interface. If the growth rate is higher than the PbTe-SnTe interdiffusion rate, the amount of SnTe which diffuses from the interface into the melt increases as SnTe piles up at the interface, and finally it balances the amount of rejected SnTe during solidification, resulting in steady-state SnTe transportation at the interface. By using this principle, compositionally homogeneous crystals can be grown. Furthermore, low-defect-density crystals will be grown in microgravity, because convection causes crystalline defects by mising hot and cold fluids and generating temperature fluctuations in them.

Yamada, Tomoaki↗
NASA NTRS1996

The growth of low band-gap InAs on (111)B GaAs substrates

Growth on the (111)B orientation exhibits a number of advantageous properties as compared to the (100) during the early stages of strained-layer epitaxy. In accordance with a developing model of nucleation and growth, we have deposited thin (60 A - 2500 A), fully relaxed InAs films on (111)B GaAs substrates. Although thicker InAs films are subject to the formation of twin defects common to epitaxy on the (111)B orientation, appropriate control of the growth parameters can greatly minimize their density. Using this knowledge base, InAs films up to 2 microns in thickness with improved morphology and structural quality have been grown on (111)B GaAs substrates.

Welser, Roger E.↗
NASA NTRS1995

The Growth of Low Band-Gap InAs on (111)B GaAs Substrates

Growth on the (111)B orientation exhibits a number of advantageous properties as compared to the (100) during the early stages of strained-layer epitaxy. In accordance with a developing model of nucleation and growth, we have deposited thin (60 A - 2500 A), fully relaxed InAs films on (111)B GaAs substrates. Although thicker InAs films are subject to the formation of twin defects common to epitaxy on the (111)B orientation, appropriate control of the growth parameters can greatly minimize their density. Using this knowledge base, InAs films up to 2 microns in thickness with improved morphology and structural quality have been grown on (111)B GaAs substrates.

Weiser, R. E.↗
NASA NTRS1997

Multi Band Gap High Efficiency Converter (Rainbow)

This papter reprots on the reexamination of the spectrally split, individually matched cell approach using modern-day optics and lightweight structures.

Converter Solar Array Efficiency Solar Spectrum↗
NASA NTRS1993

Below Band-Gap Laser Ablation of Diamond for Transmission Electron Microscopy

A 248-nm excimer laser was used to thin naturally occurring type 1a diamond substrates at normal and glancing (22 deg) incidence. Perforation of a 250 micron thick substrate was achieved in about 15 minutes at normal incidence. Whilst the substrate thinned at glancing incidence was found to have large electron-transparent areas, that thinned at normal incidence required additional argon milling to achieve electron transparency. X-ray photoelectron spectroscopy of the back surface of the diamond failed to detect any graphite or glassy carbon, confirming that damage due to laser ablation occurs only at the incident surface. Samples prepared using this technique imaged in the transmission electron microscope were observed to have retained the nitrogen platelets

Posthill, J. B.↗
NASA NTRS2019

Summary of the Advanced Supersonic Parachute Inflation Research Experiment (ASPIRE) Sounding Rocket Tests with a Disk-Gap-Band Parachute

This paper will present an overview of all three ASPIRE flights. First, the Test Architecture that was used for all three ASPIRE flights will be presented. This will be broken down into an explanation of the Concept of Operations (CONOPS),the parachute test articles, the data sources used, and the process that was used to reconstruct the flight trajectories and parachute performance. Next, the performance and results for all three ASPIRE flights will be presented in the order of the phases of flight. Lastly this paper will discuss the Conclusions and Lessons Learned from those results and from the ASPIRE project as a whole.

Tynis, Jake A.↗