Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BEAMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Calibration of the analog beam-signal hardware for the credited engineered beam power limit system at the Proton Power Upgrade Project at the Spallation Neutron Source

A programmable signal processor-based credited safety control that calculates pulsed beam power based on beam kinetic energy and charge was designed as part of the Proton Power Upgrade (PPU) project at the Spallation Neutron Source (SNS). The system must reliably shut off the beam if the average power exceeds 2.145 MW averaging over 60 seconds. System calibration requires pedigree in measurements, calibration setup, and calculations. This paper discusses the calibration of the analog beam signal components up to and including the Analog Digital Convertors (ADCs) for implementation into the Safety Programmable Logic Controllers (PLCs) and Field Programmable Gate Arrays (FPGAs).

Bobrek, Miljko↗
DOE OSTI2025

Image mapping for multiple charge state beams using a beam induced fluorescence profile monitors

Work continues on a minimally invasive, nitrogen fluorescence gas sheet at the Facility for Rare Isotope Beams (FRIB). A low density gas sheet may be used to observe the 2D transverse beam profile of high intensity, multiple charge state beams with minimal interference. Spatially and temporally correlated profiles are of particular interest in locations where there is significant charge state spread, such as the FRIB linac folding segments. A low-density gas sheet measurement system offers advantages for gas handling in nitrogen sensitive areas, however signal intensity is significantly lower than techniques using higher density gas sheets and jets. This work discusses measurement considerations for photon distributions generated by several spatially separated interaction points and design considerations for a high-sensitivity optics system for handling the expected low signal intensity.

Accelerator Physics↗
DOE OSTI2021

Beam power scale-up in micro-electromechanical systems based multi-beam ion accelerators

We report on the development of multi-beam RF linear ion accelerators that are formed from stacks of low cost wafers and describe the status of beam power scale-up using an array of 120 beams. The total argon ion current extracted from the 120-beamlet extraction column was 0.5 mA. The measured energy gain in each RF gap reached as high as 7.25 keV. We present a path of using this technology to achieve ion currents >1 mA and ion energies >100 keV for applications in materials processing.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Beam particle identification and tagging of incompletely stripped heavy beams with HEIST

A challenge preventing successful inverse kinematics measurements with heavy nuclei that are not fully stripped is identifying and tagging the beam particles. For this purpose, the HEavy ISotope Tagger (HEIST) has been developed. HEIST utilizes two micro-channel plate timing detectors to measure the time-of-flight, a multi-sampling ion chamber to measure energy loss, and a high-purity germanium detector to identify isomer decays and calibrate the isotope identification system. HEIST has successfully identified 198 Pb and other nearby nuclei at energies of about 75 MeV/A. In the experiment discussed, a typical cut containing 89% of all 198 Pb 80+ in the beam had a purity of 86%. We examine the issues of charge state contamination. Here, the observed charge state populations of these ions are presented and, using an adjusted beam energy, are well described by the charge state model GLOBAL.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Beam-pointing verification using x-ray pinhole cameras on the 60-beam OMEGA laser

On the OMEGA laser system, the beam-pointing accuracy is verified by irradiating a 4 mm diameter Au-coated spherical target with ~23 kJ of laser energy. Up to ten x-ray pinhole cameras record the x-ray emission from all 60-beam spots. A new set of algorithms has been developed to improve the accuracy of the pointing evaluation. An updated edge-finding procedure allows one to infer the center of the sphere with subpixel accuracy. A new approach was introduced to back-propagate the pixel locations on the 2D image to the 3D surface of the sphere. Furthermore, a fast Fourier transform-based de-noising method significantly improves the signal-to-noise of the data. Based on the beam-pointing analysis, hard-sphere calculations of the laser-drive illumination uniformity on the target surface and the decomposition of the illumination distribution into lower order modes (1–10) are evaluated.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Experimental investigation of beam-ion losses induced by magnetic perturbations using the light ion beam probe technique in the ASDEX Upgrade tokamak

The impact of externally applied magnetic perturbations (MPs) on fast-ion losses has been investigated by means of the light ion beam probe (LIBP) technique in the ASDEX Upgrade tokamak. The LIBP technique allows to experimentally infer the fast-ion orbit displacement induced by MPs via first-orbit losses using scintillator based fast-ion loss detector (FILD) measurements. The fast-ion orbit displacement against different applied MP spectra has been studied. These shots were conducted in ELM mitigated H-mode plasmas. A rigid rotation of the MP coils was applied with a frequency of 1 Hz, with an n = 2 configuration and changing the differential phase between the upper and lower set of coils (ΔΦ ul ) on a shot-to-shot basis. Beam sources Q7 (tangential) and Q8 (radial) were used to probe different fast-ion orbits with FILD1. The measured fast-ion orbit displacement ranges from 3 to 20 mm approximately, and no qualitative difference is observed between ions from beam sources Q7 and Q8. The minimum is found for a ΔΦ ul ~ 50°, which is shifted with respect to the minimum of the plasma boundary displacement, found at ΔΦ ul ~ 0°. A first attempt to validate the orbit following code ASCOT—including the plasma response calculated with the MARS-F code—against these experimental measurements is performed. Finally, while the dependence of the first-orbit fast-ion displacement with ΔΦ ul does not match the experimental measurements, these simulations do capture other features such as the order of magnitude of the orbit displacement and the importance of the toroidal spectrum of the applied perturbation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Measurement and modeling of beam transport in the FODO line of the Spallation Neutron Source Beam Test Facility

Ongoing studies at the Spallation Neutron Source (SNS) Beam Test Facility (BTF) seek to understand and model bunch dynamics in a high-power LINAC front-end. The BTF has recently been upgraded with a reconfiguration from a U-shaped line to a Straight line. We report the current state of model benchmarking, with a focus on RMS beam sizes within the FODO line. The beam measurement is obtained via three camera/screen pairs in the FODO line. This presentation discusses the methodology and results of this measurement.

Thompson, Trent↗
DOE OSTI2021

An examination of different representations of the electrostatic field and potential of an intense relativistic electron beam in a cylindrical conductor and their implications on foil focusing of an elliptical beam

Knowledge of the electrostatic field and potential of an intense relativistic electron beam (IREB) in a cylindrical conductor is essential for understanding the transport of IREBs including the interaction of a grounded conducting foil with the beam. Different representations of the electrostatic field or potential exist in the literature. The different representations are compared and an extension to foil focusing of elliptical beams is discussed.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Beam Dynamics Simulations of Transient Beam Loading Effects in the 10GeV EIC Electron Storage Ring

We report on beam dynamics studies of transient beam loading effects in the 10 GeV EIC electron storage ring [1]. The studies are carried out with time-dependent Vlasov-Fokker-Planck simulations performed with the parallel, particle tracking code SPACE [2], which allows to follow self-consistently the dynamics of h bunches, where h in the number of RF buckets, in arbitrary multi-bunch configurations. The specific goal of the numerical simulations is to determine stable RF cavity settings under heavy beam loading. We also study the option to operate with a passive, third-harmonic cavity (3HC) system for bunch lengthening, addressing both stability and the performance limitation due to a gap in the uniform filling pattern for ion clearing.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Comments on the paper “Eliminating beam-induced depolarizing effects in the hydrogen jet target for high-precision proton beam polarimetry at the Electron-Ion Collider” (Part I)

A critical review of the methodology used in F. Rathmann et al., Phys. Rev. Accel. Beams 29, 021001 (2026), to evaluate beam-induced depolarization of the Atomic Polarized Hydrogen Gas Jet (HJET) target at the Electron–Ion Collider (EIC) is presented. It is shown that several key assumptions underlying that analysis—including the introduction of a photon emission threshold, the application of Fermi’s Golden Rule to coherent hyperfine transitions, the interpretation of power broadening as a physical linewidth increase, and the treatment of spatial magnetic fields—are either incorrect or internally inconsistent. As a consequence, the predicted large depolarization effects are demonstrated to be artifacts of the adopted methodology rather than genuine physical phenomena. A consistent quantum-mechanical treatment based on the time-dependent Schrödinger equation shows that beam-induced depolarization probabilities at the EIC are negligibly small.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Beam-beam effects in the Super Proton-Proton Collider

The Supper Proton-Proton Collider is a next-generation hadron collider that is now being designed. A baseline design aims for a peak luminosity of about 1*10^35 cm^-2 s^-1. The focus of this article is the effect of beam-beam interactions which are expected to strongly influence stability in the beams. We start with a discussion of a scheme to generate the crossing angles at the interaction points while also correcting the dispersion thus created. The optics constraints on the achievable \b{eta}* were studied. Weak-strong simulations were performed to study single particle dynamics via tune footprints, frequency map analysis and dynamic aperture calculations. The long-range interactions with the smallest separations are shown to determine the dynamic aperture. Empirical scaling laws for the dependence of the dynamic aperture on the transverse separations and on the number of long-range interactions are found. A tune scan shows several alternative working points with slightly better dynamic aperture than the baseline choice. Finally an option to significantly increase the dynamic aperture by increasing the crossing angle for different choices of \b{eta}* was studied.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

A BEAM SCREEN TO PREPARE THE RHIC VACUUM CHAMBER FOR EIC HADRON BEAMS: CONCEPTUAL DESIGN AND REQUIREMENTS

The Electron Ion Collider (EIC) Hadron Storage Ring (HSR) will use the existing Relativistic Heavy Ion Collider storage rings, including the superconducting magnet arcs [1]. The vacuum chambers in the superconducting magnets and the cold mass interconnects were not designed for EIC beams and so must be updated to reduce resistive-wall heating and to suppress e-clouds. To do so without compromising the EIC luminosity goal, a stainless steel beam screen with colaminated copper and a thin layer of amorphous carbon will be installed. This paper describes the main requirements that our solution for the hadron ring vacuum chamber needs to satisfy, including impedance, aperture limitations, vacuum, thermal and structural stability, mechanical design, installation and operation. The conceptual design of the beam screen currently under development is introduced.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

A rotor-based multileaf collimator for beam shaping

We introduce a new style of multileaf collimator which employs rotors with angularly dependent radius to control the masking aperture: a rotor-based multileaf collimator (RMLC). Using a padlock-inspired mechanism, a single motor can set dozens of rotors, i.e. leaves, independently. This is especially important for an ultra-high vacuum (UHV) compatible MLC, since this reduces the number of actuators and vacuum feedthroughs required by more than an order of magnitude. This new RMLC will complement previous work employing a UHV compatible MLC with an emittance exchange beamline to create arbitrarily shaped beams on demand. A feed-forward control system which abstracts away the complexity of the RMLC operation, and is adaptable to real beamline conditions, is discussed and demonstrated in simulation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Interferometric bunch length measurements of 3 MeV picocoulomb electron beams

We report picosecond bunch length measurements using an interferometric method for a 3 MeV electron beam having bunch charge ranging from 1 to 14 pC. The method senses the single-cycle sub-terahertz (THz) pulse emitted by each electron bunch as coherent transition radiation which, in turn, is analyzed using a Michelson-type interferometer, forming an interferogram that is then processed to yield the nominal electron bunch length. This sub-THz coherent radiation intensity was measured using a quasi-optical detector (QOD) operated at room temperature. This experiment was quite challenging since the divergence angle of the sub-THz pulse emitted by the low-energy electron bunch exceeds ±10°, and its pulse energy at the entrance to the detector was as low as 100 pJ. When compared to a conventional helium-cooled silicon composite bolometer designed for frequencies above 0.5 THz, the QOD provided much better signal-to-noise ratio in the ~80 GHz frequency range, which was critical for the successful measurement of the bunch length.

36 MATERIALS SCIENCE↗
DOE OSTI2022

GaAs Substrate Recycling Using in-situ Deposited NaCl Layers via Molecular Beam Epitaxy

This work presents an alternative method to conventional III-V substrate recycling methods via growth of NaCl on nearly-lattice matched GaAs (001) substrates. Reflection high energy electron diffraction and transmission electron microscopy confirm an epitaxial relationship between the NaCl layers and the underlying GaAs. If the sample is heated too much prior to GaAs deposition, the NaCl fully desorbs from the surface. The quality of the deposition of GaAs on NaCl ranges from amorphous at low temperature to polycrystalline at intermediate temperatures. Exposure to electron beams during growth results in larger and (001) textured grains. The substrate is separated from the GaAs film in seconds via submersion in water, revealing a substrate surface comparable to the original.

electron beams↗
DOE OSTI2022

Synthesis of antiferromagnetic Weyl semimetal Mn 3 Ge on insulating substrates by electron beam assisted molecular beam epitaxy

The antiferromagnetic kagome semimetals Mn 3 X (X = Ge, Sn, Ga) are of great interest due to properties arising from their Berry curvature, such as large anomalous Nernst and anomalous Hall coefficients, and spin to charge conversion efficiencies at ambient temperatures. However, the synthesis of epitaxial thin films of Mn 3 Ge in the desired hexagonal phase has been challenging because they do not wet insulating substrates, necessitating the use of a metallic buffer layer. Furthermore, a ferrimagnetic tetragonal phase also forms readily under typical growth conditions, interfering with hexagonal phase properties. We have synthesized atomically smooth and continuous epitaxial thin films of hexagonal Mn 3 Ge directly on insulating LaAlO 3 (111) substrates using electron beam assisted molecular beam epitaxy, using a three-step process that mitigates the formation of the tetragonal phase. The anomalous Nernst coefficient is found to be more than six times larger in our films than in sputtered thin films of Mn 3 Ge and significantly larger than that of Fe. Our approach can be used to grow thin layers of kagome materials, without interference from a buffer layer in transport properties, and may be applicable to a broader range of materials with large surface energies that do not grow readily on insulating substrates.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Measurement of Beam-Correlated Background Neutrons from the Fermilab Booster Neutrino Beam in ANNIE Phase-I

The Accelerator Neutrino Neutron Interaction Experiment (ANNIE) aims to make a unique measurement of neutron yield from neutrino-nucleus interactions and to perform R&D for the next generation of water-based neutrino detectors. In this paper, we characterize beam-induced neutron backgrounds in the experimental hall at Fermi National Accelerator Laboratory. It is shown that the background levels are sufficiently low to allow the next stage of the experiment to proceed. These measurements are relevant to other Booster Neutrino Beam (BNB) [1] experiments located adjacent to ANNIE Hall, where dirt neutrons and sky-shine could present similar backgrounds.

Particle identification methods↗
DOE OSTI2021

Test beam study of SiPM-on-tile configurations

Light yield and spatial uniformity for a large variety of configurations of scintillator tiles were studied. The light from each scintillator was collected by a Silicon Photomultiplier (SiPM) directly viewing the produced scintillation light (SiPM-on-tile technique). The varied parameters included tile transverse size, tile thickness, tile wrapping material, scintillator composition, and SiPM model. Furthermore, these studies were performed using 120 GeV protons at the Fermilab Test Beam Facility. External tracking allowed the position of each proton penetrating a tile to be measured. The results were compared to a GEANT4 simulation of each configuration of scinitillator, wrapping, and SiPM.

47 OTHER INSTRUMENTATION↗