Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Additives

The chemistry of lubricant additives is discussed to show what the additives are chemically and what functions they perform in the lubrication of various kinds of equipment. Current theories regarding the mode of action of lubricant additives are presented. The additive groups discussed include the following: (1) detergents and dispersants, (2) corrosion inhibitors, (3) antioxidants, (4) viscosity index improvers, (5) pour point depressants, and (6) antifouling agents.

Smalheer, C. V.↗
NASA NTRS1972

Tabulated pressure measurements of a NASA supercritical-wing research airplane model with and without fuselage area-rule additions at Mach 0.25 to 1.00

Basic pressure measurements were made on a 0.087-scale model of a supercritical wing research airplane in the Langley 8 foot transonic pressure tunnel at Mach numbers from 0.25 to 1.00 to determine the effects on the local aerodynamic loads over the wing and rear fuselage of area-rule additions to the sides of the fuselage. In addition, pressure measurements over the surface of the area-rule additions themselves were obtained at angles of sideslip of approximately - 5 deg, 0 deg, and 5 deg to aid in the structural design of the additions. Except for representative figures, results are presented in tabular form without analysis.

Harris, C. D.↗
NASA NTRS1978

Effect of a chromium-containing fuel additive on hot corrosion

Four cast superalloys (one cobalt-base and three nickel-base) were tested at 900 C for 100 h in Mach 0.3 combustion gases. 5 ppm of synthetic sea salt were added to the gases in the combustion chamber. Several types of thermal cycle and washing procedures were employed. Similar tests were made with the addition of 300 ppm of a chromium-containing fuel additive. In both sets of tests the extent of hot corrosion was evaluated by specific weight change and metal recession. In general, the chromium additive in the fuel reduced the extent of hot (salt) corrosion but did not eliminate it. The percentage reduction of hot corrosion attack was similar for all four alloys. As great a reduction of hot corrosion was achieved by reducing the number of thermal cycles during the test from 100 to 5 or 6. The effect of washing the alloys every ten cycles as opposed to the end of the test was erratic; some alloys were attacked slightly more, others somewhat less. A NiCrAlY coating was found to be more effective in reducing hot corrosion than either the fuel additive or the washing schedule.

Lowell, C. E.↗
NASA NTRS1982

Influence of mineral oil and additives on microhardness and surface chemistry of magnesium oxide (001) surface

X-ray photoelectron spectroscopy analyses and hardness experiments were conducted with cleaved magnesium oxide /001/ surfaces. The magnesium oxide bulk crystals were cleaved into specimens along the /001/ surface, and indentations were made on the cleaved surface in laboratory air, in nitrogen gas, or in degassed mineral oil with and without an additive while not exposing specimen surface to any other environment. The various additives examined contained sulfur, phosphorus, chlorine, or oleic acid. The sulfur-containing additive exhibited the highest hardness and smallest dislocation patterns evidencing plastic deformation; the chlorine-containing additive exhibited the lowest hardness and largest dislocation patterns evidencing plastic deformation. Hydrocarbon and chloride (MgCl2) films formed on the magnesium oxide surface. A chloride film was responsible for the lowest measured hardness.

Miyoshi, K.↗
NASA NTRS1982

Effects of various additives on sintering of aluminum nitride

Effects of thirty additives on sintering A/N were investigated. The addition of alkali earth oxides and rare earth oxides gave fully densified aluminum nitride. This is due to the formation of nitrogen-containing aluminate liquid in the system aluminum nitride-alkali earth oxides or rare earth oxides. Microstructural studies of the sintered specimens with the above two types of additives suggested that the densification was due to the liquid phase sintering. Additions of silicon compounds resulted in poor densification by the formation of highly refractory compounds such as A/N polytypes.

Komeya, K.↗
NASA NTRS1982

Anti-misting additives for jet fuels

The ignition characteristics of sprays, created by wind shear action, of Jet-A fuel containing polyisobutylene additives wee examined over ranges of air velocities from 45 to 90 m/s and of fuel/air mass ratios of 0.20 to 8.0. Ignition was by calibrated sparks of energies up to about 0.5 J and by a butane/oxygen flame at 165 J/s. The polymeric additives studied included the grades L80, L160, and L200 from Exxon Chemical and B200 and B230 from BASF. The ignition suppression ability of the additives, as well as their observed anti-misting (AM) behavior, ranked exactly as their molecular weights (viscosity average, M sub v) with 400-500 ppm of L80 (M sub v = 0.68 x 1,000,000) being required to suppress ignition of a spray at 51 m/s, 1.8 fuel/air mass ratio, by a 0.55 J spark while only 10 ppm of B230 (M sub v = 7.37 x 1,000,000) was required for the same conditions. The additive concentrations (L160) required for ignition suppression increased with increasing air velocity and with increasing fuel/air ratio.

Grens, E. A., II↗
NASA NTRS1987

Slip casting and extruding shapes of rhemium with metal oxide additives. Part 2: Development of grain stabilized rhenium parts for resistojets

The adaptation of the powdered particle process used for pure metal oxides to the coprocessing of rhenium oxides suitable to produce pure miniature resistojet hardware has been successful. Both slip casting and extrusion processes were used. The metal oxide ZrO2 was stabilized into the cubic phase with Y2O3, for use as a potentially grain stabilizing additive to rhenium. Straight meter long tubing in two sizes are reported. Tubing suitable for resistojet ohmic heater use of fully fired dimensions of nominally 3.8 mm o.d. x 2.2 mm i.d.. and 1.26 mm o.d. x .45 mm i.d. with 0, 0.5, 1.0 and 5.0% zirconia additives were produced for further study. Photomicrographs of these are discussed. The addition of the metal oxide zirconia to rhenium resulted in more dense and less porous parts. The additions of phase stabilized zirconia most likely act as a sintering aid. Tubes of varying diameter were slip cast which were representative of miniature pressure cases.

Barr, Francis A.↗
NASA NTRS1990

Environmental projects, volume 11. Environmental assessment: Addition to operations building, Mars site

An Environmental Assessment was performed of the proposed addition to building G-86 at the Mars Site, which will provide space for new electronic equipment to consolidate the Deep Space Network (DSN) support facilities from other Goldstone Deep Space Communication Complex (GDSCC) sites at the Mars Site, and will include a fifth telemetry and command group with its associated link monitor, control processor, and operator consoles. The addition of these facilities will increase the capability of the DSN to support future sophisticated NASA spacecraft missions such as the International Solar and Terrestrial Physics (ISTP) Program. The planned construction of this building addition requires an Environmental Assessment (EA) document that records the existing environmental conditions at the Mars Site, that analyzes the environmental effects that possibly could be expected from the construction and use of the new building addition, and that recommends measures to be taken to mitigate any possible deleterious environmental effects.

Source record↗
NASA NTRS1989

Microstructure and tensile properties of Fe-40 at. pct Al alloys with C, Zr, Hf, and B additions

The influence of small additions of C, Zr, and Hf, alone or in combination with B, on the microstructure and tensile behavior of substoichiometric FeAl was investigated. Tensile properties were determined from 300 to 1100 K on powder which was consolidated by hot extrusion. All materials possessed some ductility at room temperature, although ternary additions generally reduced ductility compared to the binary alloy. Adding B to the C- and Zr-containing alloys changed the fracture mode from intergranular to transgranular and restored the ductility to approximately 5 percent elongation. Additions of Zr and Hf increased strength up to about 900 K. Fe6Al6Zr and Fe6Al6Hf precipitates, both with identical body-centered tetragonal structures, were identified as the principal second phase in these alloys. Strength decreased steadily as temperature increased above 700 K, as diffusion-assisted mechanisms became operative. Although all alloys had similar strengths at 1100 K, Hf additions significantly improved high-temperature ductility by suppressing cavitation.

Gaydosh, D. J.↗
NASA NTRS1990

Evaluation of two bisimide additives in LARC-TPI adhesive

The processability of aromatic polyimides can be improved by the addition of bis (amide) acids or bisimides to LARC-TPI. These low molecular weight additives apparently lower the melt viscosity of aromatic polyimides without affecting the glass transition temperature. Well-consolidated, fiber reinforced composites were fabricated using this technology. LARC-TPI can be processed as a thermoplastic polyimide to form high strength bonds, however, this is generally accomplished by processing at relatively high bonding pressures. An adhesive investigation is presented on the effects of two bisimide additives to LARC-TPI in an attempt to improve the bonding process by lowering the viscosity of the material to achieve improved bond strength properties. Apparently, the high flow which is exhibited by the additives when they melt, tended to be masked by the more viscous LARC-TPI.

Progar, Donald J.↗
NASA NTRS1993

An expert system shell for inferring vegetation characteristics: Interface for the addition of techniques (Task H)

All the NASA VEGetation Workbench (VEG) goals except the Learning System provide the scientist with several different techniques. When VEG is run, rules assist the scientist in selecting the best of the available techniques to apply to the sample of cover type data being studied. The techniques are stored in the VEG knowledge base. The design and implementation of an interface that allows the scientist to add new techniques to VEG without assistance from the developer were completed. A new interface that enables the scientist to add techniques to VEG without assistance from the developer was designed and implemented. This interface does not require the scientist to have a thorough knowledge of Knowledge Engineering Environment (KEE) by Intellicorp or a detailed knowledge of the structure of VEG. The interface prompts the scientist to enter the required information about the new technique. It prompts the scientist to enter the required Common Lisp functions for executing the technique and the left hand side of the rule that causes the technique to be selected. A template for each function and rule and detailed instructions about the arguments of the functions, the values they should return, and the format of the rule are displayed. Checks are made to ensure that the required data were entered, the functions compiled correctly, and the rule parsed correctly before the new technique is stored. The additional techniques are stored separately from the VEG knowledge base. When the VEG knowledge base is loaded, the additional techniques are not normally loaded. The interface allows the scientist the option of adding all the previously defined new techniques before running VEG. When the techniques are added, the required units to store the additional techniques are created automatically in the correct places in the VEG knowledge base. The methods file containing the functions required by the additional techniques is loaded. New rule units are created to store the new rules. The interface that allow the scientist to select which techniques to use is updated automatically to include the new techniques. Task H was completed. The interface that allows the scientist to add techniques to VEG was implemented and comprehensively tested. The Common Lisp code for the Add Techniques system is listed in Appendix A.

Harrison, P. Ann↗
NASA NTRS1947

Formulas for additional mass corrections to the moments of inertia of airplanes

Formulas are presented for the calculation of the additional mass corrections to the moments of inertia of airplanes. These formulas are of particular value in converting the virtual moments of inertia of airplanes or models experimentally determined in air to the true moments of inertia. A correlation of additional moments of inertia calculated by these formulas with experimental additional moments of inertia obtained from vacuum chamber tests of 40 spin-tunnel models indicates that formulas give satisfactory estimations of the additional moments of inertia.

MOMENTS OF INERTIA↗
NASA NTRS1996

Methods of Measuring Vapor Pressures of Lubricants With Their Additives Using TGA and/or Microbalances

The life of a space system may be critically dependent on the lubrication of some of its moving parts. The vapor pressure, the quantity of the available lubricant, the temperature and the exhaust venting conductance passage are important considerations in the selection and application of a lubricant. In addition, the oil additives employed to provide certain properties of low friction, surface tension, antioxidant and load bearing characteristics, are also very important and need to be known with regard to their amounts and vapor pressures. This paper reports on the measurements and analyses carried out to obtain those parameters for two often employed lubricants, the Apiezon(TM)-C and the Krytox(TM) AB. The measurements were made employing an electronic microbalance and a thermogravimetric analyzer (TGA) modified to operate in a vacuum. The results have been compared to other data on these oils when available. The identification of the mass fractions of the additives in the oil and their vapor pressures as a function of the temperature were carried out. These may be used to estimate the lubricant life given its quantity and the system vent exhaust conductance. It was found that the Apiezon(TM)-C has three main components with different rates of evaporation while the Krytox(TM) did not indicate any measurable additive.

Scialdone, John J.↗
NASA NTRS2002

Additive Effects on Si3n4 Oxidation/Volatilization in Water Vapor

Two commercially available additive-containing silicon nitride materials were exposed in four environments which range in severity from dry oxygen at 1 atm pressure, and low gas velocity to an actual turbine engine. Oxidation and volatilization kinetics were monitored at temperatures ranging from 1066 to 1400 C. The main purpose of this paper is to examine the surface oxide morphology resulting from the exposures. It was found that the material surface was enriched in rare earth silicate phases in combustion environments when compared to the oxides formed on materials exposed in dry oxygen. However, the in situ formation of rare earth disilicate phases offered little additional protection from the volatilization of silica observed in combustion environments. It was concluded that externally applied environmental barrier coatings are needed to protect additive-containing silicon nitride materials from volatilization reactions in combustion environments. Introduction Si3N4 is proposed for use as components, such as vanes, in turbine applications. Tens of thousands of hours of life are needed for both land-based turbines and aeropropulsion applications. Additive-containing SisN4 materials are

Opila, Elizabeth J.↗
NASA NTRS1961

Wind-Tunnel Investigation of the Effects of Wing Bodies, Fences, Flaps, and a Fuselage Addition on the Wing Buffet Response of a Transonic-Transport Model

The experimental wing buffet response of a transport-type airplane model with and without wing bodies, fences, flaps, and a fuselage addition has been investigated at Mach numbers from 0.20 to 1.03. The wing had NACA 64A-series airfoil sections inclined 5 degrees to the free-stream direction. The quarter-chord line of the wing was swept back 45 degrees, the aspect ratio was 7, the taper ratio was 0.3, and the thickness ratio varied from 0.115 at the root to 0.074 at the midsemispan and was constant from that station to the tip. The wing was twisted and cambered for a design lift coefficient of 0.3. The results of the investigation indicated that a marked reduction of buffet intensity and a delay of buffet onset at transonic speeds were achieved by the addition to the wing of special bodies designed to reduce shock-induced separation. The further addition of wing fences and wing trailing-edge flaps deflected 30 degrees increased the lift coefficients at which low-speed stall buffeting occurred. An addition to the fuselage near the upper forward portion produced no consistent change in the buffet characteristics.

Cornette, Elden S.↗
NASA NTRS2003

Creep Resistance of ZrO2 Ceramic Improved by the Addition of a Small Amount of Er2O3

Zirconia (ZrO2) has great technological importance in structural, electrical, and chemical applications. It is the crucial component for state-of-the art thermal barrier coatings and an enabling component as a solid electrolyte for solid-oxide fuel cell systems. Pure ZrO2 is of limited use for industrial applications because of the phase transformations that occur. Upon the addition of stabilizers, cubic (c-ZrO2) and tetragonal (t-ZrO2) forms can be preserved. It is the stabilized and partially stabilized forms of zirconia that function as thermal barrier coatings, solid electrolytes, and oxygen sensors and that have numerous applications in the electrochemical industry. The cubic form of ZrO2 is typically stabilized through Y2O3 additions. However, Y2O3-stabilized zirconia is susceptible to deformation at high temperatures (greater than 900 C) because of the large number of slip systems and the high oxygen diffusion rates, which result in high creep rates at high temperatures. Successful use of ZrO2 at high temperatures requires that new dopant additives be found that will retain or enhance the desirable properties of cubic ZrO2 and yet produce a material with lower creep rates. At the NASA Glenn Research Center, erbium oxide (Er2O3) was identified as a promising dopant for improving the creep resistance of. ZrO2. The selection of Er2O3 was based on the strong interactions of point defects and dislocations. Single crystals of 5 mol% Er2O3- doped ZrO2 rods (4 mm in diameter) and monofilaments (200 to 300 mm in diameter and 30 cm long) were grown using the laser-heated float zone technique, and their creep behavior was measured as a function of temperature. The addition of 5 mol% Er2O3 to single-crystal ZrO2 improved its creep resistance at high temperatures by 2 to 3 orders of magnitude over state-of-the-art Y2O3-doped crystals. Detailed microstructural characterization of ZrO2-Er2O3 single crystals has identified new mechanisms for improving the creep resistance of this class of materials. Adding Er2O3 to ZrO2 results in microstructure of stable and metastable tetragonal precipitates that with thermal treatment evolve to a tweed structure of nanosize tetragonal lamellae. The superior high-temperature creep resistance of Er2O3-doped ZrO2 is attributed to nanoscale precipitation hardening. Doping with Er2O3 will significantly increase the upper-use temperature limit of ZrO2. Potential applications include using Er2O3-doped ZrO2 as a high-temperature fiber for structural applications and adding Er2O3 to reduce the sintering rates of ZrO2 thermal barrier coatings. This work was conducted at Dpto. de F sica de la Materia Condensada, Universidad de Sevilla, Spain, and at NASA Glenn.

Martinez-Fernandez, Julian↗
NASA NTRS1957

A Fuselage Addition to Delay Drag-Rise Mach Number of Subsonic Airplanes at Lifting Conditions

The addition of fuselage volume, concentrated on top of the forward portion of the fuselage, for the purpose of delaying the drag-rise Mach number of subsonic airplanes at lifting conditions is investigated. The additions have been designed on the basis of the area rule and other important considerations to provide greater practicability of application compared with shapings previously investigated. The addition delayed the drag-rise Mach number by an increment of approximately 0.03 for a configuration having a wing with moderate thickness and 35 deg of sweepback at a lift coefficient of 0.3. A lesser delay was obtained for a configuration with a thicker wing. The additions increase the nonlinearities of the variations of pitching moment with lift,

Whitcomb, Richard T.↗
NASA NTRS2003

Common Ion Effects In Zeoponic Substrates: Dissolution And Cation Exchange Variations Due to Additions of Calcite, Dolomite and Wollastonite

c1inoptilolite-rich tuff-hydroxyapatite mixture (zeoponic substrate) has the potential to serve as a synthetic soil-additive for plant growth. Essential plant macro-nutrients such as calcium, phosphorous, magnesium, ammonium and potassium are released into solution via dissolution of the hydroxyapatite and cation exchange on zeolite charged sites. Plant growth experiments resulting in low yield for wheat have been attributed to a Ca deficiency caused by a high degree of cation exchange by the zeolite. Batch-equilibration experiments were performed in order to determine if the Ca deficiency can be remedied by the addition of a second Ca-bearing, soluble, mineral such as calcite, dolomite or wollastonite. Variations in the amount of calcite, dolomite or wollastonite resulted in systematic changes in the concentrations of Ca and P. The addition of calcite, dolomite or wollastonite to the zeoponic substrate resulted in an exponential decrease in the phosphorous concentration in solution. The exponential rate of decay was greatest for calcite (5.60 wt. % -I), intermediate for wollastonite (2.85 wt.% -I) and least for dolomite (1.58 wt.% -I). Additions of the three minerals resulted in linear increases in the calcium concentration in solution. The rate of increase was greatest for calcite (3.64), intermediate for wollastonite (2.41) and least for dolomite (0.61). The observed changes in P and Ca concentration are consistent with the solubilities of calcite, dolomite and wollastonite and with changes expected from a common ion effect with Ca. Keywords: zeolite, zeoponics, common-ion effect, clinoptilolite, hydroxyapatite

Beiersdorfer, R. E.↗