Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ARCS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Report on High Energy Arcing Fault Experiments: Experimental Results from Open Box Enclosures

This report documents an experimental program designed to investigate High Energy Arcing Fault (HEAF) phenomena. The experiments focus on providing data to better characterize the arc to improve the prediction of arc energy emitted during a HEAF event. An open box experiment allow for direct observation of the arc, which allows diagnostic instrumentation to record the phenomenological data needed for better characterization of the arc energy source term. The data collected supports characterization of the arc and arc jet, enclosure breach, material loss, and electrical properties. These results will be used to better characterizing the hazard for improvements in fire probabilistic risk assessment (PRA) realism. The experiments were performed at KEMA Labs located in Chalfont, Pennsylvania. The experimental design, setup, and execution were completed by staff from the NRC, the National Institute of Standards and Technology (NIST), Sandia National Laboratories (SNL) and KEMA Labs. In addition, representatives from the Electric Power Research Institute (EPRI) observed some of the experimental setup and execution. The HEAF experiments were performed between August 22, 2020 and September 18, 2020 on near-identical 51 cm (20 in) cube metal boxes suspended from a Unistrut support structure. The three-phase arcing fault was initiated at the ends of the conductors oriented vertically and located at the center of the box. Either aluminum or copper conductors were used for the conductors. The low-voltage experiments used 1 000 volts AC, while the medium-voltage experiments used 6 900 volts AC consistent with other recently completed experiments. Durations of the experiment ranged from 1 s to 5 s with fault currents ranging from 1 kA to 30 kA. Real-time electrical operating conditions, including voltage, current and frequency, were measured during the experiments. Heat fluxes and incident energies were measured with plate thermometers, radiometers, and slug calorimeters at various locations around the electrical enclosures. The experiments were documented with normal and high-speed videography, infrared imaging and photography.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2026

Power and particle exhaust for the ARC fusion power plant

To successfully show that fusion is an attractive energy source, the ARCTM fusion power plant will need to operate with a robust, integrated power and particle exhaust solution. To maximise ARC’s fusion power output while avoiding excessive erosion of the plasma-facing components, we will need to radiatively dissipate most of the power crossing the last-closed flux surface, injecting radiating impurities such as argon or neon to access divertor detachment. Divertor detachment will need to be integrated with a high-performance core plasma, and with efficient impurity pumping to prevent the accumulation of helium ash in the core. To access and control detachment in high-performance plasmas, we have designed ARC with up–down-symmetric divertors, with secondary X-points in long, tightly baffled outer legs. Using a core-edge modelling workflow, we predict that with this divertor design, ARC will access detachment with modest argon seeding in the divertor (c Ar,div ∼0.9%), which should have minimal impact on the core ( Z eff,core <0.5) for reasonable argon enrichment (c Ar,div /c Ar,core =6). Due to the high predicted divertor neutral pressure (p div ∼20 Pa), we predict that ARC will sufficiently pump helium to limit ash accumulation in the core (c He,core <2%) for a helium enrichment of c He,div /c He,core =0.4. ARC’s divertor design is expected to increase the stability of a detachment front in the outer divertor leg, helping to prevent divertor reattachment during smaller heat-flux transients such as scrape-off-layer filaments associated with the quasi-continuous exhaust regime. However, this buffering will not be sufficient to prevent divertor reattachment during large type-I edge-localised modes (ELMs), and as such these will need to be avoided on ARC. Experiments on SPARC will be used to select an integrated scenario which avoids or mitigates type-I-ELMs while maintaining access to detachment, good core fusion performance and sufficient impurity exhaust. SPARC experiments will also be used to finalise ARC’s divertor design, by studying the impact of magnetic and first-wall geometry on detachment stability, impurity enrichment and neutral baffling under conditions similar to those expected for ARC. In conclusion, our analysis finds that ARC will have a viable power and particle exhaust solution which is compatible with high-power operations, and this solution will be validated in experiments on SPARC.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Fast Reactor Physics Model Verification Studies using ARC and PyARC Workflows

PyARC was recently developed at Argonne National Laboratory to automate many of the tasks required in the ARC (Argonne Reactor Computation) fast reactor simulation workflow, from input file generation, code execution, data transfer between ARC codes, and output postprocessing. PyARC will likely be the path forward to train new users of the ARC codes with the goal of wide adoption by the national laboratories, academia, and industry. In particular, for the ANL-JAEA collaboration under the Civil Nuclear Working Group (CNWG) project agreement NE-01, PyARC will be used to model the Joyo and EBR-II reactors for comparisons with measured data and calculated results from JAEA (Task 3: Fast Reactor Fuel and Core). As an additional avenue for verification and validation, this report investigates the use of PyARC towards a variety of existing ARC-based reactor models, in order to understand its efficacy in replicating the behavior of base ARC codes and better understand any limitations within modeling realistic fast reactor problems. To this end, PyARC was used to model the Joyo MKI, RBEC Benchmark-M, PRISM Mod-B, and EBR-II Run 138B cores, and its results were compared to those from existing ARC-based models. It was found that for hexagonal-based geometries PyARC was able to replicate the behavior of ARC codes to within 10 pcm for small reactor cores, and ~150pcm difference in eigenvalue for larger cores. These discrepancies are attributed primarily to differences in local mesh refinement options between ARC and PyARC, which currently cannot be resolved with PyARC’s latest version (1.6.0). In some of these cases, PyARC was used to model steady-state problems with initial core compositions originating from a prior REBUS depletion calculation. While PyARC was not designed to support such steady-state calculations, workarounds were applied to replicate the behavior of ARC-based calculations as closely as possible. Thus, these results demonstrate the wide extent to which they can be applied to fast reactor problems while still providing immense benefit to the user in terms of automating and standardizing common routines within the fast reactor analysis workflow. This study concluded that PyARC will be suitable for modeling the steady-state conditions of the EBR-II and Joyo fast reactors as part of the CNWG project agreement.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1971

Calculated and observed features of stable auroral red arcs during three geomagnetic storms.

Satellite electron temperature and density data are used to calculate the structure of several stable auroral red arcs (SAR arcs) according to the thermal conduction model of the arc. The calculated lambda 6300 emission rates are compared with ground-based photometric observations taken at the same time and in the vicinity of the satellite crossings of the arcs. The SAR arcs analyzed include a range of lambda 6300 intensities, geographical locations, and times during the associated geomagnetic storm. In addition, satellite data were obtained at different altitudes over and within the SAR-arc region. Enhanced electron temperatures within or on the equatorward edge of an electron-density depression are common features of all the SAR arcs examined. There is general agreement between the calculated and observed lambda 6300 emission features for SAR arcs observed during the geomagnetic storm periods of Oct. 29 to Nov. 2, 1968, May 14-15, 1969, and Mar. 8-9, 1970. For these SAR arcs, thermal conduction from the magnetosphere alone is sufficient to excite the lambda 6300 emission to its observed intensity.

Roble, R. G.↗
NASA NTRS1990

Solar array arcing in plasmas

Solar cells in space plasma conditions are known to arc into the plasma when the interconnects are at a negative potential of a few hundred volts, relative to plasma potential. For cells with silver-coated interconnects, a threshold voltage for arcing exists at about -230 V, as found in both ground and LEO experiments. The arc rate beyond the threshold voltage depends nearly linearly on plasma density, but has a strong power-law dependence on voltage, such that for small increments in operating voltage there is a large increment in arc rate. The arcs generate broadband radio interference and visible light. In ground tests, interconnects have been damaged by arcs in cells having insufficient isolation from a source of high current. Models for the arcs are highly dependent on the choice of interconnect conductor material exposed to the plasma and possibly on the geometry and choice of adjacent insulator material. Finally, new technology solar cells use copper for the cell interconnects, a material which may have a lower arcing threshold voltage than silver. It is expected, from ground tests of simulated solar cells, that any junction of conductor and insulator exposed to space plasma conditions will arc into the plasma at a few hundred volts negative potential, relative to the local plasma.

Ferguson, Dale C.↗
NASA NTRS1990

Welding arc plasma physics

The problems of weld quality control and weld process dependability continue to be relevant issues in modern metal welding technology. These become especially important for NASA missions which may require the assembly or repair of larger orbiting platforms using automatic welding techniques. To extend present welding technologies for such applications, NASA/MSFC's Materials and Processes Lab is developing physical models of the arc welding process with the goal of providing both a basis for improved design of weld control systems, and a better understanding of how arc welding variables influence final weld properties. The physics of the plasma arc discharge is reasonably well established in terms of transport processes occurring in the arc column itself, although recourse to sophisticated numerical treatments is normally required to obtain quantitative results. Unfortunately the rigor of these numerical computations often obscures the physics of the underlying model due to its inherent complexity. In contrast, this work has focused on a relatively simple physical model of the arc discharge to describe the gross features observed in welding arcs. Emphasis was placed of deriving analytic expressions for the voltage along the arc axis as a function of known or measurable arc parameters. The model retains the essential physics for a straight polarity, diffusion dominated free burning arc in argon, with major simplifications of collisionless sheaths and simple energy balances at the electrodes.

Cain, Bruce L.↗
NASA NTRS1996

Emission Spectral Measurements in the Plenum of an Arc Jet Wind Tunnel

Arc jet wind tunnel facilities are used to evaluate thermal protection system materials for re-entry vehicles. The high speed, high temperature flowfield generated by the arc jet can simulate the extreme aerodynamic heating environment experienced during re-entry so that the survivability of heat shield materials and performance of various designs options can be tested. Although the re-entry heating environment can be approximated in the arc jet facility, the flowfield only partially simulates the actual re-entry flight conditions. Reynolds numbers are not matched so that surface shear stress distributions and mass transfer rates due to ablation or other mechanisms are not modeled correctly. Unlike flight conditions the arc freestream air is in non-equilibrium because of the rapid expansion that occurs in the supersonic nozzle. To properly study the actual re-entry flow environment, computational fluid dynamics, computational chemistry and radiation models must be used. Arc jet tunnel tests serve to validate these models. To perform accurate simulations inlet and boundary-conditions are needed, which come from measurements of the flowfield. The present study is concerned with measurements in the plenum region of an arc heater. In the past, conditions in the arc heater flowfield have been predicted using simulations since conventional measurement techniques could not be used in the harsh extremely high temperature environment. The present study is part of a recent push to utilize optical techniques to help better characterize the arc jet flowfields. Emission measurements have been made in the shock layer and the constrictor section of the arc heater to determine temperatures and species number densities. LIF measurements have been made in the free stream to determine temperature and velocity.

Donohue, Jim↗
NASA NTRS2001

Arc Inception Mechanism on a Solar Array Immersed in a Low-Density Plasma

In this report, results are presented of an experimental and theoretical study of arc phenomena and snapover for two samples of solar arrays immersed in argon plasma. The effects of arcing and snapover are investigated. I-V curves are measured, and arc and snapover inception voltages and arc rates are determined within the wide range of plasma parameters. A considerable increase in arc rate due to absorption of molecules from atmospheric air has been confirmed. It is shown that increasing gas pressure causes increasing ion current collection and, consequently, arc rate even though the effect of conditioning also takes place. Arc sites have been determined by employing a video-camera. It is confirmed that keeping sample under high vacuum for a long time results in shifting arc threshold voltage well below -300 V. The results obtained seem to be important for the understanding of arc inception mechanism.

Vayner, B.↗
NASA NTRS2005

Arcing in LEO - Does the Whole Array Discharge?

The conventional wisdom about solar array arcing in LEO is that only the parts the solar array that are swept over by the arc-generated plasma front are discharged in the initial arc. This limits the amount of energy that can be discharged. Recent work done at the NASA Glenn Research Center has shown that this idea is mistaken. In fact, the capacitance of the entire solar array may be discharged, which for large arrays leads to very large and possibly debilitating arcs, even if no sustained arc occurs. We present the laboratory work that conclusively demonstrates this fact by using a grounded plate that prevents the arc-plasma front from reaching certain array strings. Finally, we discuss the dependence of arc strength and arc pulse width on the capacitance that is discharged, and provide a physical mechanism for discharge of the entire array, even when parts of the array are not accessible to the arc-plasma front. Mitigation techniques are also presented.

Ferguson, Dale C.↗
NASA NTRS2005

Arcing in LEO: Does the Whole Array Discharge?

The conventional wisdom about solar array arcing in LEO is that only the parts of the solar array that are swept over by the arc-generated plasma front are discharged in the initial arc. This limits the amount of energy that can be discharged. Recent work done at the NASA Glenn Research Center has shown that this idea is mistaken. In fact, the capacitance of the entire solar array may be discharged, which for large arrays leads to very large and possibly debilitating arcs, even if no sustained arc occurs. We present the laboratory work that conclusively demonstrates this fact by using a grounded plate that prevents the arc-plasma front from reaching certain array strings. Finally, we discuss the dependence of arc strength and arc pulse width on the capacitance that is discharged, and provide a physical mechanism for discharge of the entire array, even when parts of the array are not accessible to the arc-plasma front. Mitigation techniques are also presented.

Ferguson, Dale C.↗
NASA NTRS2003

New Voltage and Current Thresholds Determined for Sustained Space Plasma Arcing

It has been known for many years, based partly on NASA Glenn Research Center testing, that high-voltage solar arrays arc into the space plasma environment. Solar arrays are composed of solar cells in series with each other (a string), and the strings may be connected in parallel to produce the entire solar array power. Arcs on solar arrays can damage or destroy solar cells, and in the extreme case of sustained arcing, entire solar array strings, in a flash. In the case of sustained arcing (discovered at Glenn and applied to the design and construction of solar arrays on Space Systems/Loral (SS/Loral, Palo Alto, CA) satellites, Deep-Space 1, and Terra), an arc on one solar array string can couple to an adjacent string and continue to be powered by the solar array output until a permanent electrical short is produced. In other words, sustained arcs produced by arcs into the plasma (so-called trigger arcs) may turn into disastrous sustained arcs by involving other array strings.

Dale C. Ferguson↗
DOE OSTI2025

ARC-100 Reactor Security-by-Design Summary 2025

This report applies the security-by-design methodology developed in a previous National Nuclear Security Administration–sponsored work to the ARC-100, a sodium-cooled fast reactor (SFR) being developed by ARC Clean Technology, Inc (ARC). The report contains no proprietary information specific to the ARC 100 reactor. The insights developed in this report are high-level, and generally applicable to other sodium fast reactor designs. The information presented here is the result of a qualitative safety-based analysis and would not inform any potential adversary beyond what would be found in a docketed safety analysis report. The scope of this present report covers ARC-100’s reactor core, used fuel storage, used fuel assembly wash station, cesium trap, sodium cold trap, noble gas decay tanks, used fuel dry storage facility, damaged fuel storage facility, and radioactive waste building. These systems are also compared to a generic SFR design assumed in the previous study. The security assessment results show changes in structures, systems, and components (SSCs) safety importance relative to the generic SFR SSCs. Several SSCs have higher importance rankings than others, and it is recommended that protection efforts are prioritized for these SSCs. Results from this work will furnish a technical justification for the feasibility of these solutions for the ARC reactor's design and, where applicable, identify any regulatory benefits conferred by the proactive design aspect within a risk management framework. This initiative will contribute to a more secure design of the ARC reactor and support its licensing process.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2020

Energy considerations regarding pulsed arc production of nanomaterials

Atmospheric arc discharge volumes have been estimated from the light distribution emitted during evaporation of graphite and molybdenum disulphide (MoS 2 ) anodes. These data have been correlated to the peak power in the case of pulsed arc discharge held at different frequencies (1, 2 and 5 Hz). The measured power density values and the corresponding specific energies per particle have been compared to DC values, and showed that pulsed arc discharges deliver electrical power more efficiently than DC arc discharges do with yet lower thermal loads. In particular, the power density of ≈1 kW/cm 3 characteristic of pulsed arcs (10-20 kW/cm 3 in DC) suffices to provide 15 eV/particle to the arc plasma (≈10 eV/particle or less in DC). Such an energy balance resulted in high ionization rates of the ablated material and production yields of carbon nanotubes around 10 11 cm -2 kWh -1 . Lastly, in situ probe experiments showed that pulsed arcs enhance the transport to substrate of the generated nanoparticles, such as graphene and MoS 2 monolayers. Pulsed anodic arcs open the possibility to generate further nanomaterials thanks to a more rational power investment and a better control of the discharge region.

42 ENGINEERING↗
NASA NTRS1962

Magnetically Diffused Radial Electric-Arc Air Heater Employing Water-Cooled Copper Electrodes

A magnetically rotated electric-arc air heater has been developed that is novel in that an intense magnetic field of the order of 10,000 to 25,000 gauss is employed. This field is supplied by a coil that is connected in series with the arc. Experimentation with this heater has shown that the presence of an intense magnetic field transverse to the arc results in diffusion of the arc and that the arc has a positive effective resistance. With the field coil in series with the arc, highly stable arc operation is obtained from a battery power supply. External ballast is not required to stabilize the arc when it is operating at maximum power level. The electrode erosion rate is so low that the airstream contamination is no more than 0.07 percent and may be substantially less.

COPPER↗
NASA NTRSDate not supplied

Quantifying Primary Arc-Induced Degradation of Perovskite Solar Cells

Primary arcing induced by spacecraft charging presents a significant hazard to thin film solar cells if left unchecked. Here, we present the results of a preliminary effort to quantify the impacts of primary arcing to perovskite solar cells. Solar cells operating in a charged environment are susceptible to electrostatic discharges known as arcing. While primary arcs are not generally considered a major concern for traditional space PV, for thin film cells, these can induce significant heating and subsequent damage. We conducted ESD testing in a LEO-like plasma in the National Plasma Interaction Facility at NASA Glenn Research Center to quantify impacts to cell performance by arcing. The perovskites tested saw a decrease of short circuit current with an increased number of arcs, averaging a relative change of 73.89 ± 15.90% after 60 total arcs supplied a cumulative energy dose of 76.12 mJ to the string. Ongoing work entails testing with larger perovskite data sets and expanding to include additional thin film cell technologies to demonstrate the risk unmitigated primary arcing presents.

primary arcing↗
DOE OSTI2022

Quarterly Management Document – FY22, 1st Quarter, Multi-pass Hybrid Laser Arc Welding of Alloy 740H

This report summarizes the progress made on the project during the first quarter of FY22. The model for deep penetration laser welding continues to be developed to understand and mitigate cracking issues associated with laser welding Alloy 740H. The effects of laser wobble on laser welding of this alloy are also being developed. Additionally, the short-term creep behavior of welds made by various hybrid laser arc parameters has been obtained and the results indicate they are comparable to welds made by conventional gas tungsten arc welding which is a factor 2 slower than the hybrid welds. Additionally, the creep behavior of laser-only welds is also consistent with conventional gas tungsten arc welds as well as the hybrid laser arc welds made under this project. However, the creep rate of the laser-only welds is much higher than that observed in the hybrid laser arc welded specimens. This is most likely due to the narrower weld produced by laser-only welding compared to hybrid laser arc welding and, thus, the higher creep rate of laser-only welded creep specimens is likely a result of the increased fraction of base metal (which exhibits a higher creep rate than weld metal) contained within the gage section of the creep specimen. Creep rupture lifetimes were all about the same for both laser-only and hybrid laser arc welded specimens and consistent with the creep rupture lifetime of conventional gas tungsten arc welded creep specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Unipolar arc plasmas on nanostructured tungsten surfaces under perpendicular magnetic field

Abstract Unipolar arcing is an important phenomenon in terms of wall erosion and the subsequent plasma contamination in nuclear fusion devices. In this study, unipolar arc plasmas are experimentally explored under the presence of the external magnetic field perpendicular to a tungsten (W) sample on which a ‘fuzz’ nanostructure surface is formed. It is found that the fuzz layer thickness, d fuzz , plays a dominant role in determining the motion of arc spots, the arc ignition probability, and arc plasma parameters. High-speed imaging reveals that the motion of arc spots becomes more collective, as d fuzz increases. Interestingly, arc spots make a circle while moving outward. With increasing d fuzz , the amount of eroded W atoms increases, as indicated from an observed increase in the total visible emission intensity, while the arc ignition probability is found to drop. The physical mechanisms are discussed, in detail, based on spectroscopic measurements of the electron temperature, obtained from Boltzmann plots of both W I and W II, and the electron density, determined from Stark broadening of W I lines.

Physics↗
NASA NTRS1985

Model of oval and polar cap arc configurations

A model of oval and polar cap arc configurations has been formulated by combining the theory of antiparallel magnetic merging and theories of the evening discrete arc and of the morningside arc systems. Aside from incorporating the verified and yet-to-be-verified predictions of the individual component theories this unified model leads to definite predictions of not only arc configurations but also characteristics of the plasmas that produce the various types of arcs. The model predicts two types of polar cap arcs characterized by the plasma sources: the magnetosheath arc and the plasma sheet arc. Their occurrence should be governed by the By component of the interplanetary magnetic field, and the same type should not occur simultaneously in both hemispheres.

Chiu, Y. T.↗