Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ACOUSTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Downhole nonlinear acoustics measurements in rock formations using dynamic acoustic elasticity and time reversal

Apparatus and methods for measurement of pore pressure in rock formations through an open, or cemented and/or cased, borehole are described. Such measurements are achieved using the Dynamic Acoustic Elasticity (DAE) method for characterizing nonlinear parameters by perturbing a selected rock formation volume with a High Amplitude, Low Frequency (HALF) acoustic strain wave, and probing this volume using a Low Amplitude, High Frequency (LAHF) acoustic wave. Time reversal techniques may be employed for focusing acoustic energy Into the formation in the vicinity of the pipe or open hole.

Goodman, Harvey Edwin↗

Acoustic Modeling of Novel Over-The-Rotor Acoustic Liner Concepts Using COMSOL Multiphysics Simulation Software

This paper presents simulation predictions of novel over-the-rotor acoustic liner configurations compared with experimental data. This is a follow on to the investigation on the effect of grazing flow on grooved over-the-rotor casing treatments. The purpose of this modeling investigation stems from the determination that traditional liner modeling techniques are inadequate for nontraditional internal liner cavity geometries. A series of these expansion chamber type liner design concepts were previously developed by Glenn Research Center and tested using the Langley Research Center Normal Incidence Tube. The measured normalized impedance and absorption coefficient is compared with that obtained from the COMSOL Multiphysics® simulation. Additionally, using a parametric case study, another series of simulations were conducted to determine what additional benefits, if any, this genre of liner has to offer the acoustics community. A total of 53 permutations of this concept was investigated. The results indicate that with longer internal fins, the resonance is sifted to lower frequencies.

Acoustics↗

Design guidelines for avoiding thermo-acoustic oscillations in helium piping systems

Thermo-acoustic oscillations are a commonly observed phenomenon in helium cryogenic systems, especially in tubes connecting hot and cold areas. The open ends of these tubes are connected to the lower temperature (typically at 4.2 K), and the closed ends of these tubes are connected to the high temperature (300K). Cryogenic instrumentation installations provide ideal conditions for these oscillations to occur due to the steep temperature gradient along the tubing. These oscillations create errors in measurements as well as an undesirable heat load to the system. The work presented here develops engineering guidelines to design oscillation-free helium piping. This work also studies the effect of different piping inserts and shows how the proper geometrical combinations have to be chosen to avoid thermo-oscillations. The effect of an 80 K intercept is also studied and shows that thermo-oscillations can be dampened by placing the intercept at an appropriate location.

43 PARTICLE ACCELERATORS↗

Gigahertz acoustic vibrations of elastically anisotropic Indium–tin-oxide nanorod arrays [Gigahertz modulation of the full visible spectrum via acoustic vibrations of elastically anisotropic Indium-tin-oxide nanorod arrays]

Active control of light is important for photonic integrated circuits, optical switches,. and telecommunications. Coupling light with acoustic vibrations in nanoscale optical resonators offers optical modulation capabilities with high bandwidth and Small footprint Instead of using noble metals, here we introduce indium tin-oxide nanorod arrays (ITO-NRAs) as the operating media;and demonstrate optical modulation covering the visible spectral range (from 360 to 700 nm), with similar to 20 GHz bandwidth through the excitation of coherent acoustic vibrations in ITO-NRAs. This broadband modulation results from the collective optical diffraction by the dielectric ITO-NRAs, and a high differential transmission modulation up to 10% is achieved through efficient near-infrared, on-plasmon-resonance pumping. By combining the frequency signatures Of the vibrational modes with finite-element simulations, we,further determine the anisotropic elastic constants for single-crystalline ITO, which are not known-for the bulk phase. Furthermore, this technique to determine elastic constants using Coherent acoustic vibrations of uniform nanostructures can be generalized to the study of other inorganic materials.

36 MATERIALS SCIENCE↗

An Evaluation of the Additional Acoustic Power Needed to Overcome the Effects of a Test-Articles Absorption During Reverberant Chamber Acoustic Testing of Spaceflight Hardware

It is important to realize that some test-articles may have significant sound absorption that may challenge the acoustic power capabilities of a test facility. Therefore, to mitigate this risk of not being able to meet the customers target spectrum, it is prudent to demonstrate early-on an increased acoustic power capability which compensates for this test-article absorption. This paper describes a concise method to reduce this risk when testing aerospace test-articles which have significant absorption. This method was successfully applied during the SpaceX Falcon 9 Payload Fairing acoustic test program at the NASA Glenn Research Center Plum Brook Stations RATF.

sound power↗

Validation of finite element analysis strategy to investigate acoustic levitation in a two-axis acoustic levitator

A two-axis acoustic levitator can be used to generate a standing pressure wave capable of levitating solid and liquid particles at appropriate input conditions. This work proposes a simulation framework to investigate the two-axis levitation particle stability using a commercial, computational fluid dynamics software based on the harmonic solution to the acoustic wave equation. The simulation produced predictions of the standing wave that include a strong "+" shaped pattern of nodes and anti-nodes that are aligned with the levitator axes. To verify the simulation, a levitator was built and used to generate the standing wave. The field was probed with a microphone and a motorized-scanning system. After scaling the simulated pressure to the measured pressure, the magnitudes of the sound pressure level at corresponding high-pressure locations were different by no more than 5%. This is the first time a measurement of a two-axis levitator standing pressure wave has been presented and shown to verify simulations. Furthermore, as an additional verification, the authors consulted high speed camera measurements of a reference-levitator transducer, which was found to have a maximum peak-to-peak displacement of 50 +/- 5 mu m. The reference-levitator is known to levitate water at 160 dB. The system for this work was simulated to match the operation of the reference-levitator so that it produced sound pressure levels of 160 dB. This pressure was achieved when the transducer maximum peak-to-peak displacement was 50.8 mu m. The agreement between the two levitators' displacements provides good justification that the modeling approach presented here produces reliable results.

2 axis levitator↗

Electron–acoustic phonon coupling in single crystal CH 3 NH 3 PbI 3 perovskites revealed by coherent acoustic phonons

The intrinsic properties of CH 3 NH 3 PbI 3 are still largely unknown in spite of the great amount of attention it has received for its solar cell application. Mobility of charges is a quintessential property in this aspect; however, there is still no clear understanding of electron transport, as reported values span over three orders of magnitude. Here we develop a method to measure the electron and hole deformation potentials using coherent acoustic phonons generated by femtosecond laser pulses. Furthermore, we apply this method to characterize a CH 3 NH 3 PbI 3 single crystal.We measure the acoustic phonon properties and characterize electron-acoustic phonon scattering. Then, using the deformation potential theory, we calculate the carrier intrinsic mobility and compare it to the reported experimental and theoretical values. These results reveal high electron and hole mobilities of 2,800 and 9,400 cm 2 V -1 s -1 , respectively. Comparison with literature values of mobility demonstrates the potential role played by polarons in charge transport in CH 3 NH 3 PbI 3 .

14 SOLAR ENERGY↗

Spin–phonon interactions in silicon carbide addressed by Gaussian acoustics [Probing spin-phonon interactions in silicon carbide with Gaussian acoustics]

Hybrid spin-mechanical systems provide a platform for integrating quantum registers and transducers. Efficient creation and control of such systems require a comprehensive understanding of the individual spin and mechanical components as well as their mutual interactions. Point defects in silicon carbide (SiC) offer long-lived, optically addressable spin registers in a wafer-scale material with low acoustic losses, making them natural candidates for integration with high quality factor mechanical resonators. Here, we show Gaussian focusing of a surface acoustic wave in SiC, characterized by a novel stroboscopic X-ray diffraction imaging technique, which delivers direct, strain amplitude information at nanoscale spatial resolution. Using ab initio calculations, we provide a more complete picture of spin-strain coupling for various defects in SiC with C 3v symmetry. This reveals the importance of shear for future device engineering and enhanced spin-mechanical coupling. We demonstrate all-optical detection of acoustic paramagnetic resonance without microwave magnetic fields, relevant to sensing applications. Lastly, we show mechanically driven Autler-Townes splittings and magnetically forbidden Rabi oscillations. These results offer a basis for full strain control of three-level spin systems.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Real-time observation of coherent acoustic phonons generated by an acoustically mismatched optoacoustic transducer using x-ray diffraction

The spectrum of laser-generated acoustic phonons in indium antimonide coated with a thin nickel film has been studied using time-resolved x-ray diffraction. Strain pulses that can be considered to be built up from coherent phonons were generated in the nickel film by absorption of short laser pulses. Acoustic reflections at the Ni–InSb interface leads to interference that strongly modifies the resulting phonon spectrum. The study was performed with high momentum transfer resolution together with high time resolution. This was achieved by using a third-generation synchrotron radiation source that provided a high-brightness beam and an ultrafast x-ray streak camera to obtain a temporal resolution of 10 ps. We also carried out simulations, using commercial finite element software packages and on-line dynamic diffraction tools. Using these tools, it is possible to calculate the time-resolved x-ray reflectivity from these complicated strain shapes. The acoustic pulses have a peak strain amplitude close to 1%, and we investigated the possibility to use this device as an x-ray switch. At a bright source optimized for hard x-ray generation, the low reflectivity may be an acceptable trade-off to obtain a pulse duration that is more than an order of magnitude shorter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Acoustic spin pumping in magnetoelectric bulk acoustic wave resonator

We present the generation and detection of spin currents by using magnetoelastic resonance excitation in a magnetoelectric composite high overtone bulk acoustic wave (BAW) resonator (HBAR) formed by a Al-ZnO-Al-GGG-YIG-Pt structure. Transversal BAW drives magnetization oscillations in YIG film at a given resonant magnetic field, and the resonant magneto-elastic coupling establishes the spin-current generation at the Pt/YIG interface. Due to the inverse spin Hall effect (ISHE) this BAW-driven spin current is converted to a dc voltage in the Pt layer. The dependence of the measured voltage both on magnetic field and frequency has a resonant character. The voltage is determined by the acoustic power in HBAR and changes its sign upon magnetic field reversal. We compare the experimentally observed amplitudes of the ISHE electrical field achieved by our method and other approaches to spin current generation that use surface acoustic waves and microwave resonators for ferromagnetic resonance excitation, with the theoretically expected values.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Partially acoustic dark matter cosmology and cosmological constraints

The Observations of the cosmic microwave background (CMB) together with weak lensing measurements of the clustering of large scale cosmological structures and local measurements of the Hubble constant pose a challenge to the standard ΛCDM cosmological model. On one side CMB observations imply a Hubble constant that is lower than local measurements and an amplitude of the lensing signal that is higher than direct measurements from weak lensing surveys. We investigate a way of relieving these tensions by adding dark radiation tightly coupled to an acoustic part of the dark matter sector and compare it to massive neutrino solutions. While these models offer a way of separately relieving the Hubble and weak lensing tensions they are prevented from fully accommodating both at the same time since the CMB requires additional cold dark matter when adding acoustic dark matter or massive neutrinos to preserve the same sharpness of the acoustic peaks which counteracts the desired growth suppression.

79 ASTRONOMY AND ASTROPHYSICS↗

Hitting the target: fragment screening with acoustic in situ co-crystallization of proteins plus fragment libraries on pin-mounted data-collection micromeshes

A method is presented for screening fragment libraries using acoustic droplet ejection to co-crystallize proteins and chemicals directly on micromeshes with as little as 2.5 nl of each component. This method was used to identify previously unreported fragments that bind to lysozyme, thermolysin, and trypsin. Acoustic droplet ejection (ADE) is a powerful technology that supports crystallographic applications such as growing, improving and manipulating protein crystals. A fragment-screening strategy is described that uses ADE to co-crystallize proteins with fragment libraries directly on MiTeGen MicroMeshes. Co-crystallization trials can be prepared rapidly and economically. The high speed of specimen preparation and the low consumption of fragment and protein allow the use of individual rather than pooled fragments. The Echo 550 liquid-handling instrument (Labcyte Inc., Sunnyvale, California, USA) generates droplets with accurate trajectories, which allows multiple co-crystallization experiments to be discretely positioned on a single data-collection micromesh. This accuracy also allows all components to be transferred through small apertures. Consequently, the crystallization tray is in equilibrium with the reservoir before, during and after the transfer of protein, precipitant and fragment to the micromesh on which crystallization will occur. This strict control of the specimen environment means that the crystallography experiments remain identical as the working volumes are decreased from the few microlitres level to the few nanolitres level. Using this system, lysozyme, thermolysin, trypsin and stachydrine demethylase crystals were co-crystallized with a small 33-compound mini-library to search for fragment hits. This technology pushes towards a much faster, more automated and more flexible strategy for structure-based drug discovery using as little as 2.5 nl of each major component.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Acoustic testing of a supersonic tip speed fan with acoustic treatment and rotor casting slots. Quiet engine program scale model fan C

Acoustic tests were conducted on a high tip speed (1550 ft/sec, 472.44 m/sec) single stage fan with varying amounts of wall acoustic treatment and with circumferential slots over the rotor blade tips. The slots were also tested with acoustic treatment placed behind the slots. The wall treatment results show that the inlet treatment is more effective at high fan speeds and aft duct treatment is more effective at low fan speeds. Maximum PNL's on a 200-foot (60.96 m) sideline show the untreated slots to have increased the rear radiated noise at approach. However, when the treatment was added to the slots inlet radiated noise was decreased, resulting in little change relative to the solid casing on an EPNL basis.

Kazin, S. B.↗

On the relationship between acoustic energy density flux near the jet axis and far field acoustic intensity

By measurement and analysis, the relationship between the distribution of the outflow of acoustic energy over the jet boundary and the far-field intensity is considered. The physical quantity used is the gradient of the pressure evaluated on a geometrical plane at the smallest possible radial distance from the jet axis, but outside the vortical region, in the area where the homogeneous wave equation is reasonably well satisfied. The numerical and experimental procedures involved have been checked out by using a known source. Results indicate that the acoustic power output per unit length of the jet, in the region from which the sound emanates, peaks at approximately 9 diameters downstream. The acoustic emission for a jet Strouhal number of about 0.3 exceeds the emission for all other Strouhal numbers nearly everywhere along the measurement plane. However, the far-field peak intensity distribution obtained from the contribution of each station was found to depend on the spatial extent of the region where sound emanates from the jet, which, in turn, depends more on the far-field angle than on the Strouhal number.

Maestrello, L.↗

On the relationship between acoustic energy density flux near the jet and far field acoustic intensity

The relationship between the distribution of the outflow of acoustic energy over the jet boundary and the far-field directivity and intensity distribution is established by measurement and analysis. The numerical and experimental procedures involved have been checked out by using a known source. The results indicate that the acoustic power output per unit length of the jet, in the region from which the sound emanates, peaks at approximately 9 diameters downstream. The acoustic emission for a jet Strouhal number of about 0.3 exceeds the emission for all other Strouhal numbers nearly everywhere along the measurement plane. However, the far-field peak intensity distribution obtained from the contribution of each station was found to depend on the spatial extent of the region where sound emanates from the jet, which, in turn, depends more on the far-field angle than on the Strouhal number. The implications of these results for sound suppression techniques are discussed.

Maestrello, L.↗

A unique method to study acoustic transmission through ducts using signal synthesis and averaging of acoustic pulses

An acoustic impulse technique using a loudspeaker driver is developed to measure the acoustic properties of a duct/nozzle system. A signal synthesis method is used to generate a desired single pulse with a flat spectrum. The convolution of the desired signal and the inverse Fourier transform of the reciprocal of the driver's response are then fed to the driver. A signal averaging process eliminates the jet mixing noise from the mixture of jet noise and the internal noise, thereby allowing very low intensity signals to be measured accurately, even for high velocity jets. A theoretical analysis is carried out to predict the incident sound field; this is used to help determine the number and locations of the induct measurement points to account for the contributions due to higher order modes present in the incident tube method. The impulse technique is validated by comparing experimentally determined acoustic characteristics of a duct-nozzle system with similar results obtained by the impedance tube method. Absolute agreement in the comparisons was poor, but the overall shapes of the time histories and spectral distributions were much alike.

Salikuddin, M.↗