Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “6.1”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

An investigation of drag reduction for a standard truck with various modifications

A wind tunnel investigation was conducted to determine the influence of several physical variables on the aerodynamic drag of a standard truck model. The physical variables included: a cab mounted air deflector; a boattail on the rear of the cargo compartment; flow-vanes on the front of the cargo compartment; and a forebody fairing over the cab. Tests were conducted at yaw angles (relative wind angle) of 0, 5, 10, 20, and 30 degrees and Reynolds numbers of 3.4 x 100,000 to 6.1 x 100,000 based upon the equivalent diameter of the vehicles. The forebody fairing and the flow-vane with the closed bottom were very effective in improving the flow over the forward part of the cargo compartment. The forebody fairing provided a calculated fuel saving of 5.6 liters per hour (1.5 gallons per hour) over the baseline configuration for a ground speed of 88.6 km/hr (55 mph) in national average winds.

Muirhead, V. U.↗

Preliminary study of head-up assessment techniques. 1: Viewing duration of instrument panel and HUD symbology using a recall methodology

Eight commercial pilots were shown 50 colored, high fidelity slides of a standard instrument panel (IP) with the needle positions of each instrument varying from slide to slide and then 50 slides of a head-up display (HUD) symbology format which contained an equivalent amount of flight-related information as the instrument panel slides. All stimuli were presented under controlled, static viewing conditions that allowed the measurement of the speed and accuracy with which one randomly selected flight parameter on each slide could be read. The subject did not know which parameter would be requested and, therefore, had to remember the total set of information in order to answer the question correctly. The results showed that from 6.6 - 8.7 sec total viewing time was required to correctly extract altitude, airspeed, heading, VSI, or ADI from the IP slides and from 6.1 to 7.4 sec for the HUD slides.

Haines, R. F.↗

Observations of the Crab Nebula, NGC 4151, Cyg X1 and Cyg X3 at medium gamma ray energies

The paper analyzes observations of the Crab Nebula, NGC 4151, Cyg X1, and Cyg X3 taken with the UCR gamma ray telescope at a residual atmospheric depth of about 3.5 g/sq cm on a balloon launched from Palestine, Texas, 4.5 GV, 2000 local time LT (0100 UT), on September 29, 1978. The data consists of continuous observations from 0430 LT (0930 UT) on September 30 to 1800 LT (2300 UT) on October 1, 1979. A flux increase is observed at the right ascension of the Crab Nebula within about a 10 min uncertainty of telescope source position determination, eliminating the SAS-2, CG 195+4, and the two COS-B sources in the antigalactic center direction as the origin of the gamma rays. The total flux of gamma rays for the Crab Nebula from 1.2 to 10 MeV is (6.1 + or - 1.5) x 10 to the -3rd photons/sq cm-s, with an upper limit at 10-20 MeV of 7 x 10 to the -5th photons/sq cm-s. Results for the NGC 4151, Cyg X1, and Cyg X3 are also discussed and flux upper limits are given.

Zanrosso, E. M.↗

Observations of 1-30 MeV gamma rays from the galactic center

Preliminary results are reported for gamma ray observations of the galactic center region made during a 15-hour balloon flight from Alice Springs, Australia on April 18, 1979. The observations were carried out with the UGR double-scatter gamma-ray telescope at energies of 1 to 30 MeV. The observations are compatible with a galactic source of approximately equal brightness along the region of system II galactic longitudes between 300 and 60 deg. The energy distribution joins smoothly to previous spark chamber results at energies above 30 MeV and to scintillator results below 1 MeV. It appears to be a combination of nuclear gamma ray lines superimposed on a power-law bremsstrahlung spectrum. The metastable C-12 line at 4.4 MeV appears to be present with a significance of about 16 standard deviations. The flux in the line is 0.0006 + or - 0.0003 photons/sq cm per sec per rad. The oxygen line at 6.1 MeV does not seem to appear significantly above background.

Zanrosso, E.↗

Shuttle solid rocket motor nozzle alternate ablative evaluation

A series of subscale tests are shown to suggest that a lower-cost ablative material than the rayon-based carbon ablative currently used in the Space Shuttle Solid Rocket Motor (SRM) may be used as a substitute. Six such ablatives with outstanding performance characteristics, using spun PAN and continuous pitch and PAN fibers instead of the present, continuous rayon, were identified in the course of tests with HTPB/AL/AP solid propellant grains with a burn time of 12 sec. The test nozzle features an initial throat diameter of 2.2 in. and a 6.1 expansion ratio. In addition to nozzle structural feature drawings, extensive test data tables and propellant formulation and properties tables are provided.

Powers, L. B.↗

Simulation of a hydrocarbon fueled scramjet exhaust

Exhaust nozzle flow fields for a fully integrated, hydrocarbon burning scramjet were calculated for flight conditions of M (undisturbed free stream) = 4 at 6.1 km altitude and M (undisturbed free stream) = 6 at 30.5 km altitude. Equilibrium flow, frozen flow, and finite rate chemistry effects are considered. All flow fields were calculated by method of characteristics. Finite rate chemistry results were evaluated by a one dimensional code (Bittker) using streamtube area distributions extracted from the equilibrium flow field, and compared to very slow artificial rate cases for the same streamtube area distribution. Several candidate substitute gas mixtures, designed to simulate the gas dynamics of the real engine exhaust flow, were examined. Two mixtures are found to give excellent simulations of the specified exhaust flow fields when evaluated by the same method of characteristics computer code.

Leng, J.↗

Design predictions for noise control in the cryogenic National Transonic Facility

Noise control in the National Transonic Facility - a cryogenic wind tunnel - has been examined in terms of acoustical design criteria, drive-fan noise and exhaust system noise. A duct lining with two layers of perforated sheeting and a gas-filled honeycomb core was selected for attenuating drive-fan noise. With the exception of attenuation peaks, attenuation of the lining was found to experimentally agree with predicted values at 20 C air temperatures. Exhaust system noise will be attenuated with a large muffler used in conjunction with a 6.1-m high acoustical enclosure. Fan noise from the fan-ejector system will be attenuated by fan silencers and the acoustic enclosure.

Lassiter, W. S.↗

Accelerator test of the coded aperture mask technique for gamma-ray astronomy

A prototype gamma-ray telescope employing the coded aperture mask technique has been constructed and its response to a point source of 20 MeV gamma-rays has been measured. The point spread function is approximately a Gaussian with a standard deviation of 12 arc minutes. This resolution is consistent with the cell size of the mask used and the spatial resolution of the detector. In the context of the present experiment, the error radius of the source position (90 percent confidence level) is 6.1 arc minutes.

Jenkins, T. L.↗

First results from a superconductive detector for moving magnetic monopoles

A velocity- and mass-independent search for moving magnetic monopoles is being performed by continuously monitoring the current in a 20-sq cm area superconducting loop. A single candidate event, consistent with one Dirac unit of magnetic charge, has been detected during five runs totaling 151 days. These data set an upper limit of 6.1 x

Cabrera, B.↗

An absorption feature in the spectrum of a gamma ray burst on 25 March 1978

The High Energy X-ray and Low Energy Gamma Ray Experiment on HEAO-1 detected a gamma ray burst on March 25, 1978. The main peak of the event lasted 10 seconds, while less intense emission was observed for approximately 100 seconds. The burst spectrum shows an apparent absorption feature at 55 +/- 5 keV with an equivalent width of 13 +/- 3 keV, values commensurate with those reported for bursts recorded by the KONUS experiment. The integrated fluence between 30 keV and 6.1 Mev was 0.000015 ergs/sq cm. The detection syste has localized the burst source to within a degree of RA = 237.2 deg and Dec. = 76.4 deg.

Hueter, G. J.↗

Calibration of the active radiation detector for Spacelab-One

The flight models of the active radiation detector (ARD) for the ENV-01 environmental monitor were calibrated using gamma radiation. Measured sensitivities of the ion chambers were 6.1 + or - 0.3 micron rad per count for ARD S/N1, and 10.4 + or - 0.5 micron rad per count for ARD S/N2. Both were linear over the measured range 0.10 to 500 m/rad hour. The particle counters (proportional counters) were set to respond to approximately 85% of minimum ionizing particles of unit charge passing through them. These counters were also calibrated in the gamma field.

Source record↗

Large diameter astromast development, phase 1

Coilable-longeron lattice columns called Astromasts (trademark) were manufactured for a variety of spacecraft missions. These flight structures varied in diameter from 0.2 to 0.5 meter (9 to 19 in.), and the longest Astromast of this type deploys to a length of 30 meters (100 feet). A double-laced diagonal Astromast design referred to as the Supermast (trademark) which, because it has shorter baylengths than an Astromast, is approximately four times as strong. The longeron cross section and composite material selection for these structures are limited by the maximum strain associated with stowage and deployment. As a result, future requirements for deployable columns with high stiffness and strength require the development of both structures in larger diameters. The design, development, and manufacture of a 6.1-m-long (20-ft), 0.75-m-diameter (30-in.), double-laced diagonal version of the Astromast is described.

Preiswerk, P. R.↗

Solar radio burst and in situ determination of interplanetary electron density

A few interplanetary electron density scales which were derived from the analysis of interplanetary solar radio burst are discussed and compared to a model derived from 1974 to 1980 Helios 1 and 2 in situ density observations made in the 0.3 to 1.0 AU range. The Helios densities were normalized to 1976 with the aid of IMP and ISEE data at 1 AU, and were then sorted into 0.1 AU bins and logarithmically averaged within each bin. The best fit to these 1976-normalized, bin averages is N(R(AU)) = 6.1 R(-2.10)/cu cm. This model is in rather good agreement with the solar burst determination if the radiation is assumed to be on the second harmonic of the plasma frequency. This analysis also suggests that the radio emissions tend to be produced in regions denser than the average where the density gradient decreases faster with distance than the observed R(-2.10).

Bougeret, J. L.↗

New radar-derived topography for the northern hemisphere of Mars

Earth-based radar altimetry data for the northern equatorial belt of Mars (6 deg S-23 deg N) have recently been reduced to a common basis corresponding to the 6.1-mbar reference surface. A first look at these data indicates that the elevations of Tharsis, Elysium, and Lunae Planum are lower (by 2-5 km) than has been suggested by previous estimates. These differences show that the required amount of tectonic uplift (or constructional volcanism) for each area is less than has been previously envisioned. Atmospheric or surficial conditions are suggested which may explain the discrepancies between the radar topography and elevations measured by other techniques. The topographies of Chryse Planitia, Syrtis Major, and Valles Marineris are also described.

Downs, G. S.↗

Kinetics of the reaction O + HO2 yields OH + O2 from 229 to 372 K

The discharge-flow resonance fluorescence technique has been used to obtain absolute rate data for the O + HO2 reaction from 229 to 372 K at a total pressure of 1 torr. Pseudo-first-order conditions were used with HO2 concentrations in large excess over initial atomic oxygen in order to minimize interference from secondary reactions. The results are independent of the method used to generate HO2 and atomic oxygen. At 299 K, the result is (6.1 + or - 0.4) x 10 to the -11th cu cm/molecule s. The temperature dependence expressed in Arrhenius form is (3.1 + or - 0.3) x 10 to the -11th exp/(+200 + or - 28)/T/. The error limits given are twice the standard deviation; overall experimental error is estimated to be + or - 25%.

Keyser, L. F.↗

Hypsometric studies of Mars.

Altitude data derived from the 12.6 cm radar measurements obtained at JPL's Goldstone Facility were used to explore the utility of this type of regional analysis and to develop criteria for the interpretation of hypsometric data for planets where no visual images are available. Examination of the radar-derived hypsogram for Mars shows that the unimodal distribution of elevations contains several second order peaks and is skewed toward a modal elevation of about 3.5 km above the 6.1 mb datum. Individual topographic features can be recognized from this hypsogram, but such interpretations are based on the known surface morphology that has been determined from spacecraft images. It is not yet known how, for example, cratered terrain, regional slopes or other morphological features could be identified using the hypsogram if no images were available for ground-truth. The role that large impact craters play in influencing the shape of a hypsogram is being studied.

Blake, P. L.↗

Solar radio burst and in situ determination of interplanetary electron density

A few interplanetary electron density scales which were derived from the analysis of interplanetary solar radio burst are discussed and compared to a model derived from 1974 to 1980 Helios 1 and 2 in situ density observations made in the 0.3 to 1.0 AU range. The Helios densities were normalized to 1976 with the aid of IMP and ISEE data at 1 AU, and were then sorted into 0.1 AU bins and logarithmically averaged within each bin. The best fit to these 1976-normalized, bin averages is in N(R(AU)) = 6.1 R(-2.10)/cu cm. This model is in rather good agreement with the solar burst determination if the radiation is assumed to be on the second harmonic of the plasma frequency. This analysis also suggests that the radio emissions tend to be produced in regions denser than the average where the density gradient decreases faster with distance than the observed R(-2.10). Previously announced in STAR as N83-35989

King, J. H.↗

The 1000 GeV gamma rays from ms pulsars

The detection of 1000 GeV gamma-rays with the characteristic 6.1 ms periodicity of the radio pulsar PSR 1953 +29 is reported. This result, significant at the 5.4 beta level, provides the first direct evidence for the association of the 6 ms radio pulsar PSR1953+29 with the gamma-ray source 2CG065+0. Extensive observations of the 1.5 ms pulsar PSR 1937 are also reported.

Chadwick, P. M.↗