SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Interface sputter damage effects were measured for Sn-doped (approximately 2x10 to the 17th power/cu cm) 100 oriented GaAs. The sputter surfaces were characterized by Auger and X-ray photoelectron spectroscopy. Gold contacts were then deposited in situ on these characterized surfaces. Results of I-V and C-V measurements are shown in graphs.
This manuscript describes the chemical transformations that occur during hydrolysis of uranium tetrafluoride (UF 4 ) due to its storage in humid air (85% and 50% relative humidity) at ambient temperatures. This hydrolysis was previously reported to proceed slowly or not at all (depending on the percent relative humidity); however, previous reports relied primarily on X-ray diffraction methods to probe uranium speciation. Here, we employ a battery of physiochemical probing techniques to explore potential hydrolysis, including Raman spectroscopy, powder X-ray diffraction, 19 F nuclear magnetic resonance spectroscopy, scanning electron microscopy, and focused ion beam microscopy with energy-dispersive X-ray spectroscopy. Of these, only Raman spectroscopy proved to be particularly useful at observing chemical changes to UF 4 . It was found that anhydrous UF 4 slightly oxidizes over the course of thirteen days to Schoepite-like uranium complexes and possibly UO 3 . In contrast, UF 4 exposed to 50% relative humidity slightly decomposes into UO 2 F 2 , Schoepite-like uranium complexes, and possibly a high order uranium oxide that eluded chemical assignment (U x O y ). Despite the rich chemical speciation observed in our Raman spectroscopy measurements, X-ray diffraction and 19 F NMR measurements on the same material showed no changes. Microscopy measurements suggest that the observed reactions between UF 4 and water occur primarily on the surface of UF 4 particulates via a method that is visually similar to surface corrosion of metals. Therefore, we postulate that NMR spectroscopy and X-ray diffraction, which are well-suited for bulk analysis, are less suited than Raman spectroscopy to observe the surface-based reactions that occur to UF 4 when exposed to humid air. Considering the importance of UF 4 in the production of nuclear fuel and weapons, the results presented herein are widely applicable to numerous nuclear science fields where uranium detection and speciation in humid environments is of value, including nuclear nonproliferation and nuclear forensics.
Much of what is known about high-temperature cuprate superconductors stems from studies based on two surface analytical tools, angle-resolved photoemission spectroscopy (ARPES) and spectroscopic imaging scanning tunneling microscopy (SI-STM). A question of general interest is whether and when the surface properties probed by ARPES and SI-STM are representative of the intrinsic properties of bulk materials. We find this question is prominent in thin films of a rarely studied cuprate Dy Ba 2 Cu 3 O 7 - δ DBCO). We synthesize DBCO films by oxide molecular beam epitaxy and study them by in situ ARPES and SI-STM. Both ARPES and SI-STM show that the surface DBCO layer is different from the bulk of the film—it is heavily underdoped, while the doping level in the bulk is close to optimal doping evidenced by bulk-sensitive mutual inductance measurements. ARPES shows the typical electronic structure of a heavily underdoped CU O 2 plane and two sets of one-dimensional bands originating from the CuO chains with one of them gapped. SI-STM reveals two different energy scales in the local density of states, with one (at ~ 18 meV ) corresponding to the superconductivity and the other one (at ~ 90 meV ) to the pseudogap. Finally, while the pseudogap shows large variations over the length scale of a few nanometers, the superconducting gap is very homogeneous. This indicates that the pseudogap and superconductivity are of different origins.
Skyrmions in noncentrosymmetric materials are believed to occur due to the Dzyaloshinskii-Moriya interaction. By contrast, the skyrmion formation mechanism in centrosymmetric materials remains elusive. Here, in this work, we reveal the intrinsic electronic structure of the centrosymmetric GdRu 2 Si 2 by selectively measuring magnetic domains using angle-resolved photoemission spectroscopy (ARPES). We found robust Fermi surface (FS) nesting, consistent with the magnetic modulation q -vector detected by the previous resonant x-ray scattering measurements. The pseudogap opens at the nested FS portions, which vary for different magnetic domains. The anomalous pseudogap disconnects the FS to generate Fermi arcs with twofold symmetry. These results indicate that the Ruderman-Kittel-Kasuya-Yosida (RKKY) interaction plays a decisive role in generating the screw spin modulation responsible for the skyrmion formation in GdRu 2 Si 2 . Furthermore, we demonstrate the flexible nature of magnetism in GdRu 2 Si 2 by manipulating magnetic domains with magnetic field and temperature cyclings, providing potential future applications for data storage and processing devices.
The power of mineralogical analysis as a descriptive or predictive technique stems from the fact that only a few thousand minerals are known to occur in nature as compared to several hundred thousand inorganic compounds. Further, all of the known minerals have specific stability ranges in pressure, temperature, an composition. A specific knowledge of the mineralogy of a planets surface or interior therefore allows one to characterize the present or past conditions under which the minerals were formed or have existed. For the purposes of this paper, a slightly broader definition of mineralogy was adopted by including not only crystalline materials found on planetary surfaces, but also ices and classes that can benefit from in situ types of analyses. Both visual examination and the various spectroscopies available for robotic probes to planetary surfaces are discussed.
Investigation of isolated, single atoms on the surfaces of alloys is of great interest in the field of heterogeneous catalysis. Prior studies by Nieuwenhuys, etal. [Surf. Sci. 417 (1998) 292–300 and references therein] showed that annealing the (111) surface of a PdAg bulk alloy yielded a surface with ~5% Pd, predominantly in the form of single atoms, rendering it an ideal model for investigating the reactivity of single Pd atoms. Herein, new evidence is reported that establishes the bulk composition of the PdAg(111) alloy studied previously is 67 % Ag and 33 % Pd, whereas it was reported to be 33 % Ag and 67 % Pd in the prior studies. Furthermore, the bulk composition of a crystal derived from the same PdAg alloy boule used previously was determined using energy-dispersive X-ray spectroscopy (EDS)—a bulk sensitive technique. Surface-sensitive measurements, including X-ray photoelectron spectroscopy, were also performed and are in good agreement with the prior studies by Nieuwenhuys, etal.
Here, we study the adsorption of methanol vapor under ambient pressure and temperature conditions on low-index Cu surfaces using surface-sensitive infrared (IR) and X-ray spectroscopy techniques. The first step of methanol decomposition, i.e. , breaking of the O—H bond to form surface-bound methoxy, readily occurs under ambient conditions. Time-lapse IR spectra clearly indicate a gradually decreasing methoxy coverage, which does not obey well established kinetic models. We rationalize the initial temperature-independent, high, nonequilibrium coverage of methoxy by a H-bonded methanol assembly in the precursor state. A temperature-dependent equilibrium coverage is achieved as the excess methoxy is eliminated gradually via further dehydrogenation to CO that desorbs to the gas phase. The kinetics of this process displays a significant structure sensitivity with considerably faster kinetics on the Cu(110) surface compared to Cu(111) and Cu(100) surfaces.
Hypothesis : Understanding the rules that control the assembly of nanostructured soft materials at interfaces is central to many applications. We hypothesize that electrolytes can be used to alter the hydration shell of amphiphilic oligomers at the air-aqueous interface of Langmuir films, thereby providing a means to control the formation of emergent nanostructures. Experiments : Three representative salts – (NaF, NaCl, NaSCN) were studied for mediating the self-assembly of oligodimethylsiloxane methylimidazolium (ODMS-MIM + ) amphiphiles in Langmuir films. The effects of the different salts on the nanostructure assembly of these films were probed using vibrational sum frequency generation (SFG) spectroscopy and Langmuir trough techniques. Experimental data were supported by atomistic molecular dynamic simulations. Findings : Langmuir trough surface pressure – area isotherms suggested a surprising effect on oligomer assembly, whereby the presence of anions affects the stability of the interfacial layer irrespective of their surface propensities. In contrast, SFG results implied a strong anion effect that parallels the surface activity of anions. These seemingly contradictory trends are explained by anion driven tail dehydration resulting in increasingly heterogeneous systems with entangled ODMS tails and appreciable anion penetration into the complex interfacial layer comprised of headgroups, tails, and interfacial water molecules. These findings provide physical and chemical insight for tuning a wide range of interfacial assemblies.
Yttrium-modified dealuminated Betazeolite (Y-BEA) represents a type of Lewis acid zeolite that has gained attention for its potential to efficiently catalyze the conversion of biomass-derived oxygenates. The structure of the Y active sites and their dynamics during biomass conversion reactions, which normally involve substantial amounts of water, necessitate thorough investigation for the rational design of more active and stable catalysts. Here, we conducted a study where a series of Y-BEA catalysts with different yttrium loadings (1–7 wt.%) were subjected to hydrothermal treatment (450 °C, 20% water) and investigated for their structural and catalytic activity changes through a combination of multiple characterizations and kinetic measurements. The number of acid sites of Y-BEA decreased without a change in acid strength following the hydrothermal treatment, which was confirmed by the results of acid site titration, infrared spectroscopy of probe molecules, and kinetic measurements for probe reactions (acetone aldol condensation). Structural analysis using X-ray diffraction (XRD), specific surface area measurement, X-ray absorption spectroscopy (XAS), and X-ray photoelectron spectroscopy (XPS) demonstrated that both the zeolite structure and the isolation status of the Y site remain intact after hydrothermal treatment. Further, the Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS) spectra, thermogravimetric analysis (TGA), and operando 1 H and 29 Si magic-angle spinning (MAS) nuclear magnetic resonance (NMR) revealed the dehydroxylation of Y-BEA induced by hydration-rearrangement-condensation restructuring during the high-temperature steam treatment. Dehydroxylation affects the structure of Y sites by reducing their vicinal silanol sites. In conclusion, this conversion of Lewis acidic Y sites into nonacidic sites is the primary factor behind the change in acid site quantity and catalytic activity on Y-BEA.
The second-order Moller-Plesset ab initio electronic structure method is used to compute points for the anharmonic mode-coupled potential energy surface of N-methylacetamide (NMA) in the trans(sub ct) configuration, including all degrees of freedom. The vibrational states and the spectroscopy are directly computed from this potential surface using the Correlation Corrected Vibrational Self-Consistent Field (CC-VSCF) method. The results are compared with CC-VSCF calculations using both the standard and improved empirical Amber-like force fields and available low temperature experimental matrix data. Analysis of our calculated spectroscopic results show that: (1) The excellent agreement between the ab initio CC-VSCF calculated frequencies and the experimental data suggest that the computed anharmonic potentials for N-methylacetamide are of a very high quality; (2) For most transitions, the vibrational frequencies obtained from the ab initio CC-VSCF method are superior to those obtained using the empirical CC-VSCF methods, when compared with experimental data. However, the improved empirical force field yields better agreement with the experimental frequencies as compared with a standard AMBER-type force field; (3) The empirical force field in particular overestimates anharmonic couplings for the amide-2 mode, the methyl asymmetric bending modes, the out-of-plane methyl bending modes, and the methyl distortions; (4) Disagreement between the ab initio and empirical anharmonic couplings is greater than the disagreement between the frequencies, and thus the anharmonic part of the empirical potential seems to be less accurate than the harmonic contribution;and (5) Both the empirical and ab initio CC-VSCF calculations predict a negligible anharmonic coupling between the amide-1 and other internal modes. The implication of this is that the intramolecular energy flow between the amide-1 and the other internal modes may be smaller than anticipated. These results may have important implications for the anharmonic force fields of peptides, for which N-methylacetamide is a model.
This study was conducted to evaluate the impact of dwell time, surface roughness, and the surface activation state on 1,1,1-trichloroethane's (TCA's) effectiveness for removing silicone oil from D6ac steel. Silicone-contaminated test articles were washed with TCA solvent, and then the surfaces were analyzed for residue, using Fourier transform infrared spectroscopy. The predominant factor affecting the ability to remove the silicone oil was surface roughness.
Continuous counter‐current microfluidic liquid–liquid extraction performs separations by flowing immiscible liquids in opposing directions within a single flow channel. In principle, this flow arrangement enables a large number of theoretical separation units in a small footprint, without using interstage valving, pumping, and phase separation. Despite its potential for excellent separation performance, this microfluidic scheme rarely appears in literature due to the requirement for capillary forces to be greater than hydrodynamic forces for stable flow. We present a novel microfluidic device and flow approaches that overcome this force‐balance challenge, enabling stable, long‐duration continuous counter‐current flow. Additionally, we cover a suite of methodologies for quantifying the performance of the microfluidic device, revealing the number of theoretical equilibrium stages achieved. The enabling technologies include a woven mesh screen‐based microfluidic device architecture that is easily fabricated outside of a clean room, surface functionalization strategies to promote conjugate (organic/aqueous) wettability, flow approaches to eliminate bubbles and carryover, and computer‐aided flow automation with optical measurement of extraction performance. The reported experiments lasted for over 36 h, terminated only at experiment conclusion, where the device still exhibited good performance. Automated Raman spectroscopy was used for solute quantitation of the ternary system tert‐butanol in a toluene/water matrix, a ternary system that was specifically chosen to analyze the device's performance with a small solute partition ratio and to enable in‐line Raman measurements of solute concentrations in both phases. The microfluidic device possessed a 55 mm contact length and a 38.5 µL internal volume. During counter‐current flow, we observed approximately 37 equilibrium stages (37 ± 13) based on a best‐fit of the solute fraction remaining in the aqueous phase using a Kremser Group Method analysis.
Cerium oxide (CeO 2 ) and ceria-based materials have been extensively investigated as catalyst and support materials for various catalytic reactions, due to higher oxygen storage capacity and excellent redox properties. In the current work, we investigated the impact of pretreatment conditions (e.g., oxidation and reduction) on the physical properties of bulk CeO 2 and catalytic activity for CO oxidation as a model reaction. To understand the physical properties of pretreated CeO 2 catalysts, a suite of complementary characterization techniques, including X-ray diffraction (XRD), surface area analysis (BET), X-ray photoemission spectroscopy (XPS), and Raman spectroscopy, were applied. The results showed that a higher pretreatment temperature led to a decreased specific surface area (SSA), a decrease in oxygen vacancy/defect sites, and increased crystallite size, while surface Ce 3+ /Ce 4+ ratio did not show a specific relationship to the treatment conditions. The 700 °C treated CeO 2 samples under oxidizing and reducing conditions showed higher specific oxidation rate (μmolCO/s/m 2 ) compared to other samples at 280 and 300 °C (or < 15% CO conversion). The CO conversion per total mass of catalysts, however, decreased with increasing temperatures, especially at 700 °C under reducing condition, indicating that the catalytic performance was affected by the physical properties (SSA, oxygen vacancy/defect sites, and crystallite size).
Electrocoagulation (EC) of synthetic groundwater was conducted using a sacrificial aluminum electrode in a flow-through EC reactor with short retention times (<1 min) under varying hydrodynamic and electrochemical conditions. The treated water was allowed to settle for 24 h and achieved silicate removal of up to 50 ± 4%, and hardness removal of 11 ± 1%. Physical, chemical, and electrochemical characterization was performed to explore changes in electrode surface morphology and composition. Electrochemical impedance spectroscopy (EIS) showed that chemical reactions at the electrode/water interface are sensitive to changes in the immediate chemical environment. We demonstrate that the most energy-intensive step in EC is aluminum dissolution at the anode, which remained fairly constant due to the continuous renewal of the anode’s surface, a result of aluminum dissolution. At the cathode, a structural change in the oxide layer, from γ-Al 2 O 3 to gibbsite, was detected by grazing-incidence X-ray diffraction, which decreased the resistance to charge transfer at the cathode surface, resulting in decreased electrode resistance. The high flow rate in the system minimized the accumulation of aluminum hydroxide solids and aluminum ions at the electrode/water interface, which minimized the formation of thick scalants and amorphous Al(OH) 3 on the cathode and anode, respectively. In conclusion, it was further demonstrated by EIS that under these conditions the resistance to charge transfer was constant throughout the duration of the experiment.
SmB 6 is a strongly correlated material that has been attributed as a topological insulator and a Kondo insulator. Recent studies have found the topological surface states and low temperature insulating character to be profoundly robust against magnetic and nonmagnetic impurities. Here, we use angle resolved photoemission spectroscopy to chart the evolution of topologically linked electronic structure features versus magnetic doping and temperature in Sm 1-$x$ M $x$ B 6 ( M =Eu, Ce). Topological coherence phenomena are observed out to ~30% Eu and 50% Ce concentrations that represent extreme nominal hole and electron doping, respectively. Finally, theoretical analysis reveals that a recent redesignation of the topologically inverted band symmetries provides a natural route to reconciling the persistence of topological surface state emergence even as the insulating gap is lost through decoherence.
Interfacial behaviors and properties play critical roles in determining key practical parameters of electrochemical energy storage systems, such as lithium-ion and sodium-ion batteries. Soft x-ray spectroscopy features shallow penetration depth and demonstrates inherent surface sensitivity to characterize the interfacial behavior with elemental and chemical sensitivities. Here, we present a brief survey of modern synchrotron-based soft x-ray spectroscopy of the interface in electrochemical energy storage systems. The technical focus includes core-level spectroscopy of conventional x-ray absorption spectroscopy and resonant inelastic x-ray scattering (RIXS). We show that while conventional techniques remain powerful for probing the chemical species on the surface, today’s material research studies have triggered much more demanding chemical sensitivity that could only be offered by advanced techniques such as RIXS. Another direction in the field is the rapid development of various in situ/operando characterizations of complex electrochemical systems. Notably, the solid-state battery systems provide unique advantages for future studies of both the surface/interface and the bulk properties under operando conditions. We conclude with perspectives on the bright future of studying electrochemical systems through these advanced soft x-ray spectroscopic techniques.
Here, manganese antimonates are earth-abundant potential alternatives to precious metal catalysts for the oxygen-evolution reaction (OER). Herein, X-ray photoelectron spectroscopy was used to determine the surface chemistry of a manganese antimonate catalyst for the OER under ultra-high vacuum, ambient pressure, and in situ reaction conditions. Ex situ and in situ analysis revealed the oxidation states of surficial species as a function of material stoichiometry, water content, and applied potential. In situ XPS measurements in 1.0 M KOH(aq) indicated that relative to the rest state, the surface Mn(III) partially oxidized while effecting the OER, with approximately 15% of the Mn signal attributable to Mn(IV) and the remainder attributable to Mn(III).
An approximate analytic solution is derived for the radiative transfer equation describing particulate surface light scattering, taking into account multiple scattering and mutual shadowing. Analytical expressions for the following quantities are found: bidirectional reflectance, radiance coefficient and factor, the normal, Bond, hemispherical, and physical albedos, integral phase function and phase integral, and limb-darkening profile. Scattering functions for mixtures can be calculated, as well as corrections for comparisons of experimental transmission or reflection spectra with observational planetary spectra. The theory should be useful for the interpretation of reflectance spectroscopy of laboratory surfaces and the photometry of solar system objects.