Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strong motion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Structural dynamics studies of rotating bladed-disk assemblies coupled with flexible shaft motions

In order to analyze the dynamic behavior of the first stage compressor/fan of the 'E3' turbofan engine, a classical structural dynamics approach is employed to couple the motions of a flexible bladed disk to a rotating flexible shaft. The analysis accounts for flexible disk displacements which are transverse to the plane of rotation, and radial as well as tangential, and also accounts for rigid disk translations along, and rotations about, axes normal to the undeformed shaft axes. In the case of a wide range of E3 engine shaft flexibilities and speeds, some of the one-diametral node frequencies are shown to be affected by shaft degrees of freedom whose stiffness values are in general range of design practice. Coriolis forces are also found to significantly affect natural frequencies where strong coupling between certain modes is present.

Loewy, R. G.↗

Analytic and numerical models of wave-CISK with conditional heating

Wave-CISK with conditional heating is investigated in the equatorial zonal-height plane by analytic and numerical techniques. For two- and three-level models, previous results are extended to give additional evidence that the most unstable mode has a single wet region of infinitesimal width. A three-level model has qualitatively similar behavior as the two-level model except that propagating solutions are possible due to coalescence of internal vertical modes. Phase speeds with conditional heating are found to be slightly greater than those for unconditional heating. The structure has one circulation cell in the vertical and is asymmetric in longitude with stronger motion on the leading edge. Growth rate is inversely proportional to the width of the single wet region. That width can be limited by second-order diffusion. A general integral relationship between growth rate, viscosity, phase speed, and heating is derived. The main conclusion is that the linear wave-CISK catastrophe is modified by conditional heating but not eliminated. The preferred mode of instability has one wet region, but it occurs on the smallest possible scale. It is likely that numerical models that use conditional heating are sensitive to resolution, especially for the commonly used spectral truncations, unless there is sufficiently strong damping at the smallest scales.

Crum, Francis X.↗

The Origin and Distribution of Heavy Elements in the CD Groups MKW 4 and AWM 4

At this point, data for MKW4 have been received and those for AWM4 are still awaited. The MKW4 data have been fully analyzed and a complete manuscript is available and in final review by co-authors before submission for refereed publication. The following is a summary of our principal findings: We examined the distribution and properties of the hot gas which makes up the group halo. The inner halo shows some signs of structure, with circular or elliptical beta-models providing a poor fit to the surface brightness profile. This may be evidence of large-scale motion in the inner halo, but we do not find evidence of sharp fronts or edges in the emission. The temperature of the halo declines in the core, with deprojected spectral fits showing a central temperature of approximately 1.3keV compared to approximately 3keV at 250 arcsec. However, cooling flow models provide poor fits to the inner regions of the group and the estimated cooling time of the gas is long except within the central dominant galaxy, NGC4073. Abundance profiles show a sharp increase in the core of the group. We conclude that MKW4 is a fairly relaxed group, which has developed a strong central temperature gradient but not a large-scale cooling flow.

Vrtilek, Jan↗

Numerical simulations of the Ross Sea tides

Tidal currents below the floating Ross Ice shelf are reconstructed by using a numerical tidal model. They are predominantly diurnal, achieve maximum strength in regions near where the ice shelf runs aground, and are significantly enhanced by topographic Rossby wave propagation along the ice front. A comparison with observations of the vertical motion of the ice shelf surface indicates that the model reproduces the diurnal tidal characteristics within 20 percent. Similar agreement for the relatively weak semidiurnal tides was not obtained, and this calls attention to possible errors of the open boundary forcing obtained from global-ocean tidal simulations and to possible errors in mapping zones of ice shelf grounding. Air-sea contact below the ice shelf is eliminated by the thick ice cover. The dominant sub-ice-shelf circulation may thus be tidally induced. A preliminary assessment of sub-ice-shelf conditions based on the numerical tidal simulations suggests that (1) strong barotropic circulation is driven along the ice front and (2) tidal fronts may form in the sub-ice-shelf cavity where the water column is thin and where the buoyancy input is weak.

Macayeal, D. R.↗

Effect of large amplitude pitching motions on the unsteady aerodynamic characteristics of flat-plate wings

Large-amplitude unsteady motion effects on the aerodynamic force and stability characteristics of flat-plate wings were investigated in a wind tunnel for the cases of two delta wings with respective leading edge sweeps of 70 and 45 deg, and a rectangular wing whose aspect ratio was equal to that of the 70-deg delta wing. Attention was given to the effects of reduced frequency and mean angle of attack. It is found that lags in vortex burst location and separation/reattachment of flow on the upper surface of the wing produced large overshoots and hysteresis loops in normal force and pitching moment coefficients that were a strong function of mean oscillation angle and reduced frequency.

Brandon, Jay M.↗

A determination of the external forces required to move the benchmark active controls testing model in pure plunge and pure pitch

In view of the strong need for a well-documented set of experimental data which is suitable for the validation and/or calibration of modern Computational Fluid Dynamics codes, the Benchmark Models Program was initiated by the Structural Dynamics Division of the NASA Langley Research Center. One of the models in the program, the Benchmark Active Controls Testing Model, consists of a rigid wing of rectangular planform with a NACA 0012 profile and three control surfaces (a trailing-edge control surface, a lower-surface spoiler, and an upper-surface spoiler). The model is affixed to a flexible mount system which allows only plunging and/or pitching motion. An approximate analytical determination of the forces required to move this model, with its control surfaces fixed, in pure plunge and pure pitch at a number of test conditions is included. This provides a good indication of the type of actuator system required to generate the aerodynamic data resulting from pure plunging and pure pitching motion, in which much interest was expressed. The analysis makes use of previously obtained numerical results.

Dcruz, Jonathan↗

An evaluation of the effects of stacking sequence and thickness on the fatigue life of quasi-isotropic graphite/epoxy laminates

Notched and unnotched geometries at 16, 32, and 64-ply thicknesses of a 90/45/0-45 (ns) laminate and a 45/0/-45/90 (ns) laminate were tested in compression-compression fatigue. The fatigue life and the initiation, type, and progression of damage were determined. Interlaminar stresses generated at straight, free edges of axially loaded laminates were used to interpret the test results. The fatigue lives of the notched specimens did not appear to be a strong function of laminate stacking sequence or specimen thickness. The stress concentration at the hole dominated over the interlaminar stresses at the straight free edge. The unnotched specimens of the 90/45/0/-45 (ns) laminate with tensile interlaminar normal stresses delaminated more readily than did the 45/0/-45/90 (ns) laminate with compressive interlaminar normal stress. The life of the 16-ply unnotched specimens was lower than the 32and 64-ply specimens. Delaminations were located at the interface where the maximum shear stress occurred regardless of the sense or magnitude of the interlaminar normal stress. An antibuckling fixture was effective in preventing out-of-plane motion without overconstraining the specimen.

Harris, C. E.↗

Consistency Between Divergent Circulations from Reanalysis Data Sets and Satellite-Derived Precipitation, Radiation, and Surface Fluxes

Large-scale divergent circulations are part of the atmospheric dynamic response to diabatic heating from condensation, radiative processes, and surface heat fluxes. Vertical motion and the associated divergent wind is thus intimately tied to the hydrologic cycle and the global heat balance. Despite its importance, the divergent circulation is too small in comparison to the rotational flow to measure directly with any accuracy. Vertical motions are recovered diagnostically from reanalyses and, as such, are subject to shortcomings in model physics, numerics, and data availability. We use several GEWEX pre-EOS data sets derived from satellite data to assess interannual divergent flow anomalies in the NCEP, GSFC, and GSFC DAO analyse. Among the data sets are monthly, 2.5 degree gridded precipitation (MSU and SSM/I-based), TOA radiative fluxes from ERBS, surface radiative fluxes from the SRB project, and surface latent and sensible flux estimates from SSM/I. Most of these data sets can be considered as independent of the reanalysis fields. We focus largely on the period 1987-1989 encompassing a strong El Nino / la Nina couplet. Consequently we emphasize interannual changes rather than climatological aspects of the reanalyses. In the processes of this study we use simple integral constraints enforced through the satellite-derived data sets to derive corrections to the divergent circulation produced from the reanalyses. We examine the implications of these corrections in describing how perturbations to the tropical heat balance evolve during a warm / cool couplet. In particular the perturbations to the planetary scale water vapor transport, and the resulting changes in TOA and surface radiative fluxes are considered.

Robertson, Franklin R.↗

An evaluation of the effects of stacking sequence and thickness on the fatigue life of quasi-isotropic graphite/epoxy laminates

Notched and unnotched geometries at 16, 32, and 64-ply thicknesses of a 90/45/0-45 (ns) laminate and a 45/0/-45/90 (ns) laminate were tested in compression-compression fatigue. The fatigue life and the initiation, type, and progression of damage were determined. Interlaminar stresses generated at straight, free edges of axially loaded laminates were used to interpret the test results. The fatigue lives of the notched specimens did not appear to be a strong function of laminate stacking sequence or specimen thickness. The stress concentration at the hole dominated over the interlaminar stresses at the straight free edge. The unnotched specimens of the 90/45/0/-45 (ns) laminate with tensile interlaminar normal stresses delaminated more readily than did the 45/0/-45/90 (ns) laminate with compressive interlaminar normal stress. The life of the 16-ply unnotched specimens was lower than the 32- and 64-ply specimens. Delaminations were located at the interface where the maximum shear stress occurred regardless of the sense or magnitude of the interlaminar normal stress. An antibuckling fixture was effective in preventing out-of-plane motion without overconstraining the specimen.

Harris, C. E.↗

Computing high-speed flows past an oscillating cylinder near a vertical wall

A computational method to simulate unsteady flows involving moving rigid boundaries and interference has been developed. The method is used to solve inviscid equations governing the fluid flow and the dynamic equations governing the motion of rigid bodies. A second-order accurate, upwind-biased, and alterating-direction-implicit method is used to solve the governing equations of the flow. A kinematic domain decomposition (KDD) procedure is extended to treat 3D problems with a high degree of accuracy and generality. The method under consideration is applied to both transonic and supertransonic flows. Both cases involve flow past a cylinder which is forced to pitch sinusoidally near a vertical wall. Benefits of the proposed approach include accurate calculation of the flow around 3D moving multiple bodies with interference; reduction of a numerical error; in particular, the dispersion error which strongly affects wave propagation; and minimization of the phase error which is accumulated according to the time advance procedure.

Yen, Guan-Wei↗

Solar cycle variations in the size and shape of the magnetopause

The 10 years of the ISEE 1 and 2 mission covering much of solar cycle 21 and the beginning of solar cycle 22 make it possible to study the position, shape, and motion of the magnetopause throughout the course of changing solar activity. The size and shape of the magnetopause were determined for each observing season using the ISEE 1 and 2 magnetometer data IMP 8 data were used to monitor the solar wind changes with the solar cycle. During the 1979-1980 season, at solar maximum, the solar wind dynamic pressure was at its lowest values, and, at solar minimum, the solar wind pressure was at its largest values, more than double the value in the 1979-1980 season. During this solar cycle, the magnetopause was about 0.5 R(E) farther when the interplanetary magnetic field (IMF) was strongly northward, than when strongly southward. Both standoff distance values are fround to be smaller than the value found by Fairfield (1971). The standoff distance of the magnetopause for northward IMF is anticorrelated with the solar wind pressure. However, the standoff distance for southward IMF seems relatively insensitive to solar wind dynamic pressure.

Petrinec, S. P.↗

Role of the Quasi-Biennial Oscillation in the Transport of Aerosols from the Tropical Stratospheric Reservoir to Midlatitudes

The temporal evolution of the stratospheric aerosol distribution in the tropical stratospheric reservoir after the eruption of Mount Pinatubo was observed from 1992 to 1995 by the HALOE instrument on the UARS satellite. Since the spatial gradient of aerosol loading is large at the boundaries of the tropical stratospheric reservoir due to the volcanic aerosols, the effect of the meridional circulation on the distribution is seen clearly. The mechanism for dispersal of aerosol in the lower stratosphere from the tropics into midlatitudes strongly depends on the phase of the equatorial zonal wind. The time-latitude cross sections of the normalized distribution of aerosol on isentropic surfaces are used to observe the equatorial variation as well as change in meridional dispersal during the quasi-biennial period. Observed tropical stratospheric winds are used with a simple analytical dynamical model to examine transport processes of tracers from the tropics during several phases of the quasi-biennial oscillation (QBO) from 1992 to 1995. The Lagrangian meridional circulation in the tropics is consistent with the vertical and meridional velocities correlated with the QBO in the zonal wind. We find that vertical motion plays a crucial role in vertical and subsequent meridional transport. The pattern of meridional divergence derived from the vertical velocity is closely related to the observed HALOE aerosol distributions and their temporal development in the equatorial region. The westerly (easterly) shear phase of the QBO is associated with sinking (rising) motions at the equator and subsequent poleward (equatorward) transport in the lower stratosphere.

Choi, Wookap↗

Improving our Understanding of Atlantic Tropical Cyclones through Knowledge of the Saharan Air Layer: Hope or Hype?

The existence of the Saharan air layer (SAL), a layer of warm, dry, dusty air that frequently moves westward off of the Saharan desert of Africa and over the tropical Atlantic Ocean, has long been appreciated. As air moves over the desert, it is strongly heated from below, producing a very hot air mass at low levels. Because there is no moisture source over the Sahara, the rise in temperature causes a sharp drop in relative humidity, thus drying the air. In addition, the warm air produces a very strong jet of easterly flow in the middle troposphere called the African easterly jet that is thought to play a critical role in hurricane formation. In recent years, there has been an increased focus on the impact that the SAL has on the formation and evolution of hurricanes in the Atlantic. However, the nature of its impact remains unclear, with some researchers arguing that the SAL amplifies hurricane development and with others arguing that it inhibits it. The argument for positively influencing hurricane development is based upon the fact that the African easterly jet produces the waves that eventually form hurricanes and that it leads to rising motion south of the jet that favors the development of deep thunderstorm clouds. The potential negative impacts of the SAL include 1) low-level vertical wind shear associated with the African easterly jet; 2) warm SAL air aloft, which increases thermodynamic stability and suppresses cloud development; and 3) dry air, which produces cold downdrafts in precipitating regions, thereby removing energy needed for storm development. As part of this recent focus on the SAL and hurricanes (which motivated a 2006 NASA field experiment), there has been little emphasis on the SAL s potential positive influences and almost complete emphasis on its possible negative influences, almost to the point of claims that the SAL is the major suppressing influence on hurricanes in the Atlantic. Multiple NASA satellite data sets (TRMM, MODIS, and AIRS/AMSU) and National Centers for Environmental Prediction global analyses are used to characterize the SAL s properties and evolution in relation to developing hurricanes. The results show that storms generally form on the southern side of the jet, where favorable background rotation is high. The jet often helps to form the northern side of the storms and rarely moves over their inner cores, so jet-induced vertical wind shear does not appear to be a negative influence on developing storms. Warm SAL air is confined to regions north of the jet and generally does not impact the tropical cyclone precipitation south of the jet. Of the three proposed negative influences, dry air appears to be the key influence; however, the presence of dry SAL air is not a good indicator of whether a storm will weaken since many examples of intensifying storms surrounded by such dry air can be found. In addition, a global view of relative humidity shows moisture distributions in other ocean basins that are almost identical to the Atlantic. The dry zones correspond to regions of descending air on the eastern and equatorward sides of semi-permanent oceanic high pressure systems. Thus, the dry air over the Atlantic appears to be primarily a product of the large-scale flow, but with enhanced drying at low levels associated with the Sahara. As a result, we conclude that the SAL is not a major negative influence on hurricanes. It is just one of many possible influences and can be both positive and negative.

Braun, Scott A.↗

Bare Conductive Tether for Decelerating a Spacecraft

A document describes a prototype of electrically conductive tethers to be used primarily to decelerate spacecraft and/or generate electric power for the spacecraft. Like prior such tethers, this tether is designed so that when it is deployed from a spacecraft in orbit, its motion across the terrestrial magnetic field induces an electric current. The Lorentz force on the current decelerates the spacecraft. Optionally, the current can be exploited to convert some orbital kinetic energy to electric energy for spacecraft systems. Whereas the conductive portions of prior such tethers are covered with electrical insulation except for end electrodes that make contact with the ionosphere, this tether includes a conductive portion that is insulated along part of its length but deliberately left bare along a substantial remaining portion of its length to make contact with the ionosphere. The conductive portions of the tether are made of coated thin aluminum wires wrapped around strong, lightweight aromatic polyamide braids. The main advantages of the present partly-bare-tether design over the prior all-insulated-tether design include greater resistance to degradation by the impact of monatomic oxygen at orbital altitude and speed and greater efficiency in collecting electrons from the ionosphere.

Johnson, Les↗

Vortex shedding from a blunt trailing edge with equal and unequal external mean velocities

A flow-visualization study has shown that strong Karman vortices develop behind the blunt trailing edge of a plate when the free-stream velocities over both surfaces are equal and that the vortices tend to disappear when the surface velocities are unequal. This observation provides an explanation for the occurence and disappearance of certain discrete tones often found to be present in the noise spectra of coaxial jets. Both the vortex formation and the tones occur at a Strouhal number based on the lip thickness and the average of the external steady-state velocities of about 0.2. Results from theoretical calculations of the vortex formation, based on an inviscid incompressible analysis of the motion of point vortices, were in good agreement with the experimental observations.

Boldman, D. R.↗

Diagnostics of vector magnetic fields

It is shown that the vector magnetic fields derived from observations with a filter magnetograph will be severely distorted if the spatially unresolved magnetic structure is not properly accounted for. Thus the apparent vector field will appear much more horizontal than it really is, but this distortion is strongly dependent on the area factor and the temperature line weakenings. As the available fluxtube models are not sufficiently well determined, it is not possible to correct the filter magnetograph observations for these effects in a reliable way, although a crude correction is of course much better than no correction at all. The solution to this diagnostic problem is to observe simultaneously in suitable combinations of spectral lines, and/or use Stokes line profiles recorded with very high spectral resolution. The diagnostic power of using a Fourier transform spectrometer for polarimetry is shown and some results from I and V spectra are illustrated. The line asymmetries caused by mass motions inside the fluxtubes adds an extra complication to the diagnostic problem, in particular as there are indications that the motions are nonstationary in nature. The temperature structure appears to be a function of fluxtube diameter, as a clear difference between plage and network fluxtubes was revealed. The divergence of the magnetic field with height plays an essential role in the explanation of the Stokes V asymmetries (in combination with the mass motions). A self consistent treatment of the subarcsec field geometry may be required to allow an accurate derivation of the spatially averaged vector magnetic field from spectrally resolved data.

Stenflo, J. O.↗

Co-Seismic Mass Displacement and its Effect on Earth's Rotation and Gravity

Mantle processes often involve large-scale mass transport, ranging from mantle convection, tectonic motions, glacial isostatic adjustment, to tides, atmospheric and oceanic loadings, volcanism and seismicity. On very short time scale of less than an hour, co-seismic event, apart from the "shaking" that is the earthquake, leaves behind permanent (step-function-like) displacements in the crust and mantle. This redistribution of mass changes the Earth's inertia tensor (and hence Earth's rotation in both length-of-day and polar motion), and the gravity field. The question is whether these effects are large enough to be of any significance. In this paper we report updated calculation results based on Chao & Gross. The calculation uses the normal mode summation scheme, applied to over twenty thousand major earthquakes that occurred during 1976-2002, according to source mechanism solutions given by the Harvard Centroid Moment Tensor catalog. Compared to the truly large ones earlier in the century, the earthquakes we study are individually all too small to have left any discernible signature in geodetic records of Earth rotation or global gravity field. However, their collective effects continue to exhibit an extremely strong statistical tendencies, conspiring to decrease J2 and J22 while shortening LOD, resulting in a rounder and more compact Earth. Strong tendency is also seen in the earthquakes trying to "nudge" the Earth rotation pole towards approx. 140 deg.E, roughly opposite to the observed polar drift direction. Currently, the Gravity Recovery And Climate Experiment (GRACE) is measuring the time-variable gravity to high degree and order with unprecedented accuracy. Our results show that great earthquakes such as the 1960 Chilean or 1964 Alaskan events cause gravitational field changes that are large enough to be detected by GRACE.

Chao, B. F.↗

Translocation of a Polymer Chain across a Nanopore: A Brownian Dynamics Simulation Study

We carried out Brownian dynamics simulation studies of the translocation of single polymer chains across a nanosized pore under the driving of an applied field (chemical potential gradient). The translocation process can be either dominated by the entropic barrier resulted from restricted motion of flexible polymer chains or by applied forces (or chemical gradient across the wall), we focused on the latter case in our studies. Calculation of radius of gyrations at the two opposite sides of the wall shows that the polymer chains are not in equilibrium during the translocation process. Despite this fact, our results show that the one-dimensional diffusion and the nucleation model provide an excellent description of the dependence of average translocation time on the chemical potential gradients, the polymer chain length and the solvent viscosity. In good agreement with experimental results and theoretical predictions, the translocation time distribution of our simple model shows strong non-Gaussian characteristics. It is observed that even for this simple tubelike pore geometry, more than one peak of translocation time distribution can be generated for proper pore diameter and applied field strengths. Both repulsive Weeks-Chandler-Anderson and attractive Lennard-Jones polymer-nanopore interaction were studied, attraction facilitates the translocation process by shortening the total translocation time and dramatically improve the capturing of polymer chain. The width of the translocation time distribution was found to decrease with increasing temperature, increasing field strength, and decreasing pore diameter.

Tian, Pu↗