Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

A Comparative Study on Representativeness and Stochastic Efficacy of Miniature Tensile Specimen Testing

Here, in this article, a miniature dog bone tensile coupon design was tested against the existing ASTM standard specimen design. Specimens were prepared from commercially sourced austenitic stainless steel 304 alloy, and a defect-ridden additively manufactured 304L alloy was studied. By utilizing a tensile specimen design that is 1/230th volume of the smallest ASTM E8-04(2016), Standard Test Methods for Tension Testing of Metallic Materials, dog bone specimen, coupled to a digital image correlation (DIC) setup, case studies were performed to compare tensile property measurements and strain field evolution. Whereas yield strength measurements were observed to be similar, post-yield, the ultimate strength measurements and ductility measurements from the miniature specimens were observed to be higher than the ASTM specimen design. Although the strength measurements were comparable, the strain evolution was found to differ in the miniature specimens. Studies to assess effects of varying thickness and defect population were also pursued on the miniature tensile specimen. From the DIC strain field estimations, the peak local strain values at ultimate tensile strength were observed to be increasing with reducing specimen thickness. Testing of defect ridden stainless steel revealed the sensitivity to failure through strain localization and the influence of defect size was captured in the strength measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2020

IHS-60 Stored Energy Analysis

The IHS-60 consists of a General Purpose Heat Source (GPHS) Fueled Clad (FC) that has been hot isostatically pressed to eliminate the gap between the iridium clad and the fuel pellet, thus preventing differential motion between the pellet and the clad in shock and vibration environments. The vented FC is enclosed within a Molybdenum barrier comprising the liner body and the lower support member. The slip- t Molybdenum liner members serve as a mechanical barrier to plutonia contact of the tantalum alloy (T-111) strength member in the event the iridium clad should fail. The slip- t liner is not a barrier to gaseous transport, so a tantalum getter is installed near the vent region of the FC to preclude potential oxygen transport to the T-111 interior surface. The T-111 strength member encloses the Molybdenum liner assembly and provides for both helium gas retention and isotope fuel containment under impact and external pressure environments. It is surrounded by an outer clad of Hastelloy-S which protects the strength member from external oxidation and corrosive sources during nominal operation and in the event of off-nominal operation or accidents. Both the strength member and outer clad parts are closed with seal welds. The strength member and outer clad are the primary containment members of the 60-Watt IHS. The iridium clad contains the fuel pellet during nominal operation and mild accident environments, but it is not considered to be a primary containment member.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Progress Report on Performance of A709 and G91 Steels in Sodium

Specimens in six different processing and heat treatment conditions of A709 H58776 were exposed to sodium at 550, 600, and 650°C, respectively for various exposure times. G91 base metal was tested in sodium at 550, 600, and 650°C, and G91 weldment at 550 and 600°C, respectively. Parallel thermal aging experiments were conducted on G91 and A709 to obtain thermal aging data for comparison with sodium exposure results to separate the thermal and sodium effects. The corrosion data obtained on A709 steel continue to show low corrosion rates, which indicate good compatibility of A709 with sodium when oxygen content is controlled. G91 has also shown acceptable corrosion rates over the temperature range of 550-650°C in sodium. Thermal aging or sodium exposures reduced the tensile strength, uniform elongation, and total elongation for A709 ESR, AOD specimens. These specimens consistently showed higher yield stress and tensile strength and lower uniform and total elongations after sodium exposure than after thermal aging under comparable testing conditions. It implies that there was an additional effect of sodium exposure that gave rise to an increase in tensile strength of A709. Dynamic strain aginginduced flow serrations were completely removed by either thermal aging or sodium exposure at 650°C, which imply that carbon or nitrogen in solution was removed from the solution and formed precipitates during aging or sodium exposures. The tensile data ruled out the possibility of decarburization under the sodium exposure conditions. The HOMO specimens behaved somewhat differently from the ESR and AOD specimens in sodium. While thermal aging and sodium exposures at 550 and 600°C decreased the yield stress and the ultimate tensile strength of G91, there was virtually no additional effect resulting from sodium exposures at these two temperatures. In contrast, sodium exposures at 650°C had a drastic effect on the yield stress and the ultimate tensile strength of G91. It is suggested that G91 experienced decarburization in the 650°C sodium environments. Carbon concentrations in sodium in the SMT-1 and SMT-2 loops were determined by a foil equilibration method. The estimated carbon concentration was in the range of 0.8-1.2 ppm in the SMT-1 loop and 0.3-0.7 ppm in the SMT-2 loop. The carbon activity in sodium in the SMT-2 loop was estimated to be 0.03-0.08 at 600°C, and 0.08-0.2 at 550°C. The carbon activity in sodium at 650°C in the SMT-1 loop was 0.04-0.07. Equilibrium simulation of the carburization – decarburization processes was conducted for A709 and G91 steels exposed in sodium environments at temperatures of 550-700°C. The carbon activity-concentration relationship for G91 was re-evaluated by considering four phases in G91, i.e. bcc ferrite, M 23 C 6 , NbC and VC carbides. It was found that the carburization-decarburization process in G91 steel was dictated by M 23 C 6 carbides at high carbon activities, while NbC carbides dominated the process at low carbon activities. Formation of NbC increases the decarburization resistance of G91 steel. It remains to be understood whether the decarburization resistance provided by MC carbides in G91 can be maintained during long-term operations of SFRs. The carbon concentration-activity relationship for A709 was calculated based on the equilibrium of fcc-austenite and M 23 C 6 carbide phase. The calculations showed that A709 decarburizes at 650°C in the SMT-1 loop environments, which is different from the experimental findings. The carbon concentration-activity relationship in A709 was further evaluated by considering four phases, including fcc-austenite, M 23 C 6 , NbC, and TiC carbide phases. TiC is the most stable carbides among the three carbide phases. The carburization-decarburization process in A709 is dictated by M 23 C 6 carbides at high carbon activities and by TiC at low carbon activities. Formation of TiC increases the decarburization resistance of A709 steel. Because of the complexity of the precipitation process in A709 during sodium exposures, detailed characterization of precipitates in sodium-exposed specimens and improved thermodynamic models are needed to understand the carburization-decarburization behavior of A709. Kinetic analysis of carbon transfer will be investigated for G91 and A709 in future work.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

P- and S-Wave velocity and Indirect Tensile Measurements for Alluvium in Support of the Source Physics Experiments

Mechanical properties on alluvium blocks and core samples were determined to support the Source Physics Experiment Dry Alluvium Geology experimental series. Because material was not available directly from the experimental location, the alluvium blocks and core samples are intended to serve as surrogate material . P - and S - wave velocity was measured on cubes cut from the alluvium blocks and core with the intention to study variation from water content and measured direction (material anisotropy). Indirect tensile tests were conducted dry and with moisture ranging from 6 to 9.1%. For the range of water content tested, increasing moisture level resulted in slower P - and S - wave velocities. P - and S - wave variability is less influenced by material heterogeneity than moisture content. P - wave velocity ranges from 629 m/s to 2599 m/s and S - wave velocity ranges from 288 m/s to 1200 m/s. Counter to the velocity measurement findings, material variability on indirect tensile strength has a greater effect than moisture content. Compared to dry strength and at moisture levels from 6 to 9% the block's tensile strength was lowered by at least a factor of 5. Indirect tensile strength for the first block averaged 0.35 MPa and 0.25 MPa for dry and 8.9% moisture respectively. For the second block indirect tensile strength averaged 0.05 MPa for both dry and 6.4% moisture.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Coal-based Bricks & Blocks (CBBs): Process Development to Prototype Fabrication Coupled with Techno-Economic Analysis and Market Survey

The decline of coal use for energy production provides an abundance of local feedstock for new innovative uses and value-added products. Expanding the U.S. coal-value chain to manufacture high-value carbon products can strengthen the nation’s energy and mineral security, enhance the U.S. national defense security, increase the United States’ economic prosperity, while achieving U.S. environmental objectives. The primary project goal is a relatively light-weight composite product with superior (or comparable) compressive strength. Both virgin and, where available, post-consumer recycled thermoplastic versions are tested for each thermoplastic species. A useful attribute of thermoplastics as binders is that they can be heated to their melting point, cooled, and reheated again without significant degradation. A key advantage of thermoset CBBs is that they require only mixing and molding. CBB advantages include low cost, availability, binding ability and processability. Coal-based bricks and blocks (CBBs) weigh about 50% less than clay bricks and can be manufactured with an interlocking design to promote ease of use for the novice builder. CBB formulation is evaluated according to a design-of-experiments (DoE) approach. DoE variables are a) relative weight fractions of binder, b) relative proportions of large versus small (milled) anthracite size fractions, and c) additive percentage. Fabrication methods include hot-press molding and extrusion, the later being the most commercially viable. CBBs are tested for compressive strength, modulus of rupture (by flexure test) and water absorption per ASTM C67, with density determined by the Archimedes drainage method. Fractured interfaces are examined by SEM (Scanning Electron Microscopy) to resolve fracture dynamics and interior microstructure uniformity. Differential scanning calorimetry (DSC) is used to compare plastic transition temperatures i.e., glass and melting temperatures to contrast virgin with post-consumer recycled thermoplastics and optimize their usage. These results are used in the DoE analysis to identify the binder and relative weight percentages for optimum strength, density, and porosity. Overall, CBBs possess strength comparable to clay-based bricks but are non-permeable and hydrophobic, and hence resistant to degradation by freeze-fracturing, corrosion, and efflorescence. The strongest composites have been made with the following thermoplastic binders (in order of strength): thermoset, high-density polyethylene crosslink resin, high-density polyethylene, nylon 6/6, and polypropylene. Results from a techno-economic analysis TEA show economy of scale for CBBs by modularization and reveal the binder as the cost driver for material costs. Ideally, the incorporation of post-consumer recycled thermoplastic will decrease material acquisition costs and increase product sustainability. Notably, CBBs do not require the high temperature calcination needed to produce cement, nor do they require firing in the 1600-2400 °F range for three days using natural gas, as do clay brick equivalents. Instead, CBBs are heated to a modest <600 °F according to the melt flow index of the thermoplastic binder. Existing anthracite mines can be expanded to produce CBBs to reduce aggregate transportation costs and emissions that exist for clay bricks. TEA reflects this reduced energy cost while a comparative CO2 emission analysis quantifies the reduced environmental footprint. The market survey identifies several commercialization opportunities, dependent upon the brick classification.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Mesoscale simulations of pressure-shear loading of granular tungsten carbide

Numerical simulations of pressure-shear loading of a granular material are performed using the shock physics code CTH. A simple mesoscale model for the granular material is used that consists of a randomly packed arrangement of solid circular or spherical grains of uniform size separated by vacuum. The grain material is described by a simple shock equation of state, elastic perfectly plastic strength model, and fracture model with baseline parameters for WC taken from previous mesoscale modeling work. Simulations using the baseline material parameters are performed at the same initial conditions of pressure-shear experiments on dry WC powders. Except for some localized flow regions appearing in simulations with an approximate treatment of sliding interfaces among grains, the samples respond elastically during shear, which is in contrast to experimental observations. By extending the simulations to higher shear wave amplitudes, macroscopic shear failure of the simulated samples is observed with the shear strength increasing with increasing stress confinement. The shear strength is also found to be strongly dependent on the grain interface treatment and on the fracture stress of the grains, though the variation in shear strength due to fracture stress decreases with increasing stress confinement. At partial compactions, the transverse velocity histories show strain-hardening behavior followed by formation of a shear interface that extends through the transverse dimensions of the sample. Near full compaction, no strain hardening is observed and, instead, the sample transitions sharply from an elastic response to formation of an internal shear interface. Agreement with experiment is shown to worsen with increasing confinement stress with simulations overpredicting the shear strengths measured in experiment. The source of the disagreement can be ultimately attributed to the Eulerian nature of the simulations, which do not treat contact and fracture realistically.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Eco-Friendly High-Performance Carbon Building Material Development from Coal

The development of eco-friendly high-performance building materials based on coal-derived materials is greatly beneficial for promoting environmental sustainability and the coal industry. This project focused on advancing technology to create innovative and scalable construction materials from two domestic sources: (1) coal-derived pyrolyzed char (PC), and (2) solvent-extracted coal deposit, extracts, and residue (CDER). It aimed to simultaneously develop and produce two types of coal-derived building products: (1) char-based concrete bricks (CCB) for wall construction in buildings, and (2) carbon-based structural units (CSU) intended as alternatives to traditional wood, concrete, or steel framing structures. The project team has successfully developed methods for manufacturing CCB samples. Extensive experiments were conducted to assess various manufacturing techniques for these samples. This included measuring their physical properties such as thermal conductivity (ranging from 0.26 to 0.38 W/mK) and bulk density (ranging from 0.85 to 1.15 g/cm 3 ), along with their mechanical properties (e.g., compressive strength ranging from 14 to 16 MPa at 28 days) for samples with a PC composition of 70%. Quality assurance and quality control tests, focusing on density and compressive strength, were also performed on samples selected randomly from pilot-scale production, and cured for a long term (over three months). The average long-term compressive strength of two randomly selected CCB samples was measured as 15.1 MPa, which was higher than the required target strength of 14 MPa. This indicates that the manufactured CCB samples from the preliminary pilot scale production run have good quality control and long-term strength performance.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Developing Methods to Assess Changes in Mechanical Properties of Shale Modified by Engineered Mineral Precipitation

Fractures in subsurface shale formations serve multiple purposes, for example, in the recovery of resources in hydraulic fracturing or as potential harmful leakage passages through caprocks that may contribute undesired fluids to the atmosphere or functional groundwater aquifers. A proposed method to seal or influence fracture properties is Ureolysis-Induced Calcium Carbonate Precipitation (UICP), a bio-mineralization technology driven by the enzymatic hydrolysis of urea, resulting in the formation of calcium carbonate. Sporosarcina pasteurii is a common microbe used as the source of the urease enzyme that catalyzes the chemical reaction. The resulting calcium carbonate can bridge the gaps in fractured shale and reduce fluid flow through fractures. However, there is little information on how this process affects the mechanical properties of the resulting biomineralized shale. This study represents the first step toward determining the influence of UICP treatment on shale material and its subsequent mechanical strength properties. This methods development study aims to determine the effect that temperature has on the tensile strength of intact, unfractured shale cores (2.54 cm (1 in) diameter, 5.08 cm (2 in) long). Tensile strength was determined indirectly using a modified Brazilian test where the splitting tensile strength is attained by applying a compressive load onto the core. Shale cores from Eagle Ford and Wolfcamp formations were tested at both room temperature and 60°C to determine if increased temperature influences the tensile strength of the rock. This data will help to assess the necessity of testing biomineralized cores at temperature. Though 60°C may not mimic subsurface temperatures of the shales used in this study, it was chosen due to limitations of the UICP process while still approaching temperatures of shale formations. This project aims to evaluate what effect temperature has on the mechanical properties of intact shale cores so that engineered or natural rock fractures that are sealed by biomineralization can be better understood.

Bedey, Kayla↗
DOE OSTI2024

Complete Optimization of LPBF Ni-Based Alloys Down-Selected from FY23 Candidate Materials Including, Thermodynamic Modeling, Sample Fabrication and Microstructure Characterization

The goal of the Advanced Materials and Manufacturing Technologies (AMMT) program is to accelerate the incorporation of new materials and manufacturing technologies into advanced nuclear-related systems. Although 316H stainless steel fabricated by laser powder bed fusion (LPBF) has already been identified as an alloy that could have a significant effect on various reactor technologies, many other materials and manufacturing techniques are being evaluated. Nickel-based alloys typically offer higher-temperature capabilities compared with advanced stainless steels, and previous reports looked at three Ni-based alloy categories: low-Co alloys with a potential use close to the reactor core; high-temperature, high-strength alloys; and molten salt–compatible alloys. In the first category, alloy 718 was studied in 2023, and creep testing at 600°C and 650°C revealed that the alloy exhibited great creep strength after the appropriate annealing but had low ductility. Advanced characterization was recently conducted to highlight the presence of strengthening γ' and γ" precipitates after creep testing and to show that brittle phases at grain boundaries might explain the low ductility of LPBF 718 compared with wrought 718. For the high-temperature, high-strength alloys, previously purchased powders of alloys 617, 230, and 625 were used to assess the printability of these three solution-strengthened alloys. Hot cracking could not be suppressed for alloy 617 and 230, and it was shown that these cracks, which were elongated along the build direction (BD), had a drastic effect on the ductility of alloy 230 at room temperature when specimens were machined perpendicular to the BD. On the contrary, LPBF printing of crack-free alloy 625 was achieved using similar printing parameters, and the alloy looked like a promising candidate for various reactor technologies. The fabrication of alloy 282 by LPBF, a γ'-strengthened alloy with great creep strength up to 800°C, was performed in 2023, and x-ray computed tomography (XCT) scans of the alloy before and after creep testing at 750°C were carried out to assess the effect of flaws on the alloy’s creep behavior. Correlation between the flaws’ volume fraction, creep ductility, and creep lifetime could be established, and future work on LPBF 625 will take full advantage of in situ printing data and ex situ XCT scans to accelerate the alloy qualification. Finally, single track experiments were performed on the two alloys previously identified as good molten salt–resistant, Ni-based candidates: Hastelloy N and 244. Various laser parameters were considered, and cracking was not observed for either of the two alloys. Wrought 244 offers better creep strength and molten salt compatibility than alloy 625, and future work will aim to establish the alloy LPBF processing window.

36 MATERIALS SCIENCE↗
DOE OSTI2025

ULTIMATE Phase I project: Development of Niobium-based alloys for Turbine Applications

Current Ni-based alloys used in turbine blade applications are operating at 1100°C which is approximately 90% of the solidus of Ni-based alloys. Further increases in temperature can be achieved only through the use of alloys with higher solidus temperatures such as refractory alloys which include Mo, Nb, W, Ta alloys. Niobium has a unique combination of physical properties that include a high melting point (2468°C), lowest density (8.57 g/cc), and the lowest modulus amongst refractory alloys, a good thermal conductivity that increases from 45 W/mK at room temperature to 62 W/mK at 1093°C, good ductility with fabricability using traditional techniques, high strength, good creep resistance, and general chemical inactivity. Hence niobium alloys offer many advantages for use at the desired temperature of 1300°C. One of the major deterrents to the use of niobium and its alloys at high temperatures is achieving good oxidation resistance. In addition, achieving balanced properties of room temperature strength, ductility, fracture toughness, high temperature strength, and creep resistance required for 1300°C operation at a density of 9 g/cm 3 is extremely challenging since the addition of W which is a potent strengthener increases the density of the alloy. This project seeks to enable the development of a tri-layered turbine blade that can operate continuously at 1300°C with the core of the turbine blade providing good creep resistance, the second layer providing improved oxidation resistance over the core layer, and the third layer being an environmental barrier providing oxidation resistance. The objective of this Phase 1 project was to use computational modeling and advanced characterization tools to develop two classes of Nb alloys which could be used as the core layer and the transition layer. The first class of alloys developed in this project was a Nb-alloy designed to serve as the turbine blade core with excellent room temperature strength, ductility, and high temperature strength and creep resistance required for 1300°C operation. These alloys were designed to contain sufficient solute solution strengthening elements (W, Mo) but constrained by the density of alloy, along with the addition of elements such as Zr, Hf, Ta, C, and N to achieve a combination of primary and secondary carbide precipitation. A total of 38 “creep-resistant” alloys were designed and cast during the duration of the project. Processing techniques were developed to keep the oxygen contents as low as possible with typical oxygen contents less than 250 ppm. One alloy with a density of < 9.5 g/cc was successful in meeting the Phase 2 intermediate project mechanical property milestone requirements of room temperature ductility greater than 1.0%, 1200°C creep strain of less than 3% at 150 MPa and 100 hours in vacuum, and with solidus temperature greater than 1500ᵒC. The second class of alloys was designed to be a Nb-rich alloy with improved oxidation resistance when compared to the core layer and was designed specifically to be compatible with the core layer and the outer environmental barrier coating. This Nb- alloy will be specifically designed to be microstructurally stable at these temperatures when in contact with the core alloy and provide protection against catastrophic failure of the barrier coating. Two alloys were cast and processed but further development was discontinued to focus on the development of the creep resistant alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical Behavior of Al–Al2Cu–Si and Al–Al2Cu Eutectic Alloys

In this study, laser rapid solidification technique was used to refine the microstructure of ternary Al–Cu–Si and binary Al–Cu eutectic alloys to nanoscales. Micropillar compression testing was performed to measure the stress–strain response of the samples with characteristic microstructure in the melt pool regions. The laser-remelted Al–Al2Cu–Si ternary alloy was observed to reach the compressive strength of 1.59 GPa before failure at a strain of 28.5%, which is significantly better than the as-cast alloy with a maximum strength of 0.48 GPa at a failure strain of 4.8%. The laser-remelted Al–Cu binary alloy was observed to reach the compressive strength of 2.07 GPa before failure at a strain of 26.5%, which is significantly better than the as-cast alloy with maximum strength of 0.74 GPa at a failure strain of 3.3%. The enhanced compressive strength and improved compressive plasticity were interpreted in terms of microstructural refinement and hierarchical eutectic morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical Behavior Assessment of Ti-6Al-4V ELI Alloy Produced by Laser Powder Bed Fusion

The present work correlates the quasi-static, tensile mechanical properties of additively manufactured Ti-6Al-4V extra low interstitial (ELI, Grade 23) alloy to the phase constituents, microstructure, and fracture surface characteristics that changed with post-heat treatment of stress relief (670 °C for 5 h) and hot isostatic pressing (HIP with 100 MPa at 920 °C for 2 h under an Ar atmosphere). Ti-6Al-4V ELI alloy tensile specimens in both the horizontal (i.e., X and Y) and vertical (Z) directions were produced by the laser powder bed fusion (LPBF) technique. Higher yield strength (1141 MPa), higher tensile strength (1190 MPa), but lower elongation at fracture (6.9%), along with mechanical anisotropy were observed for as-stress-relieved (ASR) samples. However, after HIP, consistent and isotropic mechanical behaviors were observed with a slight reduction in yield strength (928 MPa) and tensile strength (1003 MPa), but with a significant improvement in elongation at fracture (16.1%). Phase constituents of acicular α' phase in ASR and lamellar α + β phases in HIP samples were observed and quantified to corroborate the reduction in strength and increase in ductility. The anisotropic variation in elongation at fracture observed for the ASR samples, particularly built in the build (Z) direction, was related to the presence of “keyhole” porosity.

42 ENGINEERING↗
DOE OSTI2022

Evaluation of High-Temperature Martensitic Steels for Heavy-Duty Diesel Piston Applications

Five different commercially available high-temperature martensitic steels were evaluated for use in a heavy-duty diesel engine piston application and compared to existing piston alloys 4140 and microalloyed steel 38MnSiVS5 (MAS). Finite element analyses (FEA) were performed to predict the temperature and stress distributions for severe engine operating conditions of interest, and thus aid in the selection of the candidate steels. Complementary material testing was conducted to evaluate the properties relevant to the material performance in a piston. The elevated temperature strength, strength evolution during thermal aging, and thermal property data were used as inputs into the FEA piston models. Additionally, the long-term oxidation performance was assessed relative to the predicted maximum operating temperature for each material using coupon samples in a controlled-atmosphere cyclic-oxidation test rig. A current commercial steel piston alloy, quenched and tempered martensitic steel 4140, was tested in a single-cylinder research engine for a baseline oxidation and mechanical performance assessment using an abbreviated (50h) durability test plan. The predicted suitability of a candidate piston material in an engine is primarily based on its elevated temperature strength, oxidation resistance, and the complex influence of thermal conductivity, the latter of which is substantially lower for the candidate materials considered in this research relative to the traditional alloys. Although the lower thermal conductivity causes the candidate alloys to operate in higher temperature ranges under identical engine operating conditions and piston geometries, increasing the likelihood of partially or completely negating their strength and oxidation resistance advantages relative to 4140 and MAS steels, this evaluation indicates that several of the candidate piston alloys are predicted to enable improved oxidation resistance under more severe engine operating conditions relative to the current piston materials. However, further evaluation is required to determine if the elevated temperature fatigue strength and durability of these alloys are suitable for more severe engine conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Progressive collapse analysis of stiffened panel structure with consideration of actual welding distortion and residual stresses

To date, inclusion of welding distortion and residual stresses in determining the strength of marine structures is based on empirical formulations due to welding complexity. In this study, a more feasible numerical model was developed from the perspective of inherent strain theory. The accuracy of this simplified numerical model was confirmed by transient thermo-elastic–plastic finite element analysis using a novel dynamic mesh refining and iterative substructure method which is 50 times faster than conventional finite element method. Welding distortion by the two numerical approaches was validated with experimental measurement. The collapse analyses indicated that the inherent strain model predicted a compressive strength and load-displacement curve with high accuracy, as validated by the transient thermo-mechanical model. The global stiffness and the ultimate strength of the welded structure would be overestimated by about 22% if no welding effects were considered. The proposed computation procedure for determining the ultimate strength of welded structures is accurate, simple, and practical and enables improvement of ultimate strength through optimization of welding joint design to reduce the welding residual stress and distortion.

Huang, Hui↗
DOE OSTI2022

SIW21-95: Hybridizing Synchronous Condensers with Grid-Forming Battery Energy Storage Systems

One of the main challenges associated with deployment of high shares of inverter-based resources (IBRs) in power grid is not only reduced system inertia but also degrading system strength that may cause severe stability impacts. A minimum level of system strength is needed for the power system to remain stable under normal conditions and to return to a steady state condition following a system disturbance. Significant system strength reduction is expected in almost all planned areas for solar and wind generation deployment. Synchronous condensers (SC) have been considered as one main technology to address the system strength issues for the areas with high levels of IBRs. SCs can help improving reliability and resiliency of power system but they do not provide the full range of services needed by power systems for reliable and economic integration of high shares of inverter-coupled variable generation such as PV generation. Services related to active power controls cannot be provided by SCs due to lack of prime mover. Even for provision of reactive power SCs have certain constraints based on their thermal and stability limits. NREL has been conducting research on a hybridized concept that combines SCs with grid forming (GFM) battery energy storage systems (BESS). This super flexible AC transmission system (SuperFACTS) that combines these two technologies in a single plant under the same controller offers a unique scalable set of services to the power system at all levels (transmission, sub-transmission, distribution, islands and isolated microgrids). Depending on use cases, SuperFACTS can be controlled to provide fully dispatchable and flexible operation using energy storage component, provide a full range of existing and future ancillary and reliability services to the grid (similar or better than conventional sources), maintain adequate levels of grid strength and inertia, and provide fault current for proper operation of protection systems. Therefore, this economic and easy to commercialize solution has potential for significant impacts on certain segments of global energy sector. All types of gird services (market based, reliability and resiliency) can be provided by SuperFACTS plants. GFM BESS can act as a self-black start source for each SuperFACTS module, which in turn can act a black start resource for co-located PV and wind power plants, segments of transmission and distribution networks, for conventional power plants, etc. The issue of in-rush currents during black start is addressed by overcurrent capability of SCs. In this paper we describe the results of modeling for SuperFACTS concept.

grid forming↗
DOE OSTI2022

Extracting single fiber transverse and shear moduli from off-axis misalignment fiber tensile testing

Small diameter (<100 μm) fibers (e.g. carbon fibers, Kevlar, and fiberglass) and wires (e.g. ultrafine copper and aluminum wires) are frequently used in many different engineering applications, such as for light weighting structures, electromagnetic shielding for aircraft/infrastructure/EVs, vibration damping, biological sensors, aerospace electrical devices, and electric windings just to name a few. Due to the manufacturing process, the fibers and wires are pulled and stretched to produce a preferential alignment. Therefore, thin fibers and wires typically display different properties along the length of the fiber as opposed to their cross section and many fibers/wires are considered transversely isotropic. The axial properties of fibers/wires can be ascertained via tensile testing of single-filaments or fiber tows, but the radial properties require much more effort to measure. Knowing these properties is important for the accurate prediction of micromechanical models and manipulation of fibers during micromanufacturing. In this paper, a new technique was developed to determine the transverse/shear moduli and strength of a material by conducting tensile tests of the material at increasing misalignment angles from the tensile axis. Due to the transversely isotropic nature of the material, the transverse/shear moduli and strength influence the experimental results recorded by the test machine to different degrees based on the amount of misalignment in the test setup. An equation was derived to determine the influence of each of the material properties based on the misalignment angle by manipulating the stiffness matrix for transversely isotropic materials using the transformation matrices. Then, curve fitted coefficients were used to identify the material properties. Here, the strengths were similarly determined by curve fitting an off-axis Tsai-Hill failure criteria to determine the influence of transverse, shear, and tensile strengths based on the complex loading condition provided by the off-axis tensile test. Zoltek Panex 35 carbon fibers were used to demonstrate this new technique and the determined properties were then compared to those obtained from nanoindentation and from literature. Fracture surfaces provide insight into the different failure mechanisms at various misalignment angles.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Macroscale Fabrication of Lightweight and Strong Porous Carbon Foams through Template-Coating Pair Design

Manufacturing of low-density-high-strength carbon foams can benefit the construction, transportation, and packaging industries. One successful route to lightweight and mechanically strong carbon foams involves pyrolysis of polymeric architectures, which is inevitably accompanied by drastic volumetric shrinkage (usually >98%). As such, a challenge of these materials lies in maintaining bulk dimensions of building struts that span orders of magnitude difference in length scale from centimeters to nanometers. Here, this work demonstrates fabrication of macroscale low-density-high-strength carbon foams that feature exceptional dimensional stability through pyrolysis of robust template-coating pairs. The template serves as the architectural blueprint and contains strength-imparting properties (e.g., high node density and small strut dimensions); it is composed of a low char-yielding porous polystyrene backbone with a high carbonization-onset temperature. The coating serves to imprint and transcribe the template architecture into pyrolytic carbon; it is composed of a high char-yielding conjugated polymer with a relatively low carbonization-onset temperature. The designed carbonization mismatch enables structural inheritance, while the decomposition mismatch affords hollow struts, minimizing density. The carbons synthesized through this new framework exhibit remarkable dimensional stability (≈80% dimension retention; ≈50% volume retention) and some of the highest specific strengths (≈0.13 GPa g -1 cm 3 ) among reported carbon foams derived from porous polymer templates.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of coal-derived carbon-based structural unit as a potential new building material

Coal combustion for energy has not only wasted the hydrogen-rich volatile matters but also results in CO 2 emission causing serious environmental issues. An integrated coal pyrolysis and solvent extraction process under elevated temperatures in an inert atmosphere is implemented to convert as-mined coal from Wyoming Powder River Basin to functional carbon elements such as pyrolysis char (PC). This paper presents the development and fabrication of new carbon-based structural unit (CSU) using pulverized PC and two coal-derived pitches (mesophase pitch and tar pitch) to attain high compressive strength greater than 30 MPa, low thermal conductivity less than 0.30 W/m.K, and low density less than 1.25 g/cm 3 . CSUs have the potential to overcome the current challenges with cement and concrete through pressurized fabrication followed by carbonization. This study aims to develop CSU with nearly 100% coal-derived carbon material for structural application in buildings. The effects of pressing pressures, carbonization temperatures, and binder contents on the density and mechanical and thermal properties of CSU samples are investigated. The study concludes that mesophase pitch produces a better performance of CSU samples, a combination of 100 MPa pressing pressure and carbonization temperature of 900 ⁰C yields the highest compressive strength, and a 25% MP content is recommended for low-cost CSU fabrication. Furthermoer, CSU has a much lower density, lower thermal conductivity, higher compressive strength, and higher strength-to-density ratio than normal concrete.

36 MATERIALS SCIENCE↗