Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “storing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
DOE OSTI2011

Thermochemical Heat Storage for Concentrated Solar Power: Thermochemical System Reactor Design for Thermal Energy Storage

Thermal energy storage (TES) is an integral part of a concentrated solar power (CSP) system. It enables plant operator to generate electricity beyond on sun hours and supply power to the grid to meet peak demand. Current CSP sensible heat storage systems employ molten salts as both the heat transfer fluid and the heat storage media. These systems have an upper operating tempera ture limit of around 400°C. Future TES systems are expected to operate at temperatures between 600°C–1000°C for higher thermal efficiencies which should result in lower electricity cost. To meet future operating temperature and electricity cost requirements, a TES concept utilizing thermochemical cycles (TCs) based on multivalent solid oxides was proposed. The system employs a pair of reduction and oxidation (REDOX) reactions to store and release heat. In the storage step, hot air from the solar receiver is used to reduce the oxidation state of an oxide cation, e.g. Fe 3+ to Fe 2+ . Heat energy is thus stored as chemical bonds and the oxide is “charged”. To discharge the stored energy, the reduced oxide is re-oxidized in air and heat is released. Air is used as both the heat transfer fluid and reactant and no storage of fluid is needed. This project investigated the engineering and economic feasibility of this proposed TES concept. The DOE storage cost and LCOE targets are $\$$15/kWh and $\$$0.09/kWh respectively. Sixteen pure oxides cycles were identified through thermodynamics calculations and literature information. Data showed the kinetics of re-oxidation of the various oxides to be a key barrier to implementing the proposed concept. A down selection was carried out based on operating temperature, materials costs and preliminary laboratory measurements. Cobalt oxide, manganese oxide and barium oxide were selected for developmental studies to improve their REDOX reaction kinetics. A novel approach utilizing mixed oxides to improve the REDOX kinetics of the selected oxides was proposed. It partially replaces some of the primary oxide cations with selected secondary cations. This causes a lattice charge imbalance and increases the anion vacancy density. Such vacancies enhance the ionic mass transport and lead to faster re-oxidation. Re oxidation fraction of Mn 3 O 4 → Mn 2 O 3 and CoO → Co 3 O 4 was improved by up to 16 fold through the addition of a secondary oxide. However, no improvement was obtained in barium based mixed oxides. In addition to enhancing the short term re-oxidation kinetics, it was found that the use of mixed oxides also help to stabilize or even improve the TES properties after long term thermal cycling. Part of this improvement could be attributed to a reduced grain size in the mixed oxides. Based on the measurement results, manganese-iron, cobalt-aluminum and cobalt iron mixed oxides have been proposed for future engineering scale demonstration. Using the cobalt and manganese mixed oxides, we were able to demonstrate charge and discharge of the TES media in both a bench top fixed bed and a rotary kiln-moving bed reactor.

14 SOLAR ENERGY↗
NASA NTRS2018

Hosting Hyrax in the Cloud While Preserving the User Experience

Cloud object stores enable data providers to reduce costs and provide uniform data servers across organizational divisions. This talk will address how new capabilities provided by cloud computing can be used with existing software so that users get the benefits provided by cloud technology (access to data at lower cost, e.g.) without disrupting their existing workflow(s). We will address ways to reduce response latency often associated with Cloud object stores and ways to simulate the hierarchy of a POSIX file system using a key-value object store. This work is based an on-going NASA EED2 project to enhance the Hyrax data server for operation in the Amazon Web Services Cloud.

Hyrax server↗
DOE OSTI2016

Evaluating the long-term hydrology of an evapotranspiration-capillary barrier with a 1000 year design life

A surface barrier (or cover) is a commonly used technology for subsurface remediation. A key function of the barrier is to reduce or eliminate the movement of meteoric precipitation into the underlying waste zone, where it could mobilize and transport contaminants. Surface barriers are expected to perform for centuries to millennia, yet there are very few examples of performance for periods longer than a decade. The Prototype Hanford Barrier was constructed in 1994 over an existing waste site to demonstrate its long-term performance for a design period of 1000 years. This barrier is a field-scale evapotranspiration-capillary (ETC) barrier. In this design, the storage layer consists of 2-m-thick silt loam. The 19-year monitoring results show that the store-and-release mechanism for the ETC barrier worked efficiently as the storage layer was recharged in the winter season (November to March) and the stored water was released to the atmosphere in the summer season (April to October) via soil evaporation and plant transpiration. The capillary break functioned normally in improving the storage capacity and minimizing drainage. The maximum drainage observed through the ET barrier at any of the monitoring stations was only 0.178 mm yr -1 (under an enhanced precipitation condition), which is less than the design criterion. A very small amount (2.0 mm yr -1 on average) of runoff was observed during the 19-year monitoring period. The observed storage capacity of the storage layer was considerably (39%) larger than the estimated value based on the method of equilibrium of water pressure. After a controlled fire in 2008, the newly grown vegetation (primarily shallow-rooted grasses) could still release the stored water and summer precipitation to the atmosphere via transpiration. The findings are useful for predicting water storage and ET under different precipitation conditions and for the design of future barriers.

58 GEOSCIENCES↗
DOE OSTI2022

Simulation study of chemo-mechanical impacts of CO 2 injection in morrow b sandstone reservoir

Here, this study investigates the impacts of geomechanical and geochemical changes on carbon storage in a partially depleted oil reservoir, using results from four different coupled simulation models. Models were used to examine the relative importance of storage mechanisms, and how changing reservoir parameters might affect these mechanisms through time. The study uses data from a Morrowan sandstone reservoir in the Farnsworth Unit (FWU), Ochiltree County, Texas which is currently undergoing CO 2 enhanced oil recovery (EOR). Partially depleted oil reservoirs such as the FWU offer attractive carbon utilization and/or storage targets because of existing infrastructure and economic benefits from incremental oil recovery as well as tax credits. However, prediction of storage capacity or long-term fluid migration in these fields can be difficult because of the wide variation in formation fluids and operational histories that may have undergone. CO 2 injection can cause complex geomechanical and geochemical responses in a reservoir as a result of interplay between dynamic changes in pore pressure, reservoir temperature, fluid composition, and interactions between formation fluids, CO 2 , and reservoir rock. Thus, multiple coupled numerical simulation models must be developed and used to more precisely understand what CO 2 storage mechanisms are most significant, as well as the long-term fate of the stored CO 2 . Our study used results from hydrodynamic, coupled hydro-geomechanical, coupled hydro-geochemical, and coupled hydro-geomechanical-geochemical models to examine how changes in geomechanical and geochemical properties can impact the injectivity or storage capacity of CO 2 . Models simulated historical field operations and then forward-modeled a water-alternate-gas (WAG) operation for 20 years, followed by a 1000-year post-injection monitoring. The work demonstrates that in this specific reservoir, geomechanical impacts appear to be more significant than any geochemical processes, which showed minimal impact on reservoir properties. Furthermore, these simulation scenarios corroborated other studies showing more than 90% of CO 2 injected are being stored and will remain stored in the reservoir. The study was able to draw on a rich set of data from this currently operational project for the work. Because the Morrow is a widespread oil-bearing reservoir in the midcontinent of the United States and is fairly typical of many sandstone reservoirs elsewhere, the study has significance beyond the boundaries of our field area.

58 GEOSCIENCES↗
DOE OSTI2025

Carbon Storage in Fold‐and‐Thrust Belts: An Overlooked Gigatonne Storage Opportunity

This study presents numerical investigations of the trapping characteristics of fold-and-thrust belt structures, defining three carbon capture and storage (CCS) play types that could be used to store commercial volumes (millions of tonnes) of CO 2 . Specifically, we present simulations of CO 2 storage in three fold-and-thrust belt models comprising a thrust-ramp, duplex, and thrust-fold geometry. To constrain these play types in realistic geology, each model is based on a study site, including a novel investigation of a greenfield saline reservoir in Virginia, USA, being considered for commercial carbon storage and two well-characterized petroleum fields: the Wilburton field in Oklahoma, USA, and the Incahuasi field in Bolivia. Our results provide insight into several key parameters, such as the long-term security of injected CO 2 in these geologies and injection strategies for maximizing storage efficiency while reducing pressure-related risk. These results improve the understanding of CCS in fold-and-thrust belt storage sites globally by describing general storage parameters that may be applied to site-specific projects. We find that thrust-ramp geometries may securely trap CO 2 through solubility and hydrodynamic trapping under suitable reservoir conditions, duplex structures may store some quantities of CO 2 but are pressure-constrained, and that thrust-ramp structures may store large quantities of CO 2 by maximizing fetch volume, which simultaneously lowers geomechanical risk by reducing pressure buildup along zones of weakness.

42 ENGINEERING↗
DOE OSTI2022

Climatic controls on soil and saprock nitrogen distribution and persistence in the Sierra Nevada

Nitrogen (N) is an essential nutrient in soil that regulates plant growth, terrestrial sequestration of atmospheric carbon dioxide, and persistence of organic compounds. However, major knowledge gaps remain about how climate change may impact N accumulation and persistence, especially in deep soil and saprock (friable weakly weathered bedrock). Our objective was to understand how climate impacts the accumulation of N in soil and saprock and how climate impacts soil N distribution, persistence, and mechanisms of N persistence. We investigated N concentration in bulk soil and density fractions. We estimated N persistence along a bio-climatic sequence—sites range from a low-elevation oak savannah, mid-elevation pine-oak/mixed-conifer forest, to a high-elevation subalpine forest—in the southern Sierra Nevada in California. A combination of radiocarbon and elemental composition measurements along with a first-order kinetic model was used. The N concentration in the bulk soil and density fractions declined with depth, and there was a relatively greater mineral-associated heavy fraction (HF) N in deeper samples. The cooler/wetter mixed conifer site held 37% of profile N in saprock, which was greater than that of the entire soil profile at the drier/hotter oak savannah. The majority of N in soil, which was in the HF, was not influenced by climate proxies tested. However, both unprotected and occluded fractions of N were strongly influenced by climate. Soil N mean residence time (MRT) showed that drier/hotter climates have a shorter MRT, compared to mid-elevation sites with cooler/wetter climates. The effect of climate on deep saprock N storage might be indirect, primarily through climatic influence on the thickness of saprock. Overall, our findings suggest the mineral-associated HF N pool will not be vulnerable to changes in climate and will continue to contribute to the persistent soil N pool. The amount of topsoil and subsoil unprotected and occluded N can be explained by gross primary productivity and mean annual precipitation indicating that changes in climate can influence N partitioning. N stored in deep soil and saprock may be less vulnerable to climate than N stored in drier/hotter climates with less deeply stored N. It is critical to dig deeper to understand terrestrial ecosystems’ response to climate.

58 GEOSCIENCES↗
DOE OSTI2024

Effects of moisture and aging upon decomposition of methyl iodide by reduced silver mordenite

Abstract Reduced silver mordenite has been considered as a sorbent for the capture of organic iodides, especially methyl iodide, from off-gases produced by aqueous used nuclear fuel reprocessing operations. The adsorption capacity of this material has been unpredictable especially when NO x and water are present. Previous work has found that a catalytic decomposition reaction is occurring on the surface but few determinations have been made of the kinetics of this reaction. The work presented tested the adsorption behavior and apparent catalytic reaction rate in humid conditions and compared those to dry conditions testing. Both experiments observed a first order reaction with rate constants of 0.0847 L/g sorbent/s and 0.1202 L/g sorbent/s respectively. Such a reduction in apparent rate constant is possibly due to either water obstructing methyl iodide adsorption or product desorption limitation. Changes in the adsorption profile were also apparent between these two, with the humid conditions experiment reaching saturation sooner than the dry conditions experiment. Additionally, an experiment into the effects of sorbent storage in a controlled laboratory environment was performed. The performance of the sorbent materials that were stored with silver in the zerovalent state was slightly inferior to those materials that were stored in ionic form (Ag + ) and reduced to zerovalent silver immediately prior to subjecting them to sorption test. The materials stored with silver in the ionic form (and reduced just prior to application) behaved essentially similarly to the freshly synthesized (and reduced) sorbents in the sorption tests. This suggests that zerovalent silver experiences some oxidation resulting in deactivation of some sites.

Goettsche, Heinrik↗
DOE OSTI2021

Nitrogen and phosphorus cycling in an ombrotrophic peatland: a benchmark for assessing change

Aims Slow decomposition and isolation from groundwater mean that ombrotrophic peatlands store a large amount of soil carbon (C) but have low availability of nitrogen (N) and phosphorus (P). To better understand the role these limiting nutrients play in determining the C balance of peatland ecosystems, we compile comprehensive N and P budgets for a forested bog in northern Minnesota, USA. Methods N and P within plants, soils, and water are quantified based on field measurements. The resulting empirical dataset are then compared to modern-day, site-level simulations from the peatland land surface version of the Energy Exascale Earth System Model (ELM-SPRUCE).

Salmon, Verity G.↗
DOE OSTI2022

Pumped Thermal Energy Storage With Liquid Storage

Pumped Thermal Energy Storage (PTES) uses electricity to power a heat pump; transferring heat from a cold space to a hot space forms a hot and a cold thermal reservoir, thereby storing energy. To discharge, the temperature difference between the two stores is used to drive a heat engine which generates electricity. In this chapter, PTES systems which store energy in liquids will be described. The chapter will concentrate on Joule-Brayton power cycles with molten salt storage. Part-load operation of Joule-Brayton PTES with liquid storage can be managed with "inventory control," and it is demonstrated that this control method leads to relatively good performance over a range of operating points.

Carnot batteries↗
DOE OSTI2017

Evaluation of a high-moisture stabilization strategy for harvested microalgae blended with herbaceous biomass: Part I—Storage performance

Here, algal biomass is becoming increasingly attractive as a feedstock for biofuel production. However, the swing in algal biomass production between summer and winter months poses a challenge for delivering predictable, constant feedstock supply to a conversion facility. Drying is one approach for stabilizing algal biomass produced in excess during high productivity summer months for utilization during low productivity months, yet drying is energy intensive and thus costly. Wet, anaerobic storage, or ensiling, is a low-cost approach that is commonly used to preserve high moisture herbaceous feedstock. The potential for microalgae stabilization without the need for drying was investigated in this study by simulating ensiling, in which oxygen limitation drives anaerobic fermentation of soluble sugars to organic acids, dropping the pH and thereby stabilizing the material. Algal biomass, Scenedesmus obliquus , was blended with corn stover and stored in acidic, anaerobic conditions at 60% moisture (wet basis) to simulate wet storage by means of ensiling. Results demonstrate that algae and corn stover blends were successfully preserved in anaerobic, acidic conditions for 30 days with < 2% dry matter loss occurring during storage compared to 21% loss in aerobic, non-acidified conditions. Likewise, Scenedesmus obliquus stored alone at 80% moisture (wet basis) in acidified, anaerobic conditions for 30 days, resulted in dry matter losses of 6–14%, compared to 44% loss in neutral pH, anaerobic storage and 37% loss in a neutral pH, aerobically stored condition. Additional experiments were performed at a larger scale in which an algae and corn stover blend was subject to mechanical oxygen exclusion and a Lactobacillus acidophilus inoculum, resulting in 8% loss over 35 days and further indicating that acidic, anaerobic conditions can stabilize microalgae biomass. In summary, the stabilization of harvested algae can be achieved through anaerobic storage, securing a feedstock that is labile yet of high value.

09 BIOMASS FUELS↗
DOE OSTI2014

Dynamics of N 2 and N 2 O peaks during and after the regeneration of lean NO x trap

We study the dynamics and selectivity of N 2 and N 2 O formation during and after the regeneration of a commercial NO x storage catalyst containing Pt, Pd, Rh, Ba on Ce/Zr, Mg/Al and Al oxides was studied with high-speed FTIR and SpaciMS analyzers. The lean/rich cycling experiments (60 s/5 s and 60 s/3 s) were performed in the temperature range 200–400°C, using H 2 , CO, and C 3 H 6 individually for the reduction of adsorbed NO x . Isotopically labeled 15 NO was employed in combination with Ar carrier gas in order to quantify the N 2 product by mass spectrometry. N 2 and N 2 O products were formed concurrently. The primary peaks appeared immediately after the rich-phase inception, and tailed off with breakthrough of the reductant front (accompanied by NH 3 product). Secondary N 2 and N 2 O peaks appeared at the rich-to-lean transition as a result of reactions between surface-deposited reductants/intermediates (CO, HC, NH 3 , -NCO) and residual stored NO x . At 200–300 °C, up to 30% of N 2 and 50% of N 2 O products originated from the secondary peaks. The N 2 O/N 2 selectivity ratio as well as the magnitude of secondary peaks decreased with temperature and duration of the rich phase. Among the three reductants, propene generated secondary N 2 peak up to the highest temperature. Lastly the primary N 2 peak exhibited a broadened shoulder aligned with movement of reduction front from the zone where both NO x and oxygen were stored to the NO x -free zone where only oxygen storage capacity was saturated. N 2 formed in the NO x -free zone originated from reaction of NH 3 with stored oxygen, while N 2 O formation in this zone was very low.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Underground hydrogen storage resource assessment for the Cook Inlet, Alaska

Underground hydrogen storage will be essential to a hydrogen economy. This work focuses on the challenge of identifying and screening candidate storage systems, given the unique behavior of hydrogen in the subsurface. Here, we describe a resource assessment methodology and apply it to Alaska’s Cook Inlet region. Alaska provides an interesting case study because of its abundant renewable energy resources, relatively low energy demand, and isolated electrical grid. The assessment framework considers each site’s ability to (1) store a specific volume, (2) physically-contain the stored gas, and (3) limit biogeochemical activity. We estimate that reservoirs in the Cook Inlet area could theoretically store a total of 286 TWh (or 8.6 million tonnes [Mt]) in hydrogen working gas in 92 pools. This is likely sufficient to meet both local hydrogen demand and support an array of exportable products. We further identify seven pools that may be especially well-suited for hydrogen storage. Broadly, this work demonstrates a framework for regional resource assessments. On a finer scale, this work supports an early demonstration of porous–media hydrogen storage in the United States.

08 HYDROGEN↗
DOE OSTI2025

High-performance data format for scientific data storage and analysis

Here, in this article, we present the High-Performance Output (HiPO) data format developed at Jefferson Laboratory for storing and analyzing data from Nuclear Physics experiments. The format was designed to efficiently store large amounts of experimental data, utilizing modern fast compression algorithms. The purpose of this development was to provide organized data in the output, facilitating access to relevant information within the large data files. The HiPO data format has features that are suited for storing raw detector data, reconstruction data, and the final physics analysis data efficiently, eliminating the need to do data conversions through the lifecycle of experimental data. The HiPO data format is implemented in C++ and JAVA, and provides bindings to FORTRAN, Python, and Julia, providing users with the choice of data analysis frameworks to use. In this paper, we will present the general design and functionalities of the HiPO library and compare the performance of the library with more established data formats used in data analysis in High Energy and Nuclear Physics (such as ROOT and Parquete). In columnar data analysis, HiPO surpasses established data formats in performance and can be effectively applied to data analysis in other scientific fields.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2011

A quantitative comparison of the cost of employing EOR-coupled CSS supplemented with secondary DSF storage for two large CO2 point sources

This paper explores the impact of the temporally dynamic demand for CO2 for enhanced hydrocarbon recovery with CO2 storage. Previous evaluations of economy-wide CO2 capture and geologic storage (CCS) deployment have typically applied a simplifying assumption that 100% of the potential storage capacity for a given formation is available on the first day of the analysis, and that the injection rate impacts only the number of wells required to inject a given volume of fluid per year, making it a cost driver rather than a technical one. However, as discussed by Dahowski and Bachu [1], storing CO2 in a field undergoing CO2 flooding for enhanced oil recovery (EOR) is subject to a set of constraints to which storage in DSFs is not, and these constraints combined with variable demand for CO2 may strongly influence the ability of an EOR field to serve as a baseload storage formation for commercial scale CCS projects undertaken as a means of addressing climate change mitigation targets. This analysis assumes that CCS is being undertaken in order to reduce CO2 emissions from the industrial sources evaluated and that there is enough of a disincentive associated with venting CO2 to the atmosphere that any CO2 not used within the EOR field will be stored in a suitable nearby deep saline formation (DSF). The authors have applied a CO2 demand profile to two cases chosen to illustrate the differences in cost impacts of employing EOR-based CCS as a part of a given source’s CCS portfolio. The first scenario is a less-than-ideal case in which a single EOR field is used for storage and all CO2 not demanded by the EOR project is stored in a DSF; the second scenario is designed to optimize costs by minimizing storage in the DSF and maximizing lower-cost EOR-based storage. Both scenarios are evaluated for two facilities emitting 3 and 6 MtCO2/y, corresponding to a natural gas processing facility and an IGCC electric power plant, respectively. Annual and lifetime average CO2 transport and storage costs are presented, and the impact of added capture and compression costs on overall project economics is examined.

02 PETROLEUM↗
DOE OSTI2018

Performance response of packed-bed thermal storage to cycle duration perturbations

Packed-bed thermal stores are integral components in numerous bulk electricity storage systems and may also be integrated into renewable generation and process heat systems. In such applications, the store may undergo charging and discharging periods of irregular durations. Previous work has typically concentrated on the initial charging cycles, or on steady-state cyclic operation. Understanding the impact of unpredictable charging periods on the storage behavior is necessary to improve design and operation. Here in this paper, the influence of the cycle duration (or 'partial-charge' cycles) on the performance of such thermal stores is investigated. The response to perturbations is explained and provides a framework for understanding the response to realistic load cycles.

14 SOLAR ENERGY↗
DOE OSTI2021

Performance evaluation of a dynamic wall integrated with active insulation and thermal energy storage systems

Thermal energy storage systems in buildings can store cooling/heating energy during non-peak load hours or when renewable energy sources are available for later use when demanded. Using the building envelope as a thermal battery can help to shave the peak load, reduce the burden in electric grids, and enhance the occupant's thermal comfort. Sensible energy storage on wall systems such as thermally activated building systems can provide an active thermal storage strategy. However, most of the stored energy is used through passive means directed by the thermal lag, which can impede the on-demand release of the stored energy. Integrating active insulation systems with building thermal storage systems can increase the flexibility of charging and discharging time and duration. In this study, a wall system equipped with an active insulation system and thermally activated storage system was designed, and its performance on active cooling energy contribution was studied. The performances of energy storage (charging), release (discharging) of the thermal energy storage energy, and the active insulation system were studied separately and together as an integrated system. Results showed that the thermal properties of the thermal energy storage core material and the pipe spacing of both embedded pipes in the thermal energy storage and hydronic pipes used in the active insulation system affected the wall performance the most out of all the tested wall system parameters. During discharging, the heat flux into the wall was as high as 81.92 W/m 2 . This active insulation system's dynamic R-value varied between less than 1ft 2 •°F•h/BTU (0.18 m 2 •K/W) to 98% of the equally thick foam insulation's R-value.

25 ENERGY STORAGE↗
DOE OSTI2019

Flow regimes and storage efficiency of CO 2 injected into depleted shale reservoirs

Depleted shale reservoirs are potentially attractive targets to store carbon dioxide (CO 2 ) as free and adsorbed phases. The time-dependent efficiency factors that depict dynamic storage performance in shale are estimated as a function of key reservoir parameters, shapes of stimulated reservoir volume, and injection scenarios. Efficiency of CO 2 storage and flow regimes are determined dynamically as CO 2 is injected in a depleted shale formation for a time period of 60 years. The most effective reservoir utilization for carbon storage was achieved during the transition from predominant flow in the stimulated reservoir volume to flow into unfractured zones. That transition occurs within first 15–30 years of injection depending on cases considered. The importance of adsorption as a mechanism of storage is determined based on sensitivity, which indicates that the amount of CO 2 stored by adsorption would be on average ~26% of the CO 2 stored as a free phase.

03 NATURAL GAS↗
DOE OSTI2016

Data catalog project—A browsable, searchable, metadata system

Modern experiments are typically conducted by large, extended groups, where researchers rely on other team members to produce much of the data they use. The experiments record very large numbers of measurements that can be difficult for users to find, access and understand. Here. we are developing a system for users to annotate their data products with structured metadata, providing data consumers with a discoverable, browsable data index. Machine understandable metadata captures the underlying semantics of the recorded data, which can then be consumed by both programs, and interactively by users. Collaborators can use these metadata to select and understand recorded measurements. The data catalog project is a data dictionary and index which enables users to record general descriptive metadata, use cases and rendering information as well as providing them a transparent data access mechanism (URI). Users describe their diagnostic including references, text descriptions, units, labels, example data instances, author contact information and data access URIs. The list of possible attribute labels is extensible, but limiting the vocabulary of names increases the utility of the system. The data catalog is focused on the data products and complements process-based systems like the Metadata Ontology Provenance project [Greenwald, 2012; Schissel, 2015]. This system can be coupled with MDSplus to provide a simple platform for data driven display and analysis programs. Sites which use MDSplus can describe tree branches, and if desired create ‘processed data trees’ with homogeneous node structures for measurements. Sites not currently using MDSplus can either use the database to reference local data stores, or construct an MDSplus tree whose leaves reference the local data store. A data catalog system can provide a useful roadmap of data acquired from experiments or simulations making it easier for researchers to find and access important data and understand the meaning of the data and how it was obtained. This is particularly useful in research facilities that study the results of many different experiments or simulations and may not know the intricacies of the data organization in use where the data was generated. It is also possible to store a local copy of key data items in local MDSplus trees and then add processed data to the local catalog.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗