Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shear”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Molecular origin of anisotropic shear elastoplasticity in chitin

Chitin nano- and mesoscale structures present in the exoskeleton of crustaceans exhibit exceptional longitudinal stiffness and toughness, rivaling or even exceeding that of many synthetic polymer architectures. Here, we reveal the origin of the asymmetric shear response in chitin multiscale architectures, marked by pronounced anisotropy in deformation. Under shear aligned with the molecular axis, chitin accommodates strain through coherent atomic rearrangements that enable elastic recovery. In contrast, shear applied perpendicular to this axis induces liquid-like plasticity via localized sliding. These results demonstrate the intrinsic mechanical anisotropy of chitin, underpinning a dual function in resisting repetitive loading while dissipating internal stress during high-strain events. Our findings establish the molecular basis of shear elastoplasticity in multiscale chitin structures, wherein axial elasticity supports energy storage in load-bearing regions, whereas transverse plasticity enables controlled energy dissipation. These atomic-scale insights lay a foundation for the predictive design of chitin-based materials with tunable strength-toughness profiles.

Wan, Zhangmin [University of British Columbia, Van↗

Grain-Boundary Shear-Migration Coupling in Al Bicrystals. Atomistic Modeling

The energy of grain boundary shears is calculated for symmetric grain boundaries (GBs) using ab initio methods and molecular-dynamic modeling in order to elucidate mechanisms that control GB shear-migration coupling in typical symmetric GBs, such as Σ3 (111), Σ5 (012), Σ5 (013) and Σ11 (113) tilt GBs, in Al bicrystal. The energy of generalized grain-boundary stacking faults (GB–SF) is determined, and the preferred directions and the energy barrier are established for grain-boundary slippage. It is shown that the relative slippage of neighboring grains at certain directions of particle shears is accompanied by conservative migration of GB in the direction perpendicular to its plain. The modeling data are comparative to known grain-boundary shear-migration coupling mechanisms in Al.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Prediction of the Shear Failure of Opened Rock Fractures and Implications for Rock Slope Stability Evaluation

Rock slope commonly fails due to the shear failure of rock fractures. Shear strength of rock fractures are reduced substantially once the fracture surfaces are mismatched or opened. We propose a new criterion to predict the shear strength of rock fractures in different opening states. The degree of interlocking representing the true asperity contact area is incorporated into the modified model of Saeb and Amadei. The effect of fracture opening on asperity dilation and degradation is separately considered. The transitional stress that is a critical parameter involved in the model is analytically determined based on energy consideration. The new model is validated with experimental results from direct shear tests on synthetic fractures with regular‐shaped asperities. Good agreement between the analytical solution and the experimental data confirms the capacity of the proposed model. Therefore, the model has great potential for assessing the stability of rock slopes where fractures are often opened due to stress relief and engineering disturbances.

Li, Yingchun (ORCID:0000000201083704)↗

Evolution of Idealized Vortices in Monsoon-Like Shears: Application to Monsoon Depressions

Abstract This study examines processes fundamental to the development of South Asian monsoon depressions using an array of integrations of an idealized convection-permitting numerical model. In each integration, a wave of initially small amplitude is subjected to a different amount of vertical and meridional wind shear, with temperature and moisture fields constructed according to realistic constraints. Based on the evolution of this disturbance into monsoon depression–like vortices, two features of the background environment emerge as important: the low-level gradient of moist static energy (MSE) and the low-level meridional shear. As the low-level MSE gradient steepens, the disturbance becomes stronger and produces more rain. This strengthening results from the interaction of the vortex with latent heat release by convection that is in turn organized by positive MSE advection in the northerly flow west of the vortex. In this region of advection, moister air from the north ascends along upward-sloping isentropes, driving moist convection. The disturbance also becomes stronger with increasing meridional shear, which makes the environment more barotropically unstable. The absence of either of these two features of the background environment prevents substantial growth of the disturbance. Our results suggest that monsoon depression growth in South Asia is fostered by the coexistence of a strong low-level MSE gradient with strong meridional wind shear associated with the monsoon trough.

54 ENVIRONMENTAL SCIENCES↗

Shear Stress in Magnetorheological FInishing for Glasses

We report in situ, simultaneous measurements of both drag and normal forces in magnetorheological finishing (MRF) for what is believed to be the first time, using a spot taking machine (STM) as a test bed to take MRF spots on stationary parts. The measurements are carried out over the entire area where material is being removed, i.e., the projected area of the MRF removal function/spot on the part surface, using a dual force sensor. This approach experimentally addresses the mechanisms governing material removal in MRF for optical glasses in terms of the hydrodynamic pressure and shear stress, applied by the hydrodynamic flow of magnetorheological fluid at the gap between the part surface and the STM wheel. This work demonstrates that the volumetric removal rate shows a positive linear dependence on shear stress. Shear stress exhibits a positive linear dependence on a material figure of merit that depends upon Young’s modulus, fracture toughness, and hardness. A modified Preston’s equation is proposed that better estimates MRF material removal rate for optical glasses by incorporating mechanical properties, shear stress, and velocity.

Miao, C↗

Calculations Using Density Dependent Melt Temperature and Shear Modulus with the PTW Strength Model (U)

This presentation describes one effect of using density dependent melt temperature and shear modulus in calculations with the Preston, Tonks and Wallace (PTW) Strength Model to simulate lab experiments. Calculations are in error if density dependent melt and shear functions are inconsistent with a PTW parameter set for a material. In most laboratory experiments used to determine these strength parameters the density changes are small. So, the melt temperature (T m ) and the shear modulus (G 0 ) are assumed to be constant. However, in order to be consistent with the PTW mode l theory these values should be determined at the laboratory reference density. Two parameters (α and κ) in the model are affected by use of inconsistent values for T m and G 0 . Assuming a correct value of the shear modulus is used in the data fit code has been written to auto-correct inconsistent PTW parameters sets at run time. Furthermore this code will not alter values in consistent parameter set.

36 MATERIALS SCIENCE↗

Cone Penetrometer Shear Strength Measurements of Sludge Waste in Tanks 241-AN-101 and 241-AN-106

This document presents the resulting shear strength profiles for sludge waste in Tanks 241-AN-101 and 241-AN-106, as determined with a full-flow cone penetrometer. Full-flow penetrometer measurements indicate shear strength profiles that increase roughly uniformly with depth. For Tank 241-AN-101, the undrained shear strength was calculated to range from 500 Pa near the sludge surface to roughly 3,300 Pa at 15 inches above the tank bottom. For 241-AN-106, the undrained shear strength was calculated to range from 500 Pa near the sludge surface to roughly 5,000 Pa at 15 inches above the tank bottom.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Multi-Scale Investigation of Sheared Flows In Magnetized Plasmas

Flows parallel and perpendicular to magnetic fields in a plasma are important phenomena in many areas of plasma science research. The presence of these spatially inhomogeneous flows is often associated with the stability of the plasma. In fusion plasmas, these sheared flows can be stabilizing while in space plasmas, these sheared flows can be destabilizing. Because of this, there is broad interest in understanding the coupling between plasma stability and plasma flows. This research project has engaged in a study of the plasma response to spatially inhomogeneous plasma flows using three different experimental devices: the Auburn Linear Experiment for Instability Studies (ALEXIS) and the Compact Toroidal Hybrid (CTH) stellarator devices at Auburn University, and the Space Plasma Simulation Chamber (SPSC) at the Naval Research Laboratory. This work has shown that there is a commonality of the plasma response to sheared flows across a wide range of plasma parameters and magnetic field geometries. The goal of this multi-device, multi-scale project is to understand how sheared flows established by the same underlying physical mechanisms lead to different plasma responses in fusion, laboratory, and space plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Development of a MEMS dual-axis differential capacitance floating element shear stress sensor

A single-axis MEMS wall shear stress sensor with differential capacitive transduction method is produced. Using a synchronous modulation and demodulation interface circuit, the system is capable of making real time measurements of both mean and fluctuating wall shear stress. A sensitivity of 3.44 mV/Pa is achieved, with linearity in response demonstrated up to testing limit of 2 Pa. Minimum detectable signals of 340 μPa at 100 Hz and 120 μPa at 1 kHz are indicated, with a resonance of 3.5 kHz. Multiple full scale wind tunnel tests are performed, producing spectral measurements of turbulent boundary layers in wind speeds ranging up to 0.5 Ma (18 Pa of mean wall shear stress). The compact packaging allows for minimally invasive installation, and has proven relatively robust over multiple testing events. Temperature sensitivity, likely due to poor CTE matching of packaged materials, is an ongoing concern being addressed. These successes are being directly leveraged into a development plan for a dual-axis wall shear stress sensor, capable of producing true vector estimates at the wall.

47 OTHER INSTRUMENTATION↗

Analytic fits to atom-in-jellium shear modulus predictions

Fits to AJ shear modulus calculations from ρ0 to the limit of the corresponding AJ EOS table (usually 1000 ρ0), adjusted to reproduce STP shear modulus where possible. Fitting minimized the fractional difference, so low-pressure points would be reproduced accurately despite the wide-ranging tabulation. AJ calculations were at T=0. Isochoric variation G(T) has been small for all cases spot-tested so far, and may have either sign. The fitted equation usually matches the AJ data to within a few percent. Between numerical noise in the AJ calculation and probably-physical structure not captured by the equation, the deviation could be up to 20% in some places in most models, and 30% in a few. AJ does not capture structural phase transitions or phases stabilized by directional bonds, where the shear modulus may vary by a greater amount. Where possible, STP ρ,G were used as parameters, and low pressure AJ points were de-weighted or removed if necessary. Otherwise, such as where AJ fails to capture solid phases with a significantly different shear modulus, the AJ data were fitted as far down in pressure as possible, G0 was also fitted if necessary, and ρ0 was also adjusted if needed to keep G0>0. The resulting models are not intended for use at low pressure, though some are probably adequate for practical purposes

36 MATERIALS SCIENCE↗

The DECADE cosmic shear project IV: cosmological constraints from 107 million galaxies across 5,400 deg$^2$ of the sky

We present cosmological constraints from the Dark Energy Camera All Data Everywhere (DECADE) cosmic shear analysis. This work uses shape measurements for 107 million galaxies measured through Dark Energy Camera (DECam) imaging of $5,\!412$ deg$^2$ of sky that is outside the Dark Energy Survey (DES) footprint. We derive constraints on the cosmological parameters $S_8 = 0.791^{+0.027}_{-0.032}$ and $Ω_{\rm m} =0.269^{+0.034}_{-0.050}$ for the $Λ$CDM model, which are consistent with those from other weak lensing surveys and from the cosmic microwave background. We combine our results with cosmic shear results from DES Y3 at the likelihood level, since the two datasets span independent areas on the sky. The combined measurements, which cover $\approx\! 10,\!000$ deg$^2$, prefer $S_8 = 0.791 \pm 0.023$ and $Ω_{\rm m} = 0.277^{+0.034}_{-0.046}$ under the $Λ$CDM model. These results are the culmination of a series of rigorous studies that characterize and validate the DECADE dataset and the associated analysis methodologies (Anbajagane et. al 2025a,b,c). Overall, the DECADE project demonstrates that the cosmic shear analysis methods employed in Stage-III weak lensing surveys can provide robust cosmological constraints for fairly inhomogeneous datasets. This opens the possibility of using data that have been previously categorized as ``unusable'' for cosmic shear analyses, thereby increasing the statistical power of upcoming weak lensing surveys.

79 ASTRONOMY AND ASTROPHYSICS↗

Relativistic Shear Flow between Electron–Ion and Electron–Positron Plasmas and Astrophysical Applications

We present particle-in-cell simulation results of relativistic shear boundary layers between electron–ion and electron–positron plasmas and discuss their potential applications to astrophysics. Specifically, we find that in the case of a fast electron–positron spine surrounded by a slow-moving or stationary electron–ion sheath, lepton acceleration proceeds in a highly anisotropic manner due to electromagnetic fields created at the shear interface. While the highest-energy leptons still produce a beaming pattern (as seen in the quasi-stationary frame of the sheath) of order 1/Γ, where Γ is the bulk Lorentz factor of the spine, for lower-energy particles, the beaming is much less pronounced. This is in stark contrast to the case of pure electron–ion shear layers, in which anisotropic particle acceleration leads to significantly narrower beaming patterns than 1/Γ for the highest-energy particles. In either case, shear-layer acceleration is expected to produce strongly angle-dependent lepton (hence, emanating radiation) spectra, with a significantly harder spectrum in the forward direction than viewed from larger off-axis angles, much beyond the regular Doppler boosting effect from a co-moving isotropic lepton distribution. This may solve the problem of the need for high (and apparently arbitrarily chosen) minimum Lorentz factors of radiating electrons, often plaguing current blazar and GRB jet modeling efforts.

79 ASTRONOMY AND ASTROPHYSICS↗

The Roles of Fluid Compression and Shear in Electron Energization during Magnetic Reconnection

Particle acceleration in space and astrophysical reconnection sites is an important unsolved problem in studies of magnetic reconnection. Earlier kinetic simulations have identified several acceleration mechanisms that are associated with particle drift motions. Here, we show that, for sufficiently large systems, the energization processes due to particle drift motions can be described as fluid compression and shear, and that the shear energization is proportional to the pressure anisotropy of energetic particles. By analyzing results from fully kinetic simulations, we show that the compression energization dominates the acceleration of high-energy particles in reconnection with a weak guide field, and the compression and shear effects are comparable when the guide field is 50% of the reconnecting component. Spatial distributions of those energization effects reveal that reconnection exhausts, contracting islands, and island-merging regions are the three most important regions for compression and shear acceleration. This study connects particle energization by particle guiding-center drift motions with that due to background fluid motions, as in the energetic particle transport theory. It provides foundations for building particle transport models for large-scale reconnection acceleration such as those in solar flares.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Relativistic Shear Boundary Layer and the Gamma-Ray Emission of GW170817

We present an analysis of the radiation characteristics of kinetic shear boundary layers created by relativistic plasma jets. Using a model of electromagnetic field data based on particle-in-cell simulations of an electron–ion plasma, we solve the motion of individual test electrons and compute their instantaneous radiated power and peak frequency. By analyzing a large number of test electrons in this manner, we find two distinct electron populations present around the shear boundary layer. The most highly radiative electrons execute looping motion due to crossed electric and magnetic fields as they are accelerated along the bulk flow of the jet, and eventually cross the shear boundary interface at steep angles. Electrons that never cross the shear boundary interface radiate much less energy as a group. Summing over all of the highly radiative electrons, we compute the distribution of the total radiated energy as a function of the angle relative to the bulk flow. Furthermore, this result has important potential implications for the observed radiation output of short gamma-ray bursts viewed at large angles from the jet axis, such as the neutron star merger event GW170817/GRB 170817A.

79 ASTRONOMY AND ASTROPHYSICS↗

Linear and Nonlinear Kelvin–Helmholtz Instability and Magnetohydrodynamic Wave Emission in Sheared Astrophysical Plasma Flows

The evolution of the Kelvin–Helmholtz instability (KHI) and magnetohydrodynamic (MHD) wave emission is investigated at shear-flow boundaries of magnetized plasmas. While MHD wave emission has been suggested to be only possible during the nonlinear stages, we find that there is also significant wave emission during the KHI's linear stages. These emitted MHD waves may have stronger impacts than KHI surface waves since they can act to transport energy away from the local region of the shear flow. The removal of energy from the shear-flow region, instead of just the local redistribution considered in previous studies, and its propagation away from the interface could have major implications for the evolution of astrophysical objects characterized by fast plasma flow shears.

79 ASTRONOMY AND ASTROPHYSICS↗

Reconnection-driven Particle Acceleration in Relativistic Shear Flows

Particle energization in shear flows is invoked to explain nonthermal emission from the boundaries of relativistic astrophysical jets. Yet the physics of particle injection, i.e., the mechanism that allows thermal particles to participate in shear-driven acceleration, remains unknown. With particle-in-cell simulations, we study the development of Kelvin–Helmholtz (KH) instabilities seeded by the velocity shear between a relativistic magnetically dominated electron–positron jet and a weakly magnetized electron–ion ambient plasma. Here, we show that, in their nonlinear stages, KH vortices generate kinetic-scale reconnection layers, which efficiently energize the jet particles, thus providing a first-principles mechanism for particle injection into shear-driven acceleration. Our work lends support to spine-sheath models of jet emission—with a fast core/spine surrounded by a slower sheath —and can explain the origin of radio-emitting electrons at the boundaries of relativistic jets.

79 ASTRONOMY AND ASTROPHYSICS↗

Multi-objective optimization of peel and shear strengths in ultrasonic metal welding using machine learning-based response surface methodology

Ultrasonic metal welding (UMW) is a solid-state joining technique with varied industrial applications. Despite of its numerous advantages, UMW has a relative narrow operating window and is sensitive to variations in process conditions. As such, it is imperative to quantitatively characterize the influence of welding parameters on the resulting joint quality. The quantification model can be subsequently used to optimize the parameters. Conventional response surface methodology (RSM) usually employs linear or polynomial models, which may not be able to capture the intricate, nonlinear input-output relationships in UMW. Furthermore, some UMW applications call for simultaneous optimization of multiple quality indices such as peel strength, shear strength, electrical conductivity, and thermal conductivity. To address these challenges, this paper develops a machine learning (ML)-based RSM to model the input-output relationships in UMW and jointly optimize two quality indices, namely, peel and shear strengths. The performance of various ML methods including spline regression, Gaussian process regression (GPR), support vector regression (SVR), and conventional polynomial regression models with different orders is compared. A case study using experimental data shows that GPR with radial basis function (RBF) kernel and SVR with RBF kernel achieve the best prediction accuracy. The obtained response surface models are then used to optimize a compound joint strength indicator that is defined as the average of normalized shear and peel strengths. In addition, the case study reveals different patterns in the response surfaces of shear and peel strengths, which has not been systematically studied in the literature. While developed for the UMW application, the method can be extended to other manufacturing processes.

42 ENGINEERING↗

SITCOMTN-164: AnaCal Shear Profile of Abell 360 in LSSTComCam Data Preview 1

This technote presents the measurement of the weak-lensing shear profile for the Abell 360 galaxy cluster using LSSTComCam data processed with the AnaCal pipeline. We detail the procedures involved in bright-star masking, source selection, and the estimation of tangential and cross shear around the cluster center. The resulting shear profiles provide key insights into the mass distribution of Abell 360 and demonstrate the capabilities of AnaCal in processing early LSST data, with the tangential shear profile detected at 5σ significance.

79 ASTRONOMY AND ASTROPHYSICS↗