Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “redesign”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Cost analysis of oxygen recovery systems

The design and development of equipment for flight use in earth-orbital programs, when optimally approached cost effectively, proceed through the following logical progression: (1) bench testing of breadboard designs, (2) the fabrication and evaluation of prototype equipment, (3) redesign to meet flight-imposed requirements, and (4) qualification and testing of a flight-ready system. Each of these steps is intended to produce the basic design information necessary to progress to the next step. The cost of each step is normally substantially less than that of the following step. An evaluation of the cost elements involved in each of the steps and their impact on total program cost are presented. Cost analyses of four leading oxygen recovery subsystems which include two carbon dioxide reduction subsystem, Sabatier and Bosch, and two water electrolysis subsystems, the solid polymer electrolyte and the circulating KOH electrolyte are described.

Yakut, M. M.↗
NASA NTRS1973

Comparison of temperature data from an engine investigation for film-cooled and non-film-cooled, panwise-finned vanes incorporating impingement cooling

The experimental temperature characteristics of two spanwise-finned, impingement-cooled vanes, one with film cooling and one without film cooling, were investigated in a modified J-75 research turbojet engine. Values of maximum temperature, average temperature, and maximum chordwise temperature difference were compared for the two vanes at the midspan. An analytical redesign of the two vane configurations indicated that the maximum and average temperatures and the maximum chordwise temperature difference could be significantly lowered. The experimental tests indicated that suction-surface film cooling may cause increased heat transfer near the trailing edge of the vane.

Gauntner, D. J.↗
NASA NTRS1971

Alternate Concepts Study Extension. Volume 1: Executive Summary

An analysis of alternate space shuttle concepts is presented. The two main program alternatives are: (1) phased booster development with an interim solid rocket engine cluster preceding the reusable booster and (2) phased orbiter development with modified avionics, vehicle subsystems, thermal protection system, and redesigned rocket engines. Diagrams of the various concepts are provided. The predicted spacecraft performance capabilities are reported. Project management proposals are submitted.

Source record↗
NASA NTRS1973

Robot computer problem solving system

A robot computer problem solving system which represents a robot exploration vehicle in a simulated Mars environment is described. The model exhibits changes and improvements made on a previously designed robot in a city environment. The Martian environment is modeled in Cartesian coordinates; objects are scattered about a plane; arbitrary restrictions on the robot's vision have been removed; and the robot's path contains arbitrary curves. New environmental features, particularly the visual occlusion of objects by other objects, were added to the model. Two different algorithms were developed for computing occlusion. Movement and vision capabilities of the robot were established in the Mars environment, using LISP/FORTRAN interface for computational efficiency. The graphical display program was redesigned to reflect the change to the Mars-like environment.

Merriam, E. W.↗
NASA NTRS1973

CIT photoheliograph functional verification unit test program

Tests of the 2/3-meter photoheliograph functional verification unit FVU were performed with the FVU installed in its Big Bear Solar Observatory vacuum chamber. Interferometric tests were run both in Newtonian (f/3.85) and Gregorian (f/50) configurations. Tests were run in both configurations with optical axis horizontal, vertical, and at 45 deg to attempt to determine any gravity effects on the system. Gravity effects, if present, were masked by scatter in the data associated with the system wavefront error of 0.16 lambda rms ( = 6328A) apparently due to problems in the primary mirror. Tests showed that the redesigned secondary mirror assembly works well.

Source record↗
NASA NTRS1972

Contamination damage avoidance concepts for propulsion feed system components.

The potential gain in the reliability of reusable long-term mission vehicles through the minimization of component damage due to the ingestion of particulate contamination by feed system components has been recognized by the NASA-LeRC and MDAC, and a program to investigate these problems has been completed. This investigation covered the determination of the cycle life of a typical 2-in. poppet type of shutoff valve in an uncontaminated GH2 environment and then compared this component performance with simulated operation with GN2 and LN2 containing controlled amounts of AL2O2 contaminant particles. The original valve design was tested for contamination damage tolerance characteristics under full flow and cyclic operating conditions, redesigned to improve the damage tolerance to contaminants and then retested. A second method of approach to damage tolerance control was investigated through the evaluation of various types of particulate separation devices. The study included various types of dynamic separators but did not cover conventional filter assemblies.

Endicott, D. L.↗
NASA NTRS1973

Optimal design of structures with buckling constraints.

The paper presents an iterative, finite element method for minimum weight design of structures with respect to buckling constraints. The redesign equation is derived from the optimality criterion, as opposed to a numerical search procedure, and can handle problems that are characterized by the existence of two fundamental buckling modes at the optimal design. Application of the method is illustrated by beam and orthogonal frame design problems.

Kiusalaas, J.↗
NASA NTRS1973

Skylab experience with Apollo docking/latching loads.

Description of the four-year development of Skylab analytical programs, mathematical model complexity, and vibration and load analyses associated with the docking/latching maneuver. Examples are shown where coarse models produced loads in excess of structural capability. However, subsequent model refinement lowered the loads to the point where redesign was not required. A summary of experience gained over a four-year period is presented in the conclusions.

Heath, R. A.↗
NASA NTRS1973

Design of a digital controller for spinning flexible spacecraft.

A new approach to digital control system design is applied to the analysis and design of a practical onboard digital attitude control system for a class of spinning vehicles characterized by a rigid body and two connected flexible appendages. The approach used is to design a continuous-data control system that will provide a satisfactory system response. Then, using the digital redesign method, a digital controller with onboard digital computer is designed to provide a digital control system whose states are similar to those of the continuous system at sampling instants. The simplicity of application of this approach is indicated by an example in which spinning Skylab parameters are used to substantiate the conclusions.

Kuo, B. C.↗
NASA NTRS1973

Acceptance test report (MI-74067-009-00). SVWS access arm (Serial number AA-09-03) (drawing 75M08129-13)

Acceptance tests were conducted at Kennedy Space Center of the Saturn Vehicle Workshop Spacecraft Access Arm and related equipment. The tests were conducted to prove complete system capability to operate satisfactorily under conditions required to support spacecraft operations and activities. The SVWS Access Arm, serial number AA-09-03, is a Command Module Service Arm, S/A 9, which was removed from the mobile launcher and modified to support the SVWS operations. The C/M environmental chamber was removed and a completely new chamber was installed. The retract system was redesigned to remove the automatic/remote control capability and replaced with a local manual control. The SVWS Access Arm System was successfully tested and supported spacecraft processing without major problems.

Hagood, J. T.↗
NASA NTRS1973

Thermally oscillating actuators

The actuator was redesigned to accommodate the new thermal motor for the Helios flipper. This design retained the basic configuration and dimensions of the original actuator. Changes were made primarily to the cradle and motor assembly. Because of the increased dimensions of the thermal motor, it was necessary to increase the diameter of the pellet case and associated parts including the back off spring and the piston return spring. The new springs were designed to yield the same spring rate differential as the originals. The design effort resulted in a new top assembly and approximately twenty sub-assembly and detail drawings. A list of drawings generated by EMR is attached.

Source record↗
NASA NTRS1974

Closed cycle MHD power generation experiments in the NASA Lewis Facility

Many modifications were made in the MHD facility. These include a redesign of the MHD duct interior, addition of mixing bars, increased electrical isolation of all the high temperature components from each other and from ground, and experimentation with various cesium seed vaporization and injection techniques. With the exception of the cesium system which needs further improvement the above modifications were quite successful and resulted in improvements in generator performance. The facility was run for a total of 400 hours in the past year, with 70 hours of this operation at temperatures of 2000 K or more with hot generator walls. With the exception of replacing one cracked brick in the MHD channel no repairs were required in the high temperature loop components for the duration of these tests. Uniform Faraday and Hall voltage profiles were obtained and the Faraday open circuit voltage varied from 90 to 100 percent of the ideal uBh. The magnitudes of the measured parameters are: Faraday open circuit voltage approximately 70 V, total Faraday current approximately 20 A, Hall voltage approximately 250 V, power output approximately 300 W, and power density .036 W/cu cm.

Sovie, R. J.↗
NASA NTRS1974

Design of a digital controller for spinning flexible spacecraft

An approach to digital control system design is applied to the analysis and design of a practical onboard digital attitude control system for a class of spinning vehicles characterized by a rigid body and two connected flexible appendages. The approach used is to design a continuous-data control system that will provide a satisfactory system response. Then, using the digital redesign method, a digital controller with onboard digital computer is designed to provide a digital control system whose states are similar to those of the continuous system at sampling instants. The simplicity of application of this approach is indicated by example. The example, using spinning Skylab parameters, is used to substantiate the conclusions.

Kuo, B. C.↗
NASA NTRS1972

A theoretical and experimental study of wood planer noise and its control

A combined analytical and experimental study of wood planer noise is made and the results applied to the development of practical noise control techniques. The dominant mechanisms of sound generation are identified and an analysis is presented which accurately predicts the governing levels of noise emission. Planing operations in which the length of the board is much greater than the width are considered. The dominant source of planer noise is identified as the board being surfaced, which is set into vibration by the impact of cutterhead knives. This is determined from studies made both in the laboratory and in the field concerning the effect of board width on the resulting noise, which indicate a six decibel increase in noise level for each doubling of board width. The theoretical development of a model for board vibration defines the vibrational field set up in the board and serves as a guide for cutterhead redesign.

Stewart, J. S.↗
NASA NTRS1974

Lunar module voice recorder

A feasibility unit suitable for use as a voice recorder on the space shuttle was developed. A modification, development, and test program is described. A LM-DSEA recorder was modified to achieve the following goals: (1) redesign case to allow in-flight cartridge change; (2) time code change from LM code to IRIG-B 100 pps code; (3) delete cold plate requirements (also requires deletion of long-term thermal vacuum operation at 0.00001 MMHg); (4) implement track sequence reset during cartridge change; (5) reduce record time per cartridge because of unavailability of LM thin-base tape; and (6) add an internal Vox key circuit to turn on/off transport and electronics with voice data input signal. The recorder was tested at both the LM and shuttle vibration levels. The modified recorder achieved the same level of flutter during vibration as the DSEA recorder prior to modification. Several improvements were made over the specification requirements. The high manufacturing cost is discussed.

Source record↗
NASA NTRS1973

Single photon detection and sub-nanosecond timing resolution with RCA C31034 photomultiplier

The very high quantum efficiencies and low dark count rates achieved with selected RCA C31034 photomultipliers make them attractive candidates for single photoelectron fast timing experiments. Single photoelectron plateau counting and a timing resolution of 0.60 nsec (FWHM) were obtained using fast amplifiers, constant fraction timing discriminators, and a pulsed light emitting diode. A redesign of the C31034 incorporating features of the very fast C31024 is suggested to yield even better timing resolution.

Reisse, R.↗
NASA NTRS1974

Optimal aeroelastic design of an oblique wing structure

A procedure is presented for determining the optimal cover panel thickness of a wing structure to meet specified strength and static aeroelastic divergence requirements for minimum weight. Efficient reanalysis techniques using discrete structural and aerodynamic methods are used in conjunction with redesign algorithms driven by optimality criteria. The optimality conditions for the divergence constraint are established, and expressions are obtained for derivatives of the dynamic pressure at divergence with respect to design variables. The procedure is applied to an oblique wing aircraft where strength and stiffness are critical design considerations for sizing the cover thickness of the wing structure.

Gwin, L. B.↗
NASA NTRS1974

Closed cycle MHD power generation experiments in the NASA Lewis facility

Discussion of the performance improvements achieved through some modifications made in the closed cycle MHD facility. These modifications include a redesign of the MHD duct interior, addition of mixing bars, increased electrical isolation, and experimentation with various cesium seed vaporization and injection techniques. Uniform Faraday and Hall voltage profiles were obtained, and the Faraday open circuit voltage varied from 90 to 100% of the ideal uBh.

Sovie, R. J.↗