Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “raw materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

High-Precision Measurement of Eu/Eu* in Geological Glasses via LA-ICP-MS Analysis

Elemental fractionation during laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analysis has been historically documented between refractory and volatile elements. In this work, however, we observed fractionation between light rare earth elements (LREEs) and heavy rare earth elements (HREEs) when using ablation strategies involving large spot sizes (greater than 100 millimeters) and line scanning mode. In addition: (1) ion yields decrease when using spot sizes above 100 millimeters; (2) (Eu/Eu*)(sub raw) (i.e. Europium anomaly) positively correlates with carrier gas (He) flow rate, which provides control over the particle size distribution of the aerosol reaching the ICP; (3) (Eu/Eu*)(sub raw) shows a positive correlation with spot size, and (4) the changes in REE signal intensity, induced by the He flow rate change, roughly correlate with REE condensation temperatures. The REE fractionation is likely driven by the slight but significant difference in their condensation temperatures. Large particles may not be completely dissociated in the ICP and result in preferential evaporation of the less refractory LREEs and thus non-stoichiometric particle-ion conversion. This mechanism may also be responsible for Sm-Eu-Gd fractionation as Eu is less refractory than Sm and Gd. The extent of fractionation depends upon the particle size distribution of the aerosol, which in turn is influenced by the laser parameters and matrix. Ablation pits and lines defined by low aspect ratios produce a higher proportion of large particles than high aspect ratio ablation, as confirmed by measurements of particle size distribution in the laser induced aerosol. Therefore, low aspect ratio ablation introduces particles that cannot be decomposed and/or atomized by the ICP and thus results in exacerbated elemental fractionation. Accurate quantification of REE concentrations and Eu/Eu* requires reduction of large particle production during laser ablation. For the reference materials analyzed in this work, the 100 millimeters spot measurements of Eu/Eu* agreed with GeoRem preferred values within 3 percent. Our long-term analyses of Eu/Eu* in MPI-DING glass KL-2G and USGS glass BIR-1G were reproducible at 3 percent (2 RSD).

geological glasses↗
DOE OSTI2026

Data supporting the manuscript "Nanometer Scale Imaging to Develop Quantitative Descriptors of Bipolar Membrane Junction Structure"

This dataset contains atomic force microscopy images associated with the manuscript "Nanometer Scale Imaging to Develop Quantitative Descriptors of Bipolar Membrane Junction Structure" by Maria Kelly, Emily R. Dunn, Ellis A. Spickermann, Josephine N. Gruber, César A. Lasalde-Ramírez, P. N. Romero Zavala, Éowyn Lucas, Ankur Gupta, Harry A. Atwater, and Wilson A. Smith. The dataset contains both raw images as well as segmented images produced by the image processing workflow described in the manuscript. A readme file and meta data file are included to provide additional details regarding the sample identity, image acquisition parameters, and file naming scheme.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Development of Machine Learning Algorithms to Segment and Study Images of Astromaterial Samples

Introduction: Micrometer-scale chemical analyses of chondritic meteorites and mission-returned asteroid samples can reveal details of the physical and chemical processes operating in the early solar system, including processes that gave rise to planets, moons, and minor bodies. These primitive astromaterials are comprised of chondrules, calcium- and aluminum-rich inclusions (CAI), and many other silicates, oxides, metals, sulfides, and fine-grained materials. The chemical and mineralogical complexity of these samples, vast populations of different components, and heterogeneity across mm to km scales, all limit our understanding of the origin and evolution of these materials. Here, we describe recent efforts to use machine learning techniques to automate the segmentation of chemical maps of chondritic meteorites, designed to aid studies of asteroid samples returned by spacecraft. By automating the task of segmentation it will become possible to rapidly analyze and interpret the sizes, shapes, mineralogy, chemistry, and other properties of every chondrule, calcium- and aluminum-rich inclusion (CAI) and other clast within and between asteroid samples. Sample return missions significantly accelerate and heighten the need to develop such new data analysis techniques, and associated data repositories. Techniques: Neural networks require abundant training data, i.e. images which have been segmented by a human user. We have manually segmented data available from previous petrologic and chemical work at NASA Johnson Space Center and the American Museum of Natural History [1-4]. These data were derived from energy- and wavelength-dispersive X-ray spectroscopy (EDS, WDS) mapping of samples from many chondrite groups. The Deeplabv3+ [5] neural network architecture was trained on human-labeled masks and used to create machine-labeled masks. Several different algorithms were investigated, with inputs ranging from common RGB image formats through to hyperspectral datasets, with raw data comprising greyscale maps of Mg, Ca, and Al, with or without Si, Fe, Ti for both EDS and WDS data, and extending to other elements in EDS only. Each greyscale image was paired with a binary mask for each labelled particle type. Results: The trained algorithms can segment (Fig 1), classify, and measure the dimensions of thousands of particles in chemical maps of a standard 1-inch round petrographic section in seconds to minutes, rather than many hours needed by a human. Accuracy of the algorithms varied from chondrite to chondrite and across particle types. Further results and details of the algorithms will be presented at the workshop. Future directions: Machine learning has the potential to revolutionize our understanding of complex particle populations contained within primitive astromaterial, with segmentation being a critical first step. Example applications include better understanding of particle transport, nebular reservoirs, parent body accretion, and a deeper understanding of the relationships between particle populations and bulk rock elemental and isotopic compositions. In addition to benefits that machine learning can bring to individual researchers, building a community data repository of thousands to millions of particles across hundreds of samples will open up many other possibilities. For example, with a large enough dataset it will be possible to search for exceptionally closely matching particles across disparate samples. Such a capability would enable a single CAI from OSIRISREx or Hayabusa/II samples to be matched to chondritic CAIs that exhibit near-identical size, texture, and mineralogy, down to the level of similar core phenocrysts, zonation, and rim sequences. Such comparative analyses will help to disentangle precursor chemistry, chronology, gas/dust reservoirs during heating, and accretion. Such an endeavor would be impossible without machine learning and a large community data repository of astromaterial chemical/mineralogic maps.

Machine Learning↗
DOE OSTI2021

Corrosion of Ferrous Structural Alloys in Biomass Derived Fuels and Organic Acids

This work investigated the corrosivity of biomass-derived liquid fuels and organic acids associated with bio-oils and conducted a corrosion compatibility evaluation of several structural ferrous alloys in the fuels and acids. Here, the acidity parameters and solution conductivity values were higher in raw pyrolysis bio-oils than postprocessed oils with significant corrosion attack for carbon steel and Fe-2.25Cr-1Mo. However, higher-grade stainless steels, ferritic Fe-15Cr (15Cb) and austenitic types 304L and 316L, showed negligible corrosion loss, whereas lower-Cr ferritic grades 409, 410, and 416 were attacked. Metal leaching tests and electrochemical impedance spectroscopy measurements revealed superior corrosion resistance of 316 over 410 stainless steels in solutions of formic and oxalic acids that can be present in bio-oils. The corrosion evaluation methods utilized in this work provide effective screening tools to identify the compatible structural alloys for bio-oils.

09 BIOMASS FUELS↗
NASA NTRSDate not supplied

NDE Methods and Capabilities Handbook – Resources for the Composites NDE Community

Composite structures are often difficult to inspect due to the anisotropic nature of the material systems and the range of flaws and defects that can arise in the manufacturing process. NASA’s Advanced Composites Project, a public-private partnership between government, universities and industry, sought to address improved methods, tools, and protocols to reduce the development and certification timeline for composite materials and structures. The rapid inspection of composites was one of the three focused research areas of the project. One deliverable of the project was to develop an NDE Methods and Capabilities Handbook. This Handbook provides a publicly available guidance document that facilitates the selection of appropriate NDE techniques and provides recommended protocols for detecting and characterizing common flaw types in solid laminate carbon fiber reinforced polymer composite (CFRP) structures. The Handbook seeks to reduce the time required to develop qualified inspection processes for composite aircraft structures during the development, certification, and manufacturing phases by providing a reference that helps minimize trial and error and provides guidance on best practices, techniques, and settings, for specific flaw types and geometries. NDE techniques include, but are not limited to ultrasound, laser based ultrasound, infrared thermography, and x-ray CT. Flaw types include, but are not limited to porosity, delamination, voids, AFP defects and impact damage. The Handbook contains details such as inspection parameters, data analysis techniques, inspection efficiency (speed & cost), and limitations. This presentation will describe key Handbook activities with examples of the techniques and flaw types examined by the Advanced Composite Consortium members. Availability of the fabricated NDE standards as well as the raw data collected on the standards by the Consortium members to the NDE community is discussed.

Patricia A Howell↗
NASA NTRSDate not supplied

NDE Methods and Capabilities Handbook - Resources for the Composites NDE Community

Composite structures are often difficult to inspect due to the anisotropic nature of the material systems and the range of flaws and defects that can arise in the manufacturing process. NASA’s Advanced Composites Project, a public-private partnership between government, universities and industry, sought to address improved methods, tools, and protocols to reduce the development and certification timeline for composite materials and structures. The rapid inspection of composites was one of the three focused research areas of the project. One deliverable of the project was to develop an NDE Methods and Capabilities Handbook. This Handbook provides a publicly available guidance document that facilitates the selection of appropriate NDE techniques and provides recommended protocols for detecting and characterizing common flaw types in solid laminate carbon fiber reinforced polymer composite (CFRP) structures. The Handbook seeks to reduce the time required to develop qualified inspection processes for composite aircraft structures during the development, certification, and manufacturing phases by providing a reference that helps minimize trial and error and provides guidance on best practices, techniques, and settings, for specific flaw types and geometries. Techniques include, but are not limited to ultrasound, laser based ultrasound, infrared thermography, and x-ray CT. Flaw types include, but are not limited to porosity, delaminations, voids, Automated Fiber Placement (AFP) defects and impact damage. The Handbook contains details such as inspection parameters, data analysis techniques, inspection efficiency and limitations. This paper describes key Handbook activities with examples of the techniques and flaw types examined by the Advanced Composite Consortium members. Availability to the NDE community of the fabricated NDE standards as well as the raw data collected on the standards by the Consortium members is discussed.

nondestructive evaluation↗
NASA NTRSDate not supplied

NDE Methods and Capabilities Handbook - Resources for the Composites NDE Community

Composite structures are often difficult to inspect due to the anisotropic nature of the material systems and the range of flaws and defects that can arise in the manufacturing process. NASA’s Advanced Composites Project, a public-private partnership between government, universities and industry, sought to address improved methods, tools, and protocols to reduce the development and certification timeline for composite materials and structures. The rapid inspection of composites was one of the three focused research areas of the project. One deliverable of the project was to develop an NDE Methods and Capabilities Handbook. This Handbook provides a publicly available guidance document that facilitates the selection of appropriate NDE techniques and provides recommended protocols for detecting and characterizing common flaw types in solid laminate carbon fiber reinforced polymer composite (CFRP) structures. The Handbook seeks to reduce the time required to develop qualified inspection processes for composite aircraft structures during the development, certification, and manufacturing phases by providing a reference that helps minimize trial and error and provides guidance on best practices, techniques, and settings, for specific flaw types and geometries. Techniques include, but are not limited to ultrasound, laser based ultrasound, infrared thermography, and x-ray CT. Flaw types include, but are not limited to porosity, delaminations, voids, Automated Fiber Placement (AFP) defects and impact damage. The Handbook contains details such as inspection parameters, data analysis techniques, inspection efficiency and limitations. This presentation will describe key Handbook activities with examples of the techniques and flaw types examined by the Advanced Composite Consortium members. Availability to the NDE community of the fabricated NDE standards as well as the raw data collected on the standards by the Consortium members is discussed.

Nondestructive Evaluation↗
DOE OSTI2020

Coupled Hydrothermal Extraction and Ligand-Associated Swellable Glass Media Recovery of Rare Earth Elements from Coal Fly Ash (Final Report)

Wayne State University (WSU) researchers, in collaboration with the University of California-Los Angeles (UCLA) and Los Alamos National Laboratory (LANL), have successfully developed a new sorbent media used in a process that concentrated the rare earth content in a coal fly ash sample from southeast MI by >350×, resulting in >13 wt% REO powder. The project developed a new DTPA-associated media that was used to concentrate total REEs. This project demonstrated a coupled hydrothermal extraction and solid-liquid recovery process that produced REO powder from raw fly ash while nearly eliminating the use of organic solvents. The project successfully: 1) identified a commercially viable ash supply with >$2.5 M in REO value being deposited monthly, 2) hydrothermally extracted >77% of REEs in coal fly ash (20% more than acid alone), 3) developed a new sorbent media that was used to concentrate REEs, 4) and engineered a process that resulted in a >13 wt% REO powder. The media also demonstrates a selectivity for mid and heavy REEs over Ce and La and the potential for use in separating individual rare earth elements. An invention disclosure for the sorbent media has been filed with WSU and a patent application will be submitted in the near future. The project examined the potential to couple hydrothermal leaching of coal fly ash with the engineering of a custom ligand-associated media to provide an organic solvent-free method of extracting and recovering REEs. Fly ash feedstock was collected from Detroit area coal-fired power plants, characterized for REE content, and subjected to a bench-top batch hydrothermal leaching/dissolution process inside custom-build pressure reactors at Los Alamos National Laboratory (LANL). This process applied a dissolution technique previously developed to process spent nuclear fuel and other nuclear materials. The modified ash was acidified and the resulting leachate was enriched with REEs along with Ca, Al, and Si. Ligands known to be effective in lanthanide/actinide separation were evaluated based on a series of criteria such as selectivity and association to organosilica through hydrophobicity. Batch experiments were conducted to establish the best conditions (e.g., pH, eluent, etc.) and best ligand systems for the effective extraction of REEs from the alkaline feed solution obtained from the hydrothermal leaching process. Once the organosilica-ligand extraction media was developed for REE concentration, an acidic solution was used to back extract and concentrate the REEs into a heavily REE-laden strip solution. The REEs in the strip solution were precipitated with oxalate to produce rare earth oxides.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Direct Extraction of Uniform Lignin Microspheres from Bamboo Using a Polyol-Based Deep Eutectic Solvent

Conventional preparation of lignin micro-/nano-particles (LMNPs) often needs multiple steps accompanied by high cost, low efficiency, and low yield. Herein, this study established a polyhydric alcohol-based deep eutectic solvent (PA-DES) fractionation for direct LMNP assembly from raw lignocellulose. The results indicated that lignin was significantly extracted by 41.55–70.33% depending on the PA-DES varieties. With lignin removal, the substrate showed high glucan enzymatic saccharification from 70.44 to 100%. Specially, over 90% lignin could be recovered in each PA-DES, and the obtained LMNPs showed quite uniform spherical morphology with a tunable size of 550–3254 nm and narrow polydispersity index (PDI) of 0.295–0.398. The proposed DES showed a near theoretical recovery yield, which still featured excellent fractionation performance even after three cycles of reuse. In conclusion, the findings highlight the simultaneous utilization of cellulose and lignin in a one-pot biomass fractionation under mild conditions with sugars and LMNPs as the coproducts.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Two-stage formation-energy correction (NbZr, TaZr, VZr)

This bundle contains the scripts, the raw and corrected per-structure data, and the manuscript plots for the NbZr / TaZr / VZr BCC binary formation energies and the associated RMSDs. Why a two-stage correction is necessary: The "raw" formation energy of every relaxed VASP configuration is computed in the usual way, FE_raw(c) = E_alloy(c) - sum_i x_i * E_pure_i , where E_pure_i are the per-atom total energies of the pure-element reference structures (Nb, Ta, V, Zr in the same BCC supercell, with identical INCAR / KPOINTS / PAW choices). With perfectly consistent reference runs the raw FE should vanish at the two pure-element endpoints (x = 0 and x = 1) by construction. In practice this does not hold for two reasons that are present in our dataset: 1. Reference-energy inconsistency (composition-dependent bias). Even with identical input parameters, the pure-element runs (stored in `corrected_DFT_pure_element_runs/`) differ slightly from the values that would be implied by the alloy runs at near-pure compositions (a few meV/atom). This bias is approximately linear in concentration, because the residual error in E_pure_Nb (or E_pure_Ta / E_pure_V) propagates into FE_raw(c) as (1 - x) * dE_pure_1, and the corresponding error in E_pure_Zr propagates as x * dE_pure_2. Left uncorrected, this produces a non-physical "tilt" of FE_raw(x) and shifts the entire FE-vs-x cloud away from zero at the endpoints. 2. Endpoint anchoring against the audited true endpoints. The strict endpoint values (FE_x0_meVatom, FE_x1_meVatom in `corrected_fe_strict_endpoints_20260518/strict_endpoint_check_20260518.csv`) were re-derived from an independent cross-check of the pure-element runs. After stage 1 removes the linear bias, the near-pure compositions in the alloy dataset still extrapolate to values that differ slightly from these audited endpoints — because stage 1 is fit from a few near-end alloy bins, not from the audited pure-element references themselves. The README.txt file discusses how these issues are addressed by the two-stage correction, and describes folder layout, pipeline summary, and how to re-run.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Baseline Characterization Database Verification Report – 2114 Billet A20568

This ECAR provides the results of a validity evaluation of the physical and mechanical property data collected on a billet of nuclear-grade graphite (i.e., 2114 Billet A20568) in support of the ART Baseline Graphite Characterization Program.1,2 Millions of raw data points have been collected during testing and quantification analyses for these billets. The summary scalar property values and supplementary traceability data are collected into comprehensive spreadsheets. Data sets are composed of single billets of graphite for any given grade, organized by mechanical test-specimen type, and further subdivided into individual spreadsheet tabs according to the specific test or evaluation being performed. A direct analysis of properties was not conducted, and this report does not provide information on the validity or performance characteristics of the graphite itself. Rather, this report is intended as a verification of the completeness of actual data collected in accordance with PLN-3467, “Baseline Graphite Characterization Plan: Electromechanical Testing,”3 and their representation of the measurement and test results with sole regard to the graphite billets under evaluation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Tempering kinetics during multilayer laser additive manufacturing of a ferritic steel

Grade 91 steel forms martensite during additive manufacturing and the extent of tempering of martensite significantly affects the mechanical properties of parts. Currently, there is a lack of quantitative understanding of the tempering kinetics for Grade 91 steel, and as a result, the effects of repeated thermal cycles on properties for different processing conditions cannot be determined. Here we evaluate the tempering kinetics by determining the constant terms in the Johnson Mehl Avrami kinetic equation from the tempering data available in the literature and the thermal cycles computed using a rigorously-tested heat and fluid flow model of multi-layer additive manufacturing. The raw tempering data are cleaned using a neural network to enhance accuracy. The lower layers experience repeating cycles of heating and cooling when the upper layers are added. As a result, the hardness is reduced owing to the tempering of martensite. In contrast, martensite formed in the upper layers is not tempered to the same extent and the hardness remains high. Therefore, the hardness of the part increases with the distance from the substrate. Variations in the heat input at different laser powers and scanning speeds significantly affect the extent of tempering. Finally, since the method used here can provide a quantitative understanding of the tempering of martensite and the spatial variation in hardness, it can be used to tailor the microstructure and hardness of heat treatable printed metallic parts.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ambient Mass Spectrometry Rapid Analysis Methods for Trace Inorganics

The ability to rapidly detect and characterize the chemistry of trace quantities of inorganic species has multiple potential applications, including nuclear safeguards, nuclear forensics, and environmental monitoring. Some mass spectrometric methods currently exist, but they are costly and time-intensive, often destroying chemical information in the process of ionization. Ambient mass spectrometry is a relatively new analytical method in which samples are introduced to the mass spectrometer from atmospheric pressure, rather than from high vacuum. Ambient MS can operate with gentler ionization methods such as electrospray ionization (ESI) and paper-spray ionization (PSI), reducing fragmentation and preserving the chemical information of the analyte. This may be useful for determining the intended purpose of material in a sample. Strontium, part of nuclear fallout, is analyzed here to test these new analytical methods for viability. Electrospray ionization mass spectrometry functions by spraying the sample as a solution through a needle charged to a few kV. A nebulizing gas flows out along with the sample to create the spray before droplets enter a drying chamber with heated drying gas to remove the solvent molecules. From there bare analyte ions enter the mass spectrometer. This method has the advantage of relatively fast sample preparation and stable ionization. More stable ionization produces higher-quality data. Paper-spray ionization mass spectrometry operates by applying sample to a paper triangle. The paper triangle is then electrified in a metal clamp to a few kV before spray solvent is applied. The spray solvent transports analyte in the sample to the tip, where it is ionized and enters the mass spectrometer. One advantage of this method is reduced sample preparation - an analyst can even swipe a surface and cut a triangle directly from the swipe. The data analysis serves to rapidly process tens of samples all at once. The mass spectrometer outputs a file containing a few hundred spectra for each sample. The pipeline processes each one to identify peaks of interest. A full palette of data analysis metrics are generated, including plots of the raw data and plots of calculated values such as isotopic ratios. The pipeline filters the raw data to remove noise and background peaks, as well as peaks representing detector saturation. A heat map is generated to show the overall spectrum in mass-time- intensity space. Post-processing, we obtained the desired calibration curves, demonstrating that both ESI-MS and PSI-MS are viable methods for quantifying trace amounts of inorganics while retaining their chemical speciation information. ESI-MS demonstrated a linear response region of 100 ppb to 20 ppm, with a limit-of-detection of around 100 ppb. At top left is an example spectrum with the {sup 88}SrNO{sub 3} peak identified to show the retention of chemical speciation. PSI-MS showed a linear response region of around 1 ppb to 1 ppm, with a limit-of-detection of near 1 ppb. PSI-MS produced more erratic results than ESI-MS, likely due to the variability in ionization resulting from manual positioning of the paper triangle near the MS inlet. Future efforts will focus on improving the repeatability of PSI-MS as well as analyzing other species of interest such as cerium and uranium. Improvements will also be made to create more reliable data extraction and intelligent data filtering.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Review of thermophysical property methods applied to fueled and un-fueled molten salts

Recent investigation into designs of molten salt reactors (MSR) requires accurate data of candidate salts. Review of the literature shows lacking thermophysical (TP) property data for coolants and fuel-bearing salts of Advanced High Temperature Reactors (AHTR). Measurement uncertainties of current data are even more deficient, and this affects ongoing research where MSR modeling and testing are being performed. Melting temperature, viscosity, density, specific heat capacity, and thermal and electrical conductivity measurements are often not arranged together or discussed in great detail, especially for fuel-bearing salts. Raw data from key findings spanning over 70 years for LiF, LiF-BeF 2 , LiF-NaF-KF, KCl-MgCl 2 , KF-ZrF 4 , and NaF-KF-MgF 2 have been organized and presented here. Brief description of methods used to obtain these results, in addition to the TP data of some of these salts as fuel carriers, has also been discussed. Thermal conductivity data are particularly weak due to older, high-error measurement techniques. More recent measurement systems to evaluate salt thermal conductivity show promise for obtaining consistent absolute values. This work concludes that measurement systems such as transient hot-wire method, forced Rayleigh scattering, and laser flash analysis provide the most promise to fill these data gaps and reduce current uncertainty in thermal conductivity measurements of both fueled and un-fueled molten salts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Facile and Scalable Synthesis of Metal- and Nitrogen-Doped Carbon Nanotubes for Efficient Electrochemical CO 2 Reduction

Metal- and nitrogen-doped carbon (M–N–C) is a promising material to catalyze electrochemical CO 2 reduction reaction (CO 2 RR). However, most M–N–C catalysts in the literature require complicated synthesis procedures and produce small quantities per batch, limiting the commercialization potential. In this work, we developed a simple and scalable synthesis method to convert metal-impurity-containing commercial carbon nanotubes (CNTs) and nitrogen-containing organic precursors into M–N–C via one-step moderate-temperature (650 °C) pyrolysis without any other treatment nor the need to add metal precursors. Batches of catalysts in varied mass up to 10 g (150 mL in volume) per batch were synthesized, and repeatable catalytic performances were demonstrated. To the best of our knowledge, the 10 g batch is one of the largest batches of CO2RR catalysts synthesized in the literature while requiring minimal synthesis steps. The catalyst possessed single-atomic iron–nitrogen (Fe–N) sites, enabling a high performance of >95% CO product selectivity at a high current density of 400 mA/cm 2 and high stability for 45 h at 100 mA/cm 2 in a flow cell testing. The catalyst outperformed a benchmark noble-metal nanoparticle catalyst and achieved longer stability than many other reported M–N–C catalysts in the literature. The scalable and cost-effective synthesis developed in this work paves a pathway toward practical CO 2 RR applications. The direct utilization of metal impurities from raw CNTs for efficient catalyst synthesis with minimal treatment is a green and sustainable engineering approach.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Emergent Nanostructure and Ion Transport in Polyzwitterion/Polyanion Blends

We investigated blends of poly(1-(3-sulfonatopropyl)-2-vinylpyridinium) (P2VPPS) and poly(lithium (trifluoromethane)sulfonimide methacrylate) (poly(MTFSI)Li) at varying molar ratios to gain a mechanistic understanding of ionic conductivity in a miscible polyzwitterion/polyanion system. This dataset contains the raw numerical data corresponding to the figures in the manuscript. The data files include the following information: (1) Experimental Data – includes X-ray and neutron scattering measurements, broadband dielectric spectroscopy (BDS) data, extracted DC conductivity values, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) results, extracted glass transition temperatures, etc. (2) CGMD Data – includes molecular dynamics (MD) trajectory files and computed structural correlations. All data files are organized/named according to the figure numbers in the manuscript.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Baseline Characterization Database Verification Report ? NBG-17 Billet V104

The purpose of this report is to present data collected in the Baseline Graphite Characterization Program, which is directly tasked with supporting the Idaho National Laboratory’s (INL’s) research and development efforts on the Advanced Reactor Technologies (ART) Program. This program populates a comprehensive database that reflects the baseline properties of nuclear-grade graphite regarding individual grade, billet, and position within individual billets. The physical- and mechanical-property information being collected will be transferred to the Nuclear Data Management and Analysis System (NDMAS), and that database will help populate the handbook of property data available to member nations of the Generation-IV International Forum. Transfer of these data from the applicable technical lead to the dissemination databases available to other end users requires a full review of the test procedures and data-collection efforts through an analysis of the multiple summary spreadsheets and values being collected. This report represents the analysis for NBG-17 Billet V104 and facilitates release of associated data to the NDMAS custodians. Millions of raw data points have been collected during testing and quantification analyses for these billets. The summary scalar property values and supplementary traceability data are collected into comprehensive spreadsheets. Data sets are composed of single billets of graphite for any given grade, organized by mechanical test-specimen type, and further subdivided into individual spreadsheet tabs according to the specific test or evaluation being performed. A direct analysis of properties was not conducted, and this report does not provide information on the validity or performance characteristics of the graphite itself. Rather, this report is intended as a verification of the completeness of actual data collected in accordance with PLN-3467, “Baseline Graphite Characterization Plan: Electromechanical Testing,” [1] and PLN-3348 “Graphite Mechanical Testing” [2] and their representation of the measurement and test results with sole regard to the graphite billets under evaluation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Data for "Relative Reactivity and Bioavailability of Mercury Sorbed to or Coprecipitated with Aged Iron Sulfides"

The potential for inorganic mercury (Hg) to be converted to methylmercury depends, in part, on the chemical form of Hg and its bioavailability to anaerobic microorganisms that can methylate Hg. In anaerobic settings, Hg can be associated with sulfide phases, including ferrous iron sulfide (FeS), which can sorb or coprecipitated with Hg. The objective of this study was to determine if the aging state of FeS alters the Hg coordination environment as well as the reactivity and bioavailability of sorbed and coprecipitated Hg species. FeS particles were synthesized with and without Hg2+ and aged in anaerobic conditions for multiple time frames spanning from 1 hour to 1 month. For FeS particles synthesized without Hg, Hg2+ was subsequently sorbed to the FeS for 1 day. Analysis of Hg speciation of these materials by X-ray absorption near edge spectroscopy revealed a predominance of 4-coodinate Hg-S species in the sorbed Hg-FeS solids and a mixture of 2- and 4-coordinate Hg-S in the coprecipitated Hg-FeS. The leaching potential of the Hg was assessed by exposing the particles to a solution of dissolved glutathione (a thiolate-based Hg chelator). As expected, the sorbed Hg-FeS released more soluble Hg compared to the co-precipitated Hg-FeS. However, when these particles were exposed to Desulfovibrio desulfuricans ND132 (a known Hg methylator), more Hg was methylated from the co-precipitated Hg-FeS than the sorbed Hg-FeS, consistent with expectations from the Hg-S coordination state and inconsistent with the selective leaching results. Overall, these results suggest that the bioavailability of particulate Hg cannot be easily discerned by leaching potential into bulk solution. Rather, bioavailability entails more subtle interactions at particle-cell interfaces and perhaps correlates with the local Hg-S coordination state in the particles. This data package contains data shown in the referenced publication, including all figures. Each figure is available in the respective *.csv file and a summary of all files are also included in the the xlsx file. Additional formatted data include X-ray diffraction data of the FeS solids are also available in a HPF format (Panalytical software), X-ray absorption spectroscopy data as *.prj files (Athena), and X-ray fluorescence data in its raw data form.

54 ENVIRONMENTAL SCIENCES↗