Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “prediction methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Advanced prediction technique for the low speed aerodynamics of V/STOL aircraft. Volume 2: User's manual

A computerized prediction method known as the Vought V/STOL Aircraft Propulsive Effects computer program (VAPE) for propulsive induced forces and moments in transition and Short TakeOff and Landing (STOL) flight is improved and evaluated. The VAPE program is capable of evaluating: (1) effects of relative wind about an aircraft, (2) effects of propulsive lift jet entrainment, vorticity and flow blockage, (3) effects of engine inlet flow on the aircraft flow field, (4) engine inlet forces and moments including inlet separation, (5) ground effects in the STOL region of flight, and (6) viscous effects on lifting surfaces.

Beatty, T. D.↗
NASA NTRS1984

An Analysis of Wave Interactions in Swept-Wing Flows

Crossflow instabilities dominate disturbance growth in the leading-edge region of swept wings. Streamwise vortices in a boundary layer strongly influence the behavior of other disturbances. Amplification of crossflow vortices near the leading edge produces a residual spanwise nonuniformity in the mid-chord regions where Tollmien-Schlichting (T-S) waves are strongly amplified. Should the T-S wave undergo double-exponential growth because of this effect, the usual transition prediction methods would fail. The crossflow/Tollmien-Schlichting wave interaction was modeled as a secondary instability. The effects of suction are included, and different stability criteria are examined. The results are applied to laminar flow control wings characteristic of energy-efficient aircraft designs.

Reed, H. L.↗
NASA NTRS1982

Comparison of Flight Measured, Predicted and Wind Tunnel Measured Winglet Characteristics on a KC-135 Aircraft

One of the objectives of the KC-135 Winglet Flight Research and Demonstration Program was to obtain experimental flight test data to verify the theoretical and wind tunnel winglet aerodynamic performance prediction methods. Good agreement between analytic, wind tunnel and flight test performance was obtained when the known differences between the tests and analyses were accounted for. The flight test measured fuel mileage improvements for a 0.78 Mach number was 3.1 percent at 8 x 10(5) pounds W/delta and 5.5 percent at 1.05 x 10(6) pounds W/delta. Correcting the flight measured data for surface pressure differences between wind tunnel and flight resulted in a fuel mileage improvement of 4.4 percent at 8 x 10(5) pounds W/delta and 7.2 percent at 1.05 x 10(6) pounds W/delta. The performance improvement obtained was within the wind tunnel test data obtained from two different wind tunnel models. The buffet boundary data obtained for the baseline configuration was in good agreement with previous established data. Buffet data for the 15 deg cant/-4 deg incidence configuration showed a slight improvement, while the 15 deg cant/-2 deg incidence and 0 deg cant/-4 deg incidence data showed a slight deterioration.

Dodson, R. O., Jr.↗
NASA NTRS1982

Study of aerodynamic technology for single-cruise-engine V/STOL fighter/attack aircraft

A viable, single engine, supersonic V/STOL fighter/attack aircraft concept was defined. This vectored thrust, canard wing configuration utilizes an advanced technology separated flow engine with fan stream burning. The aerodynamic characteristics of this configuration were estimated and performance evaluated. Significant aerodynamic and aerodynamic propulsion interaction uncertainties requiring additional investigation were identified. A wind tunnel model concept and test program to resolve these uncertainties and validate the aerodynamic prediction methods were defined.

Hess, J. R.↗
NASA NTRS1982

Acoustic methodology review

It is important for industry and NASA to assess the status of acoustic design technology for predicting and controlling helicopter external noise in order for a meaningful research program to be formulated which will address this problem. The prediction methodologies available to the designer and the acoustic engineer are three-fold. First is what has been described as a first principle analysis. This analysis approach attempts to remove any empiricism from the analysis process and deals with a theoretical mechanism approach to predicting the noise. The second approach attempts to combine first principle methodology (when available) with empirical data to formulate source predictors which can be combined to predict vehicle levels. The third is an empirical analysis, which attempts to generalize measured trends into a vehicle noise prediction method. This paper will briefly address each.

Schlegel, R. G.↗
NASA NTRS1984

Subsonic/transonic prediction capabilities for nozzle/afterbody configurations

Prediction methods for several nozzle/afterbody flow problems at subsonic and transonic speeds are presented. These methods range from viscous-inviscid interaction methods to solutions for the Navier-Stokes equations in two and three dimensions. The problems addressed are the flow around isolated axisymmetric nozzles, isolated nonaxisymmetric nozzles, and axisymmetric nozzles with empennage. An assessment of the state of development of the methods via comparisons with experimental data is presented.

Wilmoth, R. G.↗
NASA NTRS1984

An AOTV aeroheating and thermal protection study

The aerothermodynamics and thermal protection of aerobraking orbital transfer vehicles are studied with a view toward design methodology and technology requirements. A particular class of geometries is investigated: the ellipsoidally blunted raked-off elliptic cone. Discussed are the influence of various geometrical parameters on the trajectory and the heat flux as well as heating prediction methods ranging from an engineering correlation formula to computational solutions of the Navier-Stokes equations. Finite-rate catalytic thermal protection materials and gas radiation are considered. Estimates of the specific mass of possible thermal protection systems indicate that support structure is a large contributor to the aerobrake mass as compared with the thermal protection insulation itself. Sizing curves are included which enable the designer to estimate the size aerobrake required from heating considerations for different mass vehicles having aerobrakes of several specific masses.

Scott, C. D.↗
NASA NTRS1984

General Aviation Technology Conference, Hampton, VA, July 10-12, 1984, Technical Papers

The present conference on general aviation aircraft design considers the performance tradeoffs involved in two- and three-control surface aerodynamic configurations, wing design criteria for increased resistance to spins, the performance levels obtained by flight and wind tunnel tests of an 'electroimpulse' deicing system, and the chracteristics of lightning strikes experienced by the NASA F-106B research aircraft. Also considered are the application of speech recognition and synthesis systems to general aviation cockpits, control and display requirements for single-pilot Instrument Flight Rules, pilot interfacing with advanced avionics and automated cockpit systems, the feasibility of sidestick controllers for general aviation aircraft, the acoustic prediction methods incorporated by the NASA Generalized Advanced Propeller Analysis System, and the adhesively bonded structure of the Citation II business jet aircraft.

Source record↗
NASA NTRS1984

Supersonic wing design concepts employing nonlinear flows

Three nonlinear flow concepts for the design of supersonic wings are reviewed. The specific concepts are: leading-edge thrust, supercritical crossflow, and leading-edge vortex flow. The major results of the experimental-theoretical studies supporting the development of these concepts are presented and discussed. Also, supporting aerodynamic prediction methods are described and example applications are given. Recommendations for further development of each concept are made.

Miller, D. S.↗
NASA NTRS1982

Turbine Engine Hot Section Technology (HOST)

Research and plans concerning aircraft gas turbine engine hot section durability problems were discussed. Under the topics of structural analysis, fatigue and fracture, surface protective coatings, combustion, turbine heat transfer, and instrumentation specific points addressed were the thermal and fluid environment around liners, blades, and vanes, material coatings, constitutive behavior, stress-strain response, and life prediction methods for the three components.

Source record↗
NASA NTRS1982

Equivalent damage: A critical assessment

The overall goal of achieving improved life cycle management of aircraft engine, gas turbine components is a major industry thrust. Low cycle fatigue (LCF) crack initiation prediction, an important element of life cycle management as traditionally applied, may be overly conservative in estimating total cyclic life capability. Consequently, there is increasing pressure to improve predictive methods both for crack initiation and for subsequent crack propagation. The utility of equivalent damage concepts for application to hot section components of aircraft engines was studied. Specifically, the topics examined were mean stress, cumulative damage, and multiaxiality. Other factors inherently linked to this study were the basic formulation of damage parameters at elevated temperatures and the fact that hot section components experience severe temperature fluctuations throughout their service lifetime.

Laflen, J. H.↗
NASA NTRS1982

Nonlinear structural and life analyses of a turbine blade

The most critical structural requirements that aircraft gas turbine engines must meet result from the diversity of extreme environmental conditions in the turbine section components. Accurate life assessment of the components under these conditions requires sound analytical tools and techniques. The utility of advanced structural analysis techniques and advanced life prediction techniques in the life assessment of hot-section components was evaluated. The extend to which a three-dimensional cyclic isoparametric finite element analysis of a hot-section component would improve the accuracy of component life predictions was assessed. At the same time, high temperature life prediction theories such as strainrange partitioning and the frequency modified approaches were applied and their efficiency judged. A stress analysis was performed on a commercial air-cooled turbine blade. The evaluation of the life prediction methods indicated that none of those studied were satisfactory.

Kaufman, A.↗
NASA NTRS1982

Life prediction and constitutive behavior: Overview

The evolution of programs to investigate high temperature consititutive behavior and develop cyclic life prediction methods is reviewed. Contracts granted for developing and verifying workable engineering methods for the calculation, in advance of service, of the local stress-strain response at the critical life governing location in typical hot section components as well as the resultant cyclic crack initiation and crack growth lifetimes are listed. The Langley fatigue facility is being upgraded to include: (1) a servocontrolled testing machine for high temperature crack growth; (2) three servocontrolled tension/torsion machines for biaxial studies; (3) a HOST/satellite computer for data acquisition, processing, storage, and retrieval; and (4) HCV/LCF machines for cumulative damage studies.

Halford, G. R.↗
NASA NTRS1984

Creep of chemically vapor deposited SiC fibers

The creep, thermal expansion, and elastic modulus properties for chemically vapor deposited SiC fibers were measured between 1000 and 1500 C. Creep strain was observed to increase logarithmically with time, monotonically with temperature, and linearly with tensile stress up to 600 MPa. The controlling activation energy was 480 + or - 20 kJ/mole. Thermal pretreatments near 1200 and 1450 C were found to significantly reduce fiber creep. These results coupled with creep recovery observations indicate that below 1400 C fiber creep is anelastic with neglible plastic component. This allowed a simple predictive method to be developed for describing fiber total deformation as a function of time, temperature, and stress. Mechanistic analysis of the property data suggests that fiber creep is the result of beta-SiC grain boundary sliding controlled by a small percent of free silicon in the grain boundaries.

Dicarlo, J. A.↗
NASA NTRS1984

Engine cyclic durability by analysis and material testing

The problem of calculating turbine engine component durability is addressed. Nonlinear, finite-element structural analyses, cyclic constitutive behavior models, and an advanced creep-fatigue life prediction method called strainrange partitioning were assessed for their applicability to the solution of durability problems in hot-section components of gas turbine engines. Three different component or subcomponent geometries are examined: a stress concentration in a turbine disk; a louver lip of a half-scale combustor linear; and a squealer tip of a first-stage high-pressure turbine blade. Cyclic structural analyses were performed for all three problems. The computed strain-temperature histories at the critical locations of the combustor linear and turbine blade components were imposed on smooth specimens in uniaxial, strain-controlled, thermomechanical fatigue tests of evaluate the structural and life analysis methods.

Kaufman, A.↗
NASA NTRS1984

Elevated temperature biaxial fatigue

A three year experimental program for studying elevated temperature biaxial fatigue of a nickel based alloy Hastelloy-X has been completed. A new high temperature fatigue test facility with unique capabilities has been developed. Effort was directed toward understanding multiaxial fatigue and correlating the experimental data to the existing theories of fatigue failure. The difficult task of predicting fatigue lives for non-proportional loading was used as an ultimate test for various life prediction methods being considered. The primary means of reaching improved undertanding were through several critical non-proportional loading experiments. It was discovered that the cracking mode switched from primarily cracking on the maximum shear planes at room temperature to cracking on the maximum normal strain planes at 649 C.

Jordan, E. H.↗
NASA NTRS1985

Statement of contamination problem

Space station contamination information is given. There are five major areas in which there are task requirements: (1) potential contaminants need to be identified, i.e., both the sources and types of contaminants, (2) the scope and magnitude of contaminant effects need to be determined, i.e., toxicological effects, microbacteriological effects and impurities, (3) mathematical models for predictive methods need to be developed. (4) state-of-the-art and advanced technologies for monitoring contaminants and for methods of decontamination need to be identified, and (5) automated monitoring and control systems need to be designed.

Hoffler, W.↗
NASA NTRS1984

Review of recent research of interior noise of propeller aircraft

Publications on the topics of propeller source noise, airborne noise transmission, and passenger comfort response to noise and vibration are reviewed. Of the 187 publications referenced, 140 have appeared since 1978. Examples of research accomplishments are presented to illustrate the state of the art. Emphasis is on comparisons of theoretical and measured results, but the description of the theories is left to the references. This review shows that substantial progress has been made in understanding the characteristics of propeller noise, airborne noise, and passenger response, and in the development of prediction methods. Application of the technology to cabin noise control and possible future research directions are discussed.

Mixson, J. S.↗