Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxidative stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Environmental Testing Of High Temperature Materials and Coatings

Materials for today′s extreme environments have unique challenges and design requirements that require multi-faceted evaluations. Thermal and mechanical testing and analysis is important in design, but environmental effects are often the limiting factor of materials in service. Degradation modes such as oxidation, recession, erosion, foreign object damage, and chemical corrosion can negatively impact the materials thermo-mechanical behavior. While materials may ultimately fail under thermo−mechanical stresses, environmental effects are many times the root cause. Evaluation of materials systems under relevant conditions are critical.....start by identifying mechanisms and develop corresponding test methods. Comprehensive modeling begins with thermo-mechanical behavior, then considers environmental degradation modes that provide a “knock down” of that behavior.

Thermal testing Mechanical testing↗
NASA NTRS1982

Elevated temperature properties of aligned ferrous eutectics

Iron base alloys containing aluminum and chromium together with smaller amounts of yttrium and silicon are of interest for high temperature applications. Strengthening an inherently weak but oxidation resistant solid solution matrix with aligned in situ chromium carbides represents an attractive approach to achieving both surface stability and creep resistance at elevated temperatures. Aligned microstructures were produced in alloys of approximately 30 wt % (Cr + Mn), about 3 wt % C and the balance Fe consisting of a gamma matrix and the hexagonal carbide (Cr, Mn, Fe)7C3. The tensile and stress rupture strength to 2000 F of aligned Fe-20 w/t % Cr-10 wt % Mn-3.2 wt % C measured parallel to the carbide reinforcement exceeded those of the strongest iron-nickel superalloys, e.g., CRM-6D developed by Chrysler for automotive turbine application. The cyclic oxidation and sulfidation response of these alloys at elevated temperatures can be markedly improved by aluminum additions.

Lemkey, F. D.↗
DOE OSTI2026

Electrospun Ti–Zr Oxide Heterostructures Enable Strongly Anchored Ultralow-Ir Anodes for Durable Acidic Oxygen Evolution

Proton-exchange-membrane water electrolysis (PEMWE) requires acidic oxygen-evolution-reaction (OER) anodes that combine high activity, high durability, and low Ir loading. Here, we report a Ti-Zr composite electrospun oxide (ESO) nanorod support that enables ultralow-Ir anodes for high-performance PEMWE. Zr-containing Ti oxide heterostructures stabilize anatase-rich TiO2, tune the local oxygen-coordination environment, and strengthen interfacial anchoring of IrOx under acidic anodic conditions. The electrospun nanorod network further creates an open, mechanically coherent catalyst layer that improves Ir utilization, ionomer penetration, and mass transport. At an anode loading of 0.2 mgIr cm-2, the optimized Ir/TiZr20-ESO anode delivers a PEMWE mass activity of 0.99 A mgIr-1 at 1.45 V, 28.3 and 43.0 times higher than commercial Ir black and commercial IrO2/TiO2, respectively. The same anode reaches 3.0 and 4.0 A cm-2 at 1.75 and 1.83 V, respectively, and sustains 2000 h operation at 2.0 A cm-2. Also, accelerated stress tests up to 525 hours over 31,500 cycles confirm promising long-term durability, with an insignificant performance decay of 0.4 μV per cycle. Density functional theory indicates that the Ti-Zr oxide heterostructure suppresses Ti demetallation and strengthens IrO2 interfacial binding, rationalizing the improved high-current-density stability.

25 ENERGY STORAGE↗
NASA NTRS1997

Intracellular pH changes in human aortic smooth muscle cells in response to fluid shear stress

The smooth muscle cell (SMC) layers of human arteries may be exposed to blood flow after endothelium denudation, for example, following balloon angioplasty treatment. These SMCs are also constantly subjected to pressure driven transmural fluid flow. Flow-induced shear stress can alter SMC growth and metabolism. Signal transduction mechanisms involved in these flow effects on SMCs are still poorly understood. In this work, the hypothesis that shear stress alters the intracellular pH (pHi) of SMC is examined. When exposed to venous and arterial levels of shear stress, human aortic smooth muscle cells (hASMC) undergo alkalinization. The alkalinization plateau persisted even after 20 min of cell exposure to flow. Addition of amiloride (10 micromoles) or its 5-(N-ethyl-N-isopropyl) analog (EIPA, 10 micromoles), both Na+/H+ exchanger inhibitors, attenuated intracellular alkalinization, suggesting the involvement of the Na+/H+ exchanger in this response. The same concentrations of these inhibitors did not show an effect on pHi of hASMCs in static culture. 4-Acetamido-4'-isothio-cyanatostilbene-2,2'-disulfonic acid (SITS, 1 mM), a Cl-/HCO3- exchange inhibitor, affected the pHi of hASMCs both in static and flow conditions. Our results suggest that flow may perturb the Na+/H+ exchanger leading to an alkalinization of hASMCs, a different response from the flow-induced acidification seen with endothelial cells at the same levels of shear stress. Understanding the flow-induced signal transduction pathways in the vascular cells is of great importance in the tissue engineering of vascular grafts. In the case of SMCs, the involvement of pHi changes in nitric oxide production and proliferation regulation highlights further the significance of such studies.

NASA Discipline Cell Biology↗
NASA NTRS1966

Weldable aluminum alloy has improved mechanical properties

Weldable aluminum alloy has good resistance to stress-corrosion cracking, shows unchanged strength and formability after storage at room temperature, and can be pre-aged, stretched, and aged. Since toxic fumes of cadmium oxide are evolved when the new alloy is welded, adequate ventilation must be provided.

Westerlund, R. W.↗
NASA NTRS1986

Fracture mechanics

The application of fracture mechanics to the design of ceramic structures will require the precise measurement of crack growth and fracture resistance of these materials over their entire range of anticipated service temperatures and standardized test methods for making such measurements. The development of a standard test for measuring the plane strain fracture toughness is sought. Stress intensity factor coefficients were determined for three varieties of chevron-notch specimens, and fracture toughness measurements were made on silicon nitrides, silicon carbides, and aluminum oxides to assess the performance of each specimen variety. It was determined that silicon nitride and silicon carbides have flat crack growth resistance curves, but aluminum oxide does not. Additionally, batch-to-batch differences were noticed for the aluminum oxide. Experiments are continuing to explain the rising crack growth resistance and batch-to-batch variations for the aluminum oxide.

Shannon, John L., Jr.↗
NASA NTRS1986

Constitutive modelling of single crystal and directionally solidified superalloys

The trend towards improved engine efficiency and durability places increasing demands on materials that operate in the hot section of the gas turbine engine. These demands are being met by new coatings and materials such as single crystal and directionally solidified nickel-base superalloys which have greater creep/fatigue resistance at elevated temperatures and reduced susceptibility to grain boundary creep, corrosion and oxidation than conventionally cast alloys. Work carried out as part of a research program aimed at the development of constitutive equations to describe the elevated temperature stress-strain-time behavior of single crystal and directionally solidified turbine blade superalloys is discussed. The program involves both development of suitable constitutive models and their verification through elevated temperature tension-torsion testing of single crystals of PWA 1480.

Jordan, E. H.↗
DOE OSTI2024

Electrode Elastic Modulus as the Dominant Factor in the Capping Effect in Ferroelectric Hafnium Zirconium Oxide Thin Films

The discovery of ferroelectricity in hafnia based thin films has catalyzed significant research focused on understanding the ferroelectric property origins and means to increase stability of the ferroelectric phase. Prior studies have revealed that biaxial tensile stress via an electrode “capping effect” is a suspected ferroelectric phase stabilization mechanism. This effect is commonly reported to stem from a coefficient of thermal expansion (CTE) incongruency between the hafnia and top electrode. Despite reported correlations between ferroelectric phase fraction and electrode CTE, the thick silicon substrate dominates the mechanics and CTE-related stresses, negating any dominant contribution from an electrode CTE mismatch toward the capping effect. In this work, these discrepancies are reconciled, and the origin of these differences deriving from electrode elastic modulus, not CTE, is demonstrated. Pt/M/TaN/Hf 0.5 Zr 0.5 O 2 /TaN/Si devices, where M is platinum, TaN, iridium, tungsten, and ruthenium, were fabricated. Sin 2 (ψ)-based X-ray diffraction measurements of biaxial stress in the HZO layer reveal a strong correlation between biaxial stress, remanent polarization, and electrode elastic modulus. Conversely, a low correlation exists between the electrode CTE, HZO biaxial stress, and remanent polarization. A higher elastic modulus enhances the resistance to electrode elastic deformation, which intensifies the capping effect during crystallization, and culminates in the tandem restriction of out-of-plane hafnia volume expansion and preferential orientation of the polar c-axis normal to the plane. These behaviors concomitantly increase the ferroelectric phase stability and polarization magnitude. This work provides electrode material selection guidelines toward the development of high-performing ferroelectric hafnia into microelectronic devices, such as nonvolatile memories.

36 MATERIALS SCIENCE↗
NASA NTRS1999

Intermediate Temperature Stress Rupture of a Woven Hi-Nicalon, BN-Interphase, SiC Matric Composite in Air

Woven Hi-Nicalon (TM) reinforced melt-infiltrated SiC matrix composites were tested under tensile stress-rupture conditions in air at intermediate temperatures. A comprehensive examination of the damage state and the fiber properties at failure was performed. Modal acoustic emission analysis was used to monitor damage during the experiment. Extensive microscopy of the composite fracture surfaces and the individual fiber fracture surfaces was used to determine the mechanisms leading to ultimate failure. The rupture properties of these composites were significantly worse than expected compared to the fiber properties under similar conditions. This was due to the oxidation of the BN interphase. Oxidation occurred through the matrix cracks that intersected the surface or edge of a tensile bar. These oxidation reactions resulted in minor degradation to fiber strength and strong bonding of the fibers to one another at regions of near fiber-to-fiber contact. It was found that two regimes for rupture exist for this material: a high stress regime where rupture occurs at a fast rate and a low stress regime where rupture occurs at a slower rate. For the high stress regime, the matrix damage state consisted of through thickness cracks. The average fracture strength of fibers that were pulled-out (the final fibers to break before ultimate failure) was controlled by the slow-crack growth rupture criterion in the literature for individual Hi-Nicalon (TM) fibers. For the low stress regime, the matrix damage state consisted of microcracks which grew during the rupture test. The average fracture strength of fibers that were pulled-out in this regime was the same as the average fracture strength of individual fibers pulled out in as-produced composites tested at room temperature.

Morscher, Gregory N.↗
NASA NTRS1992

Observation of radiation induced changes in stress and electrical properties in MOS devices

Strain measurements using X-ray diffraction were performed on irradiated commercial and radiation-hardened metal gate CMOS devices in addition to polysilicon gate NMOS devices. I-V curves were taken and V(ot) and V(it) were separated using the subthreshold slope method for all devices. A correlation has been shown to exist between physical strain relaxation and the electrical properties as a function of radiation dose and recovery. Data shown suggest that the physical response (strain relaxation) in the silicon at the oxide interface is a measure of the type of damage induced and the recovery mechanism. Postradiation measurements of Delta V(it) and Delta V(ot) taken immediately after irradiation support the conclusions of V. Zekeriya and T.-P. Ma (1983) and K. Kasama et al. (1986, 1987); compressive stress at the silicon/SiO2 interface does reduce radiation damage in the device.

Shaw, D. C.↗
NASA NTRS2018

Coupled Thermomechanical Micromechanics Modeling of the Influence of Thermally Grown Oxide Layer in an Environmental Barrier Coating System

Environmental Barrier Coatings (EBCs) have emerged as a promising means of protecting critical components for high temperature applications (e.g., aircraft engines). EBCs are often used to protect an underlying material (substrate) from extreme thermal/chemical environments. However, systems that utilize EBCs are susceptible to a number of failure modes including oxidation/delamination. Environmental Barrier Coatings (EBCs) have emerged as a promising means of protecting silicon based ceramic matrix composite (CMC) components for high temperature applications (e.g., aircraft engines). EBCs are often used to protect an underlying material (substrate) such as silicon carbide from extreme thermal/chemical environments. In a typical CMC/EBC system, an EBC may or may not be adhered to an underlying substrate with a bond coat (e.g., silicon). Irrespective, systems that utilize EBCs are susceptible to a number of failure modes including oxidation/delamination, recession, chemical attack and dissolution, thermo-mechanical degradation, erosion, and foreign object damage. Current work at NASA Glenn Research Center is aimed at addressing these failure modes in EBC systems and developing robust analysis tools to aid in the design process. The Higher-Order Theory for Functionally Graded Materials (HOTFGM), a precursor to the High-Fidelity Generalized Method of Cells micromechanics approach, was developed to investigate the coupled thermo-mechanical behavior of functionally graded composites and will be used herein to assess the development and growth of a low-stiffness thermally grown oxide (TGO) layer in EBC/CMC systems without a silicon bond coat. To accomplish this a sensitivity study is conducted to examine the influence of uniformly and non-uniformly grown oxide layer on the associated driving forces leading to mechanical failure (spallation) of EBC layer when subjected to isothermal loading, recession, chemical attack and dissolution, thermomechanical degradation, erosion, and foreign object damage. Current work at NASA Glenn Research Center is aimed at addressing these failure modes in EBC systems and developing robust analysis tools to aid in the design process. The Higher-Order Theory for Functionally Graded Materials (HOTFGM), a precursor to the High-Fidelity Generalized Method of Cells micromechanics approach, was developed to investigate the coupled thermo-mechanical behavior of functionally graded composites (Aboudi et al., 1999, Composites B). For example, HOTFGM was previously used (Arnold et al, 1995, NASA CP 10178, paper 34), to assess interlaminar stresses (including free edge effects) in a substrate with a thermal barrier coating (TBC). In this study, HOTFGM micromechanics analyses will be used to assess the development and growth of a low-stiffness thermally grown oxide (TGO) layer between a silicon carbide substrate and a ytterbium disilicate EBC. In order to realistically simulate TGO growth, an evolution law will be incorporated into HOTFGM. In addition, the effect of TGO roughness will be explored consistent with previous TBC work (Pindera et al., 2000. Material Science and Engineering, A284, pp. 158-175). This model represents a first step in developing a robust analysis tool that can ultimately be used to design durable EBC systems. Additional failure modes will be considered as part of a future work.

environmental barrier coating↗
NASA NTRS2018

Importance of Measuring SiC Fiber Diameter Prior to Conducting Fiber Stress Rupture / Creep Tests?

A very significant amount of SiC fiber creep / stress rupture data has been generated and reported in the past by various researchers. Due to the difficulty of measuring fiber diameter and the amount of time required to make accurate measurements, researchers have quite often used an accepted average diameter value (which is fiber type-dependent) when determining the load that will be applied to a fiber to generate a specific stress during testing. Of course, this approach has less of an effect on data scatter when the individual fibers in a tow have very similar diameters (minimal fiber-to-fiber variation in diameter). NASA GRC has begun using a laser fiber diameter measurement system, and we are considering eventually characterizing each SiC fiber prior to testing in creep/stressed oxidation. The laser system will be described in this presentation, as well as examples of fiber diameter data obtained in the past at AFRL. We are currently discussing the merits of using an average diameter in testing/data analysis vs. using a measured or "known" diameter. Information about our current intermediate temperature SiC fiber stress rupture testing will also be provided.

ceramic matrix composites↗
DOE OSTI2022

Coral and Seawater Metagenomes Reveal Key Microbial Functions to Coral Health and Ecosystem Functioning Shaped at Reef Scale

The coral holobiont is comprised of a highly diverse microbial community that provides key services to corals such as protection against pathogens and nutrient cycling. The coral surface mucus layer (SML) microbiome is very sensitive to external changes, as it constitutes the direct interface between the coral host and the environment. Here, we investigate whether the bacterial taxonomic and functional profiles in the coral SML are shaped by the local reef zone and explore their role in coral health and ecosystem functioning. The analysis was conducted using metagenomes and metagenome-assembled genomes (MAGs) associated with the coral Pseudodiploria strigosa and the water column from two naturally distinct reef environments in Bermuda: inner patch reefs exposed to a fluctuating thermal regime and the more stable outer reefs. The microbial community structure in the coral SML varied according to the local environment, both at taxonomic and functional levels. The coral SML microbiome from inner reefs provides more gene functions that are involved in nutrient cycling (e.g., photosynthesis, phosphorus metabolism, sulfur assimilation) and those that are related to higher levels of microbial activity, competition, and stress response. In contrast, the coral SML microbiome from outer reefs contained genes indicative of a carbohydrate-rich mucus composition found in corals exposed to less stressful temperatures and showed high proportions of microbial gene functions that play a potential role in coral disease, such as degradation of lignin-derived compounds and sulfur oxidation. The fluctuating environment in the inner patch reefs of Bermuda could be driving a more beneficial coral SML microbiome, potentially increasing holobiont resilience to environmental changes and disease.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Diagnosis of PV Cell Passivation Degradation Resulting from Hot-Humid, High Voltage Potential Aging

Corrosion of the antireflective coating on the cell ("AR c corrosion") was previously observed in studies using hot-humid test conditions with external high voltage (HV) bias. Because AR c corrosion is not well understood, mini-modules (MiMos) were examined in a comparative experiment using PERC and PERT as well as legacy Al-BSF cells. For separate MiMos with the cell circuit electrical at +1500 V, -1500 V, or unbiased "V oc", test conditions in the comparative study included 60degrees C/60% RH for 96 h, as in IEC TS 62804-1; 70degrees C/70%RH for 200 h; and 85degrees C/85% RH for 200 h. Characterizations at each read point included: camera and electroluminescence (EL) imaging, colorimetry, and I-V curve tracing. Characterizations at the final read point included: SunsVoc; spatially mapping external quantum efficiency (EQE); high resolution: photoluminescence (PL), EL, and dark lock-in thermographic (DLIT) imaging. Forensics were performed on extracted cores, including scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS) and scanning Auger microscopy (SAM). Forensics were also conducted on MiMos (stepped HV aging) and full-sized modules (outdoor aging) from previous studies. AR c corrosion was specifically observed for the glass/encapsulant/cell side of +1500 V (HV+) stressed MiMos, where appearance, color, and reflectance were the characteristics most distinguished relative to simultaneously occurring degradation modes. SEM/EDS and SAM identified conversion of silicon nitride to silicon oxide or hydrous silica, preferentially occurring at the edges and tips of the pyramidal textured cell surface.

aging↗
DOE OSTI2022

Fabrication and Irradiation Behavior of Thulium Sesquioxide

The results of reactor irradiation of thulium sesquioxide are discussed, along with chemical and physical properties and wafer fabrication. Sintered densities up to 90% of theoretical were obtained in target wafers using oxide reprocessed to obtain readily sinterable powder. Irradiation to about 1.8 w/g did not change the microstructure of the wafers although some wafers broke, probably because of mechanical stresses in target and disassembly.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Alloy design with oxide dispersoids and precipitates

The mechanical behavior of particle-strengthened alloys is reviewed. On the basis of this knowledge, it is concluded that second-phase particles, coherent or incoherent, can enhance the flow strength, creep resistance, and stress-rupture life of alloys. Unfortunately, particles are usually not beneficial alloy-design elements if enhanced uniaxial ductility, plane-strain ductility, stress-rupture ductility, and toughness are called for. Such properties as fatigue-crack propagation resistance appear to require, for example, both high strength and high ductility, a situation which can come to pass only when the perennial conflict between strength and ductility is resolved in particle-strengthened systems in particular and in any other material system in general. Wherever possible, the role of coherent and incoherent particles in alloy design is distinguished.

Tien, J. K.↗
NASA NTRS1985

Slow plastic strain rate compressive flow in binary CoAl intermetallics

Constant-velocity elevated temperature compression tests have been conducted on a series of binary CoAl intermetallics produced by hot extrusion of blended prealloyed powders. The as-extruded materials were polycrystalline, and they retained their nominal 10-micron grain size after being tested between 1100 and 1400 K at strain rates ranging from 2 x 10 to the -4th to 2 x 10 to the -7th per sec. Significant plastic flow was obtained in all cases; while cracking was observed, much of this could be due to failure at matrix-oxide interfaces along extrusion stringers rather than to solely intergranular fracture. A maximum in flow strength occurs at an aluminum-to-cobalt ratio of 0.975, and the stress exponent appears to be constant for aluminum-to-cobalt ratios of 0.85 or more. It is likely that very aluminum-deficient materials deform by a different mechanism than do other compositions.

Whittenberger, J. D.↗
NASA NTRS1989

Identification of a cast iron alloy containing nonstrategic elements

A program was performed to address the mechanical and environmental needs of Stirling engine heater head and regenerator housing components, while reducing the dependence on strategic materials. An alloy was developed which contained no strategic elemental additions per se. The base is iron with additions of manganese, molybdenum, carbon, silicon, niobium, and ferro-chromium. Such an alloy should be producible on a large scale at very low cost. The resulting alloy, designated as NASAUT 4G-Al, contained 15 Mn, 15 Cr, 2 Mo, 1.5 C, 1.0 Si, 1.0 Nb (in weight percent) with a balance of Fe. This alloy was optimized for chemistry, based upon tensile strength, creep-rupture strength, fracture behavior, and fatigue resistance up to 800 C. Alloys were also tested for environmental compatibility. The microstructure and mechanic properties (including hardness) were assessed in the as-cast condition and following several heat treatments, including one designed to simulate a required braze cycle. The alloy was fabricated and characterized in the form of both equiaxed and columnar-grained castings. The columnar grains were produced by directional solidification, and the properties were characterized in both the longitudinal and transverse orientations. The NASAUT 4G-Al alloy was found to be good in cyclic-oxidation resistance and excellent in both hydrogen and hot-corrosion resistance, especially in comparison to the baseline XF-818 alloy. The mechanical properties of yield strength, stress-rupture life, high-cycle-fatigue resistance, and low-cycle-fatigue resistance were good to excellent in comparison to the current alloy for this application, HS-31 (X-40), with precise results depending in a complex manner on grain orientation and temperature. If required, the ductility could be improved by lowering the carbon content.

Cooper, C. V.↗