Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “neutral beam”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

On Ba(+) production in the CRIT 2 experiment

Analysis of partical data from the CRIT 2 experiment, studying Alfven's critical ionization velocity (CIV) effect, shows that the density of newly created ions (presumably Ba(+) from the shaped-charge beam) is consistent with the increase in total plasma density measured by the independent RF plasma probe on board (Swenson et al., 1990) at the most active time period. We model this ion production using the measured electron flux data and the neutral barium model of Stenbaek-Nielsen et al. (1990a). To identify the main source mechanisms which may contribute most to the barium ionization, a simple model for the barium ion density at the payload location is developed based on Liouvilles theorem. We estimate that the electron impact ionization is responsible for 90% of the barium ion production observed by CRIT 2 in the first release and up to 45% in the second release. By employing a two-state approximation calculation (Rapp and Francis, 1962), the Ba-O(+) charge exchange cross section is found to range from about 2.0 X 10(exp -17) sq cm at a velocity of 4 km/s to 2.0 X 10(exp -15) sq cm at a velocity of 20 km/s. This result suggests that the Ba-O(+) charge exchange is probably dominant among all the non-CIV ionization processes. By considering the charge exchange process in our density model, the barrium ion densities are calculated for the two releases on CRIT II. The comparison between the model results and the observed data is found to be resonably consistent if the cross sections, as calculated above, are multiplied by 0.3 for the first release and 1.0 for the second release. Our result suggests that the charge exchange process could be the most important non-CIV ionization mechanism in the CRIT II experiment and it should be considered carefully case by case in CIV experiments.

Liou, K.↗
DOE OSTI2026

First Sterile Neutrino Search at NOvA Experiment Using both Neutrino and Anti-Neutrino Data

Neutrinos are among the most abundant fundamental particles in the universe, and yet they are so elusive that they pass through almost everything without leaving a trace. For decades, researchers have measured neutrino oscillations in great detail, refining our understanding of the theories. Yet, once again, neutrino shows their incredibly surprising nature through some recent experimental results, suggesting that our current understanding might be incomplete. Several experiments have observed an unexpected difference in the observed neutrino behaviour from what the Standard Model predicts, showing an excess in some cases (e.g. LSND, MiniBooNE) and a deficit of neutrino events in others (e.g. SAGE, GALLEX). These anomalies challenge our conventional theories of standard three neutrino flavors and phenomenologically motivate the sterile neutrino hypothesis, which does not interact through the usual weak force. While some results appear consistent with this idea, others have found no supporting evidence (e.g. MicroBooNE), leaving the question unanswered. NOvA is one such long-baseline neutrino experiment with its Near Detector (ND) at Fermilab and a Far Detector (FD) at 810 km in Minnesota. It uses the NuMI beam as its primary source of neutrinos for oscillation studies. Its two-detector setup, extended baseline, and ability to conduct combined $\nu$-$\bar\nu$ analyses position it to explore these phenomena in new ways. We use the joint $\nu_{\mu}$ and neutral current (NC) disappearance channels to probe active-sterile mixing in the 3+1 model. This analysis utilizes a data sample of 27$\times$10$^{20}$ protons on target (POT) in neutrino mode and 12.5$\times$10$^{20}$ protons on target (POT) in antineutrino mode. We found no evidence of sterile neutrino at 90$\%$ C.L. We present the limits in $\sin^{2}\theta_{24}$ vs $\Delta m^{2}_{41}$, $\sin^{2}\theta_{34}$ vs $\Delta m^{2}_{41}$, and $\sin^{2}2\theta_{\mu\tau}$ vs $\Delta m^{2}_{41}$ parameter spaces. The limits provided by this analysis are world leading in most of the parameter spaces.

Chaudhary, Shivam [Indian Inst. of Info. Tech. Guw↗
NASA NTRS1974

Observations of radiation from an electron beam artificially injected into the ionosphere

This paper reports the observations of waves generated by a controlled beam of particles artificially injected into the ionosphere and magnetosphere. The measurements were made during the Electron Echo 1 experiment, in which an electron accelerator was carried to a height of 350 km in the ionosphere from Wallops Island, Virginia, on an Aerobee 350 sounding rocket. It injected into the earth's magnetic field over 3000 16-ms pulses of electrons with 40-keV energy and a current of 70 mA at pitch angles between 70 and 110 deg. The ejected fiber glass nose cone carried antennas and receivers to measure the electric field of waves generated by the beam. Associated with the electron beam was radiation detected at frequencies near the electron plasma frequency of the background ionosphere, near twice the electron cyclotron frequency in the whistler mode, and near zero frequency. Associated with the operation of an argon plasma generator used to keep the accelerator neutralized were continuous emissions detected at frequencies near the lower-hybrid resonance (LHR).

Cartwright, D. G.↗
NASA NTRS1977

A hollow cathode hydrogen ion source

High current density ion sources have been used to heat plasmas in controlled thermonuclear reaction experiments. High beam currents imply relatively high emission currents from cathodes which have generally taken the form of tungsten filaments. A hydrogen ion source is described which was primarily developed to assess the emission current capability and design requirements for hollow cathodes for application in neutral injection devices. The hydrogen source produced ions by electron bombardment via a single hollow cathode. Source design followed mercury ion thruster technology, using a weak magnetic field to enhance ionization efficiency.

Sovey, J. S.↗
NASA NTRS1983

SADE: A space experiment to demonstrate structural assembly

The Structural Assembly and Demonstration Experiment (SADE) demonstrates that the Shuttle is a suitable base for space construction; this includes a test of the Shuttle's control system to determine its performance when a long attached truss or beam is extended from the bay. Examples of Shuttle-related systems that will receive special attention are the RMS, the lighting system, and the crew assembly capabilities. A second purpose is to determine the extent to which the assembly results from the Neutral Buoyancy Simulator can be used to forecast the results of space assembly is determined. Finally, the SADE truss design will be validated by measuring the performance of the deployment, the special connectors, and the assembly methods.

Harrison, J. K.↗
NASA NTRS1990

NGC 1058: Gas motions in an extended, quiescent spiral disk

Researchers investigate in detail the motion of gas in the galaxy NGC 1058 using the very large array (VLA) to map the emission in the 21-cm line. This galaxy is so nearly face-on that the contribution to the line width due to the variation of the rotational velocity across the D-array beam is small compared with the random z-motion of the gas. Researchers confirm results of earlier studies (Lewis 1987, A. and A. Suppl., 63, 515; van der Kruit and Shostak 1984, A. and A., 134, 258) of the galaxy's total neutral hydrogen (HI) and kinematics, including the fact that the rotation curve drops faster than Keplerian at the outer edge of the disk, which is interpreted as a fortuitous twist of the plane of rotation in the outer disk. However, their very high velocity resolution (2.58 km s(exp -1) after Hanning smoothing) coupled with good spatial resolution, allows researchers to measure more accurately the line width, and even to some extent its shape, throughout the disk. One of the most interesting results of this study is the remarkable constancy of the line width in the outer disk. From radius 90 to 210 seconds the Gaussian velocity dispersion (sigma sub nu) of the 21-cm line has a mean value of 5.7 km s(exp -1) (after correcting for the spectral resolution) with a dispersion of less than 0.9 km s(exp -1) (after correcting for the spectral resolution) with a dispersion of less than 0.9 km s(exp -1). Translating this directly into a kinetic temperature (Doppler temperature): T sub Dopp equals 121K (sigma sub mu exp 2/(km s(exp -1) (exp 2) gives 4000 K, with a dispersion of less than 1500 K over the outer disk. This constancy is observed even when comparing the spiral arms versus inter-arm regions, which in the radius range from 100 to 150 seconds the surface density modulates (defined as the ratio N sub peak -N sub trough/N sub peak + N sub trough) from 0.5 to 0.25 in the range 150 to 200 seconds.

Hanson, Margaret Murray↗
DOE OSTI2022

Neutrino interaction measurements with the MicroBooNE and ArgoNeuT liquid argon time projection chambers

Abstract Precise modeling of neutrino interactions on argon is crucial for the success of future experiments such as the Deep Underground Neutrino Experiment (DUNE) and the Short-Baseline Neutrino (SBN) program, which will use liquid argon time projection chamber (LArTPC) technology. Argon is a large nucleus, and nuclear effects—both on the initial and final-state particles in the interaction—are expected to be large in neutrino–argon interactions. Therefore, measurements of neutrino scattering cross sections on argon will be of particular importance to future DUNE and SBN oscillation measurements. This article presents a review of neutrino–argon interaction measurements from the MicroBooNE and ArgoNeuT collaborations, using two LArTPC detectors that have collected data in the NuMI and Booster Neutrino Beams at Fermilab. Measurements are presented of charged-current muon neutrino scattering in the inclusive channel, the ‘0 $$\pi $$ π ’ channel (in which no pions but some number of protons may be produced), and single pion production (including production of both charged and neutral pions). Measurements of electron neutrino scattering are presented in the form of $$\nu _e+\bar{\nu }_e$$ ν e + ν ¯ e inclusive scattering cross sections.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1985

Wave-particle interactions induced by SEPAC on Spacelab 1 Wave observations

Space experiments with particle accelerators (SEPAC) flew on Spacelab 1 in November and December 1983. SEPAC included an accelerator which emitted electrons into the ionospheric plasma with energies up to 5 keV and currents up to 300 mA. The SEPAC equipment also included an energetic plasma generator, a neutral gas generator, and an extensive array of diagnostics. The diagnostics included plasma wave detectors, and energetic electron analyzer, a photometer, a high sensitivity television camera, a Langmuir probe and a pressure gage. Twenty-eight experiments were performed during the mission to investigate beam-plasma interactions, electron beam dynamics, plasma beam propagation, and vehicle charging. The wave-particle interactions were monitored by the plasma wave instrumentation, by the energetic electron detector and by the optical detectors. All show evidence of wave-particle interactions, which are described in this paper.

Taylor, W. W. L.↗
NASA NTRS1942

Beam and Torsion Tests of Aluminum-alloy 61S-T Tubing

Tests were made to determine the effect of length and the effect of ratios of diameter to wall thickness upon the flexural and torsional moduli of failure of 61S-T aluminum-alloy tubing. The moduli of failure in bending, as determined by tests in which the tubing was loaded on the neutral axis at the one-third points of the span, were found to bear an approximately linear relationship with diameter-thickness ratio and were practically independent of span within the limits investigated. Empirical equations are given describing the relations obtained. The moduli of failure in torsion were found to be dependent upon length as well as upon diameter-thickness ratios. Empirical equations are given for predicting strengths within the range of plastic buckling. Within the elastic range, available torsion theories were found to be satisfactory.

Moore, R L↗
DOE OSTI2026

Inclusive Search for Anomalous Single-Photon Production in MicroBooNE

We present an inclusive search for anomalous production of single-photon events from neutrino interactions in the MicroBooNE experiment. The search and its signal definition are motivated by the previous observation of a low-energy excess of electromagnetic shower events from the MiniBooNE experiment. We use the Wire-Cell reconstruction framework to select a sample of inclusive single-photon final-state interactions with a final efficiency and purity of 7.0% and 40.2%, respectively. We leverage simultaneous measurements of sidebands of charged current 𝜈 𝜇 interactions and neutral current interactions producing 𝜋 0 mesons to constrain signal and background predictions and reduce uncertainties. We perform a blind analysis using a dataset collected from February 2016 to July 2018, corresponding to an exposure of 6.34 × 10 20 protons on target from the Booster Neutrino Beam at Fermilab. In the full signal region, we observe agreement between the data and the prediction, with a goodness-of-fit 𝑝 value of 0.11. We then isolate a subsample of these events containing no visible protons, and observe 93 ± 22⁢(stat) ±35⁢(syst) data events above prediction, corresponding to just above 2⁢𝜎 local significance, concentrated at shower energies below 600 MeV.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

The JLab Eta Factory (JEF) experiment

The new experiment, JLab Eta Factory (JEF), in the experimental Hall D at Jefferson Lab will extend the physics potential of the GlueX detector beyond the main spectroscopy program and perform precision measurements of various ?(?)decays with emphasis on rare neutral modes. The physics program of the experiment spans from precision tests of low-energy QCD to search of gauge bosons in the mass range below 1 GeV coupling the SM sector to the dark sector. Photoproduction of highly boosted ?(?)mesons using a tagged photon beam, good detection of recoil proton and multi-photon final states will allow to suppress background and collect high-statistics data sample of ?mesons. All these provide many advantages over other ?(?)experiments. The JEF experiment requires to upgrade the inner part of the forward lead glass calorimeter of the GlueX detector with high-granularity, high-resolution lead tungstate PbWO4 scintillating crystals. The calorimeter insert is currently under construction at Jeffeson Lab. The detector will be ready to take data in 2024. An overview of the JEF project will be presented.

Somov, Alexander↗
NASA NTRS1989

Electron/Ion-Scattering Apparatus

In new apparatus, most of electrons scattered inelastically over wide range of angles measured simultaneously, with consequent increase in signal-to-noise ratio by factor of about 10 to 4th power. Beam of electrons and beam of ions aimed along low-intensity magnetic field between pair of electric-field plates. Crossed electric and magnetic fields hardly affect ions but cause electrons to drift toward ions by trochoidal motion. With modifications, apparatus used for measurements of excitation cross sections in neutral atoms, molecules, radicals, and excited states of atoms and molecules.

Chutjian, Ara↗
NASA NTRS2010

Designs and Materials for Better Coronagraph Occulting Masks

New designs, and materials appropriate for such designs, are under investigation in an effort to develop coronagraph occulting masks having broad-band spectral characteristics superior to those currently employed. These designs and materials are applicable to all coronagraphs, both ground-based and spaceborne. This effort also offers potential benefits for the development of other optical masks and filters that are required (1) for precisely tailored spatial transmission profiles, (2) to be characterized by optical-density neutrality and phase neutrality (that is, to be characterized by constant optical density and constant phase over broad wavelength ranges), and/or (3) not to exhibit optical- density-dependent phase shifts. The need for this effort arises for the following reasons: Coronagraph occulting masks are required to impose, on beams of light transmitted through them, extremely precise control of amplitude and phase according to carefully designed transmission profiles. In the original application that gave rise to this effort, the concern has been to develop broad-band occulting masks for NASA s Terrestrial Planet Finder coronagraph. Until now, experimental samples of these masks have been made from high-energy-beam-sensitive (HEBS) glass, which becomes locally dark where irradiated with a high-energy electron beam, the amount of darkening depending on the electron-beam energy and dose. Precise mask profiles have been written on HEBS glass blanks by use of electron beams, and the masks have performed satisfactorily in monochromatic light. However, the optical-density and phase profiles of the HEBS masks vary significantly with wavelength; consequently, the HEBS masks perform unsatisfactorily in broad-band light. The key properties of materials to be used in coronagraph occulting masks are their extinction coefficients, their indices of refraction, and the variations of these parameters with wavelength. The effort thus far has included theoretical predictions of performances of masks that would be made from alternative materials chosen because the wavelength dependences of their extinction coefficients and their indices of refraction are such that that the optical-density and phase profiles of masks made from these materials can be expected to vary much less with wavelength than do those of masks made from HEBS glass. The alternative materials considered thus far include some elemental metals such as Pt and Ni, metal alloys such as Inconel, metal nitrides such as TiN, and dielectrics such as SiO2. A mask as now envisioned would include thin metal and dielectric films having stepped or smoothly varying thicknesses (see figure). The thicknesses would be chosen, taking account of the indices of refraction and extinction coefficients, to obtain an acceptably close approximation of the desired spatial transmittance profile with a flat phase profile

Balasubramanian, Kunjithapatham↗
NASA NTRS2011

Regarding the Possible Generation of a Lunar Nightside Exo-Ionosphere

The non-condensing neutral helium exosphere is at its most concentrated levels on the cold lunar nightside. We show herein that these He atoms are susceptible to impact ionization from primary and secondary electrons flowing in the vicinity of the negatively-charged nightside lunar surface. The secondary electron beams are a relatively recent discovery and are found to be emitted from the nightside surface at energies consistent with the negative surface potential. The effect is to create an electron impact-created ionosphere in nightside regions. possibly especially potent within polar craters.

Farrell, W. M.↗
NASA NTRS2013

Towed Subsurface Optical Communications Buoy

The innovation allows critical, high-bandwidth submarine communications at speed and depth. This reported innovation is a subsurface optical communications buoy, with active neutral buoyancy and streamlined flow surface veins for depth control. This novel subsurface positioning for the towed communications buoy enables substantial reduction in water-absorption and increased optical transmission by eliminating the intervening water absorption and dispersion, as well as by reducing or eliminating the beam spread and the pulse spreading that is associated with submarine-launched optical beams.

Stirbl, Robert C.↗
DOE OSTI2023

Measurement of the pion charge exchange differential cross section on Argon with the ProtoDUNE-SP detector

The Deep Underground Neutrino Experiment (DUNE) utilizes Liquid Argon Time Projection Chamber (LArTPC) technology in its pursuit of uncovering the origins of matter. As a crucial prototype for the DUNE far detector (FD) module, ProtoDUNE-SP at CERN Neutrino Platform Facility employs a hadron test beam with a momentum range of 0.3 to 7 GeV/c to study the detector response to particles that could be produced in the neutrino interactions at the DUNE FD. Furthermore, ProtoDUNE-SP is dedicated to testing event reconstruction and performing detector calibration under controlled conditions. Neutral pion reconstruction performance is an important benchmark of the calorimetric and tracking capability of LArTPC, and understanding neutral pion in LArTPC is crucial to characterize backgrounds to oscillation measurements and rare searches. To improve neutral pion reconstruction in LArTPC, a kinematic fitting algorithm is developed, achieving a 12% resolution in neutral pion energy in ProtoDUNE-SP. This enhancement enables the first measurements of the pion-argon charge exchange differential cross-section. By comparing these results with the current model, valuable constraints can be made to improve generator simulations in the future DUNE experiment.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Thermal energy transport in laser-driven high x-ray conversion efficiency metallic silver nanowire foams

Here, we report on record brightness from Ag x-ray emission obtained using a novel laser-produced plasma source. The reported K-shell conversion efficiency of nearly 1% with a radiant energy of ≈ 0.6 kJ/sr from Ag ions is the highest presently recorded and is about twofold greater than more conventional metal-lined cavity targets. He-like Ag ions are the dominant radiators at ≈ 22.7 keV, which contrast the x-ray sources from other pulse power facilities that produce K-shell x-rays from Auger processes in near-neutral ions driven by the nonthermal hot electrons produced in the Z-pinch implosion. The reported x-ray emission was produced from a 4-mm-diameter, 4-mm-long underdense silver nanowire target at 10⁢ mg/⁢cm 3 . The National Ignition Facility laser beams deposited ≈ 1000 kJ of 3ω light into the target with a ≈ 400 TW, 2.5 ns square pulse. Finally, we show via comparisons of data with radiation-hydrodynamics simulations that flux-limited classical thermal energy transport models are inadequate in correctly modeling the behavior of these non-local thermodynamic equilibrium plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1973

Performance of a 15 cm ion thruster with reliable restart capability

Experimental evaluation of a modified SERT II thruster with dished grids capable of producing a 600 ma ion beam at 2690 sec specific impulse and achieving rapid, reliable startup is described. In addition to steady-state performance curves, thruster performance is examined over the duration of rapid startup and one hour operating sequence. Rapid startup utilizing high voltage spark ignition of the main and neutralizer cathodes is described. Minimal deterioration of the cathodes and the ignition system during 1000 neutralizer cathode startups and 2000 main cathode startups is demonstrated. The need for heaters and a vaporizer control system to facilitate more rapid startup is identified.

Wilbur, P. J.↗