Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material science”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Optimization of boron carbide density using direct current sintering for use as sputtering sources at the National Ignition Facility

Several experimental trials were conducted to determine optimal sintering parameters and compositions for purchased boron carbide powder using spark plasma sintering/direct current sintering. Sputtering targets used to create ablators for the National Ignition Facility have been unable to survive post processing procedures suggesting that in-house fabrication may yield better results due to extended control.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Understanding spectral dependance of laser-induced damage precursors in dielectric materials (Full report_23-ERD-006)

The performance of high-energy laser systems is constrained by laser-induced damage in dielectric coatings, particularly those containing hafnium oxide (HfO 2 ). While thresholds at fundamental Nd harmonics are well studied, the spectral dependence of damage initiation—especially under dual-wavelength irradiation—remains poorly characterized. This project provides the first systematic investigation of wavelength-dependent laser damage in hafnia coatings, focusing on nanoscale precursors such as craze lines, nanobubbles, stoichiometric variations, nodules, and controlled crystallization. Coatings were fabricated via ion beam sputtering and electron-beam deposition and characterized using spectrophotometry, ellipsometry, AFM, GI-XRD, RBS, PCI absorption, and fs/ns laser damage testing. Results show that craze lines, benign under infrared light, strongly initiate damage under UV due to wavelength-selective field intensification. Substituting xenon for argon suppresses nanobubbles and improves UV thresholds by up to 32%. Oxygen modulation reveals that fully oxidized films maximize UV resistance, though at the cost of porosity and stress in multilayers. HfO 2 –SiO 2 composites resist crystallization and defects while achieving ppm-level absorption and elevated thresholds, whereas full crystallization of HfO 2 enhances LIDT by reducing defects and improving thermal transport. Collectively, these findings link photon energy, defect states, and bandgap collapse, providing a predictive framework for wavelength-dependent laser damage. The outcomes directly inform the design of durable, multi-wavelength coatings for facilities such as NIF, MEC, HAPLS, and DPAL, advancing the readiness of next-generation optics.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Quantitative measurements of dislocations in metals for advancing predictive simulations

LLNL applications require scientists to predict how materials evolve under various thermomechanical conditions. While this is achieved through physics-based simulations, uncertainty in the predictions of mechanical properties remains a serious challenge that limits the predictive capabilities of models because we lack methods to compare predictions of atomic-scale defects (dislocations) with experimental measurements. High energy X-ray diffraction (HEXRD) is the most relevant technique that can provide the necessary statistical information on dislocations. However, this technique is not yet quantitative because we lack a precise understanding of the relationship between X-ray diffraction patterns and the underlying material dislocation content and arrangements. To address this need, we used our novel computational X-ray diffraction method to simulate the effect of dislocations on the diffraction patterns. We compared virtual and experimental diffraction patterns. Results allowed us to clearly establish the relationship between X-ray diffraction patterns and the underlying dislocation structures, proving that it is feasible to quantitatively measure dislocation statistics with HEXRD. This project delivered a method that can provide the missing piece to LLNL’s mechanical property simulations in advanced metals by obtaining experimentally long-needed quantitative dislocation data, which could fully enable predictive capabilities.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Soliton Generation in Negative Thermal Expansion Materials

Strain solitons have been observed statically in several 2D materials and dynamically in substrate materials using ultrafast laser pulses. The latter case relies on lattice relaxation in response to ultrafast heating in a light-absorbing transducer material, a process which is sensitive to the thermal expansion coefficient. Here we consider an unusual case where the sign of the thermal expansion coefficient is negative, a scenario which is experimentally feasible in light of rapid and recent advances in the discovery of negative thermal expansion materials. We present numerical solutions to a nonlinear differential equation which has been repeatedly demonstrated to quantitatively model experimental data and discuss the salient results using realistic parameters for material linear and nonlinear elasticity. The solitons that emerge from the initial value problem with negative and positive thermal expansion are qualitatively different in several ways. The new case of negative thermal expansion gives rise to a nearly-periodic soliton train with chirped profile and free of an isolated shock front. We suggest this unanticipated result may be realized experimentally and assess the potential for certain applications of this generic effect.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fracture Mechanics—Theory, Modeling and Applications

The field of fracture mechanics was developed during the throes of World War II, and since then, it has been a very active area of research. This is a very energetic and vibrant field because fracture processes are relevant for a vast range of engineering applications spanning different temporal and length scales. Depending on the application, material fracture and fragmentation may be either a desirable feature (for example, for the purpose of hydraulic fracturing operations), or something that is to be avoided at all costs (for example, in key components of mechanical systems). In some other instances, fractures are already present and must be accommodated through novel design (for example, in the case of earthquake ruptures occurring in the Earth’s crust). Because of this wide spectra of motivation, there is a continuous need for the fracture mechanics research community to gain more insight on how fractures are created, evolve, and interact with themselves and with material microstructures. In addition, there are still many remaining questions about how fracture propagation, growth, and interaction impact overall material behavior, and how to develop accurate models to predict this behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Radiation Damage in Materials—Helium Effects

Despite its scarcity in terrestrial life, helium effects on microstructure evolution and thermo-mechanical properties can have a significant impact on the operation and lifetime of applications, including: advanced structural steels in fast fission reactors, plasma facing and structural materials in fusion devices, spallation neutron target designs, energetic alpha emissions in actinides, helium precipitation in tritium-containing materials, and nuclear waste materials. The small size of a helium atom combined with its near insolubility in almost every solid makes the helium–solid interaction extremely complex over multiple length and time scales. This Special Issue, “Radiation Damage in Materials—Helium Effects”, contains review articles and full-length papers on new irradiation material research activities and novel material ideas using experimental and/or modeling approaches. These studies elucidate the interactions of helium with various extreme environments and tailored nanostructures, as well as their impact on microstructural evolution and material properties.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Energy Consumption and CO 2 Emissions in Ironmaking and Development of a Novel Flash Technology

The issues of energy consumption and CO 2 emissions of major ironmaking processes, including several new technologies, are assessed. These two issues are interconnected in that the production and use of fuels to generate energy add to the total amount of CO 2 emissions and the efforts to sequester or convert CO 2 require energy. The amounts of emissions and energy consumption in alternate ironmaking processes are compared with those for the blast furnace, currently the dominant ironmaking process. Although more than 90% of iron production is currently through the blast furnace, intense efforts are devoted to developing alternative technologies. Recent developments in alternate ironmaking processes, which are largely driven by the needs to decrease CO 2 emissions and energy consumption, are discussed in this article. This discussion will include the description of the recently developed novel flash ironmaking technology. This technology bypasses the cokemaking and pelletization/sintering steps, which are pollution prone and energy intensive, by using iron ore concentrate. This transformational technology renders large energy saving and decreased CO 2 emissions compared with the blast furnace process. Economic analysis indicated that this new technology, when operated using natural gas, would be economically feasible. As a related topic, we will also discuss different methods for computing process energy and total energy requirements in ironmaking.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Localized Strain Analysis of Ce- and Mg-Treated Cast Iron under Uniaxial Compression

Cast iron exhibits a wide range of mechanical properties, depending on its microstructural features. The microstructure of cast iron consists of several microconstituents with different elastic-plastic behavior, making the strain non-uniform across the bulk material. To understand the individual effects of these microconstituents on the overall mechanical behavior, local strain analysis using digital image correlation analysis was carried out. Samples with two different compositions (varying cerium, magnesium and silicon) were processed at different solidification velocities in a Bridgman furnace. Sections of the directionally solidified samples were loaded under uniaxial compression to measure global and local strain behavior. Despite the variability of the microstructure, the stress–strain curves obtained by digital image correlation (DIC) were found to react in a well-controlled way to changes in solidification velocity. It was observed that high-strain failure (greater than 15%) was accompanied by local straining of the softer ferritic phase, but during low-strain failure, local straining was not prominent. Higher nodularities, due to higher solidification velocities, raised the compressive strength without affecting the toughness significantly. Higher percentages of carbides led to higher compressive strengths with corresponding losses in ductility. The continuity of the matrix was also found to play an important role in the behavior during compression.

ductile failure↗
DOE OSTI2022

Effect of Grain Boundary Misorientation on Spall Strength in Ta via Shock-Free Simulations with Relatively Few Atoms

A suite of 37 molecular dynamics simulations is conducted at two system sizes to systematically characterize the role of grain boundary (GB) misorientation on spall strength in pure BCC tantalum (Ta). The systems studied consist of bicrystals with a single [110] symmetric tilt grain boundary. Two loading conditions are compared: (i) homogeneous extension under uniaxial strain simulated in this study and (ii) piston/flyer impact of sample, which induces heterogeneous deformation via shockwave propagation along the length of the sample. The piston/flyer impact is taken from the literature and run on the same set of GB misorientation angles using LAMMPS. The major finding here is that both methods result in similar spall strength predictions, but the homogeneous extension method generally requires two to three orders of magnitude fewer atoms and similar reductions in computational costs. Spall strength results systematically overpredict using this method, by about 10% for the dataset three orders of magnitude smaller than piston/flyer simulations, and 5% for the dataset two orders of magnitude smaller. Lastly, the effect of system size and pre-compression magnitude on spall strength is systematically characterized.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Heterogeneous Morphologies and Hardness of Co-Sputtered Thin Films of Concentrated Cu-Mo-W Alloys

Heterogeneous microstructures in Cu-Mo-W alloy thin films formed by magnetron co-sputtering immiscible elements with concentrated compositions are characterized using scanning transmission electron microscopy (STEM) and nanoindentation. In this work, we modified the phase separated structure of a Cu-Mo immiscible system by adding W, which impedes surface diffusion during film growth. The heterogeneous microstructures in the Cu-Mo-W ternary system exhibited bicontinuous matrices and agglomerates composed of Mo(W)-rich phase. This is unique, as these are the slower-diffusing species, contrasting past reports of binary Cu-Mo thin films that exhibited Cu-rich agglomerates. The bicontinuous matrices comprised of Cu-rich and Mo(W)-rich phases exhibited bilayer thicknesses of less than 5 nm. The hardness of these thin films measured using nanoindentation is reported and compared to similar multilayers and nanocomposites in binary systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Facile Aqueous Solution Route for the Growth of Chalcogenide Perovskite BaZrS 3 Films

The prototypical chalcogenide perovskite, BaZrS 3 (BZS), with its direct bandgap of 1.7–1.8 eV, high chemical stability, and strong light–matter interactions, has garnered significant interest over the past few years. So far, attempts to grow BaZrS 3 films have been limited mainly to physical vapor deposition techniques. Here, we report the fabrication of BZS thin films via a facile aqueous solution route of polymer-assisted deposition (PAD), where the polymer-chelated cation precursor films were sulfurized in a mixed CS 2 and Ar atmosphere. The formation of a single-phase polycrystalline BZS thin film at a processing temperature of 900 °C was confirmed by X-ray diffraction and Raman spectroscopy. The stoichiometry of the films was verified by Rutherford Backscattering spectrometry and energy-dispersive X-ray spectroscopy. The BZS films showed a photoluminescence peak at around 1.8 eV and exhibited a photogenerated current under light illumination at a wavelength of 530 nm. Temperature-dependent resistivity analysis revealed that the conduction of BaZrS 3 films under the dark condition could be described by the Efros–Shklovskii variable range hopping model in the temperature range of 60–300 K, with an activation energy of about 44 meV.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Embedded Ferroelectric Nanoclusters can drive Polarization Reversal in a Non-Ferroelectric Polar Film via the Proximity Effect

Heterogeneous nucleation from defects dominates the electric field required for polarization switching of ferroelectrics. Here, we consider the switching of a nominally non-switchable polar thin film of AlN due to the proximity effect arising from embedded ferroelectric nanoclusters of Al 1-x Sc x N. Using a Landau-Ginzburg-Devonshire thermodynamic approach and finite element modeling, we study the influence of nanocluster shape on polarization switching and domain nucleation emerging in AlN. The ferroelectric nanocluster boundary is modeled as a thin layer transitioning from Al 1-x Sc x N to AlN. We analyze the conditions under which polarization switching in the AlN film occurs at coercive fields significantly lower than its dielectric breakdown field. In the presence of spike-like Al 1-x Sc x N nanoclusters, the proximity effect enables switching of the spontaneous polarization in AlN and significantly reduces the corresponding coercive field. The internal field, which is depolarizing inside the AlN (due to its larger spontaneous polarization) and polarizing within the ferroelectric Al 1-x Sc x N nanoclusters (due to its smaller spontaneous polarization), lowers the potential barrier in the clusters and nucleates nanodomains at the Al 1-x Sc x N-AlN interface, forming localized regions of reversed polarization. Proximity effect can thus provide a pathway towards "thawing" previously "frozen" ferroelectrics through engineered nucleation for memory, actuation and optical technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Durable Module Materials Consortium (DuraMAT) FY 2021 Annual Report: New Results and a Renewed Consortium

The Durable Module Materials Consortium (DuraMAT) is a multi-lab consortium led by the National Renewable Energy Laboratory, with Sandia National Laboratories, SLAC National Accelerator Laboratory, and Lawrence Berkeley National Laboratory as core research labs. DuraMAT's overarching goal is to discover, develop, de-risk, and enable the rapid commercialization of improved materials, designs, predictive tests, and models for photovoltaic (PV) modules that increase performance, extend lifetime, and enable new applications. Technical results are highlighted throughout this report, and the new projects awarded for FY 2022 address many of the challenges to making 50-year, high-energy-yield modules that were identified in these working groups.

backsheet↗
DOE OSTI2024

Milestone report for MRT 8504: Commission EXAFS spectrometer with spectral range of 17.95-18.6 keV design to obtain EXAFS data for Pu L shell experiments

This milestone describes the development and fielding of EXAFS Phase II spectrometer designed to provide high quality (SNR>=5) EXAFS spectra for Plutonium measurements at the National Ignition facility (NIF). Benefits: the EXAFS data will be used by the High Energy Density (HED) Physics and more specifically the Focused Material Science program to measure the thermal state of compressed materials with good temperature sensitivity (~100-1000 Kelvin). Data with good signal to noise ratio (SNR>=5) and good spectral resolution allows the FMS program to fill a gap in diagnosing temperature to completely constrain material properties for weapon physics and Stockpile Stewardship applications.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Quantum Dynamics at Scale: Ultrafast Control of Emergent Functional Materials

Confluence of extreme-scale quantum dynamics simulations (i.e. quantum@scale) and cutting-edge x-ray free-electron laser experiments are revolutionizing materials science. An archetypal example is the exciting concept of using picosecond light pulses to control emergent material properties on demand in atomically-thin layered materials. This paper describes efforts to scale our quantum molecular dynamics engine toward the United States' first exaflop/s computer, under an Aurora Early Science Program project named "Metascalable layered material genome". Key algorithmic and computing techniques incorporated are: (1) globally-scalable and locally-fast solvers within a linear-scaling divide-conquer-recombine algorithmic framework; (2) algebraic `BLASification' of computational kernels; and (3) data alignment and loop restructuring, along with register and cache blocking, for enhanced vectorization and efficient memory access. The resulting weak-scaling parallel efficiency was 0.93 on 131,072 Intel Xeon Phi cores for a 56.6 million atom (or 169 million valence-electron) system, whereas the various code transformations achieved 5-fold speedup. The optimized simulation engine allowed us for the first time to establish a significant effect of substrate on the dynamics of layered material upon electronic excitation.

Algebraic BLASification↗
DOE OSTI2025

Sandwiching of MOF nanoparticles between graphene oxide nanosheets among ice grains

Current strategies to tailor the formation of nanoparticle clusters require specificity and directionality built into the surface functionalization of the nanoparticles by involved chemistries that can alter their properties. Here, we describe a non-disruptive approach to place nanomaterials of different shapes between nanosheets, i.e., nano-sandwiches, absent any pre-modification of the components. We demonstrate this with metal-organic frameworks (MOFs) and silicon oxide (SiO 2 ) nanoparticles sandwiched between graphene oxide (GO) nanosheets, MOF-GO and SiO 2 -GO, respectively. For the MOF-GO, the MOF shows significantly enhanced conductivity and retains its original crystallinity, even after one-year exposure to aqueous acid/base solutions, where the GO effectively encapsulates the MOF, shielding it from polar molecules and ions. The MOF-GOs are shown to effectively capture CO 2 from a high-humidity flue gas while fully maintaining their crystallinities and porosities. Similar behavior is found for other MOFs, including water-sensitive HKUST-1 and MOF-5, promoting the use of MOFs in practical applications. The nanoparticle sandwich strategy provides opportunities for materials science in the design of nanoparticle clusters consisting of different materials and shapes with predetermined spatial arrangements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗