Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “local strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Emissions Measurements from a Lobed Fuel Injector/Burner

The present experimental study examines NO(x) and CO emissions associated with alternative fuel injector geometries. These injectors mix fuel and air to differing extents and thus create different local equivalence ratios upstream of flame ignition and stabilization. Two of the devices studied are lobed fuel injectors, in which mixing of reactants is associated with stream wise vorticity generation and straining of fuel-air interfaces, while the third is a non-lobed fuel injector which creates relatively little fuel-air mixing prior to ignition.Results show that one lobed injector geometry appears to produce locally lean premixed flame structures, resulting in low NO. emissions when compared with non-lobed injector emissions. The other lobed injector geometry appears to produce a local fuel-air mixture which is closer to stoichiometric conditions, with NO(x) emissions that are actually higher than for the non-lobed injector. For both lobed injector geometries examined here, CO emissions become high for over-all lean operating conditions, consistent with premixed combustion behavior. The present study demonstrates the importance of control of the local equivalence ratio in minimizing burner emissions.

Mitchell, M. G.↗
DOE OSTI2026

Effect of Specimen Thickness on Fracture Toughness and Plane Stress to Plane Strain Transition in Medium-Density Polyethylene

This study investigates the effect of specimen thickness on fracture toughness and the transition from plane stress to plane strain conditions in Medium-Density Polyethylene (MDPE) using Single Edge Notched Bend (SENB) specimens. Three thickness groups (7.5 mm, 9.0 mm, and 12.1 mm) were tested following ASTM D5045 protocol. Conditional stress intensity factors (KQ) increased from 2.2 MPavm to 2.8 MPavm with increasing thickness, demonstrating significant size dependency. Confocal microscopy revealed a 34% reduction in maximum crack tip opening displacement (CTOD) from 0.478 mm to 0.314 mm as thickness increased, with plastic zone lateral extent decreasing by 32%. This quantitative evidence validates Irwin's theoretical prediction of plastic zone size transition from plane stress r_y˜ (1/2p) (K_I/s_y )^2 to plane strain conditions r_y˜ (1/6p) (K_I/s_y )^2.Scanning electron microscopy confirmed progressive suppression of shear lips and evolution from ductile tearing with extensive polymer chain drawing in thin specimens to localized crazing in thick specimens. Despite all specimens satisfying the ASTM D5045 criterion (B = 2.5(KQ/s_y )^2 ) ,residual shear lips persisted even in the thickest specimens, demonstrating that nominal size requirements alone are insufficient for achieving complete plane strain conditions in highly ductile polymers. The findings emphasize the necessity of integrated analytical and morphological assessment for valid fracture toughness characterization, with critical implications for life assessment and integrity prediction in thick-section polymer components such as natural gas distribution pipelines.

Medium-Density Polyethylene↗
DOE OSTI2024

Large eddy simulation of lean blow-off in swirl-stabilized flame with the subgrid dissipation concept

The lean blow-off mechanism of the premixed swirl flame is numerically investigated by large eddy simulation (LES) with the subgrid dissipation concept (SDC) combustion model. Three simulated cases cover stable, near blow-off, and transient conditions. Compared with the experiment, the LES-SDC approach captures the flow and combustion features for stable and near blow-off conditions. More importantly, the predictions of the blowoff procedure and duration agree satisfactorily with the experiment, indicating that the LES-SDC approach is a promising tool for predicting strong, unsteady turbulent combustion processes. Further, the numerical results are used to investigate the blow-off mechanism. Two stages in the blow-off procedure are specified. The first is the necking and extinction of the downstream flame surface, and the second is the shrinking of the upstream flame surface. The blow-off mechanism is well explained by the theory of stretched flame extinction. At the end of the recirculation zone, the large negative radial velocity pushes the flame to the central line. The combustion process here can be abstracted as the stretched counter-flame of the reactant-reactant configuration. The excessive flame stretch dominates the flame extinction and triggers the blow-off event. The upstream flame resists the intense stretch with the help of hot product recirculation, and the combustion here can be idealized as the counter-flame of the reactant-product configuration. The alignment of the temperature gradient and flow velocity, together with the excessive stretch, clearly indicates the tendency of flame local extinction. A Damköhler number-based blow-off criterion is raised from the mean flow strain rate and laminar flame bulk extinction strain rate.

42 ENGINEERING↗
DOE OSTI2024

Microstructure manipulation via machining and heat treatments in hybrid manufacturing of 316L stainless steel

Hybrid manufacturing combines additive and subtractive (machining) processes in a single platform to reduce the total time to fabricate a component in its final form. Here we show that if sufficient plastic deformation can be imparted to the material during machining, recrystallization can be triggered during post-fabrication heat treatment. This can enable highly localized microstructure control. Additionally, we show that stainless steel 316L, when machined without coolant accumulates significant plastic strain compared to when machined with coolant that results in faster recrystallization kinetics during heat treatment. These effects are limited to the surface while the bulk microstructure remains unaffected.

316L stainless steel↗
NASA NTRS1975

Growth defects in thick ion-plated coatings

Industrial ion plating conditions were selected to deposit metallic coatings such as copper, gold, and chromium 2 micrometer thick on metal and glass substrates. The surface finishes of 304 stainless steel, copper, and brass were utilized with mechanically and electrolytically polished surfaces. Nodular growth occurred in these coatings during ion plating as revealed by scanning electron microscopy. Surface irregularities such as scratches, steps, ledges, and so forth are responsible for outward growth, the typical cone type, whereas surface contaminants and loosely settled foreign particles are responsible for lateral growth; namely, the extreme localized surface outgrowths. These defect crystallographic features create porosity in the coatings when subjected to stresses and strains.

Spalvins, T.↗
NASA NTRS1988

Computational and experimental studies of LEBUs at high device Reynolds numbers

The present paper summarizes computational and experimental studies for large-eddy breakup devices (LEBUs). LEBU optimization (using a computational approach considering compressibility, Reynolds number, and the unsteadiness of the flow) and experiments with LEBUs at high Reynolds numbers in flight are discussed. The measurements include streamwise as well as spanwise distributions of local skin friction. The unsteady flows around the LEBU devices and far downstream are characterized by strain-gage measurements on the devices and hot-wire readings downstream. Computations are made with available time-averaged and quasi-stationary techniques to find suitable device profiles with minimum drag.

Bertelrud, Arild↗
NASA NTRS1987

Research on complex turbulent flows at the UW (overall effort)

Development of a pressure-strain model, an algebraic stress model, and wall functions appropriate for flows with spanwise variations in the local wall shear stress are accomplished. Furthermore, a hot-wire measurement technique was also developed for determining the local mean velocity and Reynolds stresses in a complex flow. Experiments were performed on supersonic and subsonic turbulent flow in a square duct, flow about a strut-endwall, flow within a transition duct, and on co-flowing annular jets with swirl. All results are presented in a viewgraph format.

Gessner, F. B.↗
NASA NTRS1993

Three-dimensional analysis of anisotropic spatially reinforced structures

The material-adaptive three-dimensional analysis of inhomogeneous structures based on the meso-volume concept and application of deficient spline functions for displacement approximations is proposed. The general methodology is demonstrated on the example of a brick-type mosaic parallelepiped arbitrarily composed of anisotropic meso-volumes. A partition of each meso-volume into sub-elements, application of deficient spline functions for a local approximation of displacements and, finally, the use of the variational principle allows one to obtain displacements, strains, and stresses at anypoint within the structural part. All of the necessary external and internal boundary conditions (including the conditions of continuity of transverse stresses at interfaces between adjacent meso-volumes) can be satisfied with requisite accuracy by increasing the density of the sub-element mesh. The application of the methodology to textile composite materials is described. Several numerical examples for woven and braided rectangular composite plates and stiffened panels under transverse bending are considered. Some typical effects of stress concentrations due to the material inhomogeneities are demonstrated.

Bogdanovich, Alexander E.↗
NASA NTRS1994

Vapor generator wand

In low speed wind tunnels it is often desirable to visualize airflow to augment observations made with instruments such as strain and pressure gages. Current technology devices for delivery of a vapor are bulky and thus disrupt local airflow. It is the object of this invention to provide a device capable of delivering a stream of vapor with a minimal effect on local airflow. The present invention achieves this object by utilizing a narrow tube as a heating device for producing the vapor. Running an electrical current through the tube provides resistive heating to a liquid which produces a vapor when boiled. As the entire heating and delivery portion of the device is simply a small cylinder the disruption to airflow within the tunnel is minimized. this allows an experimenter to place the source of vapor fairly close to a model without causing too much change to the model data. The novelty of the present invention lies in reducing the bulk of current technology devices by combining the acts of heating and delivery.

Robelen, David B.↗
DOE OSTI2025

Heavy boron doping effects on biaxially tensile strained germanium (>1.5%) investigated via structural characterization, effective lifetime assessment and atomistic modeling

Highly tensile strained germanium (ε-Ge) represents an essential material system for emerging electronic and photonics applications. Moreover, adjusting the doping levels to moderate or high concentrations can effectively tailor the properties of ε-Ge for specific applications. This article combines experimental characterization with a theoretical framework to examine the effects of heavy elemental boron (B) doping on pseudomorphic sub-50 nm ε-Ge. High resolution X-ray diffractometry is used to validate tensile strain levels of 1.53% and 1.68% in Ge epilayers, surpassing the indirect-to-direct band gap crossover point at ∼1.5% biaxial tensile strain. Cross-sectional transmission electron microscopy revealed visual evidence of stacking faults and surface roughening in 1.68% ε-Ge, although a coherent and abrupt Ge/III–V heterointerface is observed, devoid of interfacial misfit dislocations. Effective lifetime measurements demonstrated approximately twofold enhancement in 1.53% B-doped ε-Ge (N B ∼7 × 10 19 cm −3 ) compared to its unstrained B-doped counterpart, while no such improvement was observed in 1.68% B-doped ε-Ge. This lack of enhancement is attributed to the presence of stacking faults and surface roughness within the ε-Ge epilayer. Through density functional theory calculations, we independently demonstrate that substitutional B atoms induce local deformation of Ge–Ge bonds in both unstrained Ge and ε-Ge epilayers, resulting in an additive tensile strain. This phenomenon could potentially lead to dynamic reduction and overcoming of the critical layer thickness for the system, facilitating the nucleation and subsequent glide of 90° leading Shockley partial dislocations, thereby generating stacking faults. In essence, these findings establish an upper limit on the B-doping concentration that can be achieved in highly ε-Ge epilayers, and collectively, offer valuable insights into the significance of heavy doping in Ge-based heterostructures. As such, this study delineates a fundamental constraint for integrating heavily doped ε-Ge in high-performance optoelectronic systems, necessitating precise strain-doping co-optimization to avoid performance degradation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Site-specific nanoscale characterization of zirconium hydrides in the hydride rim structure of hydrogen-charged zircaloy-4 cladding

Zircaloy-4 cladding tubes were hydrogen-charged using a static pressure hydrogen charging method to experimentally produce a zirconium-hydride rim structure similar to that observed in Zircaloy-4 cladding tubes after operation in commercial light-water nuclear reactors. Detailed characterization was performed using electron energy loss spectroscopy (EELS) and four-dimensional scanning transmission electron microscopy (4D-STEM). By mapping the position of the plasmon peak in the low-loss EELS spectrum, it was determined that the zirconium hydrides formed were predominantly solid δ-phase zirconium hydrides. 4D-STEM was used to generate phase and strain maps at nanoscale. The interactions between two zirconium hydride platelets less than 200 nm apart leads to the localized lattice rotations and possible phase change, revealing a potential hydride growth mechanism.

4D-STEM↗
NASA NTRS2004

Effects of heavy ion to the primary culture of mouse brain cells

To investigate effects of low dose heavy particle radiation to CNS system, we adopted mouse neonatal brain cells in culture being exposed to heavy ions by HIMAC at NIRS and NSRL at BNL. The applied dose varied from 0.05 Gy up to 2.0 Gy. The subsequent biological effects were evaluated by an induction of apoptosis and neuron survival focusing on the dependencies of the animal strains, SCID, B6, B6C3F1, C3H, used for brain cell culture, SCID was the most sensitive and C3H the least sensitive to particle radiation as evaluated by 10% apoptotic criterion. The LET dependency was compared with using SCID and B6 cells exposing to different ions (H, C, Ne, Si, Ar, and Fe). Although no detectable LET dependency was observed in the high LET (55-200 keV/micrometers) and low dose (<0.5 Gy) regions. The survivability profiles of the neurons were different in the mouse strains and ions. In this report, a result of memory and learning function to adult mice after whole-body and brain local irradiation at carbon ion and iron ion.

NASA Discipline Radiation Health↗
DOE OSTI2025

Laser‐Powder Melt Pool Solidification Dynamics and Microstructural Engineering of Ti‐5553 Microlattices

The fine geometric and topological control afforded by additive manufacturing technologies has enabled the manufacture of architected materials across length scales, and enabling tunable mechanical performance as a function of local and global design. Progress has been made to tune the mechanical response of architected materials through geometry, but understanding how the geometry and processing conditions will inform the microstructure remains a challenge due to the rapid solidification in laser powder bed fusion. This study uses in situ X-ray imaging and electron backscatter diffraction microscopy to demonstrate that the melt pool size, microstructure morphology, and elastic strain distribution is influenced by a combination of lattice geometry and laser processing conditions. These results indicate that within larger melt pools the local thermal gradients are sufficient to enable a columnar-to-equiaxed transition across the melt pool. Furthermore, the solidification mechanisms producing these microstructures are examined across the first 5 ms of melting and solidification, described via in situ high-speed X-ray imaging and mirrored via multiphysics simulation.

additive manufacturing↗
DOE OSTI2025

Strain release through hydrogen bond–mediated layer twisting

Strain engineering, enabling the precise control over structure and functional properties, is a key strategy for the design of advanced materials. However, the mechanisms governing strain evolution and release at the nanoscale remain largely unexplored. In this study, we leverage in situ heating transmission electron microscopy and synchrotron x-ray spectroscopy to investigate the strain relaxation pathways of boehmite (γ-AlOOH) at 575 kelvin by revealing real-time structural dynamics. Through tracking the moiré pattern evolution, we identify distinct strain release mechanisms, including layer twisting, defect formation, and domain restructuring. Our neural network potential calculations reveal that energy fluctuations at small twist angles are dominated by an interference-like interaction modulation of hydrogen bonds between boehmite interlayers, with metastable twisted structures corresponding to local minima of the potential energy landscape. This work establishes a previously unidentified paradigm of two-dimensional layer twisting mediated by hydrogen bonding, offering insights into strain-driven transformation mechanisms, and thus may have broad implications for strain in material and earth sciences.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Robust Ferromagnetism in Highly Strained SrCoO 3 Thin Films

Epitaxial strain provides important pathways to control the magnetic and electronic states in transition-metal oxides. However, the large strain is usually accompanied by a strong reduction of the oxygen-vacancy formation energy, which hinders the direct manipulation of their intrinsic properties. Here, using a postdeposition ozone annealing method, we obtain a series of oxygen stoichiometric SrCoO 3 thin films with the tensile strain up to 3.0%. We observe a robust ferromagnetic ground state in all strained thin films, while interestingly the tensile strain triggers a distinct metal-to-insulator transition along with the increase of the tensile strain. The persistent ferromagnetic state across the electrical transition therefore suggests that the magnetic state is directly correlated with the localized electrons, rather than the itinerant ones, which then calls for further investigation of the intrinsic mechanism of this magnetic compound beyond the double-exchange mechanism.

36 MATERIALS SCIENCE↗
NASA NTRS1986

North American-Pacific relative plate motion in southern California from interferometry

VLBI measurements of baselines crossing the San Andreas fault zone in southern California have provided observational constraints on rates of elastic tectonic strain accumulation. The single site located near this fault (the JPL site) moves in a direction concordant with the Pacific plate motion vector but at approximately half the net rate relative to North America. This motion agrees approximately in amount with geologically determined displacement rates on the San Andreas fault alone but not with the local strike of the fault. When considered together with complementary geodetic data, these results suggest a complex relation between the short-term accumulation of elastic strain and its permanent accommodation on existing faults.

Lyzenga, G. A.↗
DOE OSTI2019

Lattice disorder effect on magnetic ordering of iron arsenides

This study investigates magnetic ordering temperature in nano- and mesoscale structural features in an iron arsenide. Although magnetic ground states in quantum materials can be theoretically predicted from known crystal structures and chemical compositions, the ordering temperature is harder to pinpoint due to potential local lattice variations that calculations may not account for. In this work we find surprisingly that a locally disordered material can exhibit a significantly larger Néel temperature (T N ) than an ordered material of precisely the same chemical stoichiometry. Here, a EuFe 2 As 2 crystal, which is a ‘122’ parent of iron arsenide superconductors, is found through synthesis to have ordering below T N = 195 K (for the locally disordered crystal) or T N = 175 K (for the ordered crystal). In the higher T N crystals, there are shorter planar Fe-Fe bonds [2.7692(2) Å vs. 2.7745(3) Å], a randomized in-plane defect structure, and diffuse scattering along the [00 L] crystallographic direction that manifests as a rather broad specific heat peak. For the lower T N crystals, the a-lattice parameter is larger and the in-plane microscopic structure shows defect ordering along the antiphase boundaries, giving a larger T N and a higher superconducting temperature (T c ) upon the application of pressure. First-principles calculations find a strong interaction between c-axis strain and interlayer magnetic coupling, but little impact of planar strain on the magnetic order. Neutron single-crystal diffraction shows that the low-temperature magnetic phase transition due to localized Eu moments is not lattice or disorder sensitive, unlike the higher-temperature Fe sublattice ordering. This study demonstrates a higher magnetic ordering point arising from local disorder in 122.

36 MATERIALS SCIENCE↗
DOE OSTI2020

New self-consistent homogenization for thermo-elastic polycrystals with imperfect interfaces

Here we present a new thermo-elastic self-consistent formulation to calculate the thermo-mechanical response of polycrystalline aggregates with imperfect interfaces. The new model is based on an improved treatment of the effect of imperfect interfaces on the micromechanical response of the grains compared to pre-existing models. New expressions/algorithms are derived for the effective elastic and thermal properties, localization relations, and calculation of intragranular field fluctuations. In addition, derivation of a novel integral equation for the strain field in a heterogeneous elastic medium subjected to arbitrary thermal strain field and displacement jumps is presented. The new model is applied to study the effective thermo-elastic properties and average field fluctuations as a function of the interface properties for imperfectly-bonded triaminotrinitrobenzene (TATB) polycrystalline granular aggregates. The proposed formulation is general in the sense that it can be extended to other material systems and deformation regimes that require a proper consideration of the effect of imperfect interface properties on the material's thermo-mechanical response.

36 MATERIALS SCIENCE↗