Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lamination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Bolt-bearing fatigue of a graphite/epoxy laminate

Graphite/epoxy laminates were tested under bolt-bearing loads for a range of bolt clampup torques and for several test conditions involving water. High clampup torque improved both the static strength and fatigue limit by about 100 percent compared to a simple pin-bearing case, which had no through-the-thickness constraint. The static strength improvement was explained in terms of failure modes. Bolt clampup also influenced the hole elongation that developed before failure. For both the static and fatigue tests, the hole elongations were much larger for the low-torque clampup. Tests in water degraded static bearing strength only slightly, but reduced the fatigue limit about 40 percent below that for tests conducted in air.

Crews, J. H., Jr.↗
NASA NTRS1980

Stability optimization of laminated composite plates

The optimum design of plates with orthotropic layers under axial compression and shear is discussed. The plates considered are the laminates of N orthotropic layers whose principal material axes coincide with the plate axes. Each layer is assumed to have the same thickness and an equal number of fibers in the direction of + alpha sub i and - alpha sub i with respect to the plate axis. The fiber directions which give the highest axial buckling stress and the highest shear buckling stress are found by utilizing a mathematical optimization technique for various aspect ratios of the plates. Inhomogeneity in the direction of the plate thickness (stacking sequence) is taken into account in this analysis.

Hirano, Y.↗
NASA NTRS1980

Interlaminar stress singularities at a straight free edge in composite laminates

A quasi three dimensional finite element analysis was used to analyze the edge stress problem in four-ply, composite laminates. Convergence studies were made to explore the existence of stress singularities near the free edge. The existence of stress singularities at the intersection of the interface and the free edge is confirmed.

Raju, I. S.↗
NASA NTRS1979

Optimum design of laminated plates under shear

This paper is concerned with the optimum design of plates with orthotropic layers under shear. The plates considered are the laminates of N orthotropic layers whose principal material axes coincide with the plate axes. Each layer is assumed to have the same thickness and an equal number of fibers in the direction of + alpha sub i and - alpha sub i with respect to the plate axis. The fiber directions which give the highest shear buckling stress are found by utilizing a mathematical optimization technique.

Hirano, Y.↗
NASA NTRS1979

Note on the effect of transverse shear deformation in laminated anisotropic plates

The paper describes the development of some computer methods in applied mechanics. It begins with a distribution of primary stresses in laminated plates, followed by a determination of the associated statically consistent transverse shearing stress. The last section deals with the use of an energy principle for the utilization of these expressions for primary and transverse stresses. The purpose of this is to obtain two-dimensional constitutive equations involving transverse shear deformations and transverse shear stress resultants.

Reissner, E.↗
NASA NTRS1979

Frequency effect on the fatigue life of a laminated composite

Effects of load frequency on the fatigue behavior of notched (+ or - 45 deg)2s laminated graphite/epoxy composites are investigated. Experimental results are obtained using four frequencies at three load levels. Temperature rises near the center hole are also measured. It is found that when temperature increase during the fatigue test is small, fatigue life increases as the load frequency increases. However, an increase in the near hole temperature results in a reduction in fatigue life. A theoretical model based upon crack propagation in viscoelastic media is presented. The model is modified to account for the temperature effect.

Sun, C. T.↗
NASA NTRS1980

Fracture modes of high modulus graphite/epoxy angleplied laminates subjected to off-axis tensile loads

Angleplied laminates of high modulus graphite fiber/epoxy were examined in several ply configurations at various tensile loading angles to the zero ply direction to determine the effects of ply orientations on tensile properties, fracture modes, and fracture surface characteristics of the various plies. Experimental results consist of stress-strain data, selected plots, fracture stresses and strains, and scanning electron microscope (SEM) photographs of fracture surfaces. It was found that the stress-strain curves were linear to fracture, and that although fracture surface characteristics for a given fracture mode are similar to those for the same fracture mode in uniaxial specimens, no simple load angle range can be associated with a given fracture mode. It was also concluded that SEM results must be supplemented with ply stress calculations in order to identify ranges of fracture modes occurring as a function of ply orientation with respect to the load direction.

Sinclair, J. H.↗
NASA NTRS1980

Proof test and fatigue of unnotched composite laminates

A comprehensive fatigue and residual strength degradation model has been used to predict the effect of proof loads (or high load) on the statistical fatigue behavior of composite laminates. The validity of the theoretical model is confirmed by the experimental test results. The correlation between the test results and the theoretical distributions of the fatigue life and the residual strength for composite specimens with or without the effect of proof loads is shown to be very good.

Yang, J. N.↗
NASA NTRS1982

Predicting the Strengths of Angle-Plied Laminates

Simplified convenient procedure has been developed that can be used to determine elastic and strength properties of angle-plied laminates. Method is suitable for use with pocket calculator. Consists of simple equations and graphs of ply combinations from most frequently used composites. Procedure makes use of well-known transformation equations, ply stress influence coefficients, and ply uniaxial composites including interply and intraply hybrids.

Chamis, C. C.↗
NASA NTRS1980

Method for alleviating thermal stress damage in laminates

A method is provided for alleviating the stress damage in metallic matrix composites, such as laminated sheet or foil composites. Discontinuities are positively introduced into the interface between the layers so as to reduce the thermal stress produced by unequal expansion of the materials making up the composite. Although a number of discrete elements could be used to form one of the layers and thus carry out this purpose, the discontinuities are preferably produced by simply drilling holes in the metallic matrix layer or by forming grooves in a grid pattern in this layer.

Hoffman, C. A.↗
NASA NTRS1981

On the relationship between engineering properties and delamination of composite laminates

The influence of the coefficient of mutal influence, Poisson's ratio and coefficients of thermal and moisture expansion on delamination is studied. Engineering theories are compared to finite element and experimental results. It is shown that the mismatch in coefficients of mutual influence can have a strong influence on delamination with fiber angles in the 10-15 degree range being critical for adjacent layer combinations. The mismatch in coefficient of mutual influence is reduced by a factor of two and the interlaminar shear stress is reduced significantly when the + or - adjacent layers are interspersed between 0 and 90 degree layers. It is shown how the results can be used for design of composite laminates.

Herakovich, C. T.↗
NASA NTRS1981

Fatigue degradation in compressively loaded composite laminates

The effect of imbedded delaminations on the compression fatigue behavior of quasi-isotropic, T300/5208, graphite/epoxy laminates was investigated. Teflon imbedments were introduced during panel layup to create delaminations. Static and constant amplitude (R=10, omega = 10 Hz) fatigue tests were conducted. S-N data and half life residual strength data were obtained. During static compression loading, the maximum deflection of the buckled delaminated region was recorded. Under compression fatigue, growth of the imbedded delamination was identified as the predominant failure mode in most of the test cases. Specimens that exhibited others failures had a single low stiffness ply above the Teflon imbedment. Delamination growth during fatigue was monitored using DIB enhanced radiography. In specimens with buried delaminations, the dye penetrant (DIB) was introduced into the delaminated region through a minute laser drilled hole, using a hypodermic needle. A low kV, microfocus, X-ray unit was mounted near the test equipment to efficiently record the cyclic growth of buried delaminations on Polaroid film.

Ramkumar, R. L.↗
NASA NTRS1981

Test evaluation of a laminated wood wind turbine blade concept

A series of tests conducted on a root end section of a laminated wood wind turbine blade are reported. The blade to hub transition of the wood blade uses steel studs cast into the wood D spar with a filled epoxy. Both individual studs and a full scale, short length, root section were tested. Results indicate that the bonded stud concept is more than adequate for both the 30 year life fatigue loads and for the high wind or hurricane gust loads.

Faddoul, J. R.↗
NASA NTRS1981

Method for alleviating thermal stress damage in laminates

The method is for metallic matrix composites, such as laminated sheet or foil composites. Non-intersecting discrete discontinuities are positively introduced into the interface between the layers so as to reduce the thermal stress produced by unequal expansion of the materials making up the composite. The discontinuities are preferably produced by drilling holes in the metallic matrix layer. However, a plurality of discrete elements may be used between the layers to carry out this purpose.

Hoffman, C. A.↗
NASA NTRS1980

Status of high-temperature laminating resins and adhesives

High-temperature polymers now being developed as adhesives and composite matrices are reviewed, including aromatic polyimides, polybenzimidazoles, polyphenylquinoxalines, nadic end-capped imide oligomers, maleimide end-capped oligomers, and acetylene-terminated imide oligomers. The mechanical properties of laminates based on these resins are reported together with preliminary test results on the adhesive properties for titanium-to-titanium and composite-to-composite lap shear specimens.

Hergenrother, P. M.↗
NASA NTRS1980

An assessment of buffer strips for improving damage tolerance of composite laminates

Graphite/epoxy panels with buffer strips were tested in tension to measure their residual strength with crack-like damage. Panels were made with (45/0/-45/90)2S and (45/0/-45/0)2S layups. The buffer strips were parallel to the loading direction. They were made by replacing narrow strips of the 0 deg graphite plies with strips of either 0 deg S-Glass/epoxy or Kevlar-90/epoxy on either a one-for-one or a two-for-one basis. In a third case, 0 deg graphite/epoxy was used as the buffer material and thin, perforated Mylar strips were placed between the 0 deg plies and the cross-plies to weaken the interfaces and thus to isolate the 0 deg plies. Some panels were made with buffer strips of different width and spacings. The buffer strips arrested the cracks and increased the residual strengths significantly over those of plain laminates without buffer strips. A shear-lag type stress analysis correctly predicted the effects of layup, buffer material, buffer strip width and spacing, and the number of plies of buffer material

Poe, C. C., Jr.↗
NASA NTRS1980

Analysis of fatigue damage in composite laminates

An attempt is made to give a comprehensive characterization of processes of degradation in type 1 and 2 laminated composites under cyclic (fatigue) loading; based on the discovery of a 'characteristic damage state' that forms independently of load history and is determined by laminae properties, orientation and stacking sequence alone. The detailed nature of this state, its formation and its influence on strength, life and stiffness, is discussed.

Reifsnider, K. L.↗
NASA NTRS1981

Edge delamination in angle-ply composite laminates

Edge delamination has caused severe concern in the design and analysis of advanced composite materials and structures. Due to its complex nature, very limited knowledge for the problem is currently available. It involves not only geometric and material discontinuities but also inherently coupled mode I, II and III fracture in the layered anisotropic system. Based on complex-variable stress potentials in the anisotropic elasticity theory and eigenfunction expansion, exact orders of the crack-tip stress singularity and complete field solutions are obtained. Results are given for edge delaminated, angle-ply composites subjected to uniform axial extension for illustrative purposes. Effects of geometric, lamination, and crack variables are determined.

Wang, S. S.↗