Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “halide perovskite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Polariton Dynamics in Two-Dimensional Ruddlesden–Popper Perovskites Strongly Coupled with Plasmonic Lattices

Strong coupling between light and matter can produce hybrid eigenstates known as exciton-polaritons. Although polariton dynamics are important photophysical properties, the relaxation pathways of polaritons in different coupling regimes have seen limited attention. This paper reports the dynamics of hybridized states from 2D Ruddlesden-Popper perovskites coupled to plasmonic nanoparticle lattices. The open cavity architecture of Al lattices enables the coupling strength to be modulated by varying either the lead halide perovskite film thickness or the superstrate refractive index. Both experiments and finite-difference time-domain simulations of the optical dispersion diagrams showed avoided crossings that are a signature of strong coupling. Furthermore, our analytical model also elucidated the correlation between the exciton/plasmon mixing ratio and polariton coupling strength. Using fs-transient absorption spectroscopy, we found that both the upper and lower polaritons have shorter lifetimes than the excitons and that polaritons can show faster excited state dynamics when they have access to additional energy transfer channels.

2D perovskite↗
DOE OSTI2022

Structural Changes in Molten Salt Fuel and/or Waste Stream Compounds Cs 2 UCl 6 and Cs 2 UO 2 Cl 4 from Room Temperature to Melting and Related Materials [Slides]

Perovskite phases have been explored in recent literature as waste forms for long term storage of radioactive waste from molten salt reactors specifically. Synthesis of new halide perovskite phases can inform these efforts as well as molten salt reactor chemistry in general. Inorganic perovskites have also shown promise as new scintillating materials for detection of X-rays and gamma rays. Modifying the structure and chemistry of these compounds, perhaps with organic components, could be used to synthesize new scintillating compounds or modify the properties of existing ones. Both U 6+ and U 4+ readily form compounds with a striking similarity to vacancy ordered perovskites (Cs 2 UO 2 Cl 4 and Cs 2 UCl 6 ). Each of these compounds is relevant to molten salt reactor chemistry and/or waste streams. These phases could from in uranium chloride salt systems or waste streams: Cs being a fission product.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Bidentate Lewis bases are preferred for passivation of MAPbI 3 surfaces: A time-domain ab initio analysis

We report chemical passivation is a predominant approach to inhibit intrinsic defects responsible for electron–hole recombination in perovskite solar cells. Using time-domain density functional theory combined with nonadiabatic molecular dynamics, we demonstrate defect passivation by separation of electrons and holes in metal halide perovskites (MHPs), and show that bidentate ligands exhibit the best performance. Defects in traditional semiconductors create deep midgap states, and passivation eliminates these states. In contrast, common defects produce no deep midgap states in MHPs. Instead, defects localize electrons and holes around defect sites, enhancing electron–hole interaction. Defect passivation in MHPs acts to separate charges, decreasing electron–hole and charge–phonon interactions, and increasing charge lifetimes. Bidentate ligands work best, because they can passivate both unsaturated chemical bonds created due to vacancy defects. Bidentate ligands with spatially separated binding sites are preferred, since they provide better match to the sparse inorganic lattice of MHPs. Similar to the Lewis base ligands, water also acts as a ligand and extends charge lifetimes, with the oxygen atom donating its lone electron pair to the defect site. However, water accelerates chemical degradation of MHPs. The binding energy of most ligands is larger than that of water, and therefore, the ligands displace water, increase MHP stability and prolong carrier lifetimes. The established physical mechanism of defect passivation, and the specific principles guiding the choice of passivating molecules advance our understanding of the exceptional properties of MHPs and suggest routes for further improvement of MHP performance in solar energy and optoelectronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of intrinsic and atmospherically induced defects in narrow bandgap (FASnI 3 ) x (MAPbI 3 ) 1- x perovskite films and solar cells

Narrow band gap mixed tin (Sn) + lead (Pb) perovskites are vital as the bottom sub-cell absorber in high efficiency all-perovskite polycrystalline tandem solar cells. Here, we report on the impact of mixed cation composition and atmospheric exposure of perovskite films on sub-gap absorption in films and performance of solar cells based on narrow band gap mixed formamidinium (FA) + methylammonium (MA) and Sn+Pb halide perovskites, (FASnI 3 ) x (MAPbI 3 ) 1- x . Structural and optical properties of 0.3 ≤ x ≤ 0.8 (FASnI 3 ) x (MAPbI 3 ) 1- x perovskite thin film absorbers with band gaps ranging from 1.25 ( x = 0.6) to 1.34 eV (x = 0.3) are probed with and without atmospheric exposure. Urbach energy, which quantifies the amount of sub-gap absorption, is tracked for pristine perovskite films as a function of composition, with x = 0.6 and 0.3 demonstrating the lowest and highest Urbach energies of 23 and 36 meV, respectively. Films with x = 0.5 and 0.6 compositions show less degradation upon atmospheric exposure than higher or lower Sn-content films having greater sub-gap absorption. The corresponding solar cells based on the x = 0.6 absorber show the highest device performance. Despite having a low Urbach energy, higher Sn-content solar cells show reduced device performances as the amount of degradation via oxidation is the most substantial.

14 SOLAR ENERGY↗
DOE OSTI2020

0D and 2D: The Cases of Phenylethylammonium Tin Bromide Hybrids

Tin halide perovskites and perovskite-related materials have emerged as promising lead-free hybrid materials for various optoelectronic applications. While remarkable progress has been achieved in the development of organic tin halide hybrids with diverse structures and controlled dimensionalities at the molecular level, some controversial results that have been reported recently need to be addressed. For instance, different photophysical properties have been reported for two-dimensional (2D) (PEA) 2 SnBr 4 (PEA = phenylethylammonium) by several groups with distinct emission peaks at around 468 and 550 nm. Here we report our efforts in the synthesis of phenylethylammonium tin bromide hybrids with zero-dimensional (0D) and 2D structures, and characterizations of their structural and photophysical properties. 0D [(PEA) 4 SnBr 6 ][(PEA)Br] 2 [CCl 2 H 2 ] 2 was found to exhibit strong yellow emission peak at 566 nm with a photoluminescence quantum efficiency (PLQE) of ~90%, while 2D (PEA) 2 SnBr 4 had weak emission peak at 470 nm with a PLQE of <0.1%. Interestingly, 0D [(PEA) 4 SnBr 6 ][(PEA)Br] 2 [CCl 2 H 2 ] 2 can be converted into 2D (PEA) 2 SnBr 4 upon drying, which would return to 0D [(PEA) 4 SnBr 6 ][(PEA)Br] 2 [CCl 2 H 2 ] 2 upon addition of dichloromethane. Powder X-ray diffraction results confirmed the reversible transformation between 0D and 2D structures. Density functional theory calculations showed that excitons in 0D [(PEA) 4 SnBr 6 ][(PEA)Br] 2 [CCl 2 H 2 ] 2 are highly localized, resulting in a strongly Stokes shifted broadband emission, while delocalized electronic states in 2D (PEA) 2 SnBr 4 result in weaker exciton binding, a higher exciton mobility, and a higher nonradiative decay.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Phenomenological mechanisms of hybrid organic–inorganic perovskite thin film deposition by RIR-MAPLE

Resonant infrared, matrix-assisted pulsed laser evaporation (RIR-MAPLE) is a promising technique for the physical vapor deposition of hybrid organic–inorganic perovskites. The approach already has been used to deposit both three-dimensional and two-dimensional hybrid perovskites with material quality comparable to those synthesized by solution processing. However, the phenomenological mechanisms of hybrid perovskite film formation by RIR-MAPLE have not been articulated. Therefore, this work presents a careful investigation of film formation mechanisms of three-dimensional methylammonium lead halide perovskites by considering the temporal evolution of morphology, crystallinity, and optical properties of films deposited by RIR-MAPLE.

Barraza, E. T. (ORCID:0000000328681496)↗
DOE OSTI2026

Chirality Transfer to the Magnetic Sublattice in the Hybrid Perovskite (R)-/(S)-3-Fluoropyrrolidinium Copper(II) Chloride

Incorporating chiral organic cations into organic–inorganic hybrid materials has been shown to enable the inorganic sublattice to display chiroptical properties. We report a new two-dimensional magnetic (S = 1/2) chiral metal halide perovskite, (R)- and (S)-(C 4 H 9 FN) 2 CuCl 4 (where (C 4 H 9 FN) + is 3-fluoropyrrolidinium), which consists of Cu–Cl inorganic layers separated by (C 4 H 9 FN) + organic cations. The presence of the chiral (C 4 H 9 FN) + organic cation induces the formation of chiral magnetic order, even though the inorganic sublattice itself is nearly structurally centrosymmetric. We also report the racemic variant, containing an equal amount of (R)- and (S)- cations, which shows no evidence of chiral magnetic order. When the magnetic susceptibility is measured perpendicular to the inorganic Cu–Cl layer propagation direction, an antiferromagnetic phase transition at Néel temperature T N = 2.23 K is observed in both the chiral and racemic materials, and the existence of the magnetic phase transition is supported by specific heat capacity measurements. Field-induced magnetic chirality is observed through the existence of a second-order magnetoelectric effect in the chiral variant, while no magnetoelectric signal is observed for the racemic material, indicating the absence of magnetic chirality. Our findings demonstrate that materials exhibiting chiral magnetic order can be created through the incorporation of a chiral cation into an organic–inorganic hybrid magnetic material, potentially allowing for the design of tailored materials that combine chiral magnetism with other desirable optical and electronic properties that come from structural chirality.

Cations↗
DOE OSTI2020

Coherent band-edge oscillations and dynamic longitudinal-optical phonon mode splitting as evidence for polarons in perovskites

The coherence of collective modes, such as phonons and polarons, and their modulation of electronic states is long sought in complex systems, which is a crosscutting issue in photovoltaics and quantum electronics. In photovoltaic cells and lasers based on metal halide perovskites, the presence of polarons, i.e., photocarriers dressed by the macroscopic motion of charged lattice, assisted by terahertz (THz) longitudinal-optical (LO) phonons, has been intensely studied yet is still debated. This may be key for explaining the remarkable properties of the perovskite materials, e.g., defect tolerance, long charge lifetimes, and diffusion lengths. In this work we use the intense single-cycle THz pulse with peak electric field up to E THz = 1000 kV/cm to drive coherent polaronic band-edge oscillations at room temperature in CH 3 NH 3 PbI 3 (MAPbI 3 ). We reveal the oscillatory behavior is dominated by a specific quantized lattice vibration mode at $ω$ LO ~ 4 THz, which is both dipole and momentum forbidden. THz-driven coherent polaron dynamics exhibits distinguishing features: room temperature coherent oscillations at ω LO longer than 1 ps in both single crystals and thin films, mode-selective modulation of different band-edge states assisted by electron-phonon interaction, and dynamic mode splitting at low temperature due to entropy and anharmonicity of organic cations. Our results demonstrate intense THz-driven coherent band-edge modulation is a powerful probe of electron-lattice coupling phenomena and polaronic quantum control in perovskites.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Reducing Non-Radiative Recombination in Perovskite Solar Cells with a SiO2-Graphene Oxide Buried Interface Layer

Perovskite solar cells (PSCs) have emerged as a transformative photovoltaic technology. However, the device performance of inverted PSCs is dramatically limited by surface defects and the underlying film morphology of metal halide perovskite (MHP) thin film. Herein, we report a novel buried interface layer consisting of SiO2 nanoparticles (NPs) chemically bonded to graphene oxide (GO), deposited atop a hydrophobic hole extraction layer (HEL) to address this limitation. The SiO2 NPs serve as insoluble scaffolds that immobilize GO sheets on the hydrophobic HEL surface, enabling the formation of homogeneous MHP thin films. Meanwhile, the GO functional groups interact with surface-uncoordinated Pb2+, suppressing interfacial defects and guiding crystal grain growth of the resultant MHP thin films. This synergistic effect suppresses non-radiative charge recombination and enhances charge extraction efficiency. As a result, a 26.07% efficiency with significantly suppressed photocurrent hysteresis is observed from PSCs incorporating the SiO2-GO buried interface layer. Moreover, the above PSCs maintain 92% of their initial PCE after 1800 h of continuous operation at the maximum power point under AM 1.5 G (100 mW/cm2) illumination at 25 degrees C in air with 50-60% relative humidity. These results demonstrate that we have developed a facile and effective way to realize high-performance inverted PSCs.

14 SOLAR ENERGY↗
DOE OSTI2026

Supramolecular assembly of molecular wires alternating crown ethers and metal–halide complexes

Metal–halide complexes serve as key emissive centres in halide perovskites; however, precise control over their spatial organization through bottom-up assembly is challenging. Here we show that a crown-ether-assisted supramolecular assembly strategy can alternatingly connect metal–halide complexes and (crown ether@A) 2+ (where ‘A’ is an alkaline earth metal cation) complexes into a one-dimensional molecular wire, which can then be packed into a hexagonal crystal structure. This process resulted in the creation of an (18C6@Ba)MnBr 4 single crystal with green emission, achieving over 80% photoluminescence quantum yield and a narrow full width at half maximum. In addition, the non-centrosymmetric crystal structure gave rise to strong nonlinear optical responses, including second-harmonic generation. This versatile supramolecular assembly approach could be generalized to create various [M(I)X 2 ] − , [M(I)X 3 ] 2− , [M(II)X 4 ] 2− and [M(III)X 5 ] 2− molecular wires, broadening the potential for diverse emission colours and distinct optical properties. This strategy provides a general design principle for constructing supramolecular metal–halide building blocks with diverse optical functionalities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Mosaic Cu I −Cu II −In III 2D Perovskites: Pressure‐Dependence of the Intervalence Charge Transfer and a Mechanochemical Alloying Method

Abstract The perovskite (BA) 4 [Cu II (Cu I In III ) 0.5 ]Cl 8 ( 1 BA ; BA + =butylammonium) allows us to study the high‐pressure structural, optical, and transport properties of a mixed‐valence 2D perovskite. Compressing 1 BA reduces the onset energy of Cu I/II intervalence charge transfer from 1.2 eV at ambient pressure to 0.2 eV at 21 GPa. The electronic conductivity of 1 BA increases by 4 orders of magnitude upon compression to 20 GPa, when the activation energy for conduction decreases to 0.16 eV. In contrast, Cu II perovskites achieve similar conductivity at ≈50 GPa. The solution‐state synthesis of these perovskites is complicated, with more undesirable side products likely from the precursor mixtures containing three different metal ions. To circumvent this problem, we demonstrate an efficient mechanochemical synthesis to expand this family of halide perovskites with complex composition by simply pulverizing together powders of 2D Cu II single perovskites and Cu I In III double perovskites.

Li, Jiayi↗
DOE OSTI2026

Research and Development Related to the Commercialization of Perovskite Radiation Detectors (CRADA Final Report)

This work will focus on the development of perovskite radiation detectors fabricated with nanocrystal, thick polycrystalline films, or single crystal materials. This will harness NREL’s instrumentation and expertise in a variety of research areas including but not limited to metal halide perovskites, device characterization, device packaging, accelerated lifetime testing, and ink chemistry development.

14 SOLAR ENERGY↗
DOE OSTI2023

Mosaic Cu I –Cu II –In III 2D Perovskites: Pressure–Dependence of the Intervalence Charge Transfer and a Mechanochemical Alloying Method

The perovskite (BA) 4 [Cu II (Cu I In III ) 0.5 ]Cl 8 (1 BA ; BA + =butylammonium) allows us to study the high-pressure structural, optical, and transport properties of a mixed-valence 2D perovskite. Compressing 1 BA reduces the onset energy of Cu I/II intervalence charge transfer from 1.2 eV at ambient pressure to 0.2 eV at 21 GPa. The electronic conductivity of 1 BA increases by 4 orders of magnitude upon compression to 20 GPa, when the activation energy for conduction decreases to 0.16 eV. In contrast, Cu II perovskites achieve similar conductivity at ≈50 GPa. The solution-state synthesis of these perovskites is complicated, with more undesirable side products likely from the precursor mixtures containing three different metal ions. Finally, to circumvent this problem, we demonstrate an efficient mechanochemical synthesis to expand this family of halide perovskites with complex composition by simply pulverizing together powders of 2D Cu II single perovskites and Cu I In III double perovskites.

2D perovskite↗
DOE OSTI2021

Perovskite on Silicon Tandem Solar Cells

Since installing solar panels costs more than the panels themselves, it is critically important to improve the efficiency of the panels so that fewer panels need to be installed. More than 90% of all panels being manufactured are made with silicon solar cells. The most promising approach to reach 27% is to upgrade the panels by adding a second set of cells with a larger band gap that can harvest the higher energy photons in the visible spectrum and generate a higher voltage than silicon is capable of generating. Perovskite semiconductors are very promising for low-cost tandems because they have high band gaps, can be rapidly printed from solutions and have been used to make 25% efficient cells by themselves. If we show that it is possible to make stable tandems with 30% efficiency using materials that could be deposited at low cost and that the energy yield will not be compromised, then private companies would be able to raise the capital needed to manufacture this technology. The main metrics for this project are the power conversion efficiency of a lab-scale perovskite/silicon tandem and the ability to maintain a high power conversion efficiency in perovskite solar cells after accelerated operational stability testing under maximum power point at elevated temperature and 1 sun illumination. In short, this project demonstrates improvements to the perovskite absorber layer, contacts for the perovskite solar cell, and transparent oxide layers for window electrodes to achieve tandem efficiencies of 25% after one year and 27% after two years. By the end of the project, we identify strategies to further improve light management in the tandem devices and outline a pathway to reach 30%.In parallel, stability testing is conducted to evaluate said absorber and contact layers in the perovskite top cell, demonstrating 1000 hours of operation with less than 10% degradation at 1 sun. Our work on this project has made a leading impact on the development of perovskite/silicon tandems. The triple halide perovskite that we developed using iodide, bromide, and chloride and published in Science in March 2020 has received significant interest from other experts in the field at conferences. We took a silicon bottom cell with 21% efficiency, a technology that is responsible for a $30 billion market, and improved it by 30% relative. In addition, we have demonstrated impressive stability of our perovskite semitransparent top cells used in the tandems, showing for the first time packaged devices that pass a variety of IEC stability tests including damp heat, temperature cycling, and UV exposure tests.

14 SOLAR ENERGY↗
DOE OSTI2022

Tolerance Factor for Stabilizing 3D Hybrid Halide Perovskitoids Using Linear Diammonium Cations

Three-dimensional (3D) halide perovskites have attracted enormous research interest, but the choice of the A-site cations is limited by the Goldschmidt tolerance factor. In order to accommodate cations that lie outside the acceptable range of the tolerance factor, low-dimensional structures usually form. To maintain the favorable 3D connection, the links among the metal-halide octahedra need to be rearranged to fit the large cations. This can result in a departure from the proper corner-sharing perovskite architectures and lead to distinctly different perovskitoid motifs with edge- and face-sharing. In this work, we report four new 3D bromide perovskitoids incorporating linear organic diammonium cations, A'Pb 2 Br 6 (A' is a +2 cation). We propose a rule that can guide the further expansion of this class of compounds, analogous to the notion of Goldschmidt tolerance factor widely adopted for 3D AMX 3 perovskites. The fundamental building blocks in A'Pb 2 Br 6 consist of two edge-shared octahedra, which are then connected by corner-sharing to form a 3D network. Different compounds adopt different structural motifs, which can be transformed from one to another by symmetry operations. Electronic structure calculations suggest that they are direct bandgap semiconductors, with relatively large band dispersions created by octahedra connected by corner-sharing. They exhibit similar electronic band structures and dynamic lattice characteristics to the regular 3D AMX 3 perovskites. Structures with smaller Pb–Br–Pb angles and larger octahedra distortion exhibit broad photoluminescence at room temperature. Furthermore, the emerging structure–property relationships in these 3D perovskitoids set the foundation for designing and investigating these compounds for a variety of optoelectronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Lamination of >21% Efficient Perovskite Solar Cells with Independent Process Control of Transport Layers and Interfaces

Transport layer and interface optimization is critical for improving the performance and stability of perovskite solar cells (PSCs) but is restricted by the conventional fabrication approach of sequential layer deposition. While the bottom transport layer is processed with minimum constraints, the narrow thermal and chemical stability window of the halide perovskite (HP) layer severely restricts the choice of top transport layer and its processing conditions. To overcome these limitations, we demonstrate lamination of HPs—where two transport layer-perovskite half-stacks are independently processed and diffusion-bonded at the HP-HP interface—as an alternative fabrication strategy that enables self-encapsulated solar cells. Power conversion efficiencies (PCE) of >21% are realized using cells that incorporate a novel transport layer combination along with dual-interface passivation via self-assembled monolayers, both of which are uniquely enabled by the lamination approach. This is the highest reported PCE for any laminated PSC encapsulated between glass substrates. We further show that this approach expands the processing window beyond traditional fabrication processes and is adaptable for different transport layer compositions. The laminated PSCs retained >75% of their initial PCE after 1000 h of 1-sun illumination at 40 °C in air using an all-inorganic transport layer configuration without additional encapsulation. Furthermore, a laminated 1 cm 2 device maintained a V oc of 1.16 V. Finally, the scalable lamination strategy in this study enables the implementation of new transport layers and interfacial engineering approaches for improving performance and stability.

14 SOLAR ENERGY↗
DOE OSTI2022

Carrier control in Sn–Pb perovskites via 2D cation engineering for all-perovskite tandem solar cells with improved efficiency and stability

All-perovskite tandem solar cells are promising for achieving photovoltaics with power conversion efficiencies above the detailed balance limit of single-junction cells, while retaining the low cost, light weight and other advantages associated with metal halide perovskite photovoltaics. However, the efficiency and stability of all-perovskite tandem cells are limited by the Sn-Pb-based narrow-bandgap perovskite cells. Here we show that the formation of quasi-two-dimensional (quasi-2D) structure (PEA) 2 GAPb 2 I 7 from additives based on mixed bulky organic cations phenethylammonium (PEA+) and guanidinium (GA+) provides critical defect control to substantially improve the structural and optoelectronic properties of the narrow-bandgap (1.25 eV) Sn-Pb perovskite thin films. Additionally, this 2D additive engineering results in Sn-Pb-based absorbers with low dark carrier density (~1.3 x 10 14 cm -3 ), long bulk carrier lifetime (~9.2 us) and low surface recombination velocity (~1.4 cm s -1 ), leading to 22.1%-efficient single-junction Sn-Pb perovskite cells and 25.5%-efficient all-perovskite two-terminal tandems with high photovoltage and long operational stability.

14 SOLAR ENERGY↗