Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fracturing materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Elastic Properties and Fracture Behaviors of Biaxially Deformed, Polymorphic MoTe 2

Biaxial deformation of suspended membranes widely exists and is used in nanoindentation to probe elastic properties of structurally isotropic two-dimensional (2D) materials. However, the elastic properties and, in particular, the fracture behaviors of anisotropic 2D materials remain largely unclarified in the case of biaxial deformation. MoTe 2 is a polymorphic 2D material with both isotropic (2H) and anisotropic (1T' and T d ) phases and, therefore, an ideal system of single-stoichiometric materials with which to study these critical issues. Here, we report the elastic properties and fracture behaviors of biaxially deformed, polymorphic MoTe 2 by combining temperature-variant nanoindentation and first-principles calculations. It is found that due to similar atomic bonding, the effective moduli of the three phases deviate by less than 15%. However, the breaking strengths of distorted 1T' and T d phases are only half the value of 2H phase due to their uneven distribution of bonding strengths. Fractures of both isotropic 2H and anisotropic 1T' phases obey the theorem of minimum energy, forming triangular and linear fracture patterns, respectively, along the orientations parallel to Mo–Mo zigzag chains. Furthermore, our findings not only provide a reference database for the elastic behaviors of versatile MoTe 2 phases but also illuminate a general strategy for the mechanical investigation of any isotropic and anisotropic 2D materials.

36 MATERIALS SCIENCE↗

Wellbore cement fracture evolution at the cement–basalt caprock interface during geologic carbon sequestration

Composite Portland cement-basalt caprock cores with fractures, as well as neat Portland cement columns, were prepared to understand the geochemical and geomechanical effects on the integrity of wellbores with defects during geologic carbon sequestration. The samples were reacted with CO2-saturated groundwater at 50 ºC and 10 MPa for 3 months under static conditions, while one cement-basalt core was subjected to mechanical stress at 2.7 MPa before the CO2 reaction. Micro-XRD and SEM-EDS data collected along the cement-basalt interface after 3-month reaction with CO2-saturated groundwater indicate that carbonation of cement matrix was extensive with the precipitation of calcite, aragonite, and vaterite, whereas the alteration of basalt caprock was minor. X-ray microtomography (XMT) provided three-dimensional (3-D) visualization of the opening and interconnection of cement fractures due to mechanical stress. Computational fluid dynamics (CFD) modeling further revealed that this stress led to the increase in fluid flow and hence permeability. After the CO2-reaction, XMT images displayed that calcium carbonate precipitation occurred extensively within the fractures in the cement matrix, but only partially along the fracture located at the cement-basalt interface. The 3-D visualization and CFD modeling also showed that the precipitation of calcium carbonate within the cement fractures after the CO2-reaction resulted in the disconnection of cement fractures and permeability decrease. The permeability calculated based on CFD modeling was in agreement with the experimentally determined permeability. This study demonstrates that XMT imaging coupled with CFD modeling represent a powerful tool to visualize and quantify fracture evolution and permeability change in geologic materials and to predict their behavior during geologic carbon sequestration or hydraulic fracturing for shale gas production and enhanced geothermal systems.

basalt↗

Finite Element Simulation of Machining of Ti6Al4V Alloy

Titanium and its alloys are an important class of materials, especially for aerospace applications, due to their excellent combination of strength and fracture toughness as well as low density. However, these materials are generally regarded as difficult to machine because of their low thermal conductivity and high chemical reactivity with cutting tool materials. Moreover, the low thermal conductivity of Titanium inhibits dissipation of heat within the workpiece causing an higher temperature at the cutting edge and generating for higher cutting speed a rapid chipping at the cutting edge which leads to catastrophic failure. In addition, chip morphology significantly influences the thermo-mechanical behaviour at the workpiece/tool interface, which also affects the tool life.In this paper a finite element analysis of machining of TiAl6V4 is presented. In particular, cutting force, chip morphology and segmentation are taken into account due to their predominant roles to determine machinability and tool wear during the machining of these alloys. Results in terms of residual stresses are also presented. Moreover, the numerical results are compared with experimental ones.

36 MATERIALS SCIENCE↗

A macro-micro approach for identifying crystal plasticity parameters for necking and failure in nickel-based alloy haynes 282

Here, this work develops a two-scales macro-micro approach to address the challenge in calibrating crystal plasticity microstructural models when samples undergo necking prior to fracture. The crystal plasticity models are crucial for predicting the materials’ plastic deformation and failure at the microstructure level, identifying the materials’ intrinsic properties as well as investigating the microstructure-properties relationships. However, after necking occurs, the experimentally measured stress-strain curves fail to reflect the materials ‘true’ stress-strain behavior and cannot be directly fitted into crystal plasticity models. The proposed macro-micro approach employs a top-down strategy to address this challenge, which has been studied with experimental tests on precipitation-strengthened Ni-based superalloy Haynes® 282®. In this approach, a macro rate-dependent anisotropic plasticity model with Voce-type hardening and Rice-Tracey damage law is first utilized to model the deformation and failure of the tensile bar, and calibrated by matching the stress-strain curves, necking strain, and reduction of area. Especially, to match the testing results under different applied strain rates, the rate-sensitivity parameter m and saturation stress in the elasticity model are modified to incorporate dependence on the local strain rate. Then, the ‘true’ stress-strain behaviors are extracted from the necking zone of the macro-model, which are used to calibrate a micro-model with explicit microstructures and governed by an extended crystal plasticity law. The consistency between the micro-model and macro-model are enforced during calibration. The calibration outcomes from the crystal plasticity model elucidate the materials intrinsic properties for slip, hardening, and failure, which is vital for further investigations into the microstructure-properties relationship and for accurate prediction of the material behavior under various test and service conditions.

36 MATERIALS SCIENCE↗

In situ X-ray imaging of heterogeneity in dynamic compaction of granular media

Dynamic compaction of granular materials is a complex process wherein the material response at the continuum scale arises from fracture, comminution, and fragment ow at the grain scale. Granular materials have heterogeneity due to variation in grain properties, as well as variation in local packing density and structure. These heterogeneities may affect the dynamic compaction response, producing a structured and time-varying compaction front. Methodology used to characterize the shock behavior in solid materials may be inappropriate for granular materials, because of this unsteady behavior and interactions between the granular material and measurement surfaces. To observe the compaction front heterogeneity, in-situ x-ray imaging of granular compaction is conducted at a scale between the grain- and continuum scales. To allow for sufficient x-ray transmission, a thin sample geometry is used, for which boundary affects may result in a significantly different load path than would occur in a 1-D compaction configuration. Numerical simulations of the experimental geometry support analysis of the results so that the feature of the compaction front can be distinguished from artifacts of the experimental configuration. The results suggest compaction front heterogeneity may have structure with a length scale of tens of particle diameters, and demonstrate that finite grain size can inhibit the formation shear-induced features that would arise in a homogenized representation of the same material.

36 MATERIALS SCIENCE↗

Three-Dimensional Modeling of Fracture Clusters in Geothermal Reservoirs

The objective of this is to develop a 3-D numerical model for simulating mode I, II, and III (tensile, shear, and out-of-plane) propagation of multiple fractures and fracture clusters to accurately predict geothermal reservoir stimulation using the virtual multi-dimensional internal bond (VMIB). Effective development of enhanced geothermal systems can significantly benefit from improved modeling of hydraulic fracturing. In geothermal reservoirs, where the temperature can reach or exceed 350oC, thermal and poro-mechanical processes play an important role in fracture initiation and propagation. In this project hydraulic fracturing of hot subsurface rock mass will be numerically modeled by extending the virtual multiple internal bond theory and implementing it in a finite element code, WARP3D, a three-dimensional finite element code for solid mechanics. The new constitutive model along with the poro-thermoelastic computational algorithms will allow modeling the initiation and propagation of clusters of fractures, and extension of pre-existing fractures. The work will enable the industry to realistically model stimulation of geothermal reservoirs. The project addresses the Geothermal Technologies Office objective of accurately predicting geothermal reservoir stimulation (GTO technology priority item). The project goal will be attained by: (i) development of the VMIB method for application to 3D analysis of fracture clusters; (ii) development of poro- and thermoelastic material sub-routines for use in 3D finite element code WARP3D; (iii) implementation of VMIB and the new material routines in WARP3D to enable simulation of clusters of fractures while accounting for the effects of the pore pressure, thermal stress and inelastic deformation; (iv) simulation of 3D fracture propagation and coalescence and formation of clusters, and comparison with laboratory compression tests; and (v) application of the model to interpretation of injection experiments (planned by our industrial partner) with reference to the impact of the variations in injection rate and temperature, rock properties, and in-situ stress.

15 GEOTHERMAL ENERGY↗

Compliance and stress intensity coefficients for short bar specimens with chevron notches

For the determination of fracture toughness especially with brittle materials, a short bar specimen with rectangular cross section and chevron notch can be used. As the crack propagates from the tip of the triangular notch, the load increases to a maximum then decreases. To obtain the relation between the fracture toughness and maximum load, calculations of Srawley and Gross for specimens with a straight-through crack were applied to the specimens with chevron notches. For the specimens with a straight-through crack, an analytical expression was obtained. This expression was used for the calculation of the fracture toughness versus maximum load relation under the assumption that the change of the compliance with crack length for the specimen with a chevron notch is the same as for a specimen with a straight-through crack.

Munz, D.↗

Reliability of structural brittle materials

Traditionally, the use of brittle materials has been avoided in demanding structural applications because of their unreliability. They have been used however, due to other desirable properties, in nonstructural applications or where the mechanical load is minimal. The most common method utilized today for the design approach of brittle materials is the probabilistic, which takes into consideration the flaw and stress distribution within the brittle material. It does not take into consideration the fracture mechanics effect of strength degradation while aging under a mechanical load. This project will combine the two methods, probabilistic and fracture mechanics, into a more reliable design method for brittle materials.

Hall, W. B.↗

Steels For Rolling-Element Bearings

Bearing lives increased by attention to details of processing and applications. NASA technical memorandum discusses selection of steels for long-life rolling-element bearings. After brief review of advances in manufacturing, report discusses effect of cleanliness of bearing material on fatigue in rolling element. Also discusses fracture toughnesses of through-hardened and case-hardened materials.

Zaretsky, Erwin V.↗

Fatigue Properties of Ti-6Al-4V Titanium Alloy Friction Stir Welding Joint

Friction stir welding was used to consolidate 2-mm-thick Ti-6Al-4V titanium alloy sheets, and the static and fatigue properties of the joint were investigated. The results reveal that uniform microhardness distribution of the nugget zone (NZ) after post-weld heat treatment was associated with the uniform equiaxed microstructure of the NZ. The joint fatigue limit predicted by the S–N curve reached 640.84 MPa, up to 64.76% of joint tensile strength. Fatigue specimens fractured at the transition zone between the base material and NZ, and the positions of fatigue crack initiation sites were relatively random. The fracture surface of the fatigue crack propagation region was composed of radial strips and striations, and numerous dimples were observed on the final fast fracture surface.

36 MATERIALS SCIENCE↗

Analyses of Buckling and Stable Tearing in Thin-Sheet Materials

This paper was to verify the STAGS (general shell, geometric and material nonlinear) code and the critical crack tip opening angle (CTOA) fracture criterion for predicting stable tearing in cracked panels that fail with severe out of plane buckling. Materials considered ranged from brittle to ductile behavior. Test data used in this study are reported elsewhere. The STAGS code was used to model stable tearing using a critical CTOA value that was determined from a cracked panel that was 'restrained' from buckling. ne analysis methodology was then used to predict the influence of buckling on stable tearing and failure loads. Parameters like crack length to specimen width ratio, crack configuration, thickness, and material tensile properties had a significant influence on the buckling behavior of cracked thin sheet materials. Experimental and predicted results showed a varied buckling response for different crack length to sheet thickness ratios because different buckling modes were activated. Effects of material tensile properties and fracture toughness on buckling response were presented. The STAGS code and the CTOA fracture criterion were able to predict the influence of buckling on stable tearing behavior and failure loads on a variety of materials and crack configurations.

Seshadri, B. R.↗

Composites structures for bone tissue reconstruction

The search for new biomaterials in the bone reconstitution field is growing continuously as humane life expectation and bone fractures increase. For this purpose, composite materials with biodegradable polymers and hydroxyapatite (HA) have been used. A composite material formed by a film, nanofibers and HA has been made. Both, the films and the non-woven mats of nanofibers were formed by nanocomposites made of butylene adipate-co-terephthalate (PBAT) and HA. The techniques used to produce the films and nanofibers were spin coating and electrospinning, respectively. The composite production and morphology were evaluated. The composite showed an adequate morphology and fibers size to be used as scaffold for cell growth.

36 MATERIALS SCIENCE↗

Atomistic models for scintillator discovery.

A2BLnX6 elpasolites (A, B: alkali; Ln: lanthanide; X: halogen), LaBr3 lanthanum bromide, and AX alkali halides are three classes of the ionic compound crystals being explored for {gamma}-ray detection applications. Elpasolites are attractive because they can be optimized from combinations of four different elements. One design goal is to create cubic crystals that have isotropic optical properties and can be grown into large crystals at lower costs. Unfortunately, many elpasolites do not have cubic crystals and the experimental trial-and-error approach to find the cubic elpasolites has been prolonged and inefficient. LaBr3 is attractive due to its established good scintillation properties. The problem is that this brittle material is not only prone to fracture during services, but also difficult to grow into large crystals resulting in high production cost. Unfortunately, it is not always clear how to strengthen LaBr3 due to the lack of understanding of its fracture mechanisms. The problem with alkali halides is that their properties decay rapidly over time especially under harsh environment. Here we describe our recent progress on the development of atomistic models that may begin to enable the prediction of crystal structures and the study of fracture mechanisms of multi-element compounds.

36 MATERIALS SCIENCE↗

Modelling deformation and fracture in confectionery wafers

The aim of this research is to model the deformation and fracture behaviour of brittle wafers often used in chocolate confectionary products. Three point bending and compression experiments were performed on beam and circular disc samples respectively to determine the 'apparent' stress-strain curves in bending and compression. The deformation of the wafer for both these testing types was observed in-situ within an SEM. The wafer is modeled analytically and numerically as a composite material with a core which is more porous than the skins. X-ray tomography was used to generate a three dimensional volume of the wafer microstructure which was then meshed and used for quantitative analysis. A linear elastic material model, with a damage function and element deletion, was used and the XMT generated architecture was loaded in compression. The output from the FE simulations correlates closely to the load-deflection deformation observed experimentally.

36 MATERIALS SCIENCE↗

Surface and subsurface cracks characteristics of single crystal SiC wafer in surface machining

Different machining processes were used in the single crystal SiC wafer machining. SEM was used to observe the surface morphology and a cross-sectional cleavages microscopy method was used for subsurface cracks detection. Surface and subsurface cracks characteristics of single crystal SiC wafer in abrasive machining were analysed. The results show that the surface and subsurface cracks system of single crystal SiC wafer in abrasive machining including radial crack, lateral crack and the median crack. In lapping process, material removal is dominated by brittle removal. Lots of chipping pits were found on the lapping surface. With the particle size becomes smaller, the surface roughness and subsurface crack depth decreases. When the particle size was changed to 1.5µm, the surface roughness Ra was reduced to 24.0nm and the maximum subsurface crack was 1.2µm. The efficiency of grinding is higher than lapping. Plastic removal can be achieved by changing the process parameters. Material removal was mostly in brittle fracture when grinding with 325# diamond wheel. Plow scratches and chipping pits were found on the ground surface. The surface roughness Ra was 17.7nm and maximum subsurface crack depth was 5.8 µm. When grinding with 8000# diamond wheel, the material removal was in plastic flow. Plastic scratches were found on the surface. A smooth surface of roughness Ra 2.5nm without any subsurface cracks was obtained. Atomic scale removal was possible in cluster magnetorheological finishing with diamond abrasive size of 0.5 µm. A super smooth surface eventually obtained with a roughness of Ra 0.4nm without any subsurface crack.

36 MATERIALS SCIENCE↗

Ball-on-ring test validation for equibiaxial flexural strength testing of engineered ceramics

The validation of a ball-on-ring, equibiaxial flexural strength method to obtain the transverse rupture strength (TRS) of right cylindrical ceramic specimens was performed in this study. Validation of the test method was achieved using commercially available engineered high purity alumina disks and finite element (FE) model analysis. The validated fixture was then used to obtain the TRS and Weibull statistical analysis of MgO-partially stabilized zirconia (MSZ) and Y 2 O 3 -partially stabilized zirconia (YSZ) ceramic disks. TRS data for alumina, MSZ, and YSZ agreed with the TRS values reported in the literature. A statistically relevant number of samples (N > 30) for each material were tested to allow for a Weibull statistical analysis. Weibull parameters for these materials were within the expected values for engineered ceramics. The characteristic strength for alumina, MSZ, and YSZ were determined to be 289, 786, and 814 MPa, respectively. The Weibull modulus was determined between 10 and 25 for each material, which is typical of engineered ceramics. In addition, FE model results were in close agreement with experimental fracture values for the three ceramic materials tested in this study.

36 MATERIALS SCIENCE↗

Martian fluidized crater morphology - Variations with crater size, latitude, altitude, and target material

The paper investigates the influence of crater latitude, target material, and elevation on the morphology of the ejecta facies and crater interiors as a function of crater diameter. It is shown that only pancake craters exhibit latitudinal variation in their distribution. It is also shown that several crater types are associated with specific target materials: radial textured craters are found primarily on Tharsis and Elysium lavas, and pancake craters are found on fractured terrain, old lavas, and channel materials. Craters formed on recent lavas more frequently possess secondary craters, central peaks, and terraces than primary craters found on other geological units. The maximum radial extent of fluidized ejecta is demonstrated to be a function of crater altitude and latitude.

Mouginis-Mark, P.↗