Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electronic component”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Microdensitometer electronics modification

Minor modifications of electronic components in the PDS 1010A microdensitometer are discussed. The operational requirements and performance limitations of the PDS are noted. Replacement of the photomultiplier and front-end analog circuitry significantly improved the photometric performance of the PDS. The improvement in density repeatability is marked, and the permissible density slew speed is greatly increased.

Hewitt, A. V.↗

Contamination Measurements During Ius Thermal Vacuum Tests in A Large Space Chamber

The levels of contamination that originate from inside the IUS equipment support section (ESS) due to outgassing from electronics components and wiring operating at elevated temperatures (80-160 F) were investigated. Pressure was measured inside and outside the ESS. Mass deposition measurements were made with quartz crystal microbalances (QCM) facing into and away from ESS vents. The OCM's were operated at -50 C and -180 C using thermoelectrically and cryogenically cooled QCM's. Gaseous nitrogen flow inside the ESS was used to obtain the effective molecular flow vent area of the ESS, which was evaluated to be 359 sq cm (56 sq in) compared to the 978 sq cm (150 sq in) estimated by an earlier atmosphere pressure billowing test. The total outgassing rate of the ESS materials at a temperature of 60 C (140 F) decays with a time constant of 11.5 hours based on pressure measurements during the hot cycle. A time constant of 22 hours was estimated for the fraction of the outgassing which will condense on a -50 C surface. In contrast, the time constant is only 10.1 hours for the outgassing material which condenses on a surface at -180 C. A surface at -180 C collects approximately one half of the material vented from the ESS which impinges on it. Pressure measurements show very good correlation with the mass deposition measurements.

C R Mullen↗

The effect of direct and reflected radiation on the temperatures of space structures

As an orbiting structure passes from the bright side to the dark side of the earth, substantial differences in surface heating may take place due to direct sunlight and albedo. Most structures are built of convex curved elements to spread out the reflected energy. A change in the shortwave absorptivity and emissivity maintains the temperature of electronic components within a narrow range. Temperature extremes may also be reduced by the use of thermal capacity of the system or by shielding the surface from direct sunlight. For an instrument deployed from a Shuttle, a temperature must be established for it in the cargo bay before deployment. The effect of obstructed views by surfaces such as the Shuttle arm complicates solar flux computations because of the object's mobility. For typical orbits, the earth's albedo and the direct long wavelength radiation may be as much as 30 percent of the direct solar flux. Irradiation due to direct and reflected solar, long wave radiation and reflected radiation from earth, and from Shuttle surfaces is largely dependent on the specular reflection from the radiators as the Shuttle rolls and its surfaces block the sun. Through a judicious choice of surface properties, thermal capacitance and orbit attitude programming, the temperature response of a system can be controlled.

Emery, A. F.↗

Stimulated Raman up-conversion of electromagnetic waves by a gyrating electron beam

A gyrating electron beam supports negative energy modes near the harmonics of electron-cyclotron frequency. An electromagnetic wave passing through such a beam parametrically up-converts into high-frequency electromagnetic modes separated from the pump frequency by the electron-cyclotron harmonics. The growth rate for this process varies directly as the oscillatory velocity of beam electrons caused by the pump and as square root of the beam density. It has a maximum at values of scattering angle close to 180 deg and is also implicitly dependent on the beam veocity and the cyclotron frequency of electrons. The effect of a cold electron component is to reduce the growth rate.

Sharma, O. P.↗

The secondary radiation under Saturn's A-B-C rings produced by cosmic ray interactions

On the basis of a study of spacecraft data of Saturn, Chenette et al. (1980) concluded that highly relativistic galactic cosmic ray nuclei with magnetic rigidities greater than the Stoermer rigidity cutoff in the plane of Saturn's A-B-C rings along the Pioneer 11 trajectory produced a secondary population of charged particles. The existence of this secondary particle population was confirmed by Randall (1982). Cooper and Simpson (1980) further developed this concept of secondary production of nucleons by cosmic ray nuclei to estimate the yield of secondary neutrons which might, through decay, populate the radiation belt with low-energy electrons and protons. Cooper (1983) reported quantitative Monte Carlo calculations of neutron production in the rings and their decay in the magnetosphere. The present investigation is concerned with a confirmation of the earlier work, and an extension of the studies on the basis of improved spectra for the proton and electron components.

Cooper, J. F.↗

Detector Arrays With Image-Plane Processing

Image detection and edge processing merged on same VLSI chip. Concept combines relatively large detector with small processor elements as VLSI chip features and has many specific embodiments. New device concept retains relatively large detector element sizes (perhaps 10 to 100 micrometers or larger in diameter) with processing-electronics components of much smaller size (2 micrometers or less), filling in gaps left between detectorelement active areas. Detector-array device helps to perform difference-ofGaussian operation for use in machine-vision edge enhancement and edge detection.

Jobson, D. J.↗

Time optimal robotic manipulator motions and work places for point to point tasks

High productivity requires that manipulators perform complex tasks quickly. Recently, optimal control algorithms have been developed which enable manipulators to move quickly, but only for simple motions. A method is presented here which combines simple time optimal motions in an optimal manner to yield the minimum time motions for an important class of complex manipulator tasks composed of point to point moves, such as assembly, electronic component insertion and spot welding. This method can also be used to design manipulator actions and work places so that tasks can be completd in minimum time. The method has been implemented in a CAD software package. Examples are presented which show the methods effectiveness.

Dubowsky, S.↗

Numerical study of the spectrum of broadband electrostatic noise in the magnetotail

A numerical study of the spectrum of broadband electrostatic noise (BEN) generated by ion beams in the plasma sheet boundary layer (PSBL) is presented, in which two cases are analyzed. The first case is concerned with a single hot-electron species. In the second case, a second population of cold electrons (arising from diffusion from the lobe into the PSBL) is introduced. The presence of the second electron component in the dispersion relation for generating BEN was found to significantly increase the upper frequency range of the unstable spectrum, enhancing the associated growth rates. It is shown that ion beam instabilities can explain most major features of the observed BEN spectrum. The results explain the gradual rise in the upper frequency range of BEN as a spacecraft approaches the plasma sheet from the lobe, and the sudden jump in that frequency up to near the plasma frequency upon crossing the PSBL.

Grabbe, Crockett L.↗

Acoustical Convective Cooling Or Heating

Small, efficient ultrasonic device circulates fluid. Vibrating at ultrasonic frequency, piezoelectric driver sets up vortexes transfering heat to or from object in space. Used on Earth to apply localized or concentrated cooling to individual electronic components or other small parts.

Trinh, Eugene H.↗

A two-fluid model for solar wind fluid with higher order moments

A spherically symmetric two-fluid model for the solar wind with higher-order moments is presented. In this model, continuity, momentum, temperature and heat flux equations for two components (electrons and protrons) in steady solar wind states are simultaneously solved by using a time-dependent method. This work is used to compare solutions of the steady-state solar wind with and without higher order moments, and to study the effects of thermal conduction. The coupling between electrons and protrons is also given special attention. The numerical solutions of the steady-state solar wind in both subsonic and supersonic regions between the Sun and 1 AU are obtained and graphically illustrated.

Wang, Jingfang↗

Optically controlled phased-array antenna technology for space communication systems

Using MMICs in phased-array applications above 20 GHz requires complex RF and control signal distribution systems. Conventional waveguide, coaxial cable, and microstrip methods are undesirable due to their high weight, high loss, limited mechanical flexibility and large volume. An attractive alternative to these transmission media, for RF and control signal distribution in MMIC phased-array antennas, is optical fiber. Presented are potential system architectures and their associated characteristics. The status of high frequency opto-electronic components needed to realize the potential system architectures is also discussed. It is concluded that an optical fiber network will reduce weight and complexity, and increase reliability and performance, but may require higher power.

Kunath, Richard R.↗

A cyclotron-maser instability associated with a nongyrotropic distribution

A stability analysis for the cyclotron-maser instability in the presence of a nongyrotropic electron distribution is presented. The model configuration describes a uniformly magnetized cold ambient plasma that contains a relatively diffuse suprathermal electron component coherently bunched in gyrophase. The stability of perturbations propagating parallel to the ambient magnetic field is considered, and substantial growth rates are found to occur. The results are contrasted with those found for a comparable gyrotropic loss-cone distribution, and it is found that the nongyrotropic instability is characterized by substantially higher growth rates.

Freund, H. P.↗

Honeycomb-Fin Heat Sink

Improved finned heat sink for electronic components more lightweight, inexpensive, and efficient. Designed for use with forced air, easily scaled up to dissipate power up to few hundred watts. Fins are internal walls of aluminum honeycomb structure. Cell structure gives strength to thin aluminum foil. Length of channels chosen for thermodynamic efficency; columns of cells combined in any reasonable number because flowing air distributed to all. Heat sink cools nearly as effectively at ends as near its center, no matter how many columns of cells combined.

Rippel, Wally E.↗

Multiple sensor smart robot hand with force control

A smart robot hand developed at JPL for the Protoflight Manipulator Arm (PFMA) is described. The development of this smart hand was based on an integrated design and subsystem architecture by considering mechanism, electronics, sensing, control, display, and operator interface in an integrated design approach. The mechanical details of this smart hand and the overall subsystem are described elsewhere. The sensing and electronics components of the JPL/PFMA smart hand are summarized and it is described in some detail in control capabilities.

Killion, Richard R.↗

The long-term effects of the micrometeoroid and orbital debris environments on materials used in space

The long-term effects of the orbital debris and micrometeoroid environments on materials that are current candidates for use on space vehicles are discussed. In addition, the limits of laboratory testing to determine these effects are defined and the need for space-based data is delineated. The impact effects discussed are divided into primary and secondary surfaces. Primary surfaces are those that are subject to erosion, pitting, the degradation and delamination of optical coatings, perforation of atomic oxygen erosion barriers, vapor coating of optics and the production of secondary ejecta particles. Secondary surfaces are those that are affected by the result of the perforation of primary surfaces, for example, vapor deposition on electronic components and other sensitive equipment, and the production of fragments with damage potential to internal pressurized elements. The material properties and applications that are required to prevent or lessen the effects described, are defined.

Cour-Palais, Burton G.↗

Some issues in numerical simulation of nonlinear structural response

The development of commercial finite element software is addressed. This software provides practical tools that are used in an astonishingly wide range of engineering applications that include critical aspects of the safety evaluation of nuclear power plants or of heavily loaded offshore structures in the hostile environments of the North Sea or the Arctic, major design activities associated with the development of airframes for high strength and minimum weight, thermal analysis of electronic components, and the design of sports equipment. In the more advanced application areas, the effectiveness of the product depends critically on the quality of the mechanics and mechanics related algorithms that are implemented. Algorithmic robustness is of primary concern. Those methods that should be chosen will maximize reliability with minimal understanding on the part of the user. Computational efficiency is also important because there are always limited resources, and hence problems that are too time consuming or costly. Finally, some areas where research work will provide new methods and improvements is discussed.

Hibbitt, H. D.↗

Optically controlled phased-array technology for space communication systems

Using MMICs in phased-array applications above 20 GHz requires complex RF and control signal distribution systems. Conventional waveguide, coaxial cable, and microstrip methods are undesirable due to their high weight, high loss, limited mechanical flexibility and large volume. An attractive alternative to these transmission media, for RF and control signal distribution in MMIC phased-array antennas, is optical fiber. Presented are potential system architectures and their associated characteristics. The status of high frequency opto-electronic components needed to realize the potential system architectures is also discussed. It is concluded that an optical fiber network will reduce weight and complexity, and increase reliability and performance, but may require higher power.

Kunath, Richard R.↗

The space radiation environment for electronics

The earth's space radiation environment is described in terms of charged particles as relevant to effects on spacecraft electronics. The nature and magnitude of the trapped and transiting environments are described in terms of spatial distribution and temporal variation. The internal radiation environment of the spacecraft is described in terms of shielding the high-energy particles of the free-field environment. Exposure levels are presented in terms of ionizing radiation dose and particle fluence for comparison to electronic component susceptibility.

Stassinopoulos, E. G.↗