SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Singular spectrum analysis was used to study global magnetospheric dynamics using time series auroral electrojet (AE) data. The calculated correlation dimension of approximately 2.5 confirms the low dimensionality of earlier results. This technique indicated that global magnetospheric dynamics can be described by three variables whose dynamical features were obtained from the AE data.
A nonlinear aerodynamic analysis technique based on the full potential equation in conservative form has been modified to permit treatment of supersonic flows with embedded subsonic regions (typically near the fuselage-canopy juncture and the wing leading edge). Solution procedures for the equations do not require any specific form of geometry or physical grid system. This results in the capability to analyze easily very complex geometries provided the posed problem lies within the isentropic restrictions of the full potential theory. Characteristic signal propagation theory is used to monitor the type dependent flow and a conservative switching scheme is employed to transition from the supersonic marching algorithm to a subsonic relaxation procedure and vice versa. An implicit approximate factorization scheme is used to solve the finite-difference equations. These modifications now permit analysis of fully three-dimensional flowfields including the interference effects due to lifting surface wakes. Improved grid generation capability allows analysis of complete complex aircraft geometries (fuselage, wing, tail, wing wake, and tail wake). Results are presented showing very good correlations with experimental surface pressure data and aerodynamic force data at both design and off-design operating points. Configurations examined include several waverider concepts, an arrow wing-body with wake, an advanced tactical fighter concept, and a fighter forebody-canard configuration.
Analysis of flutter of flat rectangular panels at low supersonic mach numbers using air forces from exact linearized potential-flow theory
Self consistent one dimensional large signal analysis of Read type IMPATT diode oscillator, taking into account device-circuit interaction
Wind velocities from 25 km to 60 km over Ascension Island, Fort Sherman and Kwajalein for the period January 1970 to December 1971 are analyzed in order to achieve a better understanding of the mean flow, the eddy kinetic energy and the Eulerian time spectra of the eddy kinetic energy. Since the data are unequally spaced in time, techniques of one-dimensional covariance theory were utilized and an unequally spaced time series analysis was accomplished. The theoretical equations for two-dimensional analysis or wavenumber frequency analysis of unequally spaced data were developed. Analysis of the turbulent winds and the average seasonal variance and eddy kinetic energy of the turbulent winds indicated that maximum total variance and energy is associated with the east-west velocity component. This is particularly true for long period seasonal waves which dominate the total energy spectrum. Additionally, there is an energy shift for the east-west component into the longer period waves with altitude increasing from 30 km to 50 km.
Numerical analysis of two-dimensional laminar flow with nonregular boundaries
The Global Positioning System (GPS) enables positioning with a very small receiver. The signals transmitted by the GPS satellites are sensitive to the atmosphere and can be used to perform soundings with the radio occultation technique (e.g., Kursinski et al., 1997). The GPS signal can be converted to refractivity N via the Abel transform. The refractivity can then be related to atmospheric pressure P, temperature T, and water vapor partial pressure P (sub w) the GPS measurement, (between 0.5 and 1.5 km), its self-calibration, and it's nearly all-weather capabilities make it a good candidate for use in data assimilation systems (DAS) and numerical weather prediction (NWP). In order to demonstrate its usefulness in a DAS or NWP system, a first step is to assess its impact oil the analysis. A one-dimensional variational off-line analysis (1DVAR), meaning the data are not assimilated 'In the 3D DAS, constitutes a starting approach to which further enhancements can be made. The chosen observable to be analyzed in this study is the refractivity. One way to extract temperature (humidity) from the refractivity, is to assume a humidity (temperature) profile. One variable may then be retrieved without any a priori information. The 1DVAR approach used here resolves the ambiguity problem raised in the interpretation of these data. It enables retrieving these two atmospheric variables at a reasonable computing cost.
CRAY 2 and CRAY Y-MP evaluation runs are undertaken for a three-dimensional, elastoplastic FEM code implementation of the 'autotasking' parallel-processing technique, which is used in all code components except the matrix-equation solver. For a typical example problem in the case of a four-processor CRAY 2, a speedup factor of 2.1 was found achievable in a dedicated environment, and 1.7 in a multiuser environment; for a three-processor CRAY Y-MP, speedup in a multiuser environment was about 2.4. Only minimal effort was required to implement autotasking in this implementation code.
An experimental investigation of the three-dimensional flow field through a low aspect ratio, transonic, axial flow fan rotor has been conducted, using an advanced laser anemometer (LA) system. Laser velocimeter measurements of the rotor flow field at the design operating speed and over a range of throughflow conditions are compared to analytical solutions. The numerical technique used herein yields the solution to the full, three-dimensional, unsteady Euler equations using an explicit time-marching, finite volume approach. The numerical analysis, when coupled with a simplified boundary layer calculation, generally yields good agreement with the experimental data. The test rotor has an aspect ratio of 1.56, a design total pressure ratio of 1.629 and a tip relative Mach number of 1.38. The high spatial resolution of the LA data matrix (9 radial x 30 axial x 50 blade-to-blade) permits details of the transonic flow field such as shock location, turning distribution, and blade loading levels to be investigated and compared to analytical results.
The application of a three-dimensional transonic flow analysis method, TRANAIR, is explored from the point of view of a user. Detailed features of the program are outlined to give a better understanding of capability. Numerous results are presented to show some of the complex configurations which have been analyzed. In particular, examples are provided which show the application to turbofan engine installation on transport aircraft.
A three-dimensional unsteady aerodynamic analysis is described for predicting the time-dependent flow about ducted and unducted propfans operating at angle of attack. Although the freestream is assumed to be uniform, the flow relative to the rotating blades varies with circumferential position, resulting in an inherent unsteadiness due to the nonaxial inflow. The time-dependent Euler equations are solved utilizing a Runge-Kutta time-stepping scheme. The analysis is based on a finite-volume discretization employing a multiple-block grid network. To permit the use of large calculation time steps, an implicit residual smoothing scheme previously tested for unsteady flow calculations in two dimensions is extended to three spatial dimensions. For unducted propfans, a single H-type grid block is used for each blade passage to determine the time-periodic flowfield. For ducted propfans (ultra-high bypass fans) a body-centered C-type grid is wrapped about the cowl to improve the accuracy of the analysis in the high gradient flow region near the cowl leading edge. Numerical results are compared with available data for both ducted and unducted propfans operating at angle of attack.
The purpose of this study is the development of a three-dimensional Euler/Navier-Stokes flow analysis for fan section/engine geometries containing multiple blade rows and multiple spanwise flow splitters. An existing procedure developed by Dr. J. J. Adamczyk and associates and the NASA Lewis Research Center was modified to accept multiple spanwise splitter geometries and simulate engine core conditions. The procedure was also modified to allow coarse parallelization of the solution algorithm. This document is a final report outlining the development and techniques used in the procedure. The numerical solution is based upon a finite volume technique with a four stage Runge-Kutta time marching procedure. Numerical dissipation is used to gain solution stability but is reduced in viscous dominated flow regions. Local time stepping and implicit residual smoothing are used to increase the rate of convergence. Multiple blade row solutions are based upon the average-passage system of equations. The numerical solutions are performed on an H-type grid system, with meshes being generated by the system (TIGG3D) developed earlier under this contract. The grid generation scheme meets the average-passage requirement of maintaining a common axisymmetric mesh for each blade row grid. The analysis was run on several geometry configurations ranging from one to five blade rows and from one to four radial flow splitters. Pure internal flow solutions were obtained as well as solutions with flow about the cowl/nacelle and various engine core flow conditions. The efficiency of the solution procedure was shown to be the same as the original analysis.
A small strain theory, three-dimensional elastic-plastic finite element analysis was used to simulate fracture in thin sheet 2024-T3 aluminum alloy in the T-L orientation. Both straight and tunneled cracks were modeled. The tunneled crack front shapes as a function of applied stress were obtained from the fracture surface of tested specimens. The stable crack growth behavior was measured at the specimen surface as a function of applied stress. The fracture simulation modeled the crack tunneling and extension as a function of applied stress. The results indicated that the global constraint factor, alpha(sub g), initially dropped during stable crack growth. After peak applied stress was achieved, alpha(sub g) began to increase slightly. The effect of crack front shape on alpha(sub g) was small, but the crack front shape did greatly influence the local constraint and through-thickness crack-tip opening angle (CTOA) behavior. The surface values of CTOA for the tunneled crack front model agreed well with experimental measurements, showing the same initial decrease from high values during the initial 3mm of crack growth at the specimen's surface. At the same time, the interior CTOA values increased from low angles. After the initial stable tearing region, the CTOA was constant through the thickness. The three-dimensional analysis appears to confirm the potential of CTOA as a two-dimensional fracture criterion.
Flow field animation is the natural choice as a tool in the analysis of the numerical simulations of complex unsteady three-dimensional flows. The PLOT4D extension of the widely used PLOT3D code to allow the interactive animation of a broad range of flow variables was developed and is presented. To allow direct comparison with unsteady experimental smoke and dye flow visualization, the code STREAKER was developed to produce time accurate streaklines. Considerations regarding the development of PLOT4D and STREAKER, and example results are presented.
A two-dimensional unsteady aerodynamic Euler solver based on a flux differencing scheme is being developed to analyze oscillating cascades. The cascades can have subsonic, transonic, or supersonic flow with either subsonic or supersonic axial velocity. The aerodynamic solver is coupled with a typical section structural model for each blade of the cascade. Flutter analysis methods both in time and frequency domains are then implemented into the resulting aeroelastic solver. Methods that reduce computational time for calculating the unsteady aerodynamic coefficients, namely the influence coefficient method and the pulse response method, are also implemented and validated. The present solver showed good correlation with published results for all the flow regimes. It is shown that grid coarsening improved the accuracy of the predictions. A representative flutter calculation showed that both the frequency domain and time domain methods are implemented correctly into the aeroelastic solver.
Techniques of finite element analysis in two dimensional plane strain were applied to problems of geophysics and tectonics. More specifically, the flexibility of the finite element method was employed to address problems involving geological complexity and fault interactions. The modeling of effective anisotropy in material elastic properties proved useful in describing the deformation of faulted crustal blocks. The applications of this modeling work to problems of actual tectonics in southern California was explored. Preliminary models show encouraging agreement with measured tectonic strain in this region, and modeling work was done to gain an understanding of the stress state in a locked fault region with future seismic potential.
A steady incompressible three-dimensional viscous flow analysis has been conducted for the Space Shuttle External Tank/Orbiter propellant feed line disconnect flapper valves with upstream elbows. The full Navier-Stokes code, INS3D, is modified to handle interior obstacles. Grids are generated by SVTGD3D code. Two dimensional initial grids in the flow cross section with and without the flappers are improved by elliptic smoothing to provide better orthogonality, clustering and smoothness to the three dimensional grid. The flow solver is tested for stability and convergence in the presence of interior flappers. An under-relaxation scheme has been incorporated to improve the solution stability. Important flow characteristics such as secondary flows, recirculation, vortex and wake regions, and separated flows are observed. Computed values for forces, moments, and pressure drop are in satisfactory agreement with water flow test data covering a maximum tube Reynolds number of 3.5 x 10(exp 6). The results will serve as a guide to improved design and enhanced testing of the disconnect.
Computer program generates sizes and shapes of cascade-type blades for use in axial or radial turbomachine diffusers. Generates shapes of blades rapidly, incorporating extensive cascade data to determine optimum incidence and deviation angle for blade design based on 65-series data base of National Advisory Commission for Aeronautics and Astronautics (NACA). Allows great variability in blade profile through input variables. Also provides for design of three-dimensional blades by allowing variable blade stacking. Enables designer to obtain computed blade-geometry data in various forms: as input for blade-loading analysis; as input for quasi-three-dimensional analysis of flow; or as points for transfer to computer-aided design.