SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Special micrometer measures diameter of circular groove on face of large part, while part is mounted in lathe chuck. Tool has curved frame so it can reach around obstruction on centerline of part. At one end of frame is blade/ micrometer spindle for reaching into groove to be measured; this type of spindle does not rotate when micrometer thimble is turned in taking measurement. Other end of frame has sliding foot with blade.
A multidimensional bipolar-adjective rating scale is employed as a subjective measure of operator workload in the performance of a one-axis tracking task. The rating scale addressed several dimensions of workload, including cognitive, physical, and perceptual task loading as well as fatigue and stress effects. Eight subjects performed a one-axis tracking task (with six levels of difficulty) and rated these tasks on several workload dimensions. Performance measures were tracking error RMS (root-mean square) and the standard deviation of control stick output. Significant relationships were observed between these performance measures and skill required, task complexity, attention level, task difficulty, task demands, and stress level.
The effects of time estimation technique and task condition on the production and verbal estimation of time intervals ranging from 5 to 14 sec were investigated. The duration of time intervals during each task condition pretracking, tracking (subject performed a one-axis tracking), and posttracking was estimated by the subjects. The ratio of the subject's time estimate to actual interval length was computed for each trial. Productions were typically longer than verbal estimates of the same duration and produced durations were typically too long whereas verbal estimates were too short relative to the correct duration. A significant interaction was found between counting technique and tracking condition for both estimation methods. A significant effect could be attributed to the addition of a tracking task: produced durations increased in length, whereas verbal estimates decreased in length. The durations produced without counting were significantly less accurate and consistent with the addition of a tracking task. Verbal estimation mean accuracy, but not consistency, was adversely affected by the addition of a tracking task when the subjects were instructed not to count.
A statistical ray analysis is used to analyze observed electron content and Faraday rotation fluctuations in the 2.29 GHz S band carrier signals of the two Helios spacecraft probing the magnetic and density structures of the solar corona inside 0.05 AU. It is found that (1) the observed Faraday rotation fluctuations cannot be due only to electron density fluctuations in the corona, unless the coronal magnetic field is about five times stronger than suggested by current estimates; and (2) the observed Faraday rotation fluctuations are consistent with the hypothesis that the sun radiates Alfven waves whose energies are great enough to heat and accelerate high-speed solar wind streams.
Tool with assembled components expedites bearing replacement in aircraft, ground vehicles, and other applications. New tool cuts lip on one side to facilitate bearing replacement. After bearing retaining lip is cut away, bearing pressed out. Tool makes it possible to replace bearings without disassembling structure.
Staking tool compact and portable. Tool combines clamping and staking operations in single unit. Tool clamps workpiece (a bearing or bushing), alines it, and stakes on of flat faces. Used for most roller staking operations which acess both faces of workpiece.
Centerlines of original bushings maintained. Tool frame extends around structure that holds bushings to be removed. Floating bushings of tool positioned with jig pin that slides snugly in old bushing and floating tool bushings. Floating bushings then clamped to tool frame.
Portable tool checks bushings and bearings in hard-to-reach places to ensure they are properly staked. Actuator plate with surfaces at 45 degrees to hydraulic cylinder shaft turns push or pull perpendicular to original direction. Tool makes unnecessary to disassemble equipment to gain access to parts.
This paper presents results of flowfield calculations for typical hypersonic reentry conditions encountered by the nose region of the Space Shuttle Orbiter. Most of the transitional flow regime is covered by the altitude range of 150 to 92 km. Calculations were made with the Direct Simulation Monte Carlo (DSMC) method that accounts for translational, rotational, vibrational, and chemical nonequilibrium effects. Comparison of the DSMC heating results with both Shuttle flight data and continuum predictions showed good agreement at the lowest altitude considered. However, as the altitude increased, the continuum predictions, which did not include slip effects, departed rapidly from the DSMC results by overpredicting both heating and drag. The results demonstrate the effects of rarefaction on the shock and the shock layer, along with the extent of the slip and temperature jump at the surface. Also, the sensitivity of the flow structure to the gas-surface interaction model, thermal accommodation, and surface catalysis are studied.
A new solution procedure has been developed to analyze the flowfield properties in the vicinity of the Inertial Upper Stage/Spacecraft during the 1st stage (SRMI) burn. Continuum methods are used to compute the nozzle flow and the exhaust plume flowfield as far as the boundary where the breakdown of translational equilibrium leaves these methods invalid. The Direct Simulation Monte Carlo (DSMC) method is applied everywhere beyond this breakdown boundary. The flowfield distributions of density, velocity, temperature, relative abundance, surface flux density, and pressure are discussed for each species for 2 sets of boundary conditions: vacuum and freestream. The interaction of the exhaust plume and the freestream with the spacecraft and the 2-stream direct interaction are discussed. The results show that the low density, high velocity, counter flowing free-stream substantially modifies the flowfield properties and the flux density incident on the spacecraft. A freestream bow shock is observed in the data, located forward of the high density region of the exhaust plume into which the freestream gas does not penetrate. The total flux density incident on the spacecraft, integrated over the SRM1 burn interval is estimated to be of the order of 10 to the 22nd per sq m (about 1000 atomic layers).
To determine the correct fault rheology of the Transverse Ranges area of California, a new finite element to represent faults and a mangle drag element are introduced into a set of 63 simulation models of anelastic crustal strain. It is shown that a slip rate weakening rheology for faults is not valid in California. Assuming that mantle drag effects on the crust's base are minimal, the optimal coefficient of friction in the seismogenic portion of the fault zones is 0.4-0.6 (less than Byerly's law assumed to apply elsewhere). Depending on how the southern California upper mantle seismic velocity anomaly is interpreted, model results are improved or degraded. It is found that the location of the mantle plate boundary is the most important secondary parameter, and that the best model is either a low-stress model (fault friction = 0.3) or a high-stress model (fault friction = 0.85), each of which has strong mantel drag. It is concluded that at least the fastest moving faults in southern California have a low friction coefficient (approximtely 0.3) because they contain low strength hydrated clay gouges throughout the low-temperature seismogenic zone.
Explore the source record for details and available documents.
The magnetized plasma of the solar corona was remotely sounded using the Faraday rotation effect. The solar magnetic field together with the electrons of the coronal plasma cause a measurable Faraday rotation effect, since the radio waves of Helios are linearly polarized. The measurement is performed at the ground stations. Alfven waves traveling from the Sun's surface through the corona into interplanetary space are observed. Helios 2 signals penetrating through a region where coronal mass is ejected show wavelike structures.
In testing a stochastic variational principle at high frequencies by using a Kirchhoffean trial function in an idealized model for surface scattering - a randomly embossed plane - we have found not only the predicted high-frequency improvement but also an unexpected low-frequency improvement in the calculated scattering amplitudes. To investigate systematically the all-frequency variational behavior, we consider here the deterministic one-boss case - Rayleigh's classic model whose exact solution is available for comparison - over all wavelengths, polarizations, and configurations of incidence and scattering. We examine analytically in particular the long-wave limit of the variational-Kirchhoff amplitudes; the results demonstrate improvements in both wavelength and angle depedence for horizontal (TM) polarization and some variational improvements for vertical (TE) polarization. This low-frequency behavior in tandem with the foreseen high-frequency improvement leads to good variational-Kirchhoff results through the intermediate resonance-frequency regime for this model.
The flow in the immediate vicinity of a rocket nozzle lip has been analyzed, and the results are presented. A rapid change in gas composition is observed in the flow around the lip depending principally on species molecular mass and local flow angle. The divergence of axial and radial temperatures indicating breakdown of translational equilibrium is observed in the results.
This paper presents the results of calculations obtained with a Direct Simulation Monte Carlo (DSMC) method that describes both the external flow about the nose region of the Shuttle Orbiter and the internal flow in an inlet tube that provides the initial path between the shock-processed gases and a mass spectrometer mounted inside the Orbiter. A dedicated, three-dimensional version of the DSMC was developed during this study for the internal flow simulation along with the procedure for interfacing the external and internal flows. The calculations span the 140 to 95 km altitude range, which includes most of the hypersonic transitional flow encountered during reentry. All calculations were for a multicomponent gas mixture consisting of five chemical species while simulating the effects of transitional, rotational, vibrational, and chemical nonequilibrium. The results of the calculations show that within the entry region of the inlet tube where the gas has equilibrated with the sidewall tube temperature, the pressure is substantially less than the pressure at the external surface. This pressure correction for the entry region is significant for all conditions investigated and increases with altitude. The results highlight the structure of both the external and internal flow. Results of parametric studies show the sensitivity of the equilibrated inlet sidewall pressure to mass flow rates, gas-surface reflection model, tube side-wall temperature variations, and surface recombinations.
Doppler temperatures determined from observations of the atomic oxygen OI 6300 A line during March 1984 at the University of Alaska/Fairbanks are presented. Temperatures are obtained from Fabry-Perot Interferometer pressure scans using a Fourier transform smoothing and fitting technique; this technique is presented in detail. The temperatures and the spread in the temperatures are consistent from day to day. On the clear nights of March 10 to 13, the temperatures were 800, 750, 750 and 800 K, respectively, with a spread of + or - 100 K. These temperatures are compared to the MSIS (84) model atmosphere for similar geomagnetic conditions and found to be in general agreement; they are also consistent with results obtained by other investigators.
A hydraulically actuated device is described for applying a test load to a bearing or the like to prove the integrity of its mounting or staking within a bore in a housing such as gear case. To accommodate limited access situations, the device is constructed in a right angle configuration in which a hydraulic cylinder applies axial pressure to a first thrust rod assemly which includes a first thrust rod through a threated spindle driving a linearly translated cam. Cam follower wheel transfers the translation to a second thrust rod assembly which includes a horizontal shaft and a spindle within a cross-arm housing portion and a tubular housing portion. The same second thrust direction applies the bearing loading in either of two directions depending upon the shape of the interface parts. The interface parts can bear on the bearing from either side with respect to the bearing mounting structural part.