Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Dual Tunability for Uncatalyzed N‐Alkylation of Primary Amines Enabled by Plasma‐Microdroplet Fusion

Abstract The fusion of non‐thermal plasma with charged microdroplets facilitates catalyst‐free N‐alkylation for a variety of primary amines, without halide salt biproduct generation. Significant reaction enhancement (up to >200×) is observed over microdroplet reactions generated from electrospray. This enhancement for the plasma‐microdroplet system is attributed to the combined effects of energetic collisions and the presence of reactive oxygen species (ROS). The ROS (e.g., O 2 ⋅ − ) act as a proton sink to increase abundance of free neutral amines in the charged microdroplet environment. The effect of ROS on N‐alkylation is confirmed through three unique experiments: (i) utilization of radical scavenging reagent, (ii) characterization of internal energy distribution, and (iii) controls performed without plasma, which lacked reaction acceleration. Establishing plasma discharge in the wake of charged microdroplets as a green synthetic methodology overcomes two major challenges within conventional gas‐phase plasma chemistry, including the lack of selectivity and product scale‐up. Both limitations are overcome here, where dual tunability is achieved by controlling reagent concentration and residence time in the microdroplet environment, affording single or double N‐alkylated products. Products are readily collected yielding milligram quantities in eight hours. These results showcase a novel synthetic strategy that represents a straightforward and sustainable C−N bond‐forming process.

Chemistry↗
DOE OSTI2024

On‐Surface Synthesis and Determination of the Open‐Shell Singlet Ground State of Tridecacene**

Abstract The character of the electronic structure of acenes has been the subject of longstanding discussion. However, convincing experimental evidence of their open‐shell character has so far been missing. Here, we present the on‐surface synthesis of tridecacene molecules by thermal annealing of octahydrotridecacene on a Au(111) surface. We characterized the electronic structure of the tridecacene by scanning probe microscopy, which reveals the presence of an inelastic signal at 126 meV. We attribute the inelastic signal to spin excitation from the singlet diradical ground state to the triplet excited state. To rationalize the experimental findings, we carried out many‐body ab initio calculations as well as model Hamiltonians to take into account the effect of the metallic substrate. Moreover, we provide a detailed analysis of how the dynamic electron correlation and virtual charge fluctuation between the molecule and metallic surface reduces the singlet‐triplet band gap. Thus, this work provides the first experimental confirmation of the magnetic character of tridecacene.

Chemistry↗
DOE OSTI2024

Ultrafast Formation of Charge Transfer Trions at Molecular‐Functionalized 2D MoS 2 Interfaces

In this work, we investigate trion dynamics occurring at the heterojunction between organometallic molecules and a monolayer transition metal dichalcogenide (TMD) with transient electronic sum frequency generation (tr-ESFG) spectroscopy. By pumping at 2.4 eV with laser pulses, we have observed an ultrafast hole transfer, succeeded by the emergence of charge-transfer trions. This observation is facilitated by the cancellation of ground state bleach and stimulated emission signals due to their opposite phases, making tr-ESFG especially sensitive to the trion formation dynamics. The presence of charge-transfer trion at molecular functionalized TMD monolayers suggests the potential for engineering the local electronic structures and dynamics of specific locations on TMDs and offers a potential for transferring unique electronic attributes of TMD to the molecular layers.

Time-resolved↗
DOE OSTI2024

Does H 2 Temperature–Programmed Reduction Always Probe Solid–State Redox Chemistry? The Case of Pt/CeO 2

Redox reactions on the surface of transition metal oxides are of broad interest in thermo, photo, and electrocatalysis. H 2 temperature-programmed reduction (H 2 -TPR) is commonly used to probe oxide reducibility by measuring the rate of H 2 consumption during temperature ramps, assuming that this rate is controlled by oxide reduction. However, oxide reduction involves several elementary steps, such as H 2 dissociation and H-spillover, before surface reduction and H 2 O formation occur. In this study, we evaluated the kinetics of H 2 consumption over CeO 2 and Pt/CeO 2 with varying Pt loadings and structures to identify the elementary steps probed by H 2 -TPR. Literature often attributes changes in H 2 -TPR characteristics with Pt addition to increased CeO 2 reducibility. However, our analysis revealed that the H 2 consumption rate is measurement of the rate of H-spillover at Pt-CeO 2 interfaces and is determined by the concentration of Pt species on Pt nanoclusters that dissociate H 2 . Furthermore, lower temperature H 2 consumption observed with Pt addition does not indicate higher CeO 2 reducibility. Measurements on samples with mixtures of Pt single-atoms and nanoclusters demonstrated that H 2 -TPR can effectively quantify dilute Pt nanocluster concentrations, suggesting caution in directly linking H 2 -TPR characteristics to oxide reducibility while highlighting alternative material insights that can be gleaned.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Trade‐Off Between Toxicity and Efficiency in Tin‐ versus Lead‐Based Halide Perovskites

Toxicity remains one of the major challenges that prevent Pb-based halide perovskites from widespread utilization. Ideally, non-toxic alternatives can be identified while still maintaining the superior power conversion efficiency of the Pb-based perovskite solar cells. Using the currently most promising candidate, the Sn-based halide perovskites, as an example, we show that a trade-off exists between toxicity and efficiency in the Sn- versus Pb-based halide perovskites. Indeed, the dominant nonradiative recombination center in the Sn-based halide perovskites differs from the one in its Pb-based counterparts, resulting in the nonradiative capture coefficient in CsSnI 3 being an order of magnitude higher than that in CsPbI 3 . We attribute this difference to the band alignment. Here, our results indicate that development of halide perovskites beyond the Pb and Sn bases is essential for efficient yet environmentally friendly perovskite solar cells.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Spin‐State and Clustering Effects in Fe‐Complex Negolytes for Near‐Neutral Aqueous Redox Flow Batteries

Cost-effective redox-active materials are essential for advancing redox flow batteries (RFBs). Iron, with its abundance and suitability as a redox couple, is a promising candidate; however, achieving stable and fast redox reactions in aqueous RFBs remains a challenge. Here, this study presents an Fe-based negolyte stabilized by a hexadentate ligand, where Fe–ligand bonds are enhanced through intermolecular interactions. The sulfonate-substituted Fe complex exhibits a formal potential of −0.44 V versus Ag/AgCl and an exceptionally high rate constant of 0.69 cm s −1 . Near-neutral RFBs incorporating 0.5 M Fe complex show excellent cycling stability, with no discernible capacity fading over 300 cycles. This performance is attributed to intermolecular hydrogen bonds that reinforce Fe–ligand coordination and promote the formation of stable trimeric clusters. Operando electrochemical Raman spectroscopy and density functional theory reveal that π-backdonation from Fe(II) to the imino-phenolate moiety further stabilizes the complex after reduction. In contrast, the hydroxyl-substituted complex exhibits inferior stability due to weaker hydrogen bonding and less pronounced π-backdonation. These findings underscore the importance of ligand design and intermolecular interactions in developing cost-effective, high-performance redox-active materials for aqueous RFBs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Can Charge Transfer Across C─H⋅⋅⋅O Hydrogen Bonds Stabilize Oil Droplets in Water?

Oil-water emulsions resist aggregation due to the presence of negative charges at their surface that leads to mutual repulsion between droplets, but the molecular origin of oil charge is currently under debate. Although much evidence has suggested that ionic species must accumulate at the interface, an alternative perspective attributes the negative charge on the oil droplet to charge transfer of electron density from water to oil molecules. Although the charge transfer mechanism is consistent with the correct sign of oil charge, it is just as important to provide good estimates of the charge magnitude to explain emulsion stability and electrophoresis experiments. Here, we show using energy decomposition analysis that the amount of net flow of charge from water to oil is negligibly small due to nearly equal forward and backward charge transfer through weak oil-water interactions, such that oil droplets would be unstable and coalesce, contrary to experiment. The lack of charge transfer also explains why vibrational sum frequency scattering reports a blue shift in the oil C-H frequency when forming emulsions with water, which arises from Pauli repulsion due to localized confinement at the interface. Finally, unlike ions, neither charge transfer nor dynamic polarization can produce a finite conductivity needed to couple to electric fields that would explain electrophoretic mobility.

Zhao, Ruoqi↗
DOE OSTI2025

Revealing Parallel Inter‐ and Intra‐Ligand Charge Transfer Dynamics in [Ru(L) 2 (dppz)] 2+ Molecular Lightswitch with N K‐Edge X‐Ray Absorption Spectroscopy

In photoactive metal complexes the localization of photoexcited charges dictates the site of chemical reactivity, but few studies measure the charge redistribution in these systems with spatial precision. Herein, we track the inter- and intra-ligand charge transfer processes that underpin light-driven charge separation in the well-studied “molecular lightswitch” [Ru(bpy) 2 dppz] 2+ (aqueous [Ruthenium II (2,2′-bipyridine)2(dipyrido[3,2-a:2′,3′-c]phenazine)] 2+ [Cl − ] 2 ) by probing the electronic structure of ligand nitrogen atoms in real-time using ultrafast X-ray absorption spectroscopy and first principles calculations. We confirm the localization of excited electron density on the phenazine N atoms of dppz and we newly identify two parallel electron transfer pathways to populate this state. Sub-70 fs electron transfer to the phenazine portion of dppz is observed and attributed to intra-ligand electron transfer following Ru-to-dppz metal-to-ligand charge transfer (MLCT) excitation. This fast charge transfer was not reported in prior ultrafast studies. The slower (ca. 2 ps) charge transfer reported extensively in time-resolved optical absorption and emission studies is reassigned here to inter-ligand electron “hopping” between nearly isoenergetic ligand moieties following Ru-to-bpy MLCT excitation. In conclusion, the results demonstrate much faster charge separation than previously identified in this well-studied system, highlighting how extended azaacene ligand motifs promote the competitive charge transfer processes needed to drive light-driven electron transfer chemistry.

Donor-acceptor systems↗
DOE OSTI2022

Prediction of curing kinetics of resorcinol‐added resole phenolic resins using differential scanning calorimetry for the fabrication of carbon/carbon composites

Phenolic resins are commonly used as carbon precursors for the fabrication of carbon/carbon composites due to their high carbon yield and aromatic nature. To decrease curing times, acid catalysts are generally used, but the addition of resorcinol was found to have a similar effect while being incorporated into the resin matrix with no contamination or corrosion issues. In this work, the curing kinetics of pure, 10, 20, and 30 wt% resorcinol-added phenolic resins were investigated through differential scanning calorimetry. Heating rates of 0.5, 1, 2.5, and 5°C min -1 were used with several curing models to predict isothermal curing. Averaged mean absolute error (MAE) for the isoconversional mathematical approaches namely Kissinger–Akahira–Sunose (MAE = 12.9 min), Flynn–Wall–Ozawa (15.8 min), and Vyazovkin (14 min) show that these methods provide the best predictions, attributed to their adoption of an activation energy that depends on the extent of cure (E a (α)). The Kissinger method (MAE = 36 min), which depends only on peak temperature with a constant activation energy assumption, and the data noise sensitive Friedman model (MAE = 1144.7 min) provide the least accurate results. Thermogravimetric analysis revealed that resorcinol decreases the curing times by up to 71% without lowering carbon yield.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Atomic force microscopy and scanning electron microscopy characterization of the controlling of surface morphology of epoxy‐amine‐cured spin‐coated films

Abstract Atomic force microscopy (AFM) was successfully used to study spin‐coated, amine‐cured epoxy film microstructure and morphology. The air‐epoxy and epoxy‐substrate interfaces were examined using tapping‐mode height and phase imaging AFM. The impact of relative humidity on the morphology and microstructure of the surfaces was determined. AFM was able to elucidate the changes on the surface as relative humidity during processing increased. It was observed that large nodular formations formed on the epoxy surface expose to the air but not epoxy surface formed on the substrate in addition to varying regions of more or less compliant structures, which was attributed to carbamate formation caused by the amine curing agent reaction with atmospheric CO 2 . Scanning electron microscopy (SEM) was used to further elucidate interface and interphase morphology of spin‐coated epoxies. Experimentation also demonstrated that post‐curing above the glass transition did not change the morphology structure, suggesting surface structures are “locked‐in.” SEM was used to further elucidate how the interface and interphase change with changing environmental conditions at both the air‐epoxy and epoxy‐substrate interface/interphases, including the impact of atmospheric CO 2 on Marangoni cell formation.

Shenk, Timothy M.↗
DOE OSTI2026

Toluene Uptake and Outgassing by a 3D-Printed Silicone and the Impact on Mechanical Performance

Silicone elastomers have advantageous physical properties and are widely used in various applications. Additive manufacturing (AM) of silicones provides additional utility by enabling tunable mechanical and functional properties. However, the performance of these elastomers deteriorates over time with exposure to environmental stressors. Organic solvents and volatile organic compounds (VOCs) are stressors that can cause dimensional changes to silicones with exposure and impact the overall function. Yet, the effects of such exposure on mechanical performance, including load response (LR), are not well understood. Here, in this study, we investigated the impact of a nonpolar solvent, toluene, on AM silicone material properties and compressive load. We observed that AM silicones rapidly absorbed toluene and swelled, leading to an increase in relative LR. Toluene concentration and compression did not affect uptake or swelling rates. In contrast, outgassing rates were slower for compressed coupons compared to uncompressed specimens, attributed to geometric constraints and polymer network changes impacting toluene diffusion outward. Compression also pinned the AM silicones at an enlarged state, significantly reducing relative LR after outgassing. Depending on toluene concentrations and compression, AM silicones can remain robust against toluene exposure and recover their initial printing geometry and mechanical performance after toluene outgassing and polymer relaxation.

Materials science↗
DOE OSTI2020

Super resolution for root imaging

Premise High‐resolution cameras are very helpful for plant phenotyping as their images enable tasks such as target vs. background discrimination and the measurement and analysis of fine above‐ground plant attributes. However, the acquisition of high‐resolution images of plant roots is more challenging than above‐ground data collection. An effective super‐resolution (SR) algorithm is therefore needed for overcoming the resolution limitations of sensors, reducing storage space requirements, and boosting the performance of subsequent analyses. Methods We propose an SR framework for enhancing images of plant roots using convolutional neural networks. We compare three alternatives for training the SR model: (i) training with non‐plant‐root images, (ii) training with plant‐root images, and (iii) pretraining the model with non‐plant‐root images and fine‐tuning with plant‐root images. The architectures of the SR models were based on two state‐of‐the‐art deep learning approaches: a fast SR convolutional neural network and an SR generative adversarial network. Results In our experiments, we observed that the SR models improved the quality of low‐resolution images of plant roots in an unseen data set in terms of the signal‐to‐noise ratio. We used a collection of publicly available data sets to demonstrate that the SR models outperform the basic bicubic interpolation, even when trained with non‐root data sets. Discussion The incorporation of a deep learning–based SR model in the imaging process enhances the quality of low‐resolution images of plant roots. We demonstrate that SR preprocessing boosts the performance of a machine learning system trained to separate plant roots from their background. Our segmentation experiments also show that high performance on this task can be achieved independently of the signal‐to‐noise ratio. We therefore conclude that the quality of the image enhancement depends on the desired application.

Ruiz‐Munoz, Jose F.↗
DOE OSTI2022

Adoption of biofuels for marine shipping decarbonization: A long‐term price and scalability assessment

Abstract This study assessed the long‐term annual biofuel production capacity potential and price in the United States and shed light on the prospect of biofuel adoption for marine propulsion. A linear programming model was developed to assist the projections and provide insightful analyses. The projected long‐term (2040) maximum annual capacity of biofuels in the United States is 245 million metric tons (Mt) or 65 billion gallons of heavy fuel oil gallon equivalent (HFOGE) when based on the median feedstock availability. Between 2022 (near‐term) and 2040, the potential biofuel capacity increases by over 40%, attributed to increased feedstock availability. At a price range up to $500/t, biodiesel is the main product, and the annual capacity (12 Mt) is limited to feedstock availability constraints. Biodiesel and corn ethanol are the main biofuels at a price range up to $750/t. At a higher price point (above $750/t), the biofuel types and annual capacities increase substantially (218 Mt per year). Biofuels above this price include gasoline‐, jet‐, and diesel‐range blendstocks, as well as bio‐methanol, bio‐propane, and biogas. This study concludes that the US domestic feedstock availability coupled with advanced conversion technologies can produce substantial amounts of biofuels to achieve a critical mass and be impactful as alternative marine fuels. There is also a need to improve the biofuel price for marine shipping adoption. Policies and economic incentives that provide temporary financial support would help facilitate maritime biofuel adoption. © 2022 Alliance for Sustainable Energy, LLC. Biofuels, Bioproducts and Biorefining published by Society of Industrial Chemistry and John Wiley & Sons Ltd.

09 BIOMASS FUELS↗
DOE OSTI2023

Electrogenetic signaling and information propagation for controlling microbial consortia via programmed lysis

To probe signal propagation and genetic actuation in microbial consortia, we have coopted the components of both redox and quorum sensing (QS) signaling into a communication network for guiding composition by “programming” cell lysis. Here, in this paper, we use an electrode to generate hydrogen peroxide as a redox cue that determines consortia composition. The oxidative stress regulon of Escherichia coli, OxyR, is employed to receive and transform this signal into a QS signal that coordinates the lysis of a subpopulation of cells. We examine a suite of information transfer modalities including “monoculture” and “transmitter-receiver” models, as well as a series of genetic circuits that introduce time-delays for altering information relay, thereby expanding design space. A simple mathematical model aids in developing communication schemes that accommodate the transient nature of redox signals and the “collective” attributes of QS signals. We suggest this platform methodology will be useful in understanding and controlling synthetic microbial consortia for a variety of applications, including biomanufacturing and biocontainment.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Defining Golden Batches in Biomanufacturing Processes From Internal Metabolic Activity to Detect Process Changes That May Affect Product Quality

ABSTRACT Cellular metabolism plays a role in the observed variability of a drug substance's Critical Quality Attributes (CQAs) made by biomanufacturing processes. Therefore, here we describe a new approach for monitoring biomanufacturing processes that measures a set of metabolic reaction rates (named Critical Metabolic Parameters (CMP) in addition to the macroscopic process conditions currently being used as Critical Process Parameters (CPP) for biomanufacturing. Constraint‐based systems biology models like Flux Balance Analysis (FBA) are used to estimate metabolic reaction rates, and metabolic rates are used as inputs for multivariate Batch Evolution Models (BEM). Metabolic activity was reproducible among batches and could be monitored to detect a deliberately induced macroscopic process shift (i.e., temperature change). The CMP approach has the potential to enable “golden batches” in biomanufacturing processes to be defined from the internal metabolic activity and to aid in detecting process changes that may impact the quality of the product. Overall, the data suggested that monitoring of metabolic activity has promise for biomanufacturing process control.

Biotechnology & Applied Microbiology↗
DOE OSTI2025

Temporal Galactose‐Manganese Feeding in Fed‐Batch and Perfusion Bioreactors Modulates UDP‐Galactose Pools for Enhanced mAb Glycosylation Homogeneity

ABSTRACT Monoclonal antibodies (mAbs) represent a majority of biotherapeutics in the market today. These glycoproteins undergo posttranslational modifications, such as N‐linked glycosylation, that influence the structural & functional characteristics of the antibody. Glycosylation is a heterogenous posttranslational modification that may influence therapeutic glycoprotein stability and clinical efficacy, which is why it is often considered a critical quality attribute (CQA) of the mAb product. While much is known about the glycosylation pathways of Chinese Hamster Ovary (CHO) cells and how cell culture chemical modifiers may influence the N‐glycosylation profile of the final product, this knowledge is often based on the final cumulative glycan profile at the end of the batch process. Building a temporal understanding of N‐glycosylation and how mAb glycoform composition responds to real‐time changes in the biomanufacturing process will help build integrated process models that may allow for glycosylation control to produce a more homogenous product. Here, we look at the effect of specific nutrient feed media additives (e.g., galactose, manganese) and feeding times on the N‐glycosylation pathway to modulate N‐glycosylation of a Herceptin biosimilar mAb (i.e., Trastuzumab). We deploy the N‐GLYcanyzer process analytical technology (PAT) to monitor glycoforms in near real‐time for bench‐scale bioprocesses operated in both fed‐batch and perfusion modes to build an understanding of how temporal changes in mAb N‐glycosylation are dependent on specific media additives. We find that Trastuzumab terminal galactosylation is sensitive to media feeding times and intracellular nucleotide sugar pools. Temporal analysis reveals an increased desirable production of single and double galactose‐occupied glycoforms over time under glucose‐starved fed‐batch cultures. Comparable galactosylation profiles were also observed between fed‐batch (nutrient‐limited) and perfusion (non‐nutrient‐limited) bioprocess conditions. In summary, our results demonstrate the utility of real‐time monitoring of mAb glycoforms and feeding critical cell culture nutrients under fed‐batch and perfusion bioprocessing conditions to produce higher‐quality biologics.

Biotechnology & Applied Microbiology↗