Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “alloying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Design and Characterization of Hierarchically-Strengthened, Cast Al-Ce-Ni-Mn-Sc-Zr Alloys for High-Temperature Applications

We characterize the microstructure and mechanical properties of cast Al-Ce-Ni-Mn-Sc-Zr alloys designed for structural use above 300 °C. We first report on the effect of Ni on the as-cast phase formation, where all alloys consist of fine Al11Ce3 and Ni-rich eutectic phases, but the identity of the Ni-rich phase varies with Ni content. Furthermore, these alloys contain four coarsening-resistant strengthening phases as determined from SEM and APT investigations: (i) Al11Ce3 and (ii) Ni-rich micron-scale platelets formed during eutectic solidification, (iii) L12-Al3(Sc,Zr) nanoprecipitates formed during secondary aging, and (iv) Mn solute in the α-Al matrix. The Al-Ce-Ni-Mn-Sc-Zr alloy possesses higher microhardness and creep resistance than compositionally simpler alloys containing fewer of the strengthening phases, indicating that these strengthening mechanisms synergize to provide increased ambient- and elevated-temperature strength.

Ekaputra, Clement↗
DOE OSTI2026

Investigation of the Surface Chemistry of Magnesium and Magnesium Alloy Powders

Magnesium (Mg) and Mg alloy powders are generally difficult to sinter at atmospheric pressure in inert atmospheres purportedly due to the presence of powder particle surface oxide layers. To better understand sintering of Mg and Mg alloy powders, x-ray photoelectron spectroscopy (XPS) was performed to characterize the surface chemistry of gas atomized pure Mg and Mg alloys AZ91D and WE43 powders. These results are used to quantitatively determine the surface chemistry of these powders. Additionally, equilibrium thermodynamic modeling of these Mg/Mg alloys materials exposed to oxygen down to part per billion concentrations are presented for relative comparison to experimental XPS results. Analysis of these results are intended to improve sintering of Mg and Mg alloy powder materials through more quantitative knowledge of powder surface chemistry.

25 ENERGY STORAGE↗
DOE OSTI2020

Hydrogen Adsorption on Ordered and Disordered Pt-Ni Alloys

The bulk properties and chemical reactivity of disordered Pt-Ni alloys in the A1 ( fcc ) structure are investigated herein using different methods: Virtual Crystal Approximation (VCA), Korringa–Kohn–Rostoker Coherent Potential Approximation (KKR-CPA), and large explicit supercells generated using Super-Cell Random Approximates (SCRAPs). While VCA predicts lattice constants that closely follow Vegard’s law, the large supercells and KKR-CPA predict lattice constants that are consistently larger than Vegard’s law. KKR-CPA results closely agree with those from the large supercells for the disordered alloys, producing similar projected density of states and magnetic moment across the composition range. For instance, while VCA predicts the disordered alloys to be non-magnetic at a Pt concentration ( x Pt ) ≥ 0.5, KKR-CPA and SCRAPs predict the disordered alloys to remain ferromagnetic to higher Pt concentrations. As x Pt decreases, the adsorption of H becomes more exothermic on bulk-terminated (111) surfaces but less exothermic on Pt monolayer-terminated (111) surfaces due largely to strain effects. (111) surfaces cut from the large supercells predict average H adsorption energies on the disordered alloys similar to those on the ordered phases of the same compositions, while VCA predicts H adsorption to be more exothermic.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Design, Processing, and Properties of WTaCrV-Hf Multi-principal Element Alloys

Refractory multi-principal element alloys are candidates for high-temperature structural components due, in part, to their high strength and high melting points. Single-phase materials are initially preferred for isotropic material properties as a function of time and temperature in service conditions. This work outlines a computational rank-ordering and experimental validation methodology for single-phase body-centered-cubic phase stability in WTaCrV-Hf alloys using order–disorder transition temperature. Eight compositions were fabricated by arc-melting and heat-treated at 1400 °C for 24 hrs. X-ray diffraction, energy-dispersive x-ray spectroscopy, and Vickers hardness testing showed alloys with order–disorder transition temperatures below 600 °C formed a single-phase body-centered-cubic structure during solidification and remained single-phase after heat-treatment. The sample possessing the lowest order–disorder transition temperature exhibited slip traces suggestive of room-temperature plastic deformation under Vickers indentation, with both heat-treated single-phase samples exhibiting hardnesses over 800 HV with little cracking compared to tungsten. These results establish order–disorder transition temperature as a viable predictive parameter for multi-principal element alloy phase stability. The methodology outlined in this work provides a framework for future design, fabrication, and characterization of high-temperature structural multi-principal element alloys.

CALPHAD↗
DOE OSTI2020

Stacking Fault Energy Based Alloy Screening for Hydrogen Compatibility

The selection of austenitic stainless steels for hydrogen service is challenging since there are few intrinsic metrics that relate alloy composition to hydrogen degradation. One such metric, explored here, is intrinsic stacking fault energy. Stacking fault energy has an influence on the character and structure of dislocations and on the formation of secondary crystalline phases created during mechanical deformation in austenitic alloys. In this work, a data-driven model for the intrinsic stacking fault energy of common austenitic stainless steel alloys is applied to compare the relative degradation of tensile performance in the presence of hydrogen. A transition in the tensile reduction of area of both 300-series and manganese stabilized stainless steels is observed at a calculated stacking fault energy of approximately 43 mJ m -2 , below which pronounced hydrogen degradation on tensile ductility is observed. The model is also applied to suggest alloying strategies for low nickel austenitic stainless steels for hydrogen service. Lastly, through this investigation, we find that calculated intrinsic stacking fault energy is a high-throughput screening metric that enables the ranking of the performance of a diverse range of austenitic stainless steel compositions, as well as the identification of new alloys, with regard to hydrogen compatibility.

08 HYDROGEN↗
DOE OSTI2020

Uncertainty Quantification of Machine Learning Predicted Creep Property of Alumina-Forming Austenitic Alloys

The development of machine learning (ML) approaches in materials science offers the opportunity to exploit existing engineering and developmental alloy datasets, such as Oak Ridge National Laboratory (ORNL)’s consistently measured creep-rupture dataset for alumina-forming austenitic (AFA) alloys, to accelerate their further development. As a first step toward achieving ML insights for improved alloy design, the potential sources of uncertainty and their impacts on ML output are examined. It is observed that the selection of algorithms and features as well as data sampling significantly affects the performance of ML models, either positively or negatively. Further, the performance of various ML models in predicting the creep properties of AFA alloys is compared, with further evaluation by assessment of a small set of new developmental AFA alloys that were not part of the training dataset. The present study demonstrates that uncertainty quantification (UQ) is essential in materials science for evaluating the performance of ML algorithms with specifically selected feature sets and obtaining a comprehensive understanding of their limitations and the resultant capability of effective prediction in complex materials systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The Role of Oxidation Resistance in High Temperature Alloy Selection for a Future with Green Hydrogen

Hydrogen is being considered integral to the future energy landscape but there is limited mechanistic understanding and a lack of predictive models to describe the combined effects of alloy and gas composition, temperature, thermal cycling and water vapor contents on the oxidation behavior of high-temperature materials. Experimental evaluations were combined with coupled thermodynamic-kinetic modeling to investigate the oxidation behavior of five representative Ni-based superalloys in two water vapor contents (10%, 60% H 2 O) under thermal cycling (1-h, 100-h cyles) conditions at 800°C and 1000°C. The alloy with the highest Ti content demonstrated the poorest cyclic oxidation behavior while the alloy with highest Cr and Al contents was expected to continue to support protective formation of a compact Al 2 O 3 scale. Finally, accelerated degradation of the chromia-forming alloys was observed in the higher water vapor content but the impact on transient oxidation of the alumina-forming alloys needs further investigations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Emerging Opportunities in Manufacturing Bulk Soft-Magnetic Alloys for Energy Applications: A Review

Abstract Soft-magnetic alloys exhibit exceptional functional properties that are beneficial for a variety of electromagnetic applications. These alloys are conventionally manufactured into sheet or bar forms using well-established ingot metallurgy practices that involve hot- and cold-working steps. However, recent developments in process metallurgy have unlocked opportunities to directly produce bulk soft-magnetic alloys with improved, and often tailorable, structure–property relationships that are unachievable conventionally. The emergence of unconventional manufacturing routes for soft-magnetic alloys is largely motivated by the need to improve the energy efficiency of electromagnetic devices. In this review, literature that details emerging manufacturing approaches for soft-magnetic alloys is overviewed. This review covers (1) severe plastic deformation, (2) recent advances in melt spinning, (3) powder-based methods, and (4) additive manufacturing. These methods are discussed in comparison with conventional rolling and bar processing. Perspectives and recommended future research directions are also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

How Cerium and Lanthanum as Coproducts Promote Stable Rare Earth Production and New Alloys

The largest outputs of rare earth mining are the low-value byproducts cerium and lanthanum, which burden rare earth supply chains because they must be separated from more desirable rare earths used in magnet production. Promoting demand for cerium and lanthanum can potentially diversify the economics of rare earth mining and improve supply chain stability for all rare earth elements. A promising avenue for increasing byproduct rare earth element demand is their use in aluminum alloys; an application for cerium and lanthanum offering multiple benefits to manufacturing such as energy reduction and improved throughput. Experimental materials science and economic implications of Al-rare earth element alloys will be discussed. We show that Al–La/Ce alloys have elevated mechanical strength compared to more traditional aluminum alloys, in some formulations can be used without heat treatment, and possess a highly castable eutectic microstructure. This report presents the use of cerium and lanthanum in aluminum alloys as an example of how supply chain focused approaches to technological development can benefit stakeholders at every step in production.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dynamic Tensile Response of a Fe–49Co–2V Alloy at Various Strain Rates and Temperatures

Soft ferromagnetic alloys are often utilized in electromagnetic applications due to their desirable magnetic properties. In support of these applications, the ferromagnetic alloys are also required to bear mechanical load under various loading and environmental conditions. In this study, a Fe–49Co–2V alloy was dynamically characterized in tension with a Kolsky tension bar and a Drop–Hopkinson bar at various strain rates and temperatures. Dynamic tensile stress–strain curves of the Fe–49Co–2V alloy were obtained at strain rates ranging from 40 to 230 s -1 and temperatures from - 100 to 100 °C. All dynamic tensile stress–strain curves exhibited an initial linear elastic response to an upper yield followed by Lüders band response and then a nearly linear work-hardening behavior. The yield strength of this material was found to be sensitive to both strain rate and temperature, whereas the hardening rate was independent of strain rate or temperature. The Fe–49Co–2V alloy exhibited a feature of brittle fracture in tension under dynamic loading with no necking being observed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Nanotwinned alloys under high pressure

Nanotwinned alloys are of interest due to their high strength and ductility, but twin boundaries may not be stable under shear. Computational studies indicate that high hydrostatic pressure may suppress detwinning mechanisms. Here, in this study, we investigate the microstructural changes of nanotwinned-nanocrystalline copper-nickel and Inconel 725 alloys under quasi-hydrostatic pressures up to 50 gigapascals (GPa). The alloys are compressed in a diamond anvil cell. In-situ x-ray diffraction (XRD) and ex-situ transmission electron microscopy (TEM) were employed to monitor microstructural changes. Twin boundary deformation and grain growth occur at 11.4 GPa quasi-hydrostatic pressure in the copper-nickel alloy. Molecular dynamics (MD) simulations reveal that hydrostatic pressure causes elevated local shear stress at grain boundaries, which leads to atomic rearrangements. A superposition of hydrostatic and deviatoric pressures lead to partial dislocation mediated twin boundary migration. In contrast, the Inconel 725 alloy showed stable twin and grain boundaries up to a quasi-hydrostatic pressure of 12.7 GPa. Texture, high solid solution strengthening, and low stacking fault energy are hypothesized to the enhanced microstructural stability in Inconel 725.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A theoretical calculation of stacking fault energy of Ni alloys: The effects of temperature and composition

Combining cluster expansion (CE) method with one dimensional axial Ising model, this work investigated the effects of alloying elements and configurational variations due to temperature on the stacking fault energy (SFE) of FCC Ni binary alloys. Ensembles of large numbers of atomistic structures, each with more than ~400 atoms, were generated to consider sufficient long-range chemical disorder and temperature effects due to configurational entropy. Here, a Monte Carlo Metropolis algorithm was used to generate these structures, whose energies were then evaluated based on the effective cluster interactions obtained from CE. As a baseline, this work had shown the SFE of pure Ni and Al to be 127 mJ/m 2 and 137 mJ/m 2 , respectively, which agreed with the experimental values of 125 mJ/m 2 and 150 mJ/m 2 reported in the literature. Additions of Al, Ti, Cr and Co to pure Ni were found to decrease the SFE to different extents. Although temperature does not strongly influence the SFE of the FCC Ni-Al and Ni-Cr binary alloys, it can lead to significant changes to the SFE of the FCC Ni-Ti and Ni-Co alloys. While effects of temperature and composition on SFE observed in this work were calculated from binary Ni alloys, the general trends are nonetheless expected to be valid in the γ phase of multicomponent Ni superalloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding solidification of near eutectic alloy using Cellular Automata (CA)

The solidification microstructure of an alloy strongly influences the mechanical properties. Dendritic and eutectic solidification are two important pathways of alloy solidification. The formation of phases, and their size and distribution depend on which pathway to take. In contrast to the Scheil model that has been widely used in describing the solidification pathways of alloys manufactured from conventional casting approach, more sophisticated solidification models are required to describe the state-of-the art manufacturing processes, such as additive manufacturing where distinctly different phase morphology, size and distribution than conventional casting can form, due to the vast difference in cooling conditions. Therefore, this work is to develop a computational Cellular Automata framework which includes the modeling of nucleation and growth of dendritic and eutectic solidification, as well as their competition as a function of alloy composition, undercooling and cooling rate. Further, after individual solidification models were validated against analytical solutions, the models were then combined to predict the competition between dendritic and eutectic solidification in alloys with off-eutectic compositions. This work predicts increased cooling rates suppress the dendritic solidification and promote eutectic solidification. Although quantitative validation is needed, this finding is consistent with qualitative observation in literature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Carburization susceptibility of chromia-forming alloys in high-temperature CO 2

It is generally believed that when a chromia scale forms in high-temperature CO 2 environments, carbon uptake of alloys is nearly eliminated, thereby preventing carburization and associated degradation of properties. We quantitively assess this notion through careful examination of several chromia-forming Ni-based and Fe-based commercial alloys after long-term (10,000-h) exposures to CO 2 and air at 700°C. Here, small but measurable carbon uptake ensued independent of alloy base metal (Ni/Fe), alloy crystal structure (FCC/BCC), and chromia growth rate. The rate for Ni-based alloys was strongly dependent on Si and Mn content, highlighting the need to understand possible long-term effects on mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of aluminum on the FeCr(Al) alloy oxidation resistance in steam environment at low temperature (400 °C) and high temperature (1200 °C)

The effect of aluminum in the FeCr(Al) alloys on the corrosion behavior was studied at two temperatures (400 °C and 1200 °C). For the Fe-21Cr alloy, Cr 2 O 3 layer was formed upon exposure to both temperatures. The addition of Al altered the corrosion mechanism of the alloy. At 1200 °C, a thin α-Al 2 O 3 is formed on the Fe-21Cr-5.5Al alloy. Whereas, at low temperature, a continuous Cr 2 O 3 is formed at the top with an internal Al 2 O 3 layer. These results show that FeCrAl alloys hold promise as Fuel Cladding Materials with Al playing a crucial role under operational as well as accident-like conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Electrodeposition of Fe–Ni alloy on Au(111) substrate: Metastable BCC growth via hydrogen evolution and interactions

The electrodeposition of Fe–Ni alloy is usually complicated by the effects of anomalous codeposition and hydrogen evolution. Although the influence of the deposition conditions on the alloy composition has been studied extensively, very few works considered the influence of growth conditions on the phase constitution. In this work, various electrodeposition conditions were investigated to grow Fe–Ni alloy films (<30 nm) with similar compositions in the Invar-to-equiatomic range on Au (111) substrate. Highly (110) oriented BCC phase Fe–Ni with a Ni fraction (ca. 40 at.% Ni) well beyond the equilibrium solubility limit (5 at.% Ni) was obtained with a significant alloy deposition partial current. An increase in the fraction of the BCC phase was found to be associated with a higher alloy deposition partial current, but not necessarily with an increase in the hydrogen evolution partial current. Motivated by the findings from this work, the formation of the metastable BCC phase is speculated to depend on the competing kinetics between the inclusion and desorption of hydrogen adatoms at the electrodeposited growth front.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Cost-efficient copper-nickel alloy for active cooling applications

It is recently proposed that active (Peltier) and passive (conductive) cooling could be combined to design highly-efficient thermal conductors as active heat sinks. Here we study the potential of low-cost copper-nickel alloys for active cooling applications. We show that for this application, copper-nickel alloys prepared using industrial-grade powders to lower the manufacturing cost, are as good as copper-nickel alloys made out of high purity metals. Furthermore, directed energy deposition, a type of additive manufacturing, can produce copper-nickel alloys which have about 10 percent lower thermoelectric power factor compared to mechanical-alloying methods but have larger thermal conductivity values, hence, possessing similar effective thermal conductivity values, reaching 403 W m -1 K -1 at 390K. Much larger values are expected at higher temperatures. The usage of additive manufacturing enables complex geometries and large-scale production.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dual-scale folding in cutting of commercially pure aluminum alloys

We examine a, hitherto, little-studied and curious machining chip morphology, with tell-tale signs of folding at two different length scales, that is common in cutting of certain ductile and highly strain-hardening metals like soft aluminum alloys, tantalum and niobium. This chip morphology does not appear in the usual catalogues of common chip types. The mechanics of formation of the “dual-scale folded chip” is studied in model material systems of commercially pure aluminum alloys (AA 1100 and AA 8040), that prominently exhibit this chip morphology. The flow, folding and associated plastic instabilities are investigated using micro/macro structure observations of the chip in a plane-strain cutting framework, with high-speed in situ imaging and image analysis of material flow; and force measurements. The smaller-scale folding is shown to develop in the primary deformation zone while the larger-scale folding occurs as the chip traverses the rake face of the tool. The resulting chip is composed of irregularly-spaced large folds, superimposed onto which are the quasi periodic small folds. The representative wavelengths of the two folds differ on average by an order of magnitude, 0.1 mm vs. 2 mm. The observations reveal a direct coupling between the material flow and chip morphology, and how specific attributes of the dual-scale folded chip arise from the flow mechanism. Plastic buckling is found to play a key role in the folding at both length scales. The small-scale folds are characteristic of a sinuous plastic flow mode, while the large-scale folding is characterized by buckling and stick-slip along the tool rake face, triggered by adhesive pinning of the chip to the tool. Important consequences of the dualscale folding are very large cutting forces, and force oscillations of large amplitude, despite the alloys being very soft, only ~ 25 HV. Here, the dual-scale folding is why many of these alloys are classified as “gummy” to machine. Since the dual-scale folded chip is associated with large cutting forces and poor surface quality, there is much to be gained by disrupting this flow type in practical machining applications. Methods for controlling the folding to improve machining performance with the gummy alloys are briefly discussed.

36 MATERIALS SCIENCE↗