Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “UNLOADING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Flexibility effects on tooth contact location in spiral bevel gear transmissions

An analytical method to predict the shift of the contact ellipse between the meshing teeth in a spiral bevel gear set is presented in this report. The contact ellipse shift of interest is the motion of the nominal tooth contact location on each tooth from the ideal pitch point to the point of contact between the two teeth considering the elastic motions of the gears and their supporting shafts. This is the shift of the pitch point from the ideal, unloaded position on each tooth to the nominal contact location on the tooth when the gears are fully loaded. It is assumed that the major contributors of this motion are the elastic deflections of the gear shafts, the slopes of the shafts under load and the radial deflections of the four gear shaft bearings. The motions of the two pitch point locations on the pinion and the gear tooth surfaces are calculated in a FORTRAN program which also calculates the size and orientation of the Hertzian contact ellipse on the tooth faces. Based on the curvatures of the two spiral bevel gear teeth and the size of the contact ellipse, the program also predicts the basic dynamic capacity of the tooth pair. A complete numerical example is given to illustrate the use of the program.

Altidis, P. C.↗

Osteoblast histogenesis in periodontal ligament and tibial metaphysis during simulated weightlessness

Utilizing the nuclear morphometric assay for osteoblast histogenesis, the effect of simulated weightlessness (SW) on the relative numbers of the periodontal ligament (PDL) osteoblast progenitors and on the total number of osteogenic cells was determined in rats. Weightlessness was simulated by subjecting rats to continuous 30-deg head-down posture using a modified back-harness device of Morey (1979). The response of a partially unloaded, weight-bearing bone, tibial primary spongiosa (PS), was compared to a normally loaded, nonweight-bearing PDL bone. Data indicated a similar differentiation sequence in PS and PDL, which suggests that these bones might be sensitive to the same systemic factors. Preosteoblast numbers were seen to decrease in both nonweight-bearing and weight-bearing bones during SW (compared with rats not exposed to SW), indicating the importance of systemic mediators, such as cephalad fluid shift, physiological stress, and/or growth retardation.

Fielder, Paul J.↗

Lessons learned from the DC-10 carbon-epoxy rudder program

With the DC-10 carbon-epoxy rudder, the Douglas Aircraft Company achieved one of the greatest percentage weight savings associated with composite structures. Apart from minor damage from lightning strikes, the 15 rudders put into service have experienced virtually trouble-free operation for about a decade. This paper explains why a multirib, postbuckled skin design was used for the DC-10 composite rudder, how it was justified, and how it would have compared with more conventional sandwich design concepts. Special attention is devoted to the reasons why, for such postbuckled designs, it is better to allow the skin to wrinkle and unload itself than to reinforce it and make it resist buckling until some higher load level is attained. With minor changes in the manufacturing technique, this design concept is ideal for the control surfaces on many aircraft. The paper includes suggestions on how to make even better composite control surfaces in the future.

Hart-Smith, L. J.↗

Deformation of a metal-matrix tensile coupon with a central slot - An experimental study

A metal-matrix specimen was investigated using high-sensitivity moire interferometry. In-plane displacement fields were analyzed at various load levels from 15 to 95 percent of the failure load. Normal and shear strains were determined from displacement gradients. Highly localized plastic slip zones occured in the ductile aluminum matrix tangent to the ends of the slot. Shear strains in the slip zone were an order of magnitude greater than the largest normal strains in the specimen. The shear-strain concentration factor rose dramatically with the onset of plastic slip and continued to rise gradually with load to 95 percent of the failure load. Upon unloading, shear strains in the slip zone remained precariously high.

Post, Daniel↗

A miniature remote deadweight calibrator

A miniature, computer-controlled, deadweight calibrator was developed to remotely calibrate a force transducer mounted in a cryogenic chamber. This simple mechanism allows automatic loading and unloading of deadweights placed onto a skin friction balance during calibrations. Equipment for the calibrator includes a specially designed set of five interlocking 200-milligram weights, a motorized lifting platform, and a controller box taking commands from a microcomputer on an IEEE interface. The computer is also used to record and reduce the calibration data and control other calibration parameters. The full-scale load for this device is 1,000 milligrams; however, the concept can be extended to accommodate other calibration ranges.

Supplee, Frank H., Jr.↗

Analyzing Commonality In A System

Cost decreased by use of fewer types of parts. System Commonality Analysis Tool (SCAT) computer program designed to aid managers and engineers in identifying common, potentially common, and unique components of system. Incorporates three major functions: program for creation and maintenance of data base, analysis of commonality, and such system utilities as host-operating-system commands and loading and unloading of data base. Produces reports tabulating maintenance, initial configurations, and expected total costs. Written in FORTRAN 77.

Pacheco, Alfred↗

Device Rotates Bearing Balls For Inspection

Entire surface of ball inspected automatically and quickly. Device holds and rotates bearing ball for inspection by optical or mechanical surface-quality probe, eddy-current probe for detection of surface or subsurface defects, or circumference-measuring tool. Ensures entire surface of ball moves past inspection head quickly. New device saves time and increases reliability of inspections of spherical surfaces. Simple to operate and provides quick and easy access for loading and unloading of balls during inspection.

Burley, R. K.↗

Mechanisms of rolling contact spalling

The results of a study aimed at analyzing the mechanical material interactions responsible for rolling contact spalling of the 440 C steel, high pressure oxygen turbopump bearings are presented. A coupled temperature displacement finite element analysis of the effects of friction heating under the contact is presented. The contact is modelled as a stationary, heat generating, 2 dimensional indent in an elastic perfectly plastic half-space with heat fluxes up to 8.6 x 10000 KW/m sq comparable to those generated in the bearing. Local temperatures in excess of 1000 C are treated. The calculations reveal high levels of residual tension after the contact is unloaded and cools. Efforts to promote Mode 2/Mode 3 fatigue crack growth under cyclic torsion in hardened 440 C steel are described. Spalls produced on 440 C steel by a 3 ball/rod rolling contact testing machine were studied with scanning microscopy. The shapes of the cyclic, stress strain hysteresis loops displayed by hardened 440 C steel in cyclic torsion at room temperature are defined for the plastic strain amplitudes encountered in rolling/sliding contact. Results of these analyses are discussed in detail.

Kumar, A. M.↗

Cyclic uniaxial and biaxial hardening of type 304 stainless steel modeled by the viscoplasticity theory based on overstress

The isotropic theory of viscoplasticity based on overstress does not use a yield surface or a loading and unloading criterion. The inelastic strain rate depends on overstress, the difference between the stress and the equilibrium stress, and is assumed to be rate dependent. Special attention is paid to the modeling of elastic regions. For the modeling of cyclic hardening, such as observed in annealed Type 304 stainless steel, and additional growth law for a scalar quantity which represents the rate independent asymptotic value of the equilibrium stress is added. It is made to increase with inelastic deformation using a new scalar measure which differentiates between nonproportional and proportional loading. The theory is applied to correlate uniaxial data under two step amplitude loading including the effect of further hardening at the high amplitude and proportional and nonproportional cyclic loadings. Results are compared with corresponding experiments.

Yao, David↗

Critical Joints in Large Composite Primary Aircraft Structures. Volume 3: Ancillary Test Results

A program was conducted to develop the technology for critical structural joints for composite wing structure that meets all the design requirements of a 1990 commercial transport aircraft. The results of a comprehensive ancillary test program are summarized, consisting of single-bolt composite joint specimens tested in a variety of configurations. These tests were conducted to characterize the strength and load deflection properties that are required for multirow joint analysis. The composite material was Toray 300 fiber and Ciba-Geigy 914 resin, in the form of 0.005 and 0.01 inch thick unidirectional tape. Tests were conducted in single and double shear for loaded and unloaded hole configurations under both tensile and compressive loading. Two different layup patterns were examined. All tests were conducted at room temperature. In addition, the results of NASA Standard Toughness Test (NASA RP 1092) are reported, which were conducted for several material systems.

Bunin, Bruce L.↗

Physiological comparison of rat muscle in body suspension and weightlessness

Hind limb unloading is achieved with whole body suspension (WBS) and with tail suspension (TS). Comparable levels of muscle mass loss and decreases in protein levels result during one to three weeks of exposure to microgravity (microG), WBS, and TS. Losses are most apparent in soleus (S), intermediate in gastrocnemius (G) and least in extensor digigorum longus (EDL). Comparison of S and EDL type I and II fiber changes (numbers and area) after seven days of microG flight and WBS showed, in S, an increase in Type I and Type II fiber density and a decrease in area. Except for a decrease in Type I fiber density in EDL, all other parameters remained comparable. The general conclusions were that the S under microG and WBS responds in a similar manner. The EDL, for the most part, shows little change under both conditions.

Musacchia, X. J.↗

A boundary layer model for magnetospheric substorms

An alternative framework for understanding magnetospheric substorm activity is presented. It is argued that observations of magnetic field and plasma flow variations in the magnetotail can be explained in terms of the passage of the plasma sheet boundary layer over the satellite detecting the tail signatures. It is shown that field-aligned currents and particle acceleration processes on magnetic field lines threading the ionospheric Harang discontinuity lead to the distinctive particle and field signatures observed in the magnetotail during substorms. It is demonstrated that edge effects of field-aligned currents associated with the westward traveling surge can lead to the negative B(z) perturbations observed in the tail that are presently attributed to observations made on the anti-earthward side of a near-earth neutral line. Finally, it is shown that the model can provide a physical explanation of both the driven system and the loading-unloading system whose combined effects provide the observed substorm perturbation pattern in the magnetosphere and ionosphere.

Rostoker, Gordon↗

A review of path-independent integrals in elastic-plastic fracture mechanics

The objective of this paper is to review the path-independent (P-I) integrals in elastic plastic fracture mechanics which have been proposed in recent years to overcome the limitations imposed on the J-integral. The P-I integrals considered are the J-integral by Rice (1968), the thermoelastic P-I integrals by Wilson and Yu (1979) and Gurtin (1979), the J-integral by Blackburn (1972), the J(theta)-integral by Ainsworth et al. (1978), the J-integral by Kishimoto et al. (1980), and the Delta-T(p) and Delta T(p)-asterisk integrals by Alturi et al. (1982). The theoretical foundation of the P-I integrals is examined with an emphasis on whether or not the path independence is maintained in the presence of nonproportional loading and unloading in the plastic regime, thermal gradient, and material inhomogeneities. The simularities, difference, salient features, and limitations of the P-I integrals are discussed. Comments are also made with regard to the physical meaning, the possibility of experimental measurement, and computational aspects.

Kim, Kwang S.↗

Systems integration for the Kennedy Space Center (KSC) Robotics Applications Development Laboratory (RADL)

A laboratory for developing robotics technology for hazardous and repetitive Shuttle and payload processing activities is discussed. An overview of the computer hardware and software responsible for integrating the laboratory systems is given. The center's anthropomorphic robot is placed on a track allowing it to be moved to different stations. Various aspects of the laboratory equipment are described, including industrial robot arm control, smart systems integration, the supervisory computer, programmable process controller, real-time tracking controller, image processing hardware, and control display graphics. Topics of research include: automated loading and unloading of hypergolics for space vehicles and payloads; the use of mobile robotics for security, fire fighting, and hazardous spill operations; nondestructive testing for SRB joint and seal verification; Shuttle Orbiter radiator damage inspection; and Orbiter contour measurements. The possibility of expanding the laboratory in the future is examined.

Davis, V. Leon↗

Problems in analysis of data from muscles of rats flow in space

Comparison of hind-limb muscles of rats flown on Spacelab-3 or tail-traction-suspended showed that 11-17 h reloading postflight might have altered the results. Soleus atrophied; plantaris, gastrocnemius, and extensor digitorum longus grew slower; and tibialis anteiror grew normally. In both flight and simulated soleus and plantaris, higher tyrosine and greater glutamine/glutamate ratio indicated negative protein balance and increased glutamine production, respectively, relative to controls. Aspartate was lower in these muscles. Reloading generally decreased tyrosine, but increased aspartate and glutamine/glutamate. These data showed that 12 h of reloading after flight is characterized by reversal, to varying extents, of the effects of unloading.

Tischler, Marc E.↗

Comparative morphometry of fibers and capillaries in soleus following weightlessness (SL-3) and suspension

This work is a continuation of efforts to assess responses of rat skeletal muscle to weightlessness (W) and earthside laboratory experiments with unloading of hind limbs. The soleus is a slow-twitch, load-bearing (antigravity) muscle. Both exposure to W and to the hypokinesia/hypodynamia of whole-body suspension (WBS) results in soleus atrophy. Cross-sectional areas of both slow- and fast-twitch fibers decrease during 7 days of W or 7 or 14 days of WBS. Density and area changes tended to reverse to control levels during 7 days of recovery (R) following WBS. Capillary density was increased with 7 days of W or 7 or 14 days of WBS. During 7 days of R the capillary density returned toward control levels. In summary, the reduction in fiber cross-sectional areas and the increase in fiber and capillary densities support the hypothesis that in both W and WBS there is a loss in soleus muscle cell mass and not in fiber numbers.

Musacchia, X. J.↗

Tooth Contact Shift in Loaded Spiral Bevel Gears

An analytical method is presented to predict the shifts of the contact ellipses of spiral bevel gear teeth under load. The contact ellipse shift is the motion of the tooth contact position from the ideal pitch point to its location under load. The shifts are due to the elastic motions of the gear and pinion supporting shafts and bearings. The calculations include the elastic deflections of the gear shafts and the deflections of the four shaft bearings. The method assumes that the surface curvature of each tooth is constant near the unloaded pitch point. Results from these calculations will help designers reduce transmission weight without seriously reducing transmission performance.

Savage, M.↗

The vertical structure of arch filament systems in solar emerging flux regions

The paper studies the vertical velocity of arch filaments in emerging flux regions by measuring their proper motion near the limb in H-alpha filtergrams and their radial velocity near the disk center in H-alpha spectrograms. Both show that arch filaments rise at a velocity between 10 and 15 km/s. The possible mechanisms producing this high velocity are discussed. None of them is satifactory, but it appears that the unloading of the arches by outflow must play a role. From the strength of H-alpha emission and D3 absorption, the temperature of arch filaments is estimated at 6000-15,000 K and the density at 10 to the 11th-12th/cu cm.

Chou, Dean-Yi↗