Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Storage capacity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

High-Performance Li-Ion Battery Anodes from Electrospun Nanoparticle/Conducting Polymer Nanofibers

The project objectives were: (1) Fabricate, characterize, and optimize the composition/morphology of an entirely new class of Si-based nanofiber anodes for Li-ion batteries, with high gravimetric and volumetric energy density and minimal capacity fade during charge/discharge cycling, (2) Improve our understanding of structure/functions correlations in electrospun particle/conducting polymer nanofiber anodes, and (3) Perform pilot-scale-up studies for anode commercialization.

25 ENERGY STORAGE↗
DOE OSTI2024

Aboveground Storage Tank Closure Report: Tank TA-55-0560

This project Aboveground Storage Tank Closure Report details tank-removal activities conducted in Technical Area-55 (TA-55) of the Los Alamos National Laboratory (LANL or the Laboratory), specifically removal of Aboveground Storage Tank (AST) TA-55-0560, NMED PSTB Facility ID #54763; a 12,000-gallon-capacity aboveground diesel-fuel storage tank.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Communication — The Impact of Co-solvent Selection for Dimethyl-2,5-dioxahexane carboxylate in Sodium Ion Batteries

Traditional linear carbonates including dimethyl carbonate (DMC), diethyl carbonate (DEC), and ethyl methyl carbonate (EMC) were investigated as co-solvents for the dimethyl-2,5-dioxahexane carboxylate (DMOHC)-based electrolyte in Na 0.97 Ca 0.03 [Mn 0.39 Fe 0.31 Ni 0.22 Zn 0.08 ]O 2 (NCMFNZO)/hard carbon (HC) pouch cells. The EMC-containing cell displays excellent electrochemical performance, exhibiting only a 1.6 mAh irreversible capacity loss during 500 h of storage at 4 V and 40 °C, and maintaining over 80% capacity retention after 200 cycles up to 4 V at 40 °C. Severe gas evolution and Na plating issues are present in all the tested systems.

25 ENERGY STORAGE↗
DOE OSTI2020

Solution scattering at the Life Science X-ray Scattering (LiX) beamline

This work reports the instrumentation and software implementation at the Life Science X-ray Scattering (LiX) beamline at NSLS-II in support of biomolecular solution scattering. For automated static measurements, samples are stored in PCR tubes and grouped in 18-position sample holders. Unattended operations are enabled using a six-axis robot that exchanges sample holders between a storage box and a sample handler, transporting samples from the PCR tubes to the X-ray beam for scattering measurements. The storage box has a capacity of 20 sample holders. At full capacity, the measurements on all samples last for ∼9 h. For in-line size-exclusion chromatography, the beamline-control software coordinates with a commercial high-performance liquid chromatography (HPLC) system to measure multiple samples in batch mode. The beamline can switch between static and HPLC measurements instantaneously. In all measurements, the scattering data span a wide q -range of typically 0.006–3.2 Å −1 . Functionalities in the Python package py4xs have been developed to support automated data processing, including azimuthal averaging, merging data from multiple detectors, buffer scattering subtraction, data storage in HDF5 format and exporting the final data in a three-column text format that is acceptable by most data analysis tools. These functionalities have been integrated into graphical user interfaces that run in Jupyter notebooks, with hooks for external data analysis software.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Cu Doping Increases Capacity Retention in LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) by Altering the Potential of the Ni-Based Redox Couple and Inhibiting Particle Pulverization

To discern the influence of Cu 2+ as a dopant on both the structural and electrochemical characteristics of LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622), Cu 2+ (aq) was added to the coprecipitation synthesis from the constituent ions. At 5 mol % Cu 2+ , a single-phase Cu-NMC product results, evidenced by an increase in d-spacing along the [003] and [104] directions and a slight increase in the crystal volume of the R–3m hexagonal (rock-salt superstructure) lattice. XRD data and high-resolution TEM imaging support Cu 2+ doping primarily on the transition metal 3b Wyckoff sites. Here, galvanostatic cycling of Cu-NMC shows a reversible gravimetric capacity of 102 mAh/g compared to 136 mAh/g for undoped NMC. Despite the lower capacity, the discharge capacity retention of Cu-NMC is 89% after 100 cycles compared to only 70% for NMC. XPS analysis reveals that this lower capacity is due to an increase in the concentration of Ni 3+ ions at the surface, while XRD data collected at the top and bottom of charge show a smaller decrease in crystalline domain size for Cu-NMC (40.5% decrease) compared to NMC (74.7% decrease), translating to pulverization of the secondary particles.

25 ENERGY STORAGE↗
DOE OSTI2025

Driving the grid forward: How electric vehicle adoption shapes power system infrastructure and emissions

We model the effect of plug-in electric vehicle (EV) adoption on U.S. power system generator capacity investment, operations, and emissions through 2050 by estimating power systems outcomes under a range of EV adoption trajectory scenarios. Our EV adoption scenarios are informed by 1) an Energy Information Administration scenario with no policy intervention, 2) EV growth expected under the Inflation Reduction Act (IRA), 3) a Biden Administration 50% EV sales target by 2030, 4) the Environmental Protection Agency’s projections under vehicle emissions standards, and 5) the International Energy Agency’s roadmap to Net Zero by 2050. We find across these scenarios that increasing EV adoption induces investment in new wind, solar, storage, and natural gas capacity, affecting power generation mix and emissions. The net effect of increasing EV adoption beyond our IRA base case is to increase power sector emissions by about 5 mtCO 2 eq per EV-year in 2026 (comparable to displaced gasoline vehicle combustion emissions), but this effect rapidly drops to annual levels below 1 mtCO 2 eq per EV-year by 2032 and continues below this level through 2050. Consequential effects of EV adoption vary regionally, with most regions primarily increasing wind or solar capacity and some regions primarily increasing natural gas capacity, even in 2050. Our national emissions estimates per EV-year are relatively robust to the level of EV adoption beyond our baseline and to variation in assumptions about power systems, EV behavior, and policy.

Science & Technology - Other Topics↗
DOE OSTI2022

Revisiting the capacity-fading mechanism of P2-type sodium layered oxide cathode materials during high-voltage cycling

We report P2-type sodium layered oxide cathode (Na 2/3 Ni 1/3 Mn 2/3 O 2 , P2-NNMO) has attracted great attention as a promising cathode material for sodium ion batteries because of its high specific capacity. However, this material suffers from a rapid capacity fade during high-voltage cycling. Several mechanisms have been proposed to explain the capacity fade, including intragranular fracture caused by the P2-O2 phase transion, surface structural change, and irreversible lattice oxygen release. Here we systematically investigated the morphological, structural, and chemical changes of P2-NNMO during high-voltage cycling using a variety of characterization techniques. It was found that the lattice distortion and crystal-plane buckling induced by the P2-O2 phase transition slowed down the Na-ion transport in the bulk and hindered the extraction of the Na ions. The sluggish kinetics was the main reason in reducing the accessible capacity while other interfacial degradation mechanisms played minor roles. Our results not only enabled a more complete understanding of the capacity-fading mechanism of P2-NNMO but also revealed the underlying correlations between lattice doping and the moderately improved cycle performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Developing A New NG Super-Absorbent Polymer (NG-SAP) for a Practical NG Storage System with Low Pressure, Ambient Temperature, and High Energy Density

This R&D project proposed a systematical study to develop a new class of NG super-absorbent polymer (NG-SAP) with the objective to achieve similar CNG volumetric storage level ~250 cm 3 -STP/cm 3 and fast sorption-desorption kinetics at ambient temperature but lower operational pressure (<100 bar). We suggested two consecutive research phases, including (i) a systematical investigation of various polymer systems to identify the suitable classes that can exhibit methane (C1) binding energy in the range of 20-25 kJ/mol and then (ii) focusing on the potential class polymers to identify the specific structure and morphology that can achieve the project objective.In first research phase (1st year), the major tasks included design and synthesis of several representative polymers with various structure attributes, examining their molecular structures, pore morphology, and BET surface area as the prepared samples, and then studying their C1 binding energy and sorption capacity.

03 NATURAL GAS↗
DOE OSTI2024

Importance of High Valence Element Nb in Ni-Rich Layered Cathodes for High-Voltage Lithium-Metal Batteries

Ni-rich layered cathode materials have attracted extensive attention due to their higher energy density and technological maturity in commercialization. As the nickel content is raised, especially surpassing 80%, the increased energy density comes with the tradeoff of diminished thermal stability and increased electrochemical structural instability of the cathode. Compared with Co, Al, B, and Ta, the introduction of high valence element Nb significantly improved the electrochemical cycling, delivering a capacity of 202 mAh/g, corresponding to a capacity retention of 92% after 200 cycles tested at 45 °C. Further, the ex situ differential scanning calorimetry and in situ isothermal microcalorimetry demonstrate that the Nb-modified cathode has the potential to enhance the safety of ultrahigh nickel (Ni) NMCs and displays remarkable resilience to extensive cycling by inhibiting high-temperature decomposition reactions and exhibiting a lower heat flow during electrochemical cycling.

25 ENERGY STORAGE↗
NASA NTRS1984

Design concept definition study for an improved shuttle waste collection subsystem

A no-risk approach for developing an Improved Waste Collection Subsystem (WCS) for the shuttle orbiter is described. The GE Improved WCS Concept builds on the experience of 14 Shuttle missions with over 400 man-days of service. This concept employs the methods of the existing flight-proven mature design, augmenting them to eliminate foreseen difficulties and to fully comply with the design requirements. The GE Improved WCS Concept includes separate storage for used wipes. Compaction of the wipes provides a solution to the capacity problem, fully satisfying the 210 man-day storage requirement. The added feature of in-flight serviceable storage space for the wipes creates a variable capacity feature which affords redundancy in the event of wipes compaction system failure. Addition of features permitting in-flight servicing of the feces storage tank creates a variable capacity WCS with easier post-flight servicing to support rapid turnaround of the Shuttle orbiter. When these features are combined with a vacuum pump to evacuate wipes and fecal storage tanks through replaceable odor/bacteria filters to the cabin, the GE Improved WCS satisfies the known requirements for Space Station use, including no venting to space.

Source record↗
NASA NTRS2004

Polymer/Silicate Nanocomposites Used to Manufacture Gas Storage Tanks With Reduced Permeability

Over the past decade, there has been considerable research in the area of polymer-layered silicate nanocomposites. This research has shown that the dispersion of small amounts of an organically modified layered silicate improves the polymer strength, modulus, thermal stability, and barrier properties. There have been several reports on the dispersion of layered silicates in an epoxy matrix. Potential enhancements to the barrier properties of epoxy/silicate nanocomposites make this material attractive for low permeability tankage. Polymer matrix composites (PMCs) have several advantages for cryogenic storage tanks. They are lightweight, strong, and stiff; therefore, a smaller fraction of a vehicle's potential payload capacity is used for propellant storage. Unfortunately, the resins typically used to make PMC tanks have higher gas permeability than metals. This can lead to hydrogen loss through the body of the tank instead of just at welds and fittings. One approach to eliminate this problem is to build composite tanks with thin metal liners. However, although these tanks provide good permeability performance, they suffer from a substantial mismatch in the coefficient of thermal expansion, which can lead to failure of the bond between the liner and the body of the tank. Both problems could be addressed with polymersilicate nanocomposites, which exhibit reduced hydrogen permeability, making them potential candidates for linerless PMC tanks. Through collaboration with Northrop Grumman and Michigan State University, nanocomposite test tanks were manufactured for the NASA Glenn Research Center, and the helium permeability was measured. An organically modified silicate was prepared at Michigan State University and dispersed in an epoxy matrix (EPON 826/JeffamineD230). The epoxy/silicate nanocomposites contained either 0 or 5 wt% of the organically modified silicate. The tanks were made by filament winding carbon fibers with the nanocomposite resin. Helium permeability was measured by Northrop Grumman, showing that the leak rate/day of the nanocomposite matrix tank was approximately 80-percent less than that of the neat epoxy matrix tank.

Campbell, Sandi G.↗
DOE OSTI2024

Enabling thermal energy storage in structural cementitious composites with a novel phase change material microcapsule featuring an inorganic shell and a bio-inspired silica coating

Phase change material (PCM) microcapsules offer a promising approach for integrating PCM into building materials for efficient thermal energy storage. Here, this study presents the development of a novel PCM microcapsule specifically designed for incorporation into cementitious materials. The microcapsule consists of a low-cost PCM core derived from vegetable oil by-products and a durable inorganic shell made from cenosphere, a hollow fly ash generated from coal burning power plants. A novel process is developed to apply a silica coating to these cenosphere-based PCM microcapsules (CPCM), resulting in bioinspired-silica-coated CPCM microcapsules (BCPCM). This coating process draws inspiration from marine microorganism-based silica production and utilizes low-cost sodium silicate as a precursor, enabling eco-friendly and cost-effective manufacturing at ambient temperature and mild pH conditions. The morphology, chemical stability, and thermal properties of the BCPCM along with its thermo-mechanical performance in cementitious composites were comprehensively analyzed. Experimental results demonstrate successful silica deposition on BCPCM, leading to enhanced latent heat properties of the produced BCPCM. With the silica coating, BCPCM exhibits a 50 °C delay in thermal decomposition compared to CPCM, enhancing fire resistance and preventing premature PCM leakage of the microcapsule. The bioinspired silica coating effectively restores over 10% of the strength loss for each percent increase in CPCM incorporated into the mortar. The thermal performance experiments reveal that increasing the BCPCM content reduces temperature peaks and rates of temperature increase, indicating an improved capacity for thermal energy storage. This new PCM microcapsule provides a cost-effective solution to integrate thermal energy storage to cementitious material, as evidenced that over 30% of aggregates (in volume) can be replaced by the microcapsule without a drastic loss of strength.

25 ENERGY STORAGE↗
DOE OSTI2020

In Operando XANES Imaging of High Capacity Intermetallic Anodes for Lithium Ion Batteries

In operando 2D X-ray absorption near edge structure (XANES) imaging was performed near the Cu K-edge during cycling of Cu 6 Sn 5 composite anodes for lithium ion batteries. Galvanostatic lithiation and delithiation with intermittent constant voltage holds near reaction plateaus show evolution of absorption spectra for active material particles. XANES spectra obtained from images taken during cycling were compared to standard spectra for Cu, Cu 6 Sn 5 , and Li 2 CuSn. Chemical composition was assessed for Cu-containing phases. Distinct Cu, Cu 6 Sn 5 , and Li 2 CuSn regions were identified for each voltage plateau. Mechanical degradation, electrode particle fracture and expansion were observed during delithiation. Furthermore, movement of particles during cycling suggests that expansion also impacts the supporting secondary phases and the transport networks therein. These results demonstrate that spectroscopic X-ray imaging methods can clearly distinguish chemically distinct phases in alloy electrodes and have the versatility to observe the evolution of these phases during lithiation and delithiation.

25 ENERGY STORAGE↗
DOE OSTI2023

Knowledge-driven design of solid-electrolyte interphases on lithium metal via multiscale modelling

Abstract Due to its high energy density, lithium metal is a promising electrode for future energy storage. However, its practical capacity, cyclability and safety heavily depend on controlling its reactivity in contact with liquid electrolytes, which leads to the formation of a solid electrolyte interphase (SEI). In particular, there is a lack of fundamental mechanistic understanding of how the electrolyte composition impacts the SEI formation and its governing processes. Here, we present an in-depth model-based analysis of the initial SEI formation on lithium metal in a carbonate-based electrolyte. Thereby we reach for significantly larger length and time scales than comparable molecular dynamic studies. Our multiscale kinetic Monte Carlo/continuum model shows a layered, mostly inorganic SEI consisting of LiF on top of Li 2 CO 3 and Li after 1 µs. Its formation is traced back to a complex interplay of various electrolyte and salt decomposition processes. We further reveal that low local Li + concentrations result in a more mosaic-like, partly organic SEI and that a faster passivation of the lithium metal surface can be achieved by increasing the salt concentration. Based on this we suggest design strategies for SEI on lithium metal and make an important step towards knowledge-driven SEI engineering.

25 ENERGY STORAGE↗
DOE OSTI2025

Two-Dimensional Siloxene Nanosheets: Understanding the Effect of Heat Treatment on the Surface Chemistry and Resulting Electrochemistry in Lithium-Based Batteries

Two-dimensional (2D) silicon materials are conceptually appealing as negative electrode materials in lithium-ion batteries due to their layered morphology, which can accommodate (de)lithiation-induced volume changes. Herein, heat treatment of 2D Siloxene materials was used to modify the surface functional groups to determine the impact on the electrochemical behavior. Spectroscopic characterization of the heat-treated nanosheets confirmed the loss of oxygenated and hydride surface functional groups with an increased annealing temperature. Formation and disproportionation of the amorphous suboxides with increasing heat treatment were affirmed with lab and synchrotron-based measurements. A reduced irreversible capacity was observed for Siloxene with a higher temperature heat treatment consistent with the formation of a more favorable surface electrolyte interphase (SEI). A Siloxene-400||NMC622 full cell (prepared with 400 °C-annealed Siloxene (Siloxene-400) and LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622)) showed significantly enhanced capacity and rate capability compared to a nano Si||NMC622 cell. Finally, these results illustrate the ability of thermal annealing to modify the surface functional groups of Siloxene and highlight the favorable impact of the appropriate surface functionality on the electrochemistry of Siloxene in lithium cells.

25 ENERGY STORAGE↗
DOE OSTI2020

First-principles Modeling and Design of Solid-State Interfaces for the Protection and Use of Lithium Metal Anodes

Li-ion batteries are one of the most advanced energy storage technologies in use today. Li-ion batteries are used in a multitude of applications ranging from consumer electronics, medical devices, sensors and grid storage. However, improving the capacity and energy density delivered by current Li-ion technology requires advanced materials research into novel chemical systems. In this project we have focused particularly in the use of solid-state electrolytes with lithium metal electrodes. Research into all solid-state batteries (ASSB) with Li metal electrodes has significantly expanded in recent years, however most studies reported experimental findings, which left substantial room for theoretical and modeling work as a tool to understand and determine design principles allowing reliable and safe use of ASSBs with Li metal. Among the remaining obstacles preventing reliable use of ASSBs with a Li metal electrode, the stability of the interface between the solid electrolyte and Li metal, and the propagation/dendrite formation of Li metal and resulting mechanical degradation of the electrolyte are key phenomenon that are yet to be fully understood. In the current project we have addressed these two coupled phenomena using first principles calculations and mesoscale continuum modeling. We have obtained chemical and electrochemical stability windows for several solid electrolyte materials. Additionally, from mathematical and numerical modeling of Li protrusion and dendrite initiation during plating and stripping we have determined design criteria in terms of chemical, electrochemical, and mechanical properties and operating conditions for which stable deposition can occur. We also considered the effects of mixed electronic-ionic conduction in solid electrolytes, which has more recently been suggested as another important mechanism involved in ASSB failure. Throughout our work we have successfully addressed important questions necessary for the use of ASSB’s. We have determined guiding principles for materials properties and operating conditions necessary to operate ASSB’s. And have proposed novel solid electrolyte materials with predicted chemical stability an ionic conductivity. Although this represents significant progress in our understanding, open questions remain in order to fully develop reliable and safely operate ASSBs with Li metal. Future work, building on this project will require further experimental, theoretical and simulation efforts to address remaining questions.

25 ENERGY STORAGE↗
DOE OSTI2024

Impacts of Control, Penetration, and Distribution of Embedded Storage Network in Bulk Power System

The current shift in generation mix from fossil fuel plants towards variable and intermittent renewable energy sources is poised to create a future grid with reduced physical inertia and mismatch between generation and demand. Embedded storage, which is a concept of a coordinated network of storage units sited at the interface between the transmission and distribution system, is proposed as a mechanism to provide a buffer between generation and demand. This paper proposes an automated framework to model and integrate embedded storage in large-scale power systems with industry-grade grid-following (GFL) and grid-forming (GFM) control technologies. More importantly, the developed framework is used to explore the impacts of embedded storage control, penetration, location, and capacity in providing fast frequency response to the grid under contingency events such as generator trips and faults. The framework and study are conducted using the transient-stability simulation tool PSS/E and a realistic model of the Puerto Rico grid as a chosen test system. The simulation results show that GFL and GFM embedded storage, distributed throughout the system, with sufficient penetration and capacity, can effectively improve primary frequency response of the system under the studied contingency events.

Battery Energy Storage, embedded storage, grid-for↗
DOE OSTI2021

Unraveling the Early-Stage Ordering of Krypton Solid Bubbles in Molybdenum: A Multimodal Study

Self-organization of defects such as fission gas bubbles in materials can lead to high inventory capacity for fission gas storage and help mitigate swelling caused by fission gases in nuclear fuel materials under radiation in nuclear reactors. Here, we report the physical mechanism of self-organization of krypton (Kr) gas bubbles in molybdenum (Mo) under ion implantation. The ion fluence and temperature-dependent formation of Kr solid bubble superlattice (SBS) in Mo were investigated by using both synchrotron-based small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM). Early stage self-organization of gas bubbles is observed at a fluence of 2.5 × 10 16 ions/cm 2 at temperatures of 300–400 °C. The bubble lattice constant increases with increasing implantation temperature from 300 to 400 °C. Both experiments and atomic kinetic Monte Carlo modeling indicate that the Kr solid bubbles are weakly ordered in comparison to previously studied helium (He) gas bubble superlattice (GBS) while the lattice constant are relatively smaller for Kr SBS compared to that of He GBS. The irradiation conditions suggest that spinodal decomposition, which is a form of phase separation, probably precedes gas bubble ordering in Mo. Altogether, our work sheds light on the formation mechanism of noble gas superlattice toward the development of radiation-tolerant materials which are important for the design of advanced nuclear reactors.

36 MATERIALS SCIENCE↗