Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Simulation Quality”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Advanced supersonic transport fixed-base simulator evaluations at landing approach

Equations of motion simulating the landing approach case for the supersonic cruise vehicle were programmed and exercised using a fixed base simulation facility. Unaugmented and augmented system comparisons using this facility are provided. Refinements necessary for system performance improvement are made. The unaugmented longitudinal responses to elevator commands are slow and sluggish, requiring augmentation to increase the speed of the response. In the lateral directional case, the Dutch roll is highly underdamped and requires an augmentation system to increase this damping and provide satisfactory flying qualities. The status of this fixed base study is that the longitudinal equations, updated with recent wind tunnel data, were evaluated on the simulator and the system found to be satisfactory. The lateral axis equations are linearized and are not yet updated to large excursion capability; consequently, only limited, preliminary findings on this system are available. The basic results so far indicate augmentation systems are required to provide a satisfactory longitudinal system, and that additional study and evaluation of the lateral directional case are necessary before a more complete assessment can be made.

Feather, J. B.↗
NASA NTRS1991

Comparisons of elastic and rigid blade-element rotor models using parallel processing technology for piloted simulations

A piloted comparison of rigid and aeroelastic blade-element rotor models was conducted at the Crew Station Research and Development Facility (CSRDF) at Ames Research Center. A simulation development and analysis tool, FLIGHTLAB, was used to implement these models in real time using parallel processing technology. Pilot comments and quantitative analysis performed both on-line and off-line confirmed that elastic degrees of freedom significantly affect perceived handling qualities. Trim comparisons show improved correlation with flight test data when elastic modes are modeled. The results demonstrate the efficiency with which the mathematical modeling sophistication of existing simulation facilities can be upgraded using parallel processing, and the importance of these upgrades to simulation fidelity.

Hill, Gary↗
NASA NTRS1991

Comparison of elastic and rigid blade-element rotor models using parallel processing technology for piloted simulations

A piloted comparison of rigid and aeroelastic blade-element rotor models was conducted at the Crew Station Research and Development Facility (CSRDF) at Ames Research Center. A simulation development and analysis tool, FLIGHTLAB, was used to implement these models in real time using parallel processing technology. Pilot comments and qualitative analysis performed both on-line and off-line confirmed that elastic degrees of freedom significantly affect perceived handling qualities. Trim comparisons show improved correlation with flight test data when elastic modes are modeled. The results demonstrate the efficiency with which the mathematical modeling sophistication of existing simulation facilities can be upgraded using parallel processing, and the importance of these upgrades to simulation fidelity.

Hill, Gary↗
NASA NTRSDate not supplied

Uniform Dust Deposition System for Dust Tolerance Studies

Future missions to the Moon will require mechanisms and materials to effectively and reliably operate in the presences of lunar regolith. One of the challenges of developing such technologies is terrestrial testing with lunar dust simulants. Dust has a stochastic nature of depositing and it can be difficult to accurately apply it to surfaces of interest. Deposition density, particles size distribution, and percent coverage are all factors that affect the quality of dust mitigation testing. Therefore, to enable such testing the dust mitigation and seals teams at NASA Glenn Research Center (GRC) have developed a system that can uniformly and repeatably deposit lunar simulants on a range of surfaces. Testing of the Dust Deposition System (DDS) and an associatedsimulant preparation methodology have quantified the levels of uniformity and precision for this system. Furthermore, the deposition system has been paired with automated micrograph capturing and machine learning image analysis to correlate the images of dust on a surface to deposition density (in g/cm2). This correlation alleviates the need for tested samples to be accurately weighed with milligram precision and may be a useful tool for in-situ contamination evaluation on the Moon. This paper covers the design and validation testing for the DDS.

Stephen Gerdts↗
NASA NTRSDate not supplied

Uniform Dust Deposition System for Dust Tolerance Studies

Future missions to the Moon will require mechanisms and materials to effectively and reliably operate in the presences of lunar regolith. One of the challenges of developing such technologies is terrestrial testing with lunar dust simulants. Dust has a stochastic nature of depositing and it can be difficult to accurately apply it to surfaces of interest. Deposition density, particles size distribution, and percent coverage are all factors that affect the quality of dust mitigation testing. Therefore, to enable such testing the dust mitigation and seals teams at NASA Glenn Research Center (GRC) have developed a system that can uniformly and repeatably deposit lunar simulants on a range of surfaces. Testing of the Dust Deposition System (DDS) and an associated simulant preparation methodology have quantified the levels of uniformity and precision for this system. Furthermore, the deposition system has been paired with automated micrograph capturing and machine learning image analysis to correlate the images of dust on a surface to deposition density (in g/cm2). This correlation alleviates the need for tested samples to be accurately weighed with milligram precision and may be a useful tool for in-situ contamination evaluation on the Moon. This paper covers the design and validation testing for the DDS.

Dust↗
NASA NTRS1972

Testing methods and techniques: Testing electrical and electronic devices: A compilation

The methods, techniques, and devices used in testing various electrical and electronic apparatus are presented. The items described range from semiconductor package leak detectors to automatic circuit analyzer and antenna simulators for system checkout. In many cases the approaches can result in considerable cost savings and improved quality control. The testing of various electronic components, assemblies, and systems; the testing of various electrical devices; and the testing of cables and connectors are explained.

Source record↗
NASA NTRS1977

Load and stability measurements on a soft-inplane rotor system incorporating elastomeric lead-lag dampers

An experimental investigation was conducted of the dynamic response and inplane stability associated with a new soft-inplane helicopter rotor. The unique feature of this rotor was the use of an internal elastomeric damper to restrain the blade inplane motion about the lead-lag hinge. The properties of the elastomer were selected to provide both a nominal first inplane frequency ratio of 0.65 and sufficient damping to eliminate the need for additional external damping sources to prevent ground resonance on a typical fuselage structure. For this investigation a 1/5-scale aeroelastic model was used to represent the rotor. The four-blade model had a diameter of 3.05 m (10 ft) and a solidity of 0.103. The first out-of-plane frequency ratio was 1.06. The model was tested in hover and in forward flight up to an advance ratio of 0.45. At each forward speed the rotor lift was varied up to simulated maneuver conditions. The measured rotor loads and response were within acceptable limits, and no adverse response qualities were observed. Moderate out-of-plane hub moments were measured, even for zero lift, to indicate the beneficial control power available for this design. Blade inplane stability testing indicated that the rotor system damping remained at moderate levels throughout the operating envelope.

Weller, W. H.↗
NASA NTRS1980

Ceramic applications in turbine engines

Ceramic material characterization and testing of ceramic nozzle vanes, turbine tip shrouds, and regenerators disks at 36 C above the baseline engine TIT and the design, analysis, fabrication and development activities are described. The design of ceramic components for the next generation engine to be operated at 2070 F was completed. Coupons simulating the critical 2070 F rotor blade was hot spin tested for failure with sufficient margin to quality sintered silicon nitride and sintered silicon carbide, validating both the attachment design and finite element strength. Progress made in increasing strength, minimizing variability, and developing nondestructive evaluation techniques is reported.

Hudson, M. S.↗
NASA NTRS1990

Line parameters for ozone hot bands in the 4.8-micron spectral region

Line positions, intensities, and lower-state energies have been calculated for nine hot bands of (O-16)3 in the 4.8-micron spectral region using improved spectroscopic parameters deduced in recent high-resolution laboratory studies. The good quality of the hot-band parameters has been verified through comparisons of line-by-line simulations with 0.005/cm-resolution laboratory spectra of ozone. The present work and the line parameters calculated for the main bands by Pickett et al. (1988) provide a complete update of ozone spectroscopic parameters in the 4.8 micron region.

Camy-Peyret, Claude↗
NASA NTRS1990

Estimating short-period dynamics using an extended Kalman filter

An extended Kalman filter is used to estimate the parameters of a low-order model from aircraft transient response data. The low-order model is a state-space model derived from the short-period approximation of the longitudinal aircraft dynamics. The model corresponds to the pitch rate to stick force transfer function currently used in flying qualities analysis. The parameters are estimated from flight data as well as from a 6-DOF nonlinear simulation of the aircraft. These two estimates are then compared, and the discrepancies noted. The low-order model is able to satisfactorily match both flight data and simulation data from a high-order computer simulation.

Bauer, Jeffrey E.↗
NASA NTRS1992

High resolution imaging at Palomar

For the last two years we have embarked on a program of understanding the ultimate limits of ground-based optical imaging. We have designed and fabricated a camera specifically for high resolution imaging. This camera has now been pressed into service at the prime focus of the Hale 5 m telescope. We have concentrated on two techniques: the Non-Redundant Masking (NRM) and Weigelt's Fully Filled Aperture (FFA) method. The former is the optical analog of radio interferometry and the latter is a higher order extension of the Labeyrie autocorrelation method. As in radio Very Long Baseline Interferometry (VLBI), both these techniques essentially measure the closure phase and, hence, true image construction is possible. We have successfully imaged binary stars and asteroids with angular resolution approaching the diffraction limit of the telescope and image quality approaching that of a typical radio VLBI map. In addition, we have carried out analytical and simulation studies to determine the ultimate limits of ground-based optical imaging, the limits of space-based interferometric imaging, and investigated the details of imaging tradeoffs of beam combination in optical interferometers.

Kulkarni, Shrinivas R.↗
NASA NTRS1992

Statistical modeling of software reliability

This working paper discusses the statistical simulation part of a controlled software development experiment being conducted under the direction of the System Validation Methods Branch, Information Systems Division, NASA Langley Research Center. The experiment uses guidance and control software (GCS) aboard a fictitious planetary landing spacecraft: real-time control software operating on a transient mission. Software execution is simulated to study the statistical aspects of reliability and other failure characteristics of the software during development, testing, and random usage. Quantification of software reliability is a major goal. Various reliability concepts are discussed. Experiments are described for performing simulations and collecting appropriate simulated software performance and failure data. This data is then used to make statistical inferences about the quality of the software development and verification processes as well as inferences about the reliability of software versions and reliability growth under random testing and debugging.

Miller, Douglas R.↗
NASA NTRS1994

Graphical simulation for aerospace manufacturing

Simulation software has become a key technological enabler for integrating flexible manufacturing systems and streamlining the overall aerospace manufacturing process. In particular, robot simulation and offline programming software is being credited for reducing down time and labor cost, while boosting quality and significantly increasing productivity.

Babai, Majid↗
NASA NTRS1994

X-31 quasi-tailless flight demonstration

The primary objective of the quasi-tailless flight demonstration is to demonstrate the feasibility of using thrust vectoring for directional control of an unstable aircraft. By using this low-cost, low-risk approach it is possible to get information about required thrust vector control power and deflection rates from an inflight experiment as well as insight in low-power thrust vectoring issues. The quasi-tailless flight demonstration series with the X-31 began in March 1994. The demonstration flight condition was Mach 1.2 at 37,500 feet. A series of basic flying quality maneuvers, doublets, bank to bank rolls, and wind-up-turns have been performed with a simulated 100% vertical tail reduction. Flight test and supporting simulation demonstrated that the quasi-tailless approach is effective in representing the reduced stability of tailless configurations. The flights also demonstrated that thrust vectoring could be effectively used to stabilize a directionally unstable configuration and provide control power for maneuver coordination.

Huber, Peter↗
NASA NTRS1994

Merging Intelligent Systems Technologies with CFD Analysis Strategies: Prototype Development at NASA Ames

A collaborative team of researchers from fields of Computational Fluid Dynamics (CFD), fluid physics, computer architectures, and computer science and knowledge engineering have begun work on a prototype system that addresses several of industry's concerns in using NASA-developed CFD codes as part of the design cycle. A major problem exists in the application of CFD technologies within the aeronautics design cycle due primarily to misunderstandings in the ranges of applicability of the various solver codes or turbulence models. Features that arise during the CFD solution process need to be discriminated and recognized as actual flow features with physical support in the geometry and flow conditions of the problem being solved, or as numerical or non-physical errors arising from mis-application of solver code and its parameters, gridding strategies, or discretization. interpolations. The fundamental concept is to develop an intelligent computational system that can accept the engineer's definition of the problem and construct an optimal CFD solution. To do this requires capturing both the knowledge of how to apply the various CFD tools and how to adapt the application of those tools to flow structures as they evolve during the flow simulation. Embedded within this adaptive system approach is the additional desire to automatically identify and quantify the quality of resolution of the pertinent flow structures, be they genuine or error-induced, and then to adjust the solution strategy accordingly. This paper discusses the status of that prototyping effort.

Thompson, David E.↗
NASA NTRS2006

Fast Whole-Engine Stirling Analysis

This presentation discusses the simulation approach to whole-engine for physical consistency, REV regenerator modeling, grid layering for smoothness, and quality, conjugate heat transfer method adjustment, high-speed low cost parallel cluster, and debugging.

Dyson, Rodger W.↗
NASA NTRS2014

Carbon Monitoring System Flux Estimation and Attribution: Impact of ACOS-GOSAT X(CO2) Sampling on the Inference of Terrestrial Biospheric Sources and Sinks

Using an Observing System Simulation Experiment (OSSE), we investigate the impact of JAXA Greenhouse gases Observing SATellite 'IBUKI' (GOSAT) sampling on the estimation of terrestrial biospheric flux with the NASA Carbon Monitoring System Flux (CMS-Flux) estimation and attribution strategy. The simulated observations in the OSSE use the actual column carbon dioxide (X(CO2)) b2.9 retrieval sensitivity and quality control for the year 2010 processed through the Atmospheric CO2 Observations from Space algorithm. CMS-Flux is a variational inversion system that uses the GEOS-Chem forward and adjoint model forced by a suite of observationally constrained fluxes from ocean, land and anthropogenic models. We investigate the impact of GOSAT sampling on flux estimation in two aspects: 1) random error uncertainty reduction and 2) the global and regional bias in posterior flux resulted from the spatiotemporally biased GOSAT sampling. Based on Monte Carlo calculations, we find that global average flux uncertainty reduction ranges from 25% in September to 60% in July. When aggregated to the 11 land regions designated by the phase 3 of the Atmospheric Tracer Transport Model Intercomparison Project, the annual mean uncertainty reduction ranges from 10% over North American boreal to 38% over South American temperate, which is driven by observational coverage and the magnitude of prior flux uncertainty. The uncertainty reduction over the South American tropical region is 30%, even with sparse observation coverage. We show that this reduction results from the large prior flux uncertainty and the impact of non-local observations. Given the assumed prior error statistics, the degree of freedom for signal is approx.1132 for 1-yr of the 74 055 GOSAT X(CO2) observations, which indicates that GOSAT provides approx.1132 independent pieces of information about surface fluxes. We quantify the impact of GOSAT's spatiotemporally sampling on the posterior flux, and find that a 0.7 gigatons of carbon bias in the global annual posterior flux resulted from the seasonally and diurnally biased sampling when using a diagonal prior flux error covariance.

biased sampling↗
NASA NTRS2014

Radiative Heating in MSL Entry: Comparison of Flight Heating Discrepancy to Ground Test and Predictive Models

During the recent entry of the Mars Science Laboratory (MSL), the heat shield was equipped with thermocouple stacks to measure in-depth heating of the thermal protection system (TPS). When only convective heating was considered, the derived heat flux from gauges in the stagnation region was found to be underpredicted by as much as 17 W/sq cm, which is significant compared to the peak heating of 32 W/sq cm. In order to quantify the contribution of radiative heating phenomena to the discrepancy, ground tests and predictive simulations that replicated the MSL entry trajectory were performed. An analysis is carried through to assess the quality of the radiation model and the impact to stagnation line heating. The impact is shown to be significant, but does not fully explain the heating discrepancy.

MSL↗