Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SiC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Trends in SiC MOSFET Threshold Voltage and ON-Resistance Measurements from Thermal Cycling and Electrical Switching Stresses: Preprint

Integrating SiC power MOSFETs is very attractive for advancing power electronic systems, yet the system reliability with new devices remains in question. This work presents two accelerated test experiments to further investigate the packaging and semiconductor failures of a TO-247 SiC MOSFET. First, a variation on power cycling experiments -- switching cycling -- is introduced. Traditional power cycling experiments utilize conduction losses to self-heat the device where a large temperature swing causes degradation at the packaging level. However, by decreasing the on-time such that the device only turns on and immediately turns off, the temperature swing is decreased and the semiconductor itself is degraded. This work shows experimental device degradation caused by continuous switching events - switching cycling, at 90% of the device's breakdown voltage. Second, thermal cycling experiments were conducted between -40 degrees C and 175 degrees C to observe degradation in the mechanical packaging of the device. Experimentally-measured changes in threshold voltage and ON-resistance are recorded in both experiments and compared. These results also illustrate the spectrum between device and package degradation from accelerated test methods.

33 ADVANCED PROPULSION SYSTEMS↗

Hardware Design of a 1.7 kV SiC MOSFET Based MMC for Medium Voltage Motor Drives

Abstract—This paper presents the hardware design of a 7 kV dc bus,1 MVA, 0-1,000 Hz, 1.7 kV SiC MOSFET based medium voltage variable speed drive (MVVSD)1. The system is based on a 7-level three-phase modular multilevel converter (MMC). The full in-depth design, development, and testing of this prototype are provided, including MMC submodule development, arm inductor design, control hardware realization, system integration and thermal analysis. Finally, experimental results demonstrate the excellent performance of the 1.7 kV SiC MOSFET based submodule and the 1 MW, 7 kV MVVSD as a unity in various operation modes

SiC MOSFET, Modular Multilevel Converter, Medium V↗

Preliminary characterization and projections of PVD coatings on SiC cladding for Light Water Reactors

Physical Vapor Deposition (PVD) based CrN, Cr and TiN are currently the leading mitigation coatings for SiC-based Light Water Reactor (LWR) fuel cladding. This manuscript describes the morphology, phase analysis and elemental composition of coatings deposited by commercial vendors on SiC clad materials. The coatings showed continuous crack-free morphology with few microstructural flaws. X-ray analysis and spectroscopy indicated high purity >99.9%. Mechanical tests of coating debonding (by ASTM D4541) and scratch-indentation (by ASTM E2546) were conducted. Strong interface bonding was observed and higher resistance to normal and shear stresses was observed from thicker coatings. Preliminary developments in scratch testing, phase analysis, future needs and expected behavior under irradiation are discussed.

Ang, Caen K.↗

Spatially Resolved Raman Spectroscopy of Thin Carbon Interphase in SiC Ceramic Matrix Composites

A dedicated analysis method is presented to extract the Raman spectrum of an interphase layer thinner than the laser spot size. We focused on spatial correlations between the contrast of optical micrographs and Raman hyperspectral data to predict the constituents of the mixed spectra measured near the interphase. By employing a mapping step size of 0.1 μm, the Raman spectrum of approximately 0.3-μm-thick carbon interphase in a SiC fiber-reinforced SiC matrix composite was extracted from data acquired with a theoretical spot size of about 0.7 μm. Notably, conventional chemometrics procedures were unable to isolate the interphase signal, instead producing a spectrum representing a mixture of interphase and matrix. This study used another composite with approximately 0.9-μm-thick interphase to validate the analysis method, enabling direct measurement of the interphase spectrum. The proposed Raman analysis method has advantages in specimen volume and turnaround time compared to traditional characterization methods, such as transmission electron microscopy. In conclusion, this study also evaluates the applicability of the analysis method to different composite materials and identifies key requirements of the measurements, including the ratio of interphase thickness to spot size and the homogeneity of the surrounding matrix.

ceramic matrix composite↗

Extrinsic Absorption Pathways in Vanadium-Doped SiC Measured Using a Total Internal Reflection Geometry

Vanadium-doped SiC is under study for high-power photoconductive switches and is receiving increased attention as a potential material system for quantum computing, as the V can act as a quantum emitter at telecom wavelengths. Knowledge of the defect-mediated electronic transition pathways from sub-bandgap illumination in this material with low absorption and multi-photon and multi-path transition probability is important in optimizing quantum efficiency. Herein, the optical transitions of vanadium-doped SiC for two polytypes as a function of dopant concentration using a total internal reflection (TIR) geometry are examined. Furthermore, normalized quantum efficiency is reported and correlated with both dopant concentrations (V, N, B, and Al) measured by secondary ion mass spectroscopy (SIMS) and absorption measurements. Although both polytypes respond well to 532 nm light, efficiency at longer wavelengths does not correlate 1:1 with absorption coefficient and strongly depends on the polytype and net background co-dopant concentration. This has important implications for efficient excitation of both carriers for optoelectronics and for the use of V as a quantum emitter.

36 MATERIALS SCIENCE↗

Hall Effect Characterization of α ‐Irradiated p‐Type 4H‐SiC

Most electrical characterization of radiation damage to semiconductors is conducted on full devices or on low‐doped material. However, evaluating the radiation hardness is challenging in less mature semiconductor systems where low‐doped material is unavailable and full devices are difficult to realize. Herein, temperature‐dependent Hall effect measurements are used to demonstrate α particle‐induced radiation effects in p‐type 4H‐SiC with a room temperature hole concentration of . The 4H‐SiC is irradiated by α particles from a 210 Po source over a fluence of –. Modeling the hole concentration as a function of temperature shows that α radiation causes hole compensation through the introduction of hole traps. The radiation also induces a reduction in hole mobility due to an increase in defect‐related scattering centers. At low temperatures and increasingly higher fluences, the conduction mechanism changes from band conduction to another mechanism.

Frye, Clint D.↗

Diamond and SiC Detectors for Rare Event Searches

In recent years, there has been increasing interest in developing detectors which are sensitive to sub-GeV dark matter and low-energy events from coherent neutrino scattering. Due to carbon’s light atomic weight and its tendency to form crystals with high-energy, long-lived phonon modes, carbon-based crystals (including diamond and silicon carbide (SiC)) present themselves as natural target materials for scattering-based searches in this regime. Here, we present our preliminary results in adapting our TES-based detectors to these substrates, specifically 4-H SiC and polycrystalline diamond. We focus on our fabrication efforts, specifically tuning the transition temperature (T C ) of tungsten films sputtered on these materials, as well as our advancement toward fabricating and testing devices on these substrates.

47 OTHER INSTRUMENTATION↗

Magnetic Properties of SiC Monolayer with Different Nonmagnetic Metal Dopants

Magnetic properties of nonmagnetic metal-doped SiC monolayer are studied by the first-principle methods. Different dopants (Al, Ga, Li, Mg, and Na) and doping sites are considered. Similar as transition metal (TM) atoms, magnetic behavior appears in Li-, Mg-, and Na-doped system. In addition, according to the calculated binding energies, the Mg-doped system is the most stable-formed system among the above three magnetic materials. Hence, we study the ferromagnetic interaction in two Mg-doped SiC monolayer. Interestingly, as the increasing Mg–Mg distance, the interaction between two Mg dopants prefers to a long-range FM coupling, which originates from a p-d exchange-like s-p coupling interaction.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electrosynthesis of Ti{sub 5}Si{sub 3}, Ti{sub 5}Si{sub 3}/TiC, and Ti{sub 5}Si{sub 3}/Ti{sub 3}SiC{sub 2} from Ti-Bearing Blast Furnace Slag in Molten CaCl{sub 2}

Ti{sub 5}Si{sub 3}, Ti{sub 5}Si{sub 3}/TiC, and Ti{sub 5}Si{sub 3}/Ti{sub 3}SiC{sub 2} have been electrochemically synthesized from the Ti-bearing blast furnace slag/TiO{sub 2} and/or C mixture precursors at a cell voltage of 3.8 V and 1223 K to 1273 K (950 °C to 1000 °C) in molten CaCl{sub 2}. The pressed porous mixture pellets were used as the cathode, and a solid oxide oxygen-ion-conducting membrane (SOM)-based anode was used as the anode. The phase composition and morphologies of the cathodic products were systematically characterized. The final products possess a porous nodular microstructure due to the interconnection of particles. The variations of impurity elements, i.e., Ca, Mg, and Al, have been analyzed, and the result shows that Ca and Mg can be almost completely removed; however, Al cannot be easily removed from the pellet due to the formation of Ti-Al alloys during the electroreduction process. The electroreduction process has also been investigated by the layer-depended phase composition analysis of the dipped/partially reduced pellets to understand the detailed reaction process. The results indicate that the electroreduction process of the Ti-bearing blast furnace slag/TiO{sub 2} and/or C mixture precursors can be typically divided into four periods, i.e., (i) the decomposition of initial Ca(Mg,Al)(Si,Al){sub 2}O{sub 6}, (ii) the reduction of Ti/Si-containing intermediate phases, (iii) the removal of impurity elements, and (iv) the formation of Ti{sub 5}Si{sub 3}, TiC, and Ti{sub 3}SiC{sub 2}. It is suggested that the SOM-based anode process has great potential to be used for the direct and facile preparation of Ti alloys and composites from cheap Ti-containing ores.

36 MATERIALS SCIENCE↗

Tensile Properties and Fracture Characteristics of Nanostructured Copper and Cu-SiC Nanocomposite Produced by Mechanical Milling and Spark Plasma Sintering Process

The presence of large grains within nanometric and ultrafine grain matrix is an effective method in order to enhance strength while keeping the high ductility of metals. For this purpose, in this research, spark plasma sintering (SPS) was used to consolidate milled Cu and Cu-SiC powders. In SPS process, local sparks with high temperature between particles take place and locally lead to intense grain growth, and therefore, this method has the ability to produce bimodal grain structures in copper and copper-based composites. Microstructural and mechanical studies showed ≈ 185 and ≈ 437 nm matrix grain sizes, high tensile yield strength values of ≈ 188.4 and ≈ 296.9 MPa, and fracture strain values of 15.1 and 6.7% for sintered Cu and Cu-4 vol.% SiC nanocomposite materials, respectively. The presence of nanoparticles promoted the occurrence of static recrystallization and decreased the fraction of coarse grains in microstructure. The high tensile properties of the produced materials are attributed to fine grain size, homogenous dispersion of nanoparticles and retarded grain boundary migration during sintering.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Interaction Between Liquid Silver and Graphene-Coated SiC Substrate

Wettability between liquid Ag and graphene-coated SiC single crystal has been investigated by dispensed drop method at T = 970 °C under vacuum accompanied with subsecond recording of the drop/substrate images (100 frames per second) by high-speed high-resolution CCD camera. Non-contact heating method coupled with capillary purification of the Ag drop procedure has been applied. Scanning electron microscopy combined with EDS analysis and scanning probe microscopy combined with Raman spectroscopy techniques has been utilized for microstructure and surface characterization of samples before and after high-temperature wetting tests. Immediately after its detachment from the capillary, the Ag drop showed non-wetting behavior (θ > 90°) forming a high contact angle of θ = 114°. Surface characterization of the drop surface after wettability tests evidenced the presence of graphene and Si transferred from the substrate to the top of Ag drop. These findings suggest chemical interaction phenomena occurring at the interface. Locally, an intimate contact between liquid Ag and SiC substrate was allowed by the appearance of discontinuities in the graphene layer basically produced by thermomechanical stress. Local dissolution of carbon into liquid Ag and its reorganization (by segregation, nucleation and growth) as secondary graphene layer at the Ag surface was also observed.

36 MATERIALS SCIENCE↗

Design and Performance Evaluation of Al{sub 2}O{sub 3}-SiC Composite for Direct-Bonded Copper Substrate

A computational material design approach is applied to propose a novel ceramic material for direct-bonded copper (DBC) substrate with enhanced thermal and structural performance. The material design inherently consists of many competing requirements that require careful decisions regarding key trade-offs in terms of material composition, inclusion size, shape, and distribution to achieve the target properties. The alumina-silicon (Al{sub 2}O{sub 3}-SiC) composite, as compared to commercial alumina, used in DBC is found to be the most suitable design among other candidates with improved thermal and structural properties. In order to study the performance characteristics and the effects of the new ceramic composite with improved properties in terms of structural behavior and fatigue life of the DBC substrate, the normal working and extreme thermal cycling conditions were simulated and analyzed using finite element method. The temperature, strain, and localized stress distribution within the substrate at a steady-state condition were analyzed, and the improved Coffin–Manson law was used to calculate the fatigue life of the substrate under extreme thermal cycling conditions. The proposed Al{sub 2}O{sub 3}-SiC composite is found to be more robust than the commercial alumina as DBC substrates considering the thermal–mechanical performance. The fatigue life cycle of the DBC substrate with the proposed material is predicted to be about two times longer than the commercial alumina DBC ceramic under transient thermal cycling test.

36 MATERIALS SCIENCE↗

Finite Element Modeling of the Phase Change in Thermally-Grown SiO 2 in SiC Systems for Gas Turbines

The operating lifetimes of SiC-based components in combustion environments are directly linked to the adhesion of the protective environmental barrier coating (EBC) layer. One of the major known failure modes for EBCs is the formation of a thick SiO 2 thermally grown oxide (TGO), which decreases coating adhesion and encourages eventual coating spallation. The effect of the TGO thickness under Yb 2 Si 2 O 7 EBCs on silicon carbide was investigated using finite element models (FEMs) with various interfacial architectures and SiO 2 TGO thicknesses. Further, the FEMs incorporated a user-defined material to simulate the volume contraction of the TGO during the silica phase transformation from β-cristobalite to α-cristobalite upon cooling from the stress-free state at 1350°C to room temperature. Systems with and without a silicon bond coating intermediary layer were assessed. It was shown that the TGO phase transformation stress (1.6–1.7 GPa) dominated the increase in stress in the TGO and EBC layers. Furthermore, it was found that stress increase in the TGO was independent of TGO thickness and interface geometry. These results indicate that stabilization of the TGO to mitigate the phase transformation could dramatically improve the performance of SiC-base components with EBCs.

36 MATERIALS SCIENCE↗

Radiation tolerance of M{sub n+1}AX{sub x} phases, Ti{sub 3}ALC{sub 2} and Ti{sub 3}SIC{sub 2}.

During investigations of novel material types with uses in future nuclear technologies (ITER/DEMO and GenIV fission reactors), ternary carbides with compositions Ti{sub 3}AlC{sub 2} and Ti{sub 3}SiC{sub 2} have been irradiated with high Xe fluences, 6.25 x 10{sup 15} ions cm{sup -2} ({approx}25-30 dpa), using the IVEM-TANDEM facility at Argonne National Laboratory. Both compositions show high tolerance to damage, and give indications that they are likely to remain crystalline to much higher fluences. There is a visible difference in tolerance between Ti{sub 3}AlC{sub 2} and Ti{sub 3}SiC{sub 2} that can be related to the changes in bonding within each material. These initial findings provide evidence for a novel class of materials (+200 compounds) with high radiation resistance, while, significantly, both of these materials are composed of low-Z elements and hence exhibit no long-term activation.

36 MATERIALS SCIENCE↗

The amorphization of 3C-SiC irradiated at moderately elevated temperatures as revealed by X-ray diffraction

Mechanisms of radiation damage buildup in 3C-SiC remain poorly understood. Here, we use X-ray diffraction in combination with numerical simulations to study depth profiles of radiation-produced strain and lattice damage in 3C-SiC bombarded in the temperature range of 25–200 °C with 500 keV Ar ions. Results reveal increased defect recombination with increasing temperature, with a critical amorphization fluence increasing from 0.17 to 0.44 displacements per atom. The amorphization process is found to be correlated with the evolution of lattice strain. We find that, at fluences corresponding to the onset of amorphization, lattice strain is ~2% and is independent of temperature. With continuing bombardment above the onset of amorphization, the strain in the crystal bulk increases and reaches a saturation value that decreases from 7% to 5% with increasing temperature. Based on strain profiles, we compute depth profiles of the effective concentration of point defect clusters in the crystalline phase. Bombardment at higher temperatures results in lower maximum defect concentrations pointing to enhanced defect mobility.

36 MATERIALS SCIENCE↗

Hydride CVD Hetero-epitaxy of B 12 P 2 on 4H-SiC

Icosahedral boron phosphide (B 12 P 2 ) is a wide bandgap semiconductor (3.35 eV) that has been reported to “self-heal” from high-energy electron bombardment, making it attractive for potential use in radioisotope batteries, radiation detection, or in electronics in high radiation environments. Our study focused on improving B 12 P 2 hetero-epitaxial films by growing on 4H-SiC substrates over the temperature range of 1250–1450 °C using B 2 H 6 and PH 3 precursors in a H 2 carrier gas. Furthermore, XRD scans and Laue transmission photographs revealed that the epitaxial relationship was (0001)<11$\bar{2}$0> B 12 P 2 || (0001)<11$\bar{2}$0> 4H-SiC . The film morphology and crystallinity were investigated as a function of growth temperature and growth time. At 1250 °C, films tended to form rough, polycrystalline layers, but at 1300 and 1350 °C, films were continuous and comparatively smooth (R RMS ≤7 nm). At 1400 or 1450 °C, the films grew in islands that coalesced as the films became thicker. Using XRD rocking curves to evaluate the crystal quality, 1300 °C was the optimum growth temperature tested. Finally, at 1300 °C, the rocking curve FWHM decreased with increasing film thickness from 1494 arcsec for a 1.1 μm thick film to 954 arcsec for a 2.7 µm thick film, suggesting a reduction in defects with thickness.

36 MATERIALS SCIENCE↗

Analysis of strain in ion implanted 4H-SiC by fringes observed in synchrotron X-ray topography

A novel high energy implantation system has been successfully developed to fabricate 4H-SiC superjunction devices for medium and high voltage via implantation of dopant atoms with multi-energies ranging from 13 to 66 MeV. The significantly higher levels of energy used compared to conventional implantation processes, necessitates detailed characterization of the lattice damage caused by implantation. To achieve this by employing the novel high energy system, 4H-SiC wafer with 12 μm epilayers were blanket implanted by 13.8–65.7 MeV Al atoms. The lattice damages induced by the implantation were primarily characterized by Synchrotron X-ray Plane Wave Topography (SXPWT) and Reciprocal Space Mapping (RSM). Topographs reveal fringe contrast akin to multiple asymmetric diffraction peaks with an angular separation of only 2″ (arcseconds) observed on rocking curves, indicating inhomogeneous strain distribution across the implanted layer. The strain profile of the implanted layer was extracted from the fringe contrast by applying Rocking-curve Analysis by Dynamical Simulation (RADS). In conclusion, the maximum strain value is similar to that measured on the RSM.

A1. Characterization↗

Investigation of defect formation at the early stage of PVT-grown 4H-SiC crystals

Here, several 4° off-axis 4H-SiC wafers with several hundred microns of initial-stage growth by PVT method are investigated by Synchrotron Monochromatic Beam X-ray Topography (SMBXT). Defect behavior across the seed/newly grown layer interface are demonstrated. Comparison of early stage grown layers to seed sample indicates generation of threading edge dislocation (TED) and threading screw dislocation (TSD)/ threading mixed dislocation (TMD) pairs at the interface while most basal plane dislocations (BPDs) are deflected into TEDs. The (0001) facet of the crystal is already formed at early stage growth at the edge of the wafer and high nitrogen incorporation in facet leads to conditions favorable for nucleation and glide of Shockley/double Shockley faults with layers of 3C-SiC deposited on facet acting as nuclei. Unique-shaped dislocations are observed at early stage growth, which are caused by deflection of TSDs/TMDs and TEDs by macrosteps near the periphery of the sample and the subsequent glide of the a components. The effect of the quality of the seed surface before growth is manifested as randomly oriented arrays of pairs of TEDs and TSDs/TMDs on the as grown surface resulting from residual surface damage from scratches.

36 MATERIALS SCIENCE↗