Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STAINLESS STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Through-Thickness Microstructure Characterization in a Centrifugally Cast Austenitic Stainless Steel Nuclear Reactor Primary Loop Pipe Using Time-of-Flight Neutron Diffraction

The US code of Federal Regulations mandates regular inspection of centrifugally cast austenitic stainless steel pipe, commonly used in primary cooling loops in light-water nuclear power plants. These pipes typically have a wall thickness of ~8 cm. Unfortunately, inspection using conventional ultrasonic techniques is not reliable as the microstructure strongly attenuates ultrasonic waves. Work is ongoing to simulate the behavior of acoustic waves in this microstructure and ultimately develop an acoustic inspection method for reactor inspections. In order to account for elastic anisotropy in the material, the texture in the steel was measured as a function of radial distance though the pipe wall. Experiments were conducted on two 10 × 12.7 × 80 mm radial sections of a cast pipe using neutron diffraction scans of 2 mm slices using the HIPPO time-of-flight neutron diffractometer at the Los Alamos Neutron Science Center (LANSCE, Los Alamos, NM, USA). Strong textures dominated by a small number of austenite grains with their (100) direction aligned in the radial direction of the pipe were observed. ODF analysis indicated that up to 70% of the probed volume was occupied by just three single-grain orientations, consistent with grain sizes of almost 1 cm. Texture and phase fraction of both ferrite and austenite phases were measured along the length of the samples. These results will inform the development of a more robust diagnostic tool for regular inspection of this material.

42 ENGINEERING↗

Phased Array Ultrasonic Sound Field Mapping through Large-Bore Coarse Grained Cast Austenitic Stainless Steel (CASS) Components

A sound field beam mapping exercise was conducted to assist in understanding the effects of coarse-grained microstructures found in cast austenitic stainless steel (CASS) materials on acoustic longitudinal wave propagation. Ultrasonic laboratory measurements were made on three specimens representing four different grain structures. Phased array (PA) probes were fixed on each specimen surface and excited in the longitudinal mode at specific angles while a point receiver was scanned in a raster pattern over the end of the specimen, generating a transmitted sound field image. Three probes operating at nominal frequencies of 0.5, 0.8, and 1.0 MHz were used. A 6.4 mm (0.25-in.) thick slice was removed from the specimen end and beam mapping was repeated three times, yielding four full sets of beam images. Data were collected both with a constant part path for each configuration (probe, specimen and slice, angle, etc.) and with a variable part path (fixed position on the surface). The base specimens and slices were then polished and etched to reveal measureable grain microstructures that were compared to the sound field interactions and scattering effects seen in the collected data.

cast austenitic stainless steel↗

K-shell emission trends from 60 to 130 cm/μs stainless steel implosions

Recent experiments at the 20 MA Z Accelerator have demonstrated, for the first time, implosion velocities up to 110–130 cm/μs in imploding stainless steel wire arrays. These velocities, the largest inferred in a magnetically driven implosion, lead to ion densities of 2 × 10{sup 20} cm{sup −3} with electron temperatures of ∼5 keV. These plasma conditions have resulted in significant increases in the K-shell radiated output of 5–10 keV photons, radiating powers of >30 TW and yields >80 kJ, making it the brightest laboratory x-ray source in this spectral region. These values represent a doubling of the peak power and a 30% increase in the yield relative to previous studies. The experiments also included wire arrays with slower implosions, which were observed to have lower temperatures and reduced K-shell output. These colder pinches, however, radiated 260 TW in the soft x-ray region, making them one of the brightest soft x-ray sources available.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Correlation Between the Pitting Potential Evolution and σ Phase Precipitation Kinetics in the 2205 Duplex Stainless Steel

The aim of this work is to correlate the pitting potential (E{sub pit}) evolution with the kinetics of σ phase precipitation in the 2205 duplex stainless steel aged at 850 °C after solution treatment at 1150 °C. The potentiodynamic polarization curves indicate a reduction of the pitting corrosion resistance with the aging time, which is revealed by a decrease in the E{sub pit} values from 0.65 to 0.40 V{sub SCE}. Thus, E{sub pit} values are used to determine the kinetics parameters of the σ phase precipitation. The experimental transformed fraction agrees well with the one calculated by using the modified Kolmogorov–Johnson–Mehl–Avrami equation with an impingement parameter c = 0.6.

36 MATERIALS SCIENCE↗

Interrogating the Effects of Hydrogen on the Behavior of Planar Deformation Bands in Austenitic Stainless Steel

The effects of internal hydrogen on the deformation microstructures of 304L austenitic stainless steel have been characterized using electron backscattered diffraction (EBSD), transmission Kikuchi diffraction (TKD), high-resolution scanning transmission electron microscopy (HRSTEM), and nanoprobe diffraction. Samples, both thermally precharged with hydrogen and without thermal precharging, were subjected to tensile deformation of 5 and 20 pct true strain followed by multiple microscopic interrogations. Internal hydrogen produced widespread stacking faults within the as-forged initially unstrained material. While planar deformation bands developed with tensile strain in both the hydrogen-precharged and non-precharged material, the character of these bands changed with the presence of internal hydrogen. As shown by nanobeam diffraction and HRSTEM observations, in the absence of internal hydrogen, the bands were predominantly composed of twins, whereas for samples deformed in the presence of internal hydrogen, ε -martensite became more pronounced and the density of deformation bands increased. For the 20 pct strain condition, α '-martensite was observed at the intersection of ε -martensite bands in hydrogen-precharged samples, whereas in non-precharged samples α '-martensite was only observed along grain boundaries. We hypothesize that the increased prevalence of α '-martensite is a secondary effect of increased ε -martensite and deformation band density due to internal hydrogen and is not a signature of internal hydrogen itself.

36 MATERIALS SCIENCE↗

Hot Deformation Behavior and Microstructural Evolution of Antibacterial Austenitic Stainless Steel Containing 3.60% Cu

Hot deformation behavior of as-cast antibacterial austenitic stainless steel containing 3.60% copper was investigated in a temperature range of 900-1150 °C and strain rate range of 0.01-20 s{sup −1}. At strain rates higher than 1 s {sup −1}, the flow stress curves were corrected considering adiabatic heating. Kinetic analysis indicated that the hot deformation activation energy of steel was 376.02 kJ mol{sup −1}. The microstructural evolution under different temperatures was observed by optical microscopy. The nucleation sites for recrystallization and different orientations and twin ratios under different strain rates were analyzed by electron backscatter diffraction. The results showed that hot deformation was dominated by continuous dynamic recrystallization in the high-temperature and high-strain-rate region (1050-1150 °C, 1-20 s{sup −1}). On increasing the temperature and strain rate, the degree of recrystallization and twinning increased simultaneously. These phenomena promoted one another. Thus, the volume fraction of the recrystallized and twinned grains increased with the addition of Cu.

36 MATERIALS SCIENCE↗

Effect of Combined Torsion and Tension on the Microstructure and Fracture Behavior of 316L Austenitic Stainless Steel

In this study, the microstructure evolution and fracture behavior of 316L austenitic stainless steel (ASS) deformed by torsion–tension at room temperature was systematically investigated. During combined tension and torsion, the grain size was refined with increasing shear strain. In addition, the microtexture exhibited a preferred orientation with increasing shear stress. The metastable austenite underwent phase transition when the shear stress increased. The shear stress affected the fracture morphology, and dimples with different sizes and depths were observed for different pre-torsions. The dislocation density increased significantly owing to severe shear deformation. In addition, the dislocation structure evolved and subgrains appeared with the accumulation of shear strain during this combined deformation. The result showed that pre-torsion deformation plays an important role in improving the comprehensive performance and controlling the microstructure evolution of the sample subjected to tension deformation.

36 MATERIALS SCIENCE↗

Microstructural Characterization of Deformation Localization at Small Strains in a Neutron Irradiated 304 Stainless Steel

Deformation localization and structure evolution were investigated in an AISI 304 austenitic stainless steel deformed to 0.8% strain. Using SEM-EBSD, it was shown local plastic deformation may reach significant levels even when the bulk averaged strain level remains below 1%. Local misorientation values up to 24 were observed in these regions of high local plastic deformation. EBSD analysis of FIB lift-out specimens demonstrated that local misorientation level was highest near the free surface and diminished with increasing depth. (S)TEM observations on the same specimen indicated the local density of dislocation channels may vary up to an order of magnitude depending on local grain configuration, distance to the surface and/or local grain boundary structure. It was found that in the case of RT deformation, dislocation defect-free channels may contain twin or may be twin-free with twinning occurring inside channels. Formation of BCC-phase colonies (martensite) was observed in near-surface layer whereas no transformation in the volume of the specimen was detected at this strain level. Martensite formation was associated with channel-grain boundary intersection points where high local misorientation was observed using EBSD.

Deformation↗

Improvement of adhesion and barrier properties of biomedical stainless steel by deposition of YSZ coatings using RF magnetron sputtering

The AISI 316L stainless steel (SS) has been widely used in both artificial knee and hip joints in biomedical applications. In the present study, yttria stabilized zirconia (YSZ, ZrO{sub 2} + 8% Y{sub 2}O{sub 3}) films were deposited on AISI 316L SS by radio-frequency magnetron sputtering using different power densities (50–250 W) and deposition times (30–120 min) from a YSZ target. The crystallographic orientation and surface morphology were studied using X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The effects of the surface modification on the corrosion performance of AISI 316L SS were evaluated in phosphate buffered saline (PBS) solution using an electrochemical test on both the virgin and coated samples. The YSZ coatings have a (111) preferred orientation during crystal growth along the c-axis for short deposition times (30–60 min), whereas a polycrystalline structure forms during deposition times from 90 to 120 min. The corrosion protective character of the YSZ coatings depends on the crystal size and film thickness. A significant increase in adhesion and corrosion resistance by at least a factor of 46 and a higher breakdown potential were obtained for the deposited coatings at 200 W (120 min). - Highlights: • Well-formed and protective YSZ coatings were achieved on AISI 316L SS substrates. • Films grown at high power and long deposition time have polycrystalline structures. • The crystal size varies from ∼ 5 to 30 nm as both power and deposition time increased. • The differences of corrosion resistance are attributed to internal film structure.

36 MATERIALS SCIENCE↗

Physisorption of Ar, Kr, CH4, and N2 on 304 stainless steel at very low pressures.

Determination of physisorption isotherms of these gases on stainless steel by pressure change measurements in very low pressure cryogenic baths where a steel nipple was brought in contact with the test gas at 77 to 90 K in a sealed constant-volume system. The position of the nipple in the gas was changed in such a manner that gas adsorption on a 47.5 sq cm area of the steel surface could be measured. The Dubinin-Radushkevich (DR) equation (1947) was used for an empirical description of isotherms at different temperatures. The mean adsorption energies calculated from the DR plots were 1290, 1545, 1490 and 1903 cal/mol for Ar, Kr, CH4 and N2, respectively, being about 10% higher than the corresponding values on Pyrex.

Troy, M.↗

Fractographic evaluation of creep effects on strain-controlled fatigue-cracking of AISI 304LC and 316 stainless steel

Analysis of high temperature low cycle fatigue of AISI 304LC and 316 stainless steels by the method of strainrange partitioning results in four separate strainrange versus life relationships, depending upon the way in which creep-strain and plastic strain are combined within a cycle. Fractography is used in this investigation of the creep-fatigue interaction associated with these cycles. The PP and PC-cycle fractures were transgranular. The PC-cycle resulted in fewer cycles of initiation and shorter total cyclic life for the same applied inelastic strainrange. The CC-cycle had mixed transgranular and intergranular fracture, fewer cycles of initiation and shorter cycle life than PP or PC. The CP-cycle had fully integranular cracking, and failed in fewer cycles than were required for cracks to initate for PP,PC, and CC.

Oldrieve, R. E.↗

Powder Metallurgy – Hot Isostatic Pressing of 316H Stainless Steel for Nuclear Components

Overview of the PM-HIP work performed on stainless steel 316H as part of the microreactor program. High temperature mechanical testing was performed, with concerns identified with the creep-fatigue performance. Variations in feedstock and processing parameters did not conclusively identify the primary factor in the reduced creep-fatigue performance.

36 - MATERIALS SCIENCE↗

Surface working of 304L stainless steel: Impact on microstructure, electrochemical behavior and SCC resistance

The effect of surface working operations on the microstructure, electrochemical behavior and stress corrosion cracking resistance of 304L stainless steel (SS) was investigated in this study. The material was subjected to (a) solution annealing (b) machining and (c) grinding operations. Microstructural characterization was done using stereo microscopy and electron back scattered diffraction (EBSD) technique. The electrochemical nature of the surfaces in machined, ground and solution annealed condition were studied using potentiodynamic polarization and scanning electrochemical microscopy (SECM) in borate buffer solution. The stress corrosion cracking resistance of 304L SS in different conditions was studied by exposing the samples to boiling MgCl{sub 2} environment. Results revealed that the heavy plastic deformation and residual stresses present near the surface due to machining and grinding operations make 304L SS electrochemically more active and susceptible to stress corrosion cracking. Ground sample showed highest magnitude of current density in the passive potential range followed by machined and solution annealed 304L SS. Micro-electrochemical studies established that surface working promotes localized corrosion along the surface asperities which could lead to crack initiation. - Highlights: Black-Right-Pointing-Pointer Machining/grinding produce extensive grain fragmentation near the surface of 304L SS. Black-Right-Pointing-Pointer Machining/grinding result in martensitic transformation near the surface of 304L SS. Black-Right-Pointing-Pointer Machining/grinding drastically reduce the SCC resistance of 304L SS in chloride. Black-Right-Pointing-Pointer Machining/grinding make the surface of 304L SS electrochemically much more active. Black-Right-Pointing-Pointer SECM study reveal that preferential dissolution takes place along surface asperities.

36 MATERIALS SCIENCE↗

Oxide dispersion strengthened 304 L stainless steel produced by ink jetting and laser powder bed fusion

This paper discusses the fundamentals of a novel hybrid method to synthesize oxide dispersion strengthened (ODS) 304 L stainless steel (SS) alloy using a modified laser powder bed fusion (LPBF) machine. Previously, ODS metal matrix composites have been produced by LPBF via ball-milling, which is expensive to scale. Here, we selectively dope yttria nanoparticles into a SS matrix by jetting a precursor chemistry onto the SS substrate prior to laser conversion and consolidation. Here, the new alloy shows good room temperature mechanical properties. Microstructures are studied using electron microscopy, energy dispersive spectroscopy and electron backscatter diffraction.

36 MATERIALS SCIENCE↗

3D Gel-Printing of TiC-Reinforced 316L Stainless Steel: Influence of the Printing Parameters

In this paper, the composite composed of TiC (35 wt.%) reinforced 316L stainless steel matrix was successfully prepared using a 3D gel-printing (3DGP) process. The “step effect” of 3D printing can be reduced using reasonable parameter settings. The properties of TiC/316L slurry for 3DGP and the influence of the different printing parameters on the surface quality of the samples, such as the extrusion overlaps and printing speed, were researched. The microstructure and fracture morphology of the sintered sample were revealed using scanning electron microscopy. The surface roughness, density, and mechanical properties were also measured. When the internal diameter of the nozzle was 0.50 mm, the result showed that the proper extrusion overlap parameter was 0.08 mm and the maximum printing speed was 20 mm/s. Furthermore, the minimum surface roughness value was 10 μm. After sintering, the mechanical performances were similar to those obtained using a conventional powder metallurgy process.

36 MATERIALS SCIENCE↗