Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STACKING FAULTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Nanostructure formation during accumulative roll bonding of commercial purity titanium

In this investigation, commercial purity titanium (CP–Ti) was subjected to accumulative roll bonding (ARB) process up to 8 cycles (equivalent strain of 6.4) at the ambient temperature. Transmission electron microscopy (TEM) and X–ray diffraction line profile analysis (XRDLPA) were utilized to investigate the microstructure and grain size evolution. Both characterization techniques could clarify the non–uniform microstructure in the early stages and the uniform microstructure in the final stages of the process. The effectiveness of ARB for the fabrication of the nano–grained structure in CP–Ti was revealed. It was found that the SFE is not the only factor affecting grain refinement, as compared with other studies on ARB of FCC materials. Influence of other factors such as the melting temperature and the crystalline structure of the material was determined on the grain refinement. - Highlights: •Nano–grained commercial purity titanium was produced by accumulative roll bonding. •TEM and XRDLPA were used for the characterization of the microstructure. •Important factors affecting the grain size of ARBed materials were discussed.

36 MATERIALS SCIENCE↗

Tensile and high cycle fatigue behaviors of high-Mn steels at 298 and 110 K

Tensile and high cycle fatigue behaviors of high-Mn austenitic steels, including 25Mn, 25Mn0.2Al, 25Mn0.5Cu, 24Mn4Cr, 22Mn3Cr and 16Mn2Al specimens, were investigated at 298 and 110 K. Depending on the alloying elements, tensile ductility of high-Mn steels either increased or decreased with decreasing temperature from 298 to 110 K. Reasonable correlation between the tendency for martensitic tranformation, the critical twinning stress and the percent change in tensile elongation suggested that tensile deformation of high-Mn steels was strongly influenced by SFE determining TRIP and TWIP effects. Tensile strength was the most important parameter in determining the resistance to high cycle fatigue of high-Mn steels with an exceptional work hardening capability at room and cryogenic temperatures. The fatigue crack nucleation mechanism in high-Mn steels did not vary with decreasing tempertature, except Cr-added specimens with grain boundary cracking at 298 K and slip band cracking at 110 K. The EBSD (electron backscatter diffraction) analyses suggested that the deformation mechanism under fatigue loading was significantly different from tensile deformation which could be affected by TRIP and TWIP effects. - Highlights: •The resistances to HCF of various high-Mn steels were measured. •The variables affecting tensile and HCF behaviors of high-Mn steels were assessed. •The relationship between tensile and the HCF behaviors of high-Mn steels was established.

36 MATERIALS SCIENCE↗

The compressive deformation mechanisms of a coarse-grained AgInCd alloy

Highlights: • The compressive deformation mechanisms of a coarse-grained AgInCd alloy are investigated. • The deformation mechanisms are full dislocation slip and multiplication when strain is small. • Dominant deformation mechanisms convert into deformation twinning when strain reaches 50%. • Dislocation densities and twin thicknesses reduce in twinned grains with strain increasing. - Abstract: The compressive deformation mechanisms of a coarse-grained AgInCd alloy have been investigated in the present study. When compressive strain is not higher than 30%, the deformation mechanisms transform from full dislocation slip and multiplication into the two coefficient mechanisms of full dislocation slip and partial dislocation emission with increasing compressive strain. When compressive strain reaches 50%, the dominant deformation mechanisms convert into deformation twinning. With further increasing strain, the dislocation densities decrease and the twin thicknesses reduce in the nano-twinned grains. Twin boundary possesses a weaker strengthening effect comparing with grain boundary for the AgInCd alloys.

36 MATERIALS SCIENCE↗

Measuring Three-Dimensional Strain and Structural Defects in a Single InGaAs Nanowire Using Coherent X-ray Multiangle Bragg Projection Ptychography

III - As nanowires are candidates for near-infrared light emitters and detectors that can be directly integrated onto silicon. However, nanoscale to microscale variations in structure, composition, and strain within a given nanowire, as well as variations between nanowires, pose challenges to correlating microstructure with device performance. In this work, we utilize coherent nanofocused X-rays to characterize stacking defects and strain in a single InGaAs nanowire supported on Si. By reconstructing diffraction patterns from the 2110 Bragg peak, we show that the lattice orientation varies along the length of the wire, while the strain field along the cross-section is largely unaffected, leaving the band structure unperturbed. Diffraction patterns from the 0110 Bragg peak are reproducibly reconstructed to create three-dimensional images of stacking defects and associated lattice strains, revealing sharp planar boundaries between different crystal phases of wurtzite (WZ) structure that contribute to charge carrier scattering. Phase retrieval is made possible by developing multiangle Bragg projection ptychography (maBPP) to accommodate coherent nanodiffraction patterns measured at arbitrary overlapping positions at multiple angles about a Bragg peak, eliminating the need for scan registration at different angles. The penetrating nature of X-ray radiation, together with the relaxed constraints of maBPP, will enable the in operando imaging of nanowire devices.

36 MATERIALS SCIENCE↗

X-ray diffraction of metastable structures from supercooled liquid hydrogen

We report time resolved observations of the crystallization from liquid hydrogen, supercooled to temperatures below the melting point, using 11.2 keV X-ray diffraction from the Linac Coherent Light Source (LCLS). Changes to the metastable solid and liquid structure factors have been dynamically measured. This allows for a direct determination of the lowest energy crystal polymorphs, the stacking probabilities, as well as the liquid and solid densities and temperatures. Such measurements provide experimental evidence of an Arrhenius-like growth kinetics along the stacking direction during supercooling.

36 MATERIALS SCIENCE↗

The 3C-6H polytypic transition in SiC as revealed by diffuse x-ray scattering

The 3C-6H polytypic transition in SiC single crystals is studied by means of diffuse x-ray scattering. Based on numerical simulations of the diffuse scattering intensity distribution we unambiguously prove that the 3C-6H transition in SiC occurs through the glide of partial dislocations and not by the ''layer displacement'' mechanism (i.e., local diffusional rearrangement of the Si and C atoms). The technique is extremely sensitive and can be used as a nondestructive mean to obtain statistically relevant values of the transition level down to {approx}0.05%.

36 MATERIALS SCIENCE↗

Internal quantum efficiency of III-nitride quantum dot superlattices grown by plasma-assisted molecular-beam epitaxy

We present a study of the optical properties of GaN/AlN and InGaN/GaN quantum dot (QD) superlattices grown via plasma-assisted molecular-beam epitaxy, as compared to their quantum well (QW) counterparts. The three-dimensional/two-dimensional nature of the structures has been verified using atomic force microscopy and transmission electron microscopy. The QD superlattices present higher internal quantum efficiency as compared to the respective QWs as a result of the three-dimensional carrier localization in the islands. In the QW samples, photoluminescence (PL) measurements point out a certain degree of carrier localization due to structural defects or thickness fluctuations, which is more pronounced in InGaN/GaN QWs due to alloy inhomogeneity. In the case of the QD stacks, carrier localization on potential fluctuations with a spatial extension smaller than the QD size is observed only for the InGaN QD-sample with the highest In content (peak emission around 2.76 eV). These results confirm the efficiency of the QD three-dimensional confinement in circumventing the potential fluctuations related to structural defects or alloy inhomogeneity. PL excitation measurements demonstrate efficient carrier transfer from the wetting layer to the QDs in the GaN/AlN system, even for low QD densities ({approx}10{sup 10} cm{sup -3}). In the case of InGaN/GaN QDs, transport losses in the GaN barriers cannot be discarded, but an upper limit to these losses of 15% is deduced from PL measurements as a function of the excitation wavelength.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Folding and stacking defects of graphene flakes probed by electron nanobeam

Combining nanoscale imaging with local electron spectroscopy and diffraction has provided direct information on folding and stacking defects of graphene flakes produced by unrolled multi-walled carbon nanotubes. Structural data obtained by nanoarea electron diffraction complemented with systematic electron energy loss spectroscopy measurements of the surface plasmon losses of single flakes show the presence of flat bilayer regions coexisting with folded areas where the topology of buckled graphene resembles that of warped carbon nanostructures.

36 MATERIALS SCIENCE↗

Amorphous silicon carbide passivating layers for crystalline-silicon-based heterojunction solar cells

Amorphous silicon enables the fabrication of very high-efficiency crystalline-silicon-based solar cells due to its combination of excellent passivation of the crystalline silicon surface and permeability to electrical charges. Yet, amongst other limitations, the passivation it provides degrades upon high-temperature processes, limiting possible post-deposition fabrication possibilities (e.g., forcing the use of low-temperature silver pastes). We investigate the potential use of intrinsic amorphous silicon carbide passivating layers to sidestep this issue. The passivation obtained using device-relevant stacks of intrinsic amorphous silicon carbide with various carbon contents and doped amorphous silicon are evaluated, and their stability upon annealing assessed, amorphous silicon carbide being shown to surpass amorphous silicon for temperatures above 300 °C. We demonstrate open-circuit voltage values over 700 mV for complete cells, and an improved temperature stability for the open-circuit voltage. Transport of electrons and holes across the hetero-interface is studied with complete cells having amorphous silicon carbide either on the hole-extracting side or on the electron-extracting side, and a better transport of holes than of electrons is shown. Also, due to slightly improved transparency, complete solar cells using an amorphous silicon carbide passivation layer on the hole-collecting side are demonstrated to show slightly better performances even prior to annealing than obtained with a standard amorphous silicon layer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Measurements and simulations of the optical gain and anti-reflection coating modal reflectivity in quantum cascade lasers with multiple active region stacks

We report spectrally resolved gain measurements and simulations for quantum cascade lasers (QCLs) composed of multiple heterogeneous stacks designed for broadband emission in the mid-infrared. The measurement method is first demonstrated on a reference single active region QCL based on a double-phonon resonance design emitting at 7.8 μm. It is then extended to a three-stack active region based on bound-to-continuum designs with a broadband emission range from 7.5 to 10.5 μm. A tight agreement is found with simulations based on a density matrix model. The latter implements exhaustive microscopic scattering and dephasing sources with virtually no fitting parameters. The quantitative agreement is furthermore assessed by measuring gain coefficients obtained by studying the threshold current dependence with the cavity length. These results are particularly relevant to understand fundamental gain mechanisms in complex semiconductor heterostructure QCLs and to move towards efficient gain engineering. Finally, the method is extended to the measurement of the modal reflectivity of an anti-reflection coating deposited on the front facet of the broadband QCL.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of atomic-arrangement matching on La{sub 2}O{sub 3}/Ge heterostructures for epitaxial high-k-gate-stacks

We demonstrate a high-quality La{sub 2}O{sub 3} layer on germanium (Ge) as an epitaxial high-k-gate-insulator, where there is an atomic-arrangement matching condition between La{sub 2}O{sub 3}(001) and Ge(111). Structural analyses reveal that (001)-oriented La{sub 2}O{sub 3} layers were grown epitaxially only when we used Ge(111) despite low growth temperatures less than 300 °C. The permittivity (k) of the La{sub 2}O{sub 3} layer is roughly estimated to be ∼19 from capacitance-voltage (C-V) analyses in Au/La{sub 2}O{sub 3}/Ge structures after post-metallization-annealing treatments, although the C-V curve indicates the presence of carrier traps near the interface. By using X-ray photoelectron spectroscopy analyses, we find that only Ge–O–La bonds are formed at the interface, and the thickness of the equivalent interfacial Ge oxide layer is much smaller than that of GeO{sub 2} monolayer. We discuss a model of the interfacial structure between La{sub 2}O{sub 3} and Ge(111) and comment on the C-V characteristics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of stacking order on device performance of bilayer black phosphorene-field-effect transistor

We investigate the effect of stacking order of bilayer black phosphorene on the device properties of p-MOSFET and n-MOSFET. Two layers of black phosphorus are stacked in three different orders and are used as channel material in both n-MOSFET and p-MOSFET devices. The effects of different stacking orders on electron and hole effective masses and output characteristics of MOSFETs, such as ON currents, ON/OFF ratio, and transconductance are analyzed. Our results show that about 1.37 times and 1.49 times increase in ON current is possible along armchair and zigzag directions, respectively, 55.11% variation in transconductance is possible along armchair direction, by changing stacking orders (AA, AB, and AC) and about 8 times increase in ON current is achievable by changing channel orientation (armchair or zigzag) in p-MOSFET. About 14.8 mV/V drain induced barrier lowering is observed for both p-MOSFET and n-MOSFET, which signifies good immunity to short channel effects.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Role of structural defects in the ultraviolet luminescence of multiwall boron nitride nanotubes

BN nanotubes (BNNTs) are structurally similar to their carbon counterparts, though much less investigated. New synthesis methods have been recently reported, enabling the production of industrial quantities and stimulating the search of new applications for the BNNTs. In this paper, we investigate the luminescence of multiwall BNNTs. By performing cathodoluminescence experiments on single tubes at 10 K, we show that the tube luminescence is highly heterogeneous (i) from tube to tube and (ii) spatially along a single tube. By combining cathodoluminescence measurements with a nanometer excitation and transmission electron microscopy on the same tube, we correlate luminescence and structural features. We conclude that the near-band-edge luminescence of BNNTs (≈5.4 eV) is related to the presence of extended structural defects, such as dislocations or ruptures in the wall stacking.

36 MATERIALS SCIENCE↗

Microstructural evolution of nanotwinned Al-Zr alloy with significant 9R phase

Aluminum (Al) alloys have a multitude of applications, notably in the automotive, aerospace and coating industries, yet they exhibit significantly lower mechanical strength than conventional steels. Nanotwins drastically improve mechanical strength while retaining ductility. However, the high SFE of Al largely prevents twinning. Here, we synthesize Al-Zr alloy films containing an abundance of incoherent twin boundaries and 9R phases. These alloys exhibit an extended solid solubility of Zr, retaining a columnar nanotwinned structure across all compositions. These films reach a hardness up to 4.2 GPa with 10 at% Zr and demonstrate the capacity for producing strong Al alloys with nanotwins.

36 MATERIALS SCIENCE↗

Nucleation of Dislocations in 3.9 nm Nanocrystals at High Pressure

As circuitry approaches single nanometer length scales, it has become important to predict the stability of single nanometer-sized metals. The behavior of metals at larger scales can be predicted based on the behavior of dislocations, but it is unclear if dislocations can form and be sustained at single nanometer dimensions. Here, we report the formation of dislocations within individual 3.9 nm Au nanocrystals under nonhydrostatic pressure in a diamond anvil cell. We used a combination of x-ray diffraction, optical absorbance spectroscopy, and molecular dynamics simulation to characterize the defects that are formed, which were found to be surface-nucleated partial dislocations. These results indicate that dislocations are still active at single nanometer length scales and can lead to permanent plasticity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Stacking Domain Wall Magnons in Twisted van der Waals Magnets

In this report using bilayer CrI 3 as an example, we demonstrate that stacking domain walls in van der Waals magnets can host one-dimensional (1D) magnon channels, which have lower energies than bulk magnons. Interestingly, some magnon channels are hidden in magnetically homogeneous background and can only be inferred with the knowledge of stacking domain walls. Compared to 1D magnons confined in magnetic domain walls, 1D magnons in stacking domain walls are more stable against external perturbations. We show that the relaxed moiré superlattices of small-angle twisted bilayer CrI 3 is a natural realization of stacking domain walls and host interconnected moiré magnon network. Our Letter reveals the importance of stacking domain walls in understanding magnetic properties of van der Waals magnets and extends the scope of stacking engineering to magnetic dynamics.

2-dimensional system↗