Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILICONES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Thick film silicon growth techniques

One inch wide silicon ribbons up to 14 inches long have been produced from graphite dies. Several different techniques have been employed to improve the semiconductor purity of silicon. This has resulted in a general increase in quality although the techniques involved have not been optimized. The power factor of uncoated ribbon solar cells produced for material evaluation has increased to approximately 75% of those evaluation cells made from commercial silicon. The present limitation is believed due to low lifetime. Additional work has continued with new die materials; however, only composite dies of SiO2 and C show significant potential at this time.

Bates, H. E.↗
NASA NTRS1975

Low-Cost thin-layer silicon solar cells

Two methods have been found to lower cost of polycrystalline silicon solar cells. Successive layers of polycrystalline silicon are deposited over supporting substrates of relatively inexpensive metallurgical-grade polycrystalline silicon, graphite, or steel.

Chu, T. L.↗
NASA NTRS1975

Adhesion and friction behavior of group 4 elements germanium, silicon, tin, and lead

Adhesion and friction studies were conducted with thin films of the group IV elements silicon, germanium, tin, and lead ion plated on the nickel (011) substrate. The mating surface was gold (111). Contacts were made for the elements in the clean state and with oxygen present. Adhesion and friction experiments were conducted at very light loads of 1 to 10 g. Sliding was at a speed of 0.7 mm/min. Friction results indicate that the more covalently bonded elements silicon and germanium exhibit lower adhesion and friction than the more metallic bonded tin and lead. The adhesion of gold to germanium was observed, and recrystallization of the transferred gold occurred. Plastic flow of germanium was seen with sliding. Oxygen reduced, but did not eliminate, the adhesion observed with germanium and silicon.

Buckley, D. H.↗
NASA NTRS1975

Dependence of resistivity on the doping level of polycrystalline silicon

The electrical resistivity of polycrystalline silicon films has been studied as a function of doping concentration and heat treatment. The films were grown by the chemical vapor decomposition of silane on oxidized silicon wafers. The resistivity of the as-deposited films was widely scattered but independent of dopant atom concentration at the lightly doped levels and was strong function of dopant level in the more heavily doped regions. Postdeposition heat treatments in an oxidizing atmosphere remove scatter in the data. The resultant resistivity for dopant levels less than 10 to the 16th atoms/per cu cm was approximately equal to that of intrinsic silicon. In the next 2 orders of magnitude increase in dopant level, the resistivity dropped 6 orders of magnitude. A model, based on high dopant atom segregation in the grain boundaries, is proposed to explain the results.

Fripp, A. L.↗
NASA NTRS1975

An investigation of RF sputter etched silicon surfaces using helium ion backscatter

The effect of RF sputter etching on the (111) surface of silicon was studied by observing backscatter spectra from a 2 MeV, He-4(+) beam oriented along the silicon 111 orientation channel. Silicon samples were RF sputter etched in an argon discharge at electrode bias potentials ranging from 0.5 to 2.5 kV. The samples were sputter etched for a time sufficient for the lattice damage to reach saturation. Analysis of these samples revealed that the thickness of this damage layer and the concentration of trapped argon increased with electrode bias potential. An annealing study of these damaged surfaces was carried out to 900 C.

Sachse, G. W.↗
NASA NTRS1975

Low cost processes for solar-grade silicon

Upgrading metallurgical grade silicon is being pursued in four associated areas in order to improve the purity of the normally 98% material. The first two work areas involve purification of raw materials entering the process in addition to upgrading the arc furnace itself. The second two areas of process upgrading comprise improving the purity of the silicon after it leaves the arc furnace by reactive gas blowing and unidirectional freezing. The best cell produced to date was fabricated from MG-Si that had been blown with an O2-Cl2 mixture, unidirectionally solidified, and 6-float-zone passed (to determine a base boron level of 0.04 ohm/cm). The cell showed a 10.7% AMO efficiency. In the other processes category, the use of silicates as a silicon source and of electrolysis as a process were studied. The best electrolytic process uses a 1000 C fused salt of silica in cryolite.

Hunt, L. P.↗
NASA NTRS1975

Silicon crystal as a low work function collector

A test vehicle with a low work function collector which can be incorporated in a thermionic converter was constructed from standard vacuum components including an ultrahigh vacuum ion pump. The collector assembly was fabricated by diffusion bonding a (100) oriented silicon single crystal to a molybdenum block. The silicon surface was treated with cesium and oxygen to produce an NEA-type condition and the results were tested by photoemission and work function measurements. An n-type silicon collector was successfully activated to a work function of 1.0 eV, which was verified by photoemission spectral yield measurements. The stability test of an activated surface at elevated temperatures was conducted in the range from room temperature to 619 K, which was slightly lower than the designed collector temperature of 700 K. The work function measurements clearly demonstrated that the behavior of cesium replenishment on the activated Si surface was similar in nature to that of a metallic surface; that is, the loss of cesium by thermal desorption could be compensated by maintaining an adequate vapor pressure of cesium.

Chang, K. H.↗
NASA NTRS1976

Development of a high efficiency thin silicon solar cell

One hundred thin (120 microns to 260 microns) silicon-aluminum solar cells were fabricated and tested. Silicon slices were prepared, into which an aluminum alloy was evaporated over a range of temperatures and times. Antireflection coatings of tantalum oxide were applied to the cells. Reflectance of the silicon-aluminum interfaces was correlated to alloy temperature (graphs are shown). Optical measurements of the rear surface-internal reflectance of the cells were performed using a Beckman spectrophotometer. An improved gridline pattern was evaluated and stability tests (thermal cycling tests) were performed. Results show that: (1) a high-index, high-transmittance antireflection coating was obtained; (2) the improved metallization of the cells gave a 60 percent rear surface-internal reflectance, and the cells displayed excellent fill factors and blue response of the spectrum; (3) an improved gridline pattern (5 micron linewidths compared to 13 micron linewidths) resulted in a 1.3 percent improvement in short circuit currents; and (4) the stability tests showed no change in cell properties.

Lindmayer, J.↗
NASA NTRS1976

Silicon materials task of the low cost solar array project, part 2

Purity requirements for solar cell grade silicon material was developed and defined by evaluating the effects of specific impurities and impurity levels on the performance of silicon solar cells. Also, data was generated forming the basis for cost-tradeoff analyses of silicon solar cell material. Growth, evaluation, solar cell fabrication and testing was completed for the baseline boron-doped Czochralski material. Measurements indicate Cn and Mn seriously degrade cell performance, while neither Ni nor Cu produce any serious reduction in cell efficiency.

Hopkins, R. H.↗
NASA NTRS1975

Demonstration of the feasibility of automated silicon solar cell fabrication

A study effort was undertaken to determine the process, steps and design requirements of an automated silicon solar cell production facility. Identification of the key process steps was made and a laboratory model was conceptually designed to demonstrate the feasibility of automating the silicon solar cell fabrication process. A detailed laboratory model was designed to demonstrate those functions most critical to the question of solar cell fabrication process automating feasibility. The study and conceptual design have established the technical feasibility of automating the solar cell manufacturing process to produce low cost solar cells with improved performance. Estimates predict an automated process throughput of 21,973 kilograms of silicon a year on a three shift 49-week basis, producing 4,747,000 hexagonal cells (38mm/side), a total of 3,373 kilowatts at an estimated manufacturing cost of $0.866 per cell or $1.22 per watt.

Taylor, W. E.↗
NASA NTRS1976

Low work function silicon collector for thermionic converters

To improve the efficiency of present thermionic converters, single crystal silicon was investigated as a low work function collector material. The experiments were conducted in a test vehicle which resembled an actual thermionic converter. Work function as low as 1.0eV was obtained with an n-type silicon. The stabilities of the activated surfaces at elevated temperatures were tested by raising the collector temperature up to 829 K. By increasing the Cs arrival rate, it was possible to restore the originally activated low work function of the surface at elevated surface temperatures. These results, plotted in the form of Rasor-Warner curve, show a behavior similar to that of metal electrode except that the minimum work function was much lower with silicon than with metals.

Chang, K. H.↗
NASA NTRS1975

Dendritic web - A viable material for silicon solar cells

The dendritic web process is a technique for growing thin silicon ribbon from liquid silicon. The material is suitable for solar cell fabrication and, in fact, cells fabricated on web material are equivalent in performance to cells fabricated on Czochralski-grown material. A recently concluded study has delineated the thermal requirements for silicon web crucibles, and a detailed conceptual design has been developed for a laboratory growth apparatus.

Seidensticker, R. G.↗
NASA NTRS1976

The effects of incomplete annealing on the temperature dependence of sheet resistance and gage factor in aluminum and phosphorus implanted silicon on sapphire

Partial annealing of damage to the crystal lattice during ion implantation reduces the temperature coefficient of resistivity of ion-implanted silicon, while facilitating controlled doping. Reliance on this method for temperature compensation of the resistivity and strain-gage factor is discussed. Implantation conditions and annealing conditions are detailed. The gage factor and its temperature variation are not drastically affected by crystal damage for some crystal orientations. A model is proposed to account for the effects of electron damage on the temperature dependence of resistivity and on silicon piezoresistance. The results are applicable to the design of silicon-on-sapphire strain gages with high gage factors.

Pisciotta, B. P.↗
NASA NTRS1977

Solar meter with silicon photocell

Instrument for measuring light falling on given spot uses simple silicon photovoltaic cell as sensing element. It measures all light at location: direct, scattered, reflected, or reradiated. Silicon cell is coated with thick antireflecting layer of silicon monoxide and is enclosed in glass dome. Large heat sink reduces temperature fluctuations. Instrument is accurate within few percentage points over angle of Sun's arc across sky.

Yanow, G.↗
NASA NTRS1976

LSSA (Low-cost Silicon Solar Array) project

Methods are explored for economically generating electrical power to meet future requirements. The Low-Cost Silicon Solar Array Project (LSSA) was established to reduce the price of solar arrays by improving manufacturing technology, adapting mass production techniques, and promoting user acceptance. The new manufacturing technology includes the consideration of new silicon refinement processes, silicon sheet growth techniques, encapsulants, and automated assembly production being developed under contract by industries and universities.

Source record↗
NASA NTRS1976

Ablative performance of uncoated silicone-modified and shuttle baseline reinforced carbon composites

The relative ablative performance of uncoated silicone-modified reinforced carbon composite (RCC) and uncoated shuttle baseline RCC substrates was investigated. The test specimens were 13 plies (5.3 to 5.8 millimeters) thick and had a 25-millimeter-diameter test face. Prior to arc tunnel testing, all specimens were subjected to a heat treatment simulating the RCC coating process. During arc tunnel testing, the specimens were exposed to cold wall heating rates of 178 to 529 kilowatts/sq m and stagnation pressures ranging from 0.015 to 0.046 atmosphere at Mach 4.6 in air, with and without preheating in nitrogen. The results show that the ablative performance of uncoated silicone-modified RCC substrates is significantly superior to that of uncoated shuttle baseline RCC substrates over the range of heating conditions used. These results indicate that the silicone-modified RCC substrate would yield a substantially greater safety margin in the event of complete coating loss on the shuttle orbiter.

Dicus, D. L.↗
NASA NTRS1977

Thick-film materials for silicon photovoltaic cell manufacture

Thick film technology is applicable to three areas of silicon solar cell fabrication; metallization, junction formation, and coating for protection of screened ohmic contacts, particularly wrap around contacts, interconnection and environmental protection. Both material and process parameters were investigated. Printed ohmic contacts on n- and p-type silicon are very sensitive to the processing parameters of firing time, temperature, and atmosphere. Wrap around contacts are easily achieved by first printing and firing a dielectric over the edge and subsequently applying a low firing temperature conductor. Interconnection of cells into arrays can be achieved by printing and cofiring thick film metal pastes, soldering, or with heat curing conductive epoxies on low cost substrates. Printed (thick) film vitreous protection coatings do not yet offer sufficient optical uniformity and transparency for use on silicon. A sprayed, heat curable SiO2 based resin shows promise of providing both optical matching and environmental protection.

Field, M. B.↗
NASA NTRS1977

Solar breeder: Energy payback time for silicon photovoltaic systems

The energy expenditures of the prevailing manufacturing technology of terrestrial photovoltaic cells and panels were evaluated, including silicon reduction, silicon refinement, crystal growth, cell processing and panel building. Energy expenditures include direct energy, indirect energy, and energy in the form of equipment and overhead expenses. Payback times were development using a conventional solar cell as a test vehicle which allows for the comparison of its energy generating capability with the energies expended during the production process. It was found that the energy payback time for a typical solar panel produced by the prevailing technology is 6.4 years. Furthermore, this value drops to 3.8 years under more favorable conditions. Moreover, since the major energy use reductions in terrestrial manufacturing have occurred in cell processing, this payback time directly illustrates the areas where major future energy reductions can be made -- silicon refinement, crystal growth, and panel building.

Lindmayer, J.↗