Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RECEIVER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Calibration of the receiver channel for the GOPEX precursor experiments

Calibration measurements for the cooled (253 K) photomultiplier tube (PMT) detector, used on the receiver channel of the transmit/receive (T/R) switch for GOPEX, were conducted in the laboratory. A pulsed frequency-doubled neodymium:yttrium-aluminum-garnet (Nd:YAG) laser was used to direct 532-mn light on the PMT. By monitoring the energy per pulse of the light incident on the PMT, the minimum number of photons detected could be determined. These results agreed with the photon flux back-calculated from the PMT output waveform. Approximately 700 incident photons arriving during a temporal pulse width of approximately 65 nsec were detected with a signal-to-noise ratio (SNR) of approximately 1. Other receiver channel characteristics, such as PMT dark currents, optical transmission, and interference filter sensitivity to angle of light incidence, were also measured.

Biswas, A.↗

Streak camera based SLR receiver for two color atmospheric measurements

To realize accurate two-color differential measurements, an image digitizing system with variable spatial resolution was designed, built, and integrated to a photon-counting picosecond streak camera, yielding a temporal scan resolution better than 300 femtosecond/pixel. The streak camera is configured to operate with 3 spatial channels; two of these support green (532 nm) and uv (355 nm) while the third accommodates reference pulses (764 nm) for real-time calibration. Critical parameters affecting differential timing accuracy such as pulse width and shape, number of received photons, streak camera/imaging system nonlinearities, dynamic range, and noise characteristics were investigated to optimize the system for accurate differential delay measurements. The streak camera output image consists of three image fields, each field is 1024 pixels along the time axis and 16 pixels across the spatial axis. Each of the image fields may be independently positioned across the spatial axis. Two of the image fields are used for the two wavelengths used in the experiment; the third window measures the temporal separation of a pair of diode laser pulses which verify the streak camera sweep speed for each data frame. The sum of the 16 pixel intensities across each of the 1024 temporal positions for the three data windows is used to extract the three waveforms. The waveform data is processed using an iterative three-point running average filter (10 to 30 iterations are used) to remove high-frequency structure. The pulse pair separations are determined using the half-max and centroid type analysis. Rigorous experimental verification has demonstrated that this simplified process provides the best measurement accuracy. To calibrate the receiver system sweep, two laser pulses with precisely known temporal separation are scanned along the full length of the sweep axis. The experimental measurements are then modeled using polynomial regression to obtain a best fit to the data. Data aggregation using normal point approach has provided accurate data fitting techniques and is found to be much more convenient than using the full rate single shot data. The systematic errors from this model have been found to be less than 3 ps for normal points.

Varghese, Thomas K.↗

Digital receiver for on-board FM/FSK-FM/BPSK demodulation

An all-digital demodulator FM/FSK-FM/BPSK is presented. The proposed architecture allows the 1-bit IF down-sampling technique with the hardware simplification of receiver analog section. The receiver exhibits great flexibility both in terms of signal demodulation (FSK or BPSK, subcarrier/ tone frequency, data rate) and interface capability. The demodulator is going to be realized in a VLSI chip (20 Kgate complexity). This paper describes the demodulator structure and its demodulation performances obtained with a breadboard based on programmable logic devices. The choice of a simple and effective scheme for frequency detection (FM and FSK demodulators) is suggested by system design considerations as well. Signal processing algorithms include also a Costas carrier phase recovery scheme in the case of BPSK signal and data transition tracking loop for the bit clock recovery. Test results address this solution as one of the most suitable for TT&C space application.

Boscagli, G.↗

New approaches for tracking earth orbiters using modified GPS ground receivers

A Global Positioning System (GPS) flight receiver provides a means to precisely determine orbits for satellites in low to moderate altitude orbits. Above a 5000-km altitude, however, relatively few GPS satellites are visible. New approaches to orbit determination for satellites at higher altitudes could reduce DSN antenna time needed to provide navigation and orbit determination support to future missions. Modification of GPS ground receivers enables a beacon from the orbiter to be tracked simultaneously with GPS data. The orbit accuracy expected from this GPS-like tracking (GLT) technique is expected to be in the range of a few meters or better for altitudes up to 100,000 km with a global ground network. For geosynchronous satellites, however, there are unique challenges due to geometrical limitations and to the lack of strong dynamical signature in tracking data. We examine two approaches for tracking the Tracking and Data Relay Satellite System (TDRSS) geostationary orbiters. One uses GLT with a global network; the other relies on a small 'connected element' ground network with a distributed clock for short-baseline differential carrier phase (SB Delta Phi). We describe an experiment planned for late 1993, which will combine aspects of both GLT and SB Delta Phi, to demonstrate a new approach for tracking the Tracking and Data Relay Satellites (TDRSs) that offers a number of operationally convenient and attractive features. The TDRS demonstration will be in effect a proof-of-concept experiment for a new approach to tracking spacecraft which could be applied more generally to deep-space as well as near-Earth regimes.

Lichten, S. M.↗

Performance and durability of high emittance heat receiver surfaces for solar dynamic power systems

Haynes 188, a cobalt-based superalloy, will be used to make thermal energy storage (TES) containment canisters for a 2 kW solar dynamic ground test demonstrator (SD GTD). Haynes 188 containment canisters with a high thermal emittance (epsilon) are desired for radiating heat away from local hot spots, improving the heating distribution, which will in turn improve canister service life. In addition to needing a high emittance, the surface needs to be durable in an elevated temperature, high vacuum environment for an extended time period. Thirty-five Haynes 188 samples were exposed to 14 different types of surface modification techniques for emittance and vacuum heat treatment (VHT) durability enhancement evaluation. Optical properties were obtained for the modified surfaces. Emittance enhanced samples were exposed to VHT for up to 2692 hours at 827 C and less than or equal to 10(exp -6) torr with integral thermal cycling. Optical properties were taken intermittently during exposure, and after final VHT exposure. The various surface modification treatments increased the emittance of pristine Haynes 188 from 0.11 up to 0.86. Seven different surface modification techniques were found to provide surfaces which met the SD GTD receiver VHT durability requirement. Of the 7 surface treatments, 2 were found to display excellent VHT durability: an alumina based (AB) coating and a zirconia based coating. The alumina based coating was chosen for the epsilon enhancement surface modification technique for the SD GTD receiver. Details of the performance and vacuum heat treatment durability of this coating and other Haynes 188 emittance surface modification techniques are discussed. Technology from this program will lead to successful demonstration of solar dynamic power for space applications, and has potential for application in other systems requiring high emittance surfaces.

Degroh, Kim K.↗

Design and implementation of a hybrid digital phase-locked loop with a TMS320C25: An application to a transponder receiver breadboard

Design, modeling, analysis, and simulation of a phase-locked loop (PLL) with a digital loop filter are presented in this article. A TMS320C25 digital signal processor (DSP) is used to implement this digital loop filter. In order to keep the compatibility, the main design goal was to replace the analog PLL (APLL) of the Deep-Space Transponder (DST) receiver breadboard's loop filter with a digital loop filter without changing anything else. This replacement results in a hybrid digital PLL (HDPLL). Both the original APLL and the designed HDPLL are Type I second-order systems. The real-time performance of the HDPLL and the receiver is provided and evaluated.

Yeh, H.-G.↗

A new high-sensitivity superconducting receiver for mm-wave remote-sensing spectroscopy of the stratosphere

We describe a recently constructed ground-based mm-wave spectrometer incorporating a superconducting tunnel junction as a heterodyne mixer-receiver. Under conditions of low tropospheric water vapor, the superior sensitivity of this receiver allows spectral line measurements of stratospheric molecules with mixing ratios as small as a few tenths of a part per billion (e.g., ClO, HCN) to be made in 4 to 6 hours, with a signal to noise ratio of at least 30:1. We expect to be able to halve this time by further improvement of the mixer's intrinsic noise level.

Dezafra, R. L.↗

High speed QPPM direct detection optical communication receivers for FSDD intersatellite links

This final report consists of four separate reports, one for each project involved in this contract. The first report is entitled '325 Mbps QPPM (quaternary pulse position modulation) Direct Detection Free Space Optical Communication Encoder and Receiver,' which was our primary work. The second report is entitled 'Test Results of the 325 Mbps QPPM High Speed Data Transmission GaAs ASICs,' which describes our work in connection with Galaxy Microsystems, Inc. who produced these ASICs for NASA. The third report, 'Receiver Performance Analysis of BPPM Optical Communication Systems Using 1.3 micron Wavelength Transmitter and InGaAs PIN Photodiodes,' was prepared at the request of the NASA/Photonics Branch for their efforts in upgrading the 1773 optical fiber data bus. The fourth report, 'Photomultiplier Tubes for Use at 1.064 micron Wavelength,' was also prepared at the request of the NASA/Photonics Branch as a research project.

Davidson, Frederic M.↗

A demonstration of TDRS orbit determination using differential tracking observables from GPS ground receivers

A Global Positioning System (GPS) flight receiver provides a means of precisely determining orbits for satellites in low to moderate altitude orbits. Above 5000 km altitude, however, relatively few GPS satellites are visible. We present a new approach to orbit determination for satellites at higher altitudes. Modification of GPS ground receivers enables a beacon from the orbiter to be tracked simultaneously with GPS data. The orbit accuracy expected from this GPS-like tracking (GLT) technique in principle could be comparable to accuracies of GPS orbits. Present-day GPS orbit quality from a daily semi-automated analysis system at the Jet Propulsion Laboratory is at the 30 - 50 cm level: expected accuracies for orbiters with GLT are calculated to be in the few-meter range for altitudes up to 100000 km. For geosynchronous satellites, however, there are unique challenges due to geometrical limitations and to the lack of strong dynamical signature in tracking data. We examine two approaches for tracking Tracking and Data Relay Satellites (TDRS) geostationary orbiters. One uses GLT with a global network; the other relies on a small `connected element' ground network with a distributed clock for short baseline differential carrier phase (SB Delta Phi). In priciple, both could meet 50-m TDRS operational requirements. However there are practical difficulties with either pure GLT or SB Delta Phi tracking schemes for present-day TDRS satellites. We describe an experiment planned for late 1993 which will combine aspects of both GLT and SB Delta Phi to demonstrate a new approach for tracking TDRS which offers a number of operationally convenient and attractive features. The TDRS demo will in effect ba a proof of concept experiment for both the GLT and SB Delta Phi approaches to tracking spacecraft.

Lichten, Stephen M.↗

Media Controller For Receiving Data From A TAXI(TM) Link

TAXI(TM) media controller (TMC) is interface circuit that supports operation of test equipment in diagnosis of telemetry system in which data communicated via TAXI(TM) links. TMC designed specifically for use with TAXI(TM) test adapter for monitoring and testing telemetry data signals generated by payloads and other subsystems of Space Station Freedom. Overall, TMC characterized as providing interface between output part of a TAXI(TM) receiving chip and input port of memory system in test adapter. TMC detects some abnormalities in received data stream and resynchronizes stream to locally generated clock signal.

Stauffer, David R.↗

Preliminary analysis of fluctuations in the received uplink-beacon-power data obtained from the GOLD experiments

Uplink data from recent free-space optical communication experiments carried out between the Table Mountain Facility and the Japanese Engineering Test Satellite are used to study fluctuations caused by beam propagation through the atmosphere. The influence of atmospheric scintillation, beam wander and jitter, and multiple uplink beams on the statistics of power received by the satellite is analyzed and compared to experimental data. Preliminary analysis indicates the received signal obeys an approximate lognormal distribution, as predicted by the weak-turbulence model, but further characterization of other sources of fluctuations is necessary for accurate link predictions.

M. Jeganathan↗

Submillimeter-Wave Receiver Containing An SIS Mixer

Submillimeter-wave heterodyne receiver designed to operate at input frequencies in range of 480 to 650 GHz. Intended for use in radio astronomy at frequency of 547 or 626 GHz. Heart of receiver is waveguide mixer that includes adjustable backshort and electric-field-plane tuner. Mixing element high-current-density superconductor/insulator/superconductor (SIS) tunnel junction integrated with superconductive microstrip radio-frequency circuit that tunes out capacitance of junction; matching complex impedance of junction to available tuning range of waveguide mount.

Febvre, Pascal↗

Satellite diversity and its implications on the RAKE receiver architecture for CDMA-based S-PCN's

In this paper we examine the applicability of RAKE receivers in a mobile LEO satellite channel and identify the potential problem areas. We then proceed to investigate the possibility of a coherent combining architecture (downlink) in the presence of satellite diversity. We closely examine the path delay difference statistics of a diversity channel and propose a delay compensation scheme for the downlink in order to reduce the complexity of the user terminal. Finally, the required modifications to the conventional RAKE receiver are proposed and discussed.

Taaghol, P.↗

How Bad Receiver Coordinates Can Affect GPS Timing

Many sources of error are possible when the Global Positioning System (GPS) is used for time comparisons. Some of these errors have been listed by Lewandowski. Because of the complexity of the system, an error source could have more than one effect. This paper will present theoretical and observational results by offsetting a receiver's coordinates. The calculations show how an error as small as three meters in any direction can result in a timing error of more than 10 nanoseconds. The GPS receiver must be surveyed to better than 0.2 meter accuracy for the timing error to be sub-nanosecond.

Chadsey, H.↗

Micromachined Millimeter- and Submillimeter-wave SIS Heterodyne Receivers for Remote Sensing

This is a progress report for the second year of a NASA-sponsored project. The report discusses the design and fabrication of micromachined Superconductor Insulator Superconductor (SIS) heterodyne receivers with integrated tuning elements. These receivers tune out the functional capacitance at desired frequencies, resulting in less noise, lower temperatures and broader bandwidths. The report also discusses the design and fabrication of the first monolithic 3x3 focal-plane arrays for a frequency range of 170-210 GHz. Also addressed is the construction of a 9-channel bias and read-out system, as well as the redesign of the IF connections to reduce cross talk between SIS junctions, which become significant a frequency of 1.5 GHz IF. Uniformity of the junction arrays were measured and antenna beam patterns of several array elements under operating conditions also were measured. Finally, video and heterodyne responses of our focal-plane arrays were measured as well. Attached is a paper on: 'Development of a 170-210 GHz 3x3 micromachined SIS imaging array'.

Hu, Qing↗

Submillimeter Spectroscopy with a 500-1000 GHz SIS Receiver

Sub-millimeter Spectroscopy with a 500-1000 GHz SIS Receiver, which extended over the period October 1, 1991 through January 31, 1997. The purpose of the grant was to fund the development and construction of a sensitive heterodyne receiver system for the submillimeter band (500-1000 GHz), using our newly-developed sensitive superconducting (SIS) detectors, and to carry out astronomical observations with this system aboard the NASA Kuiper Air- borne Observatory (a Lockheed C-141 aircraft carrying a 91 cm telescope). A secondary purpose of the grant was to stimulate the continued development of sensitive submillimeter detectors, in order to prepare for the next-generation airborne observatory, SOFIA, as well as future space missions (such as the ESA/NASA FIRST mission).

Zmuidzinas, J.↗

Preliminary Analysis of Fluctuations in the Received Uplink-Beacon-Power Data Obtained From the GOLD Experiments

Uplink data from recent free-space optical communication experiments carried out between the Table Mountain Facility and the Japanese Engineering Test Satellite are used to study fluctuations caused by beam propagation through the atmosphere. The influence of atmospheric scintillation, beam wander and jitter, and multiple uplink beams on the statistics of power received by the satellite is analyzed and compared to experimental data. Preliminary analysis indicates the received signal obeys an approximate lognormal distribution, as predicted by the weak-turbulence model, but further characterization of other sources of fluctuations is necessary for accurate link predictions.

Jeganathan, M.↗

Project Echo: Receiving System

A tracking horn-reflector antenna, a maser preamplifier (and standby parametric preamplifier), and a special FM demodulator were combined to form a low-noise receiving system which made possible the establishment of a high-quality voice circuit via the Echo I passive satellite. This paper describes the 2390-Mc receiving system located at the Bell Telephone Laboratories facility in Holmdel, New Jersey.

Ohm, E. A.↗