Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSURE DEPENDENCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Soot formation and temperature structure in small methane-oxygen diffusion flames at subcritical and supercritical pressures

An experimental study was conducted to examine the characteristics of laminar methane-oxygen diffusion flames up to 100 atmospheres. The influence of pressure on soot formation and on the structure of the temperature field was investigated over the pressure range of 10-90 atmospheres in a high-pressure combustion chamber using a non-intrusive, line-of-sight spectral soot emission diagnostic technique. Two distinct zones characterized the appearance of a methane and pure oxygen diffusion flame: an inner luminous zone similar to the methane-air diffusion flames, and an outer diffusion flame zone which is mostly blue. The flame height, marked by the visible soot radiation emission, was reduced by over 50% over the pressure range of 10-100 atmospheres. Between 10 and 40 atmospheres, the soot levels increased with increasing pressure; however, above 40 atmospheres the soot concentrations decreased with increasing pressure. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Pressurized chemical-looping combustion of coal with an iron ore-based oxygen carrier

Chemical-looping combustion (CLC) is a new combustion technology with inherent separation of CO{sub 2}. Most of the previous investigations on CLC of solid fuels were conducted under atmospheric pressure. A pressurized CLC combined cycle (PCLC-CC) system is proposed as a promising coal combustion technology with potential higher system efficiency, higher fuel conversion, and lower cost for CO{sub 2} sequestration. In this study pressurized CLC of coal with Companhia Valedo Rio Doce (CVRD) iron ore was investigated in a laboratory fixed bed reactor. CVRD iron ore particles were exposed alternately to reduction by 0.4 g of Chinese Xuzhou bituminous coal gasified with 87.2% steam/N{sub 2} mixture and oxidation with 5% O{sub 2} in N{sub 2} at 970 C. The operating pressure was varied between 0.1 MPa and 0.6 MPa. First, control experiments of steam coal gasification over quartz sand were performed. H{sub 2} and CO{sub 2} are the major components of the gasification products, and the operating pressure influences the gas composition. Higher concentrations of CO{sub 2} and lower fractions of CO, CH{sub 4}, and H{sub 2} during the reduction process with CVRD iron ore was achieved under higher pressures. The effects of pressure on the coal gasification rate in the presence of the oxygen carrier were different for pyrolysis and char gasification. The pressurized condition suppresses the initial coal pyrolysis process while it also enhances coal char gasification and reduction with iron ore in steam, and thus improves the overall reaction rate of CLC. The oxidation rates and variation of oxygen carrier conversion are higher at elevated pressures reflecting higher reduction level in the previous reduction period. Scanning electron microscope and energy-dispersive X-ray spectroscopy (SEM-EDX) analyses show that particles become porous after experiments but maintain structure and size after several cycles. Agglomeration was not observed in this study. An EDX analysis demonstrates that there is very little coal ash deposited on the oxygen carrier particles but no appreciable crystalline phases change as verified by X-ray diffraction (XRD) analysis. Overall, the limited pressurized CLC experiments carried out in the present work suggest that PCLC of coal is promising and further investigations are necessary. (author)

01 COAL, LIGNITE, AND PEAT↗

Effects of hydrogen preconversion on the homogeneous ignition of fuel-lean H{sub 2}/O{sub 2}/N{sub 2}/CO{sub 2} mixtures over platinum at moderate pressures

The impact of fractional hydrogen preconversion on the subsequent homogeneous ignition characteristics of fuel-lean (equivalence ratio {phi} = 0.30) H{sub 2}/O{sub 2}/N{sub 2}/CO{sub 2} mixtures over platinum was investigated experimentally and numerically at pressures of 1, 5 and 8 bar. Experiments were performed in an optically accessible channel-flow reactor and involved Raman measurements of major species over the catalyst boundary layer and planar laser induced fluorescence (LIF) of the OH radical. Simulations were carried out with a 2-D elliptic code that included detailed hetero-/homogeneous chemistry. The predictions reproduced the LIF-measured onset of homogeneous ignition and the Raman-measured transport-limited catalytic hydrogen consumption. For 0% preconversion and wall temperatures in the range 900 K {<=} T{sub w} {<=} 1100 K, homogeneous ignition was largely suppressed for p {>=} 5 bar due to the combined effects of intrinsic gas-phase hydrogen kinetics and the competition between the catalytic and gas-phase pathways for fuel consumption. A moderate increase of preconversion to 30% restored homogeneous combustion for p {>=} 5 bar, despite the fact that the water formed due to the upstream preconversion inhibited homogeneous ignition. The catalytically-produced water inhibited gas-phase combustion, particularly at higher pressures, and this kinetic inhibition was exacerbated by the diffusional imbalance of hydrogen that led to over-stoichiometric amounts of water in the near-wall hot ignitable regions. Radical adsorption/desorption reactions hindered the onset of homogeneous ignition and this effect was more pronounced at 1 bar. On the other hand, over the post-ignition reactor length, radical adsorption/desorption reactions significantly suppressed gas-phase combustion at 5 and 8 bar while their impact at 1 bar was weaker. By increasing hydrogen preconversion, the attained superadiabatic surface temperatures could be effectively suppressed. An inverse catalytically stabilized thermal combustion (CST) concept has been proposed, with gas-phase ignition achieved in an upstream porous burner via radiative and heat conduction feedback from a follow-up catalytic reactor. This arrangement moderated the superadiabatic surface temperatures and required modest or no preheat of the incoming mixture. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The role of energy transfer and competing bimolecular reactions in characterizing the unimolecular dissociations of allylic radicals

Resonantly stabilized radicals (RSR's) such as allylic radicals typically have bond energies exceeding 45 kcal/mol and are therefore reasonably long-lived up to quite high temperatures. Consequently, kinetics of the unimolecular dissociations and bimolecular reactions of these long-lived RSR's assume significance in high temperature chemically reacting systems such as in flames. Our recent analyses (J. Cho et al., Proc. Comb. Inst., 2022) of the uncertainty propagated by the energy transfer parameters for 1-methylallyl (1MA) dissociation to the laminar flame speed, indicates an intricate coupling between the kinetics of 1MA dissociation (chain propagation) and its reaction with H-atoms (chain-termination). Here, this work extends such analyses to other C 3 – C 5 allylic radicals: allyl, 2-methylallyl, 1,1-dimethylallyl, 1,2-dimethylallyl, and 1,3-dimethylallyl. Theoretical kinetics for the C 3 – C 4 allylic radicals were taken from prior literature studies (J.A. Miller et al., J. Phys. Chem., 2008; J. Cho et al., Proc. Comb. Inst., 2022; R.S. Tranter et al., Proc. Comb. Inst., 2017). Potential energy surfaces were newly computed for the dissociations of the larger C5 allylic radicals and the reactions of these radicals with H-atoms. These PES's were then used to calculate rate constants for the relevant unimolecular and bimolecular reactions. Energy transfer has a crucial role to play in these pressure-dependent reactions and therefore the present kinetics calculations relied on a-priori predictions of collisional energy transfer parameters to best characterize the branching between chain propagating unimolecular dissociations of these allylic radicals and chain terminating bimolecular reactions of these RSR's with H-atoms. Prompt dissociations are now established to be a universal feature of free radical dissociations. Here we have also characterized the propensity for prompt dissociations in these more-stable allylic RSR's and their role in combustion simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A comprehensive experimental and kinetic modeling study of di-isobutylene isomers: Part 2

A wide variety of high temperature experimental data obtained in this study complement the data on the oxidation of the two di-isobutylene isomers presented in Part I and offers a basis for an extensive validation of the kinetic model developed in this study. Due to the increasing importance of unimolecular decomposition reactions in high-temperature combustion, we have investigated the di-isobutylene isomers in high dilution utilizing a pyrolysis microflow reactor and detected radical intermediates and stable products using vacuum ultraviolet (VUV) synchrotron radiation and photoelectron photoion coincidence (PEPICO) spectroscopy. Additional speciation data at oxidative conditions were also recorded utilizing a plug flow reactor at atmospheric pressure in the temperature range 725-1150 K at equivalence ratios of 1.0 and 3.0 and at residence times of 0.35 s and 0.22 s, respectively. Combustion products were analyzed using gas chromatography (GC) and mass spectrometry (MS). Ignition delay time measurements for di-isobutylene were performed at pressures of 15 and 30 bar at equivalence ratios of 0.5, 1.0, and 2.0 diluted in 'air' in the temperature range 900-1400 K using a high-pressure shock-tube facility. New measurements of the laminar burning velocities of di-isobutylene/air flames are also presented. The experiments were performed using the heat flux method at atmospheric pressure and initial temperatures of 298-358 K. Moreover, data consistency was assessed with the help of analysis of the temperature and pressure dependencies of laminar burning velocity measurements, which was interpreted using an empirical power-law expression. Electronic structure calculations were performed to compute the energy barriers to the formation of many of the product species formed. The predictions of the present mechanism were found to be in adequate agreement with the wide variety of experimental measurements performed.

09 BIOMASS FUELS↗

A theoretical kinetic study of ĊH 3 + ṄH 2 : From electronic structure to NH 3 /CH 4 combustion modelling implications

Carbon–nitrogen interaction reactions play an important role in governing the reactivity of ammonia blended fuels. However, there remains uncertainties regarding their detailed reaction pathways and rate constants, hampering the development of high-fidelity chemical kinetic models. In this study, the kinetics of ĊH 3 + ṄH 2 , a key C–N interaction reaction in ammonia/methane blend combustion have been investigated. The potential energy surface has been explored using the high-level ANL0F method, yielding highly accurate stationary point energies that agree with ATcT values within 0.1 kcal mol –1 . Variable reaction coordinate transition state theory is used to treat the barrierless association and decomposition reaction channels, based on directly sampled radical-radical interaction energies at the CASPT2-F12(2e,2o)/cc-pVTZ-F12 level of theory. The minimum transitional mode numbers of states obtained are then coupled with the RRKM/master equation to calculate temperature- and pressure-dependent rate constants. Our a priori calculations capture available experimental measurements from the literature very well. The calculated rate constants have been incorporated into an NH 3 /CH 4 chemical kinetic model currently under development at the University of Galway. The effect of the updated kinetic data for ĊH 3 + ṄH 2 on model predicted NH 3 /CH 4 fuel reactivity is elucidated.

ab initio↗

A heuristic model inversion for coupled thermo-hydro-mechanical modelling of triaxial experiments

As multiphysics geomechanical models get developed, their increasing complexity and number of parameters make it particularly difficult to calibrate against experimental data. In this contribution, we present a heuristic workflow to invert for parameters of a coupled Thermo-Hydro-Mechanical (THM) model in a way that helps the theoretical modellers refine their definition of the underlying elasto-visco-plastic model itself. We apply this workflow to the calibration of deviatoric and volumetric data for two sets of triaxial experiments on mudstone and sandstone. Here, we show that beyond the calibration of well-defined parameters of the THM model, one or two scaling factors of the experimentally obtained yield surface and two more factors to capture the confinement and pore pressure dependency of the flow law lead to the satisfactory matching of series of experiments at varying confinements for two different rock types. Using this physical model, we also show that tracking the volumetric component of the mechanical power in the numerical simulations might allow reducing the number of experiments required to calibrate the model.

58 GEOSCIENCES↗

High-fidelity micro-scale modeling of the thermo-visco-plastic behavior of carbon fiber polymer matrix composites

An experimentally validated micro-scale analysis of the visco-thermo-mechanical behavior of polymer matrix composites under different loads is proposed. A new constitutive law for the matrix material is developed taking into account the pressure dependence of the material as well as strain-rate and temperature dependence. Capturing the matrix behavior under multi-axial stress states is concluded to be essential to accurately predict the composite material behavior, even when considering simple load cases such as transverse compression and/or shear. Without any calibration procedure at the composite level, good agreement with the experimental data is observed for different loading conditions, including strain-rate dependency. Using this validated micro-scale model, a three-dimensional simulation of the formation of a kink band under longitudinal compression of the composite is conducted. A new evidence at micro-scale is found supporting the hypothesis that shear stresses transferred between fibers and matrix are particularly important in the formation of the kink band.

36 MATERIALS SCIENCE↗

Effect of pressure and temperature on structural stability of potential hydrogen storage compound Li[subscript 3]AlH[subscript 6]

The crystal structure of Li{sub 3}AlH{sub 6} was investigated at high pressures upto 27 GPa using a diamond anvil cell with synchrotron radiation in addition to high temperature X-ray diffraction. Density functional theoretical (DFT) calculations were performed simultaneously. While the structure of Li{sub 3}AlH{sub 6} is stable on increasing temperature, the results of high pressure experiments show a pressure induced phase transition from the ambient R {bar 3} phase to a high pressure cubic Ia{bar 3} phase around 10.6 GPa. The transition pressure of 10.6 GPa and the bulk modulus value B{sub 0} = 32(2) GPa for the R{bar 3} phase obtained are in good agreement with the theoretical results.

08 HYDROGEN↗

Soot surface temperature measurements in pure and diluted flames at atmospheric and elevated pressures

Soot surface temperature was measured in laminar jet diffusion flames at atmospheric and elevated pressures. The soot surface temperature was measured in flames at one, two, four, and eight atmospheres with both pure and diluted (using helium, argon, nitrogen, or carbon dioxide individually) ethylene fuels with a calibrated two-color soot pyrometry technique. These two dimensional temperature profiles of the soot aid in the analysis and understanding of soot production, leading to possible methods for reducing soot emission. Each flame investigated was at its smoke point, i.e., at the fuel flow rate where the overall soot production and oxidation rates are equal. The smoke point was chosen because it was desirable to have similar soot loadings for each flame. A second set of measurements were also taken where the fuel flow rate was held constant to compare with earlier work. These measurements show that overall flame temperature decreases with increasing pressure, with increasing pressure the position of peak temperature shifts to the tip of the flame, and the temperatures measured were approximately 10% lower than those calculated assuming equilibrium and neglecting radiation. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of flow topology on the calculation of two-phase frictional multipliers in uniformly heated flow of R-134a in a rectangular duct

The two-phase frictional multipliers for SUVA R-134a flowing in a rectangular duct (with D{sub H} = 4.8 mm) have been measured for three nominal system pressures (0.88, 1.34 and 2.34 MPa) and four nominal mass fluxes (510, 1020 and 1740, 2040 kg/m{sup 2}/s) under uniform heat flux conditions. The data is compared with adiabatic data previously taken at similar flow conditions, as well as with several classical multiplier correlations. The comparisons reveal a strong effect of pressure and mass flux on the flow topology and, by extension, a large effect on the calculation of acceleration and frictional pressure drop components. For this fluid and this geometry, entrainment and fluid separation is enhanced at higher pressures and mass flux such that most of the liquid exists in the test section edges and as dispersed droplets in the core. For these cases, the classical simplified approach to calculate acceleration pressure drop fails to adequately predict the acceleration component and leads to erroneous calculations of frictional pressure drop from the measured total pressure drop. Best estimates of the true acceleration component are given, based on void profiles measured with a gamma densitometer system, comparisons to the adiabatic data, and recasting the data in terms of the total pressure drop multiplier as a function of the Martinelli parameter, X{sub tt}. (author)

42 ENGINEERING↗

Effects of operating pressure on flame oscillation and emission characteristics in a partially premixed swirl combustor

The influence of varying combustor pressure on flame oscillation and emission characteristics in the partially premixed turbulent flame were investigated. In order to investigate combustion characteristics in the partially premixed turbulent flame, the combustor pressure was controlled in the range of -30 to 30 kPa for each equivalence ratio ({phi} = 0.8-1.2). The r.m.s. of the pressure fluctuations increased with decreasing combustor pressure for the lean condition. The combustor pressure had a sizeable influence on combustion oscillation, whose dominant frequency varied with the combustor pressure. Combustion instabilities could be controlled by increasing the turbulent intensity of the unburned mixture under the lean condition. An unstable flame was caused by incomplete combustion; hence, EICO greatly increased. Furthermore, EINO{sub x} simply reduced with decreasing combustor pressure at a rate of 0.035 g/10 kPa. The possibility of combustion control on the combusting mode and exhaust gas emission was demonstrated. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The impacts of effective stress and CO 2 sorption on the matrix permeability of shale reservoir rocks [The impacts of CO 2 sorption and effective stress on the matrix permeability of shale reservoir rocks]

We assess the impacts of effective stress and CO 2 sorption on the bedding-parallel matrix permeability of the Utica shale through pressure pulse-decay experiments. We first measure permeability using argon at relatively high (14.6 MPa) and low (2.8 MPa) effective stresses to assess both pressure dependence and recoverability. We subsequently measure permeability using supercritical CO 2 and again using argon to assess changes due to CO 2 sorption. We find that injection of both argon and supercritical CO 2 reduces matrix permeability in distinct fashion. Samples with permeability higher than 10 –20 m 2 experience a large permeability reduction after treatment with argon, but a minor change after treatment with supercritical CO 2 . However, samples with permeability lower than this threshold undergo a slight change after treatment with argon, but a dramatic reduction after treatment with supercritical CO 2 . These results indicate that effective stress plays an important role in the evolution of relatively permeable facies, while CO 2 sorption dominates the change of ultra-low permeability facies. The permeability reduction due to CO 2 sorption varies inversely with initial permeability, which suggests that increased surface area from hydraulic stimulation with CO 2 may be counteracted by sorption effects in ultra-low permeability facies. As a result, we develop a conceptual model to explain how CO 2 sorption induces porosity reduction and volumetric expansion to constrict fluid flow pathways in shale reservoir rocks.

58 GEOSCIENCES↗

Reexamining supercritical gas adsorption theories in nano-porous shales under geological conditions

Adsorption is an important phenomenon in surface chemistry, especially for nano-porous shales. In the shale gas-in-place, adsorbed gas could contribute up to 85%. However, adsorption is hard to quantitatively characterize due to different adsorption mechanisms, patterns, surfaces, and pore sizes. Moreover, key thermodynamic parameters, such as the enthalpy of adsorption, are challenging to determine due to uncertainties in adsorbed gas densities used in constructing absolute isotherms. In this paper, we revisit the Brunauer, Emmett, and Teller (BET) model, analytically simplify Ono-Kondo (OK) models for subsurface shales, and compare commonly used mono- and multilayer adsorption models (e.g., Langmuir, supercritical Dubinin-Radushkevich (SDR), supercritical BET (SBET), and simplified OK (OKs) models) with recently proposed pressure-dependent adsorption densities to develop a practical and reliable methodology that can be used in the supercritical state, typical for subsurface black shale conditions.Three independent data sets were used for nitrogen and methane adsorption isotherms at different temperatures. Furthermore, we demonstrate that adsorption predicted by the SDR model is comparable or lower than that predicted by the SBET model, but higher than the amounts predicted by Langmuir and OK models. The nitrogen BET method tends to underestimate the accessible SSA for methane. Measurement of isosteric heat of adsorption is suggested instead of the experimental fitting method, due to the significant difference between the calculated results by two commonly used methods. Experimental fitting and simulation methods are also briefly reviewed to guide future research on shale gas adsorption.

58 GEOSCIENCES↗

CFD modeling of near-wall combustion and unburned methane prediction in natural gas spark ignition engines

Natural gas-powered engines play a critical role in gas drilling, compression, and transmission sectors, but methane (CH 4 ) from engine combustion slip can be significant over their lifespan, contributing to atmospheric pollution and signaling reduced engine efficiency. Here, to address this challenge, computational fluid dynamics (CFD) simulations offer valuable insights into the in-cylinder combustion process, enabling the optimization of combustion strategies and engine designs to minimize unburned CH 4 slip. This study aims to evaluate and improve combustion models for simulating the combustion process and predicting unburned CH 4 concentrations in natural gas spark-ignition (SI) engines, including engines that are part of combined reformer-engine systems. Specifically, the performance of two flamelet-based combustion models—the Extended Coherent Flame Model (ECFM) and the G-equation model—was assessed using experimental engine data collected under varying excess-air ratio (λ) conditions and fuel compositions, including natural gas and syngas blends. In addition, to enhance the predictive capabilities of the G-equation model, a flame-wall interaction (FWI) sub-model was integrated into its framework. The effects of its model parameters, such as quenching and influence distance, on combustion behavior and unburned methane predictions were analyzed in detail. The ECFM tended to predict delayed combustion phasing under diluted mixture conditions, resulting in overprediction of unburned CH 4 concentrations. In contrast, the G-equation model provided reasonable predictions of combustion pressure, while representing higher the CH 4 reduction rate across the operating condition compared to experimental data. Incorporating the FWI sub-model—with the quenching distance calculated based on a pressure-dependent relation (P -0.48 ) and a fixed influence distance of 1.5 mm—further improved the G-equation model’s accuracy in predicting CH 4 reduction rates without compromising its ability to simulate the combustion process.

Combustion model↗

Third-body stabilization of supercritical CO 2 in CO oxidation: development and application of a ReaxFF force field for the CO/O/CO 2 system

Supercritical CO 2 (scCO 2 ) plays a crucial role as a solvent in separation processes, advanced power cycles, and materials processing. Nonetheless, the atomistic comprehension of how the dense scCO 2 matrix influences the fundamental reaction of carbon monoxide (CO) is still insufficiently explored. Experimental studies and molecular dynamics (MD) simulations frequently fail to detect the highly reactive, transient intermediates, such as atomic oxygen (O), that drive these reactions. Here, to address this issue, we have developed a novel ReaxFF reactive force field for the CO 2 /CO/O system. The force field parameters were calibrated using density functional theory and second-order Møller-Plesset calculations to model CO 2 crystal properties, intermolecular interactions, bond dissociation curves, and reaction energy barriers. The force field reproduces the cohesive energy of the CO 2 crystal, the pressure characteristics of bulk scCO 2 , the equation-of-state behavior over a wide pressure–density range, the pressure dependence of the C–O bond length under compression, and the structural properties of liquid and scCO 2 , as documented by experiments, ab-initio MD, and prominent non-reactive models. The force field was subsequently applied to study the CO + O → CO 2 reaction. In a dilute environment, the reaction is inefficient as the newly formed CO 2 rapidly dissociates due to excess kinetic and potential energy acquired from the exothermic reaction. Conversely, in a dense scCO 2 environment, the surrounding matrix acts as an efficient third body, stabilizing the emerging CO2 product via molecular collisions. Statistical analysis confirms an average excess energy dissipation of 133.9 ± 3.6 kcal/mol over 112.4 ± 17.9 ps. Kinetic energy decomposition reveals that ∼ 92% of the excess kinetic energy is stored in internal (rotational and vibrational) degrees of freedom. This ReaxFF force field establishes a mechanistic foundation for third-body stabilization in dense reactive environments.

Chowdhury, Emdadul Haque [Pennsylvania State Univ.↗

Analytic model of the remobilization of pinned glide dislocations: Including dislocation drag from phonon wind

Here, we discuss the effect of a non-constant dislocation drag coefficient on the very high strain rate regime within an analytic model describing mobile-immobile dislocation intersections applicable to fcc polycrystals. Based on previous work on dislocation drag, we estimate its temperature and pressure dependence and its effects on stress–strain rate relations. In the high temperature regime, we show that drag can remain the dominating effect even down to intermediate strain rates. We also discuss the consequences of having a limiting dislocation velocity, a feature which is typically predicted by analytic models of dislocation drag, but which is somewhat under debate because a number of MD simulations predict supersonic dislocations.

42 ENGINEERING↗