Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLATES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Bipolar plate flow channel designs for vanadium redox flow battery: a review

Vanadium redox flow battery is one of the preferred systems for grid scale energy storage due to long service life (>20000 cycles), higher efficiency (>85 %), deep discharge capability (>95 % DoD), and inherent scalability and safety. Among system components, flow field is most critical as it governs electrolyte distribution, mass transport and hydraulic performance. Here, this review examines emerging flow channel geometries, highlighting the impact of channel width (0.66 to 1.5 mm), depth (1 to 1.5 mm) and land width (0.5 to 1.5 mm) can reduce pressure drop to <10 kPa while enabling power densities above 600 mW.cm -2 . A key finding is that low channel width to depth ratio (<1) enhances voltage and energy efficiencies by improving under rib convection. The review also provides an overview of progress and perspective in bipolar plate materials, manufacturability, and shunt current mitigation strategies for stack scaling up. Cost analysis emphasizes the influence of flow field designs on the levelized cost of storage and pathways towards the US DOE's $\$$0.05 per kWh energy generation cost target. In addition, opportunities for AI/ML/DT tools assisted design and data driven optimization strategies are also outlined to accelerate next generation flow field development.

Efficiency optimization↗

Unravelling fast-charging degradation in NMC/Gr pouch cells: Lithium plating and SEI properties

As fast-charging technology expands across the electric vehicle and emerging energy-storage applications, understanding its impact on battery performance and longevity is critical. In this study, 1.8 Ah LiNi 0.6 Mn 0.2 Co 0.2 O 2 /graphite pouch cells were charged at various charging rates (0.5C, 2C, 4C, and 6C) to investigate the degradation mechanisms. Our results showed that well-designed NMC/Gr pouch cells could reach over 1000 cycles with a 2C charging rate, while only reaching around 500 cycles with 4C and 6C charging rates. Fast-charging effects on NMC and graphite electrodes were obtained through a series of post-mortem characterizations, including electrochemical impedance spectroscopy (EIS), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS). Although higher charging rates cause pulverization of NMC secondary particles, the dominant degradation mechanism driving the fading of fast-charging-related performance lies in the graphite anode, where lithium plating and LiF-rich solid electrolyte interphase (SEI) formation result in Li inventory loss and impedance growth. The postmortem results suggest that the formation of a LiF-rich SEI, which exacerbates anode impedance and some irreversible Li + ion loss, is likely driven by the substantial decomposition of PF 6 − during fast charging, an effect often overlooked in smaller laboratory-scale studies.

Luo, Mei [Argonne National Laboratory (ANL), Argon↗

Toughening mechanism of inter-critical heat-affected zone in a 690 MPa grade rack plate steel

Highlights: • Relationship between toughness and microstructure was confirmed. • The toughness of ICHAZ is higher than that of FGHAZ. • Fine bainitic microstructure in ICHAZ plays an important role on improving toughness. • The homogeneous distribution of dislocation and local strain facilitate the plastic deformation prior fracture. - Abstract: The inter-critical heat-affected zone (ICHAZ) and fine grain heat-affected zone (FGHAZ) of a 690 MPa grade rack plate steel were simulated by Gleeble3500 simulator. The toughening mechanism of ICHAZ was clarified by analyzing microstructural characteristics and instrumental Charpy impact tests. The study showed that the ICHAZ had higher toughness than FGHAZ. And the microstructure in FGHAZ was martensite, while bainitic microstructure was obtained in ICHAZ. Both the prior austenite grain size and effective grain size of ICHAZ were smaller than that of FGHAZ, which played an important role in improving the toughness of ICHAZ. It was found that the extensive plastic deformation prior fracture in ICHAZ could consume large energy during crack initiation and propagation. The large plastic deformation capacity of ICHAZ was related to the large fraction of large-angle boundaries and low dislocation density, as well as the homogeneous distribution of local strain and geometrically necessary dislocations.

36 MATERIALS SCIENCE↗

Coarse-grained methods for heterogeneous vesicles with phase-separated domains: Elastic mechanics of shape fluctuations, plate compression, and channel insertion

We develop coarse-grained particle approaches for studying the elastic mechanics of vesicles with heterogeneous membranes having phase-separated domains. We perform simulations both of passive shape fluctuations and of active systems where vesicles are subjected to compression between two plates or subjected to insertion into narrow channels. Analysis methods are developed for mapping particle configurations to continuum fields with spherical harmonics representations. Heterogeneous vesicles are found to exhibit rich behaviors where the heterogeneity can amplify surface two-point correlations, reduce resistance during compression, and augment vesicle transport times in channels. The developed methods provide general approaches for characterizing the mechanics of coarse-grained heterogeneous systems taking into account the roles of thermal fluctuations, geometry, and phase separation.

97 MATHEMATICS AND COMPUTING↗

Preactivated zeolite nanosheet plate-tiled membrane on porous PVDF film: Synthesis and study of proton-selective ion conduction

Preactivated MFI zeolite nanosheet plates (ZNPs) with large areas (~2.0 × 2.0 μm 2 ) and nanometer thicknesses (~60 nm) were prepared directly in liquid-dispersed state. The individual ZNP was a stack of 4-nm-thick single crystalline zeolite nanosheets (ZNs) interlinked by Si–O–Si bonds between neighboring ZN surfaces. The dispersed open-pore ZNPs allowed formulating suspensions for tiling ZNP membranes on polymer substrates without requiring post-coating activation. A pinhole-free ZNP-tiled (ZNPT) membrane has been achieved on macroporous PVDF film by a self-repairing vacuum-assisted filtration coating method. The resultant ZNPT layer was ~500 nm-thick consisting of about 7 ZNP layers with inter-ZNP width and inter-ZNP entrance porosity around 9 nm and 2%, respectively. The ZNPT-PVDF membrane exhibited high selectivity to proton transport over vanadyl ion and low resistances to proton conduction in aqueous solutions. The membrane also demonstrated to function as an efficient ion separator for the vanadium redox flow battery. The reported synthesis of preactivated ZNP suspension may overcome the major hurdle to realizing polymer-supported ZN membranes, which is the inefficiency of existing methods in obtaining readily dispersible open-pore ZNs. Finally, the ZNPT-PVDF membrane can be a more affordable and sustainable alternative to the Nafion-based ion separation membranes.

36 MATERIALS SCIENCE↗

Deformation and fracture of explosion-welded Ti/Al plates: A synchrotron-based study

Here, explosion-welded Ti/Al plates are characterized with energy dispersive spectroscopy and x-ray computed tomography, and exhibit smooth, well-jointed, interface. We perform dynamic and quasi-static uniaxial tension experiments on Ti/Al with the loading direction either perpendicular or parallel to the Ti/Al interface, using a mini split Hopkinson tension bar and a material testing system in conjunction with time-resolved synchrotron x-ray imaging. X-ray imaging and strain-field mapping reveal different deformation mechanisms responsible for anisotropic bulk-scale responses, including yield strength, ductility and rate sensitivity. Deformation and fracture are achieved predominantly in Al layer for perpendicular loading, but both Ti and Al layers as well as the interface play a role for parallel loading. The rate sensitivity of Ti/Al follows those of the constituent metals. For perpendicular loading, single deformation band develops in Al layer under quasi-static loading, while multiple deformation bands nucleate simultaneously under dynamic loading, leading to a higher dynamic fracture strain. For parallel loading, the interface impedes the growth of deformation and results in increased ductility of Ti/Al under quasi-static loading, while interface fracture occurs under dynamic loading due to the disparity in Poisson's contraction.

36 MATERIALS SCIENCE↗

Understanding the interaction of extension twinning and basal-plate precipitates in Mg-9Al using precession electron diffraction

Precession electron diffraction is used to characterize the interaction between ${10\bar{1}2}$ tensile twins and basal plate-like precipitates in a post-deformed, precipitate-dispersed Mg-9Al micropillar. We observed a heterogeneous distribution of precipitates in the micropillar sample, which enabled the study of the different stages involved in twin precipitate interactions. We show that twin nucleation was promoted, taking place on the surface, as well as from the interior of the micropillar. Twin tip propagation and twin growth were hindered by the precipitates. Twin tips either were arrested by precipitates and new twins formed on the other side of the precipitate, or continued to grow around the precipitate without the re-nucleation events. During twin thickening, the precipitates did not significantly alter the shear-dominant twin boundary migration mechanism, as evidenced by the relatively flat twin boundaries around the partially embedded precipitates. However, the twin boundary migration was retarded by the precipitates, especially in regions confined by closely-spaced precipitates.

36 MATERIALS SCIENCE↗

Tailoring copper current collector roughness and crystallographic orientation to improve lithium plating

Secondary lithium metal batteries are of great interest due to a high theoretical energy density, but rechargeability is limited by the formation of lithium dendrites that lead to internal short circuits and catastrophic cell failure. Mitigating dendrites through uniform current distribution at the current collector is a promising solution to enabling long cycle life of lithium metal electrodes. Here, the impact of copper crystal orientation and roughness on electrochemically deposited lithium morphology is studied. For 50 cycles, the capacity retention from greatest to least followed polycrystalline copper 95 ± 1 % (MC-PC) ≥ 94.55 ± 0.01 % Cu (110) > 93.0 ± 0.4 % Cu(111) > 75.8 ± 0.1 % Cu(100). Cu(100) performed the worst in all cases with shorts occurring frequently before reaching 50 cycles. Cryo-scanning electron microscopy images showed that after 50 cycles, MC-PC Cu had the best lithium morphology, but at early cycles, Cu(111) formed the densest lithium layer. MC-PC Cu had the most uniform lithium nucleation which may have been caused by increased roughness relative to the single crystal samples. When polycrystalline Cu (F-PC) roughness was systematically controlled, the cumulative Coulombic efficiency increased from about 0.3–0.5 with increasing roughness from an Ra of about 10–40 nm. Lastly, plating rates were studied. Slower rates of 0.25 mA/cm 2 exhibited denser lithium morphology in all cases as compared to 0.5 and 1.0 mA/cm 2 , but the relative porosity of Li deposited on the different current collectors depended on the rate applied.

Copper↗

Development of a New Fast Shower Maximum Detector Based on Microchannel Plates Photomultipliers (MCP-PMT) as an Active Element

One possibility to make a fast and radiation resistant shower maximum (SM) detector is to use a secondary emitter as an active element. We present below test beam results, obtained with different types of photodetectors based on microchannel plates (MCPs) as the secondary emitter. We performed the measurements at the Fermilab Test Beam Facility with 120GeV proton beam and 12GeV and 32GeV secondary beams. The goal of the measurement with 120GeV protons was to determine time resolution for minimum ionizing particles (MIPs). The SM time resolution we obtained for this new type of detector is at the level of 20-30ps. We estimate that a significant contribution to the detector response originates from secondary emission of the MCP. This work can be considered as the first step in building a new type of calorimeter based on this principle.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Passive assay of plutonium metal plates using a fast-neutron multiplicity counter

Here, we developed a fast-neutron multiplicity counter based on organic scintillators (EJ-309 liquid and stilbene). The system detects correlated photon and neutron multiplets emitted by fission reactions, within a gate time of tens of nanoseconds. The system was used at Idaho National Laboratory to assay a variety of plutonium metal plates. A coincidence counting strategy was used to quantify the 240 Pu effective mass of the samples. Coincident neutrons, detected within a 40-ns coincidence window, show a monotonic trend, increasing with the 240 Pu-effective mass (in this work, we tested the 0.005–0.5 kg range). After calibration, the system estimated the 240 Pu effective mass of an unknown sample ( 240 Pu eff >50 g) with an uncertainty lower than 1% in a 4-min assay time.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Demonstrating imaging plate detector stacks for proton radiography using exploding pusher capsules

A new detector design has been fielded on the Omega-60 laser facility using a D 3 He backlighter capsule to radiograph a magnetized experiment. D 3 He capsules produce a low flux (~ 10 8 total yield in 4π) of protons requiring detectors with close-to single-particle sensitivity to be employed. The new detector stack consisted of both imaging plate (IP) and CR-39 to detect 14.7 MeV protons where, historically, only CR-39 has been used. IP is sensitive to significant contributions in signal from both x-rays and protons so additional filtering has to be added to attenuate the x-rays. Here, the signals and features observed from a single shot are detected by both IP and CR-39, giving confirmation that it is protons creating the signatures on the IP. Measurements of PSL/pixel are used to calculate approximate on-shot proton yields and agree with commonly measured yields. A second IP is used at the rear of the stack to measure, and subsequently remove, a background signal. The spatial resolution at the IP is limited, primarily, by a range of proton energies with varying deflections being recorded at the detector, causing potential ‘blurring’ of features. We find for this setup that the blurring effect is less than the smallest identifiable features observed at the detector, and therefore of minimal impact. A large benefit to this new stack design is that IP can be scanned and processed on much faster timescales than CR-39 allowing for prompt shot feedback. Future designs and modifications to the stack design fielded on this experiment could help improve the contrast of the radiograph on IP, as well as detecting protons produced at alternative energies.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Analysis of impact to optical environment of the land by flat-plate and array of tracking PV panels

The impact to the optical environment result from shading of PV panels becomes concerned. This paper describes how to calculate illumination level on the land around tracking PV (both isolated and arrayed) panel. The land under the flat-plate PV is dark by shading, but the influence from the tracking PV is not very significant, typically half in average. This is because shadow by tracking panel moves. The shading influence is further decreased with the increase of pedestal height. We report with this advantage, tracking PV can be combined with agriculture as a double use of the land.

14 SOLAR ENERGY↗

Nanotubes, Plates, and Needles: Pathway-Dependent Self-Assembly of Computationally Designed Peptides

Computationally designed peptides form desired antiparallel, tetrameric coiled-coil bundles that hierarchically assemble into a variety of well-controlled nanostructures depending on aqueous solution conditions. The bundles selectively self-assemble into different structures: nanotubes, platelets, or needle-like structures at solution pH values of 4.5, 7, and 10, respectively. The self-assembly produces hollow tubes or elongated needle-like structures at pH conditions associated with charged bundles (pH 4.5 or 10); at neutral pH, near the pI of the bundle, a plate-like self-assembled structure forms. Transmission electron microscopy and small-angle X-ray scattering show the nanotubes to be uniform with a tube diameter of ~13 nm and lengths of up to several μm, yielding aspect ratios >1000. Combining the measured nanostructure geometry with the apparent charged states of the constituent amino acids, a tilted-bundle packing model is proposed for the formation of the homogeneous nanotubes. Here, this work demonstrates the successful use of assembly pathway control for the construction of nanostructures with diverse, well-structured morphologies associated with the folding and self-association of a single type of molecule.

59 BASIC BIOLOGICAL SCIENCES↗

Plating Precious Metals on Nonprecious Metal Nanoparticles for Sustainable Electrocatalysts

Precious metals have broad applications in modern industry and renewable energy technologies. The high cost and limited availability of these materials, however, have caused a grand challenge for sustainability. In this work, we report on the plating of a precious metal on nonprecious metal nanoparticles for the development of sustainable electrocatalysts. Cobalt/platinum core/shell (denoted as Co@Pt) nanoparticles were synthesized via seed-mediated growth. The Co seeds were first synthesized by thermal decomposition of cobalt carbonyl, and the Pt shell was overgrown in situ by adding platinum acetylacetonate (Pt(acac) 2 ). The galvanic replacement reaction between Co and the Pt precursor was successfully suppressed by taking advantage of CO (generated from the decomposition of cobalt carbonyl) as the stabilizing ligand and/or reducing agent. Moreover, the obtained Co@Pt nanoparticles were found to exhibit enhanced catalytic activity for the oxygen reduction reaction (ORR).

36 MATERIALS SCIENCE↗

Atomistic Defect Makes a Phase Plate for the Generation and High-Angular Splitting of Electron Vortex Beams

Topological defects in solid-state materials by breaking the translational symmetry offer emerging properties that are not present in their parental phases. For example, edge dislocations—the 2π phase-winding topological defects—in antiferromagnetic NiO crystals can exhibit ferromagnetic behaviors. We study how these defects could give rise to topological orders when they interact with a high-energy electron beam. To probe this interaction, we formed a coherent electron nanobeam in a scanning transmission electron microscope and recorded the far-field transmitted patterns as the beam steps through the edge dislocation core in [001] NiO. Surprisingly, we found the amplitude patterns of the <020> Bragg disks evolve in a similar manner to the evolution of an annular solar eclipse. Using the ptychographic technique, we recovered the missing phase information in the diffraction plane and revealed the topological phase vortices in the diffracted beams. Through atomic topological defects, the wave function of electrons can be converted from plane wave to electron vortex. Technologically, this approach provides a feasible route for the fabrication of phase plates that can generate electron vortex beams with an angular separation that is three orders of magnitude larger than what traditional nanofabrication technology can offer. This advance will enable the collection of magnetic circular dichroism spectra with high spatial resolution and high efficiency, boosting the understanding of the relationship between symmetry breaking and magnetic property of individual topological defect at the atomic scale.

36 MATERIALS SCIENCE↗

Strong Upper-Plate Heterogeneity at the Hikurangi Subduction Margin (North Island, New Zealand) Imaged by Adjoint Tomography

We use earthquake-based adjoint tomography to invert for three-dimensional structure of the North Island, New Zealand, and the adjacent Hikurangi subduction zone. The study area, having a shallow depth to the plate interface below the North Island, offers a rare opportunity for imaging material properties at an active subduction zone using land-based measurements. Starting from an initial model derived using ray tomography, we perform iterative model updates using spectral element and adjoint simulations to fit waveforms with periods ranging from 4–30 s. We perform 28 model updates using an L-BFGS optimization algorithm, improving data fit and introducing P- and S-wave velocity changes of up to ±30%. Resolution analysis using point spread functions show that our measurements are most sensitive to heterogeneities in the upper 30 km. The most striking velocity changes coincide with areas related to the active Hikurangi subduction zone. Lateral velocity structures in the upper 5 km correlate well with New Zealand geology. Here, the inversion reveals increased along-strike heterogeneity on the margin. In Cook Strait we observe a low-velocity zone interpreted as deep sedimentary basins. In the central North Island, low-velocity anomalies are linked to surface geology, and we relate velocity structures at depth to crustal magmatic activity below the Taupō Volcanic Zone.

58 GEOSCIENCES↗

Thermally Significant Fluid Seepage Through Thick Sediment on the Juan de Fuca Plate Entering the Cascadia Subduction Zone

We use heat flux measurements colocated with seismic reflection profiles over a buried basement high on the Juan de Fuca plate ∼25 km seaward of the deformation front offshore Oregon to test for the presence of hydrothermal circulation in the oceanic crust. We also revisit heat flux data crossing a buried basement high ∼25 km seaward of the deformation front ∼150 km north, offshore Washington. Seafloor heat flux is inversely correlated with sediment thickness, consistent with vigorous hydrothermal circulation in the basement aquifer homogenizing temperatures at the top of the basement. Heat flux immediately above the summit of the basement highs is greater than expected solely from conduction. Fluid seepage at rates of ∼2.6–5.4 cm yr −1 in a 1–1.5 km-wide conduit through ∼800–1,300 m thick sediment sections above these basement highs can explain these observations. Observations of thermally significant fluid seepage through sediment >225 m thick on oceanic crust are unprecedented. High sediment permeability, high fluid overpressure in the basement, or a combination of both is required to drive fluid seepage at the observed rates. We infer that rapid seepage occurs because the basement highs rise above the low permeability basal sediment with their tops protruding into the base of high permeability Nitinat or Astoria Fan sediment. Seepage from basement highs penetrating into the submarine fans can affect the thermal state of crust entering the subduction zone.

58 GEOSCIENCES↗

Nanofocusing of hard X-ray free electron laser pulses using diamond based Fresnel zone plates

A growing number of X-ray sources based on the free-electron laser (XFEL) principle are presently under construction or have recently started operation. The intense, ultrashort pulses of these sources will enable new insights in many different fields of science. A key problem is to provide x-ray optical elements capable of collecting the largest possible fraction of the radiation and to focus into the smallest possible focus. As a key step towards this goal, we demonstrate here the first nanofocusing of hard XFEL pulses. We developed diamond based Fresnel zone plates capable of withstanding the full beam of the world’s most powerful x-ray laser. Using an imprint technique, we measured the focal spot size, which was limited to 320 nm FWHM by the spectral band width of the source. A peak power density in the focal spot of 4&times;10 17 W/cm 2 was obtained at 70 fs pulse length.

36 MATERIALS SCIENCE↗