Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PELLETING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Reducing the L-H transition power threshold in ITER-similar-shape DIII-D hydrogen plasmas

Recent dedicated DIII-D experiments in low-torque, ITER-similar-shape (ISS) hydrogen plasmas (at a plasma current I p ~ 1.5 MA and ITER-similar edge safety factor q 95 ~ 3.6) show that the L-H transition power threshold P LH can be reduced substantially (~30%) with L-mode helium admixtures n He /n e $\leqslant$ 25%. In the ensuing H-mode, helium ion fractions n He /n H remain below 25%. H-mode normalized pressure and confinement quality are only slightly affected by helium seeding, and Z eff $\leqslant$ 2.15 (including helium and carbon content). The plasmas investigated here are electron-heat dominated, with temperatures T e (0)/T i (0) $\geqslant$ 1 and edge heat flux ratio Q e /Q i (ρ = 0.95) ~ 1.2–1.5. Without mitigation, P LH is higher by a factor of 2–3 in comparison to similar ISS deuterium plasmas. ISS hydrogen plasmas with lower plasma current I p ~ 1 MA (increased edge safety factor q 95 ~ 5.1) exhibit a substantially lower power threshold. This plasma current dependence, also observed previously on ASDEX-U and in JET, is not accounted for by the commonly used 2008 ITPA multi-machine threshold scaling, but could potentially allow H-mode access at marginal heating power during the initial plasma current ramp-up. Attempts to reduce P LH with low-field- and high-field-side hydrogen pellet injection, using 1.7 mm diameter pellets, have not demonstrated a robust threshold reduction, in contrast to successful earlier experiments with larger 2.7 mm pellets. Finally, techniques for reducing P LH are very important for ITER, in particular for accessing H-mode in hydrogen plasmas during the Pre-Fusion Power Operation-1 (PFPO-1) campaign with marginal auxiliary heating power (20–30 MW of ECH).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fully-coupled engineering and mesoscale simulations of thermal conductivity in UO2 fuel using an implicit multiscale approach

Reactor fuel performance is sensitive to microstructure changes during irradiation (such as fission gas and pore formation). This study proposes an approach to capture microstructural changes in the fuel by a two-way coupling of a mesoscale phase field irradiation model to an engineering scale, finite element calculation. This work solves the multiphysics equation system at the engineering-scale in a parallel, fully-coupled, fully-implicit manner using a preconditioned Jacobian-free Newton Krylov method (JFNK). A sampling of the temperature at the Gauss points of the coarse scale is passed to a parallel sequence of mesoscale calculations within the JFNK function evaluation phase of the calculation. The mesoscale thermal conductivity is calculated in parallel, and the result is passed back to the engineering-scale calculation. As this algorithm is fully contained within the JFNK function evaluation, the mesoscale calculation is nonlinearly consistent with the engineering-scale calculation. Further, the action of the Jacobian is also consistent, so the composite algorithm provides the strong nonlinear convergence properties of Newton's method. The coupled model using INL's \bison\ code demonstrates quadratic nonlinear convergence and good parallel scalability. Initial results predict the formation of large pores in the hotter center of the pellet, but few pores on the outer circumference. Thus, the thermal conductivity is is reduced in the center of the pellet, leading to a higher internal temperature than that in an unirradiated pellet.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Digestibility of the defatted microalgae Nannochloropsis sp. and Desmodesmus sp. when fed to Atlantic salmon, Salmo salar

The aim of the study was to investigate the apparent digestibility coefficient (ADC) of defatted biomass derived from microalgae Nannochloropsis sp. and Desmodesmus sp. when fed to Atlantic salmon postsmolts in seawater. Two experiments, one employing cold-pelleted and the other employing extruded pellets, were carried out to determine the ADC of dry matter (DM), protein, ash and energy. The test feeds consisted of a fishmeal-based reference feed and the algal biomass, at a ratio of 70:30, and yttrium oxide as the inert marker. The ADC of DM and protein in fish fed microalgae-incorporated cold-pelleted feeds were significantly higher for Nannochloropsis sp. compared with Desmodesmus sp. Here, the Nannochloropsis sp. inclusion in extruded feeds also led to higher ADCs of DM and energy compared with Desmodesmus sp. The extrusion processing significantly increased the ADC of ash in both defatted microalgae biomass, as well as ADCs of DM in Nannochloropsis and protein in Desmodesmus sp. In conclusion, the microalga Nannochloropsis sp. was more digestible than Desmodesmus sp., and extrusion processing can be used as a means to improve digestibility of certain nutrients.

59 BASIC BIOLOGICAL SCIENCES↗

Biomass market dynamics supporting the large‐scale deployment of high‐octane fuel production in the United States

Abstract US Department of Energy research aimed at co‐optimizing fuels and engine performance identified several bioblendstocks that can improve fuel economy including an aromatic‐rich hydrocarbon derived from woody biomass. This work supports an analysis of its large‐scale deployment implying a production target of approximately 15 billion liters of bioblendstock for the supply of 57 billion liters of high‐octane fuel by 2050. It simulates potential transition pathways to lignocellulosic feedstock market structures capable of supplying a mature biorefining industry at this scale. In the present absence of biorefineries, transitions are modeled via nonbiofuel feedstock markets, so‐called companion markets. The resource distribution across several demand industries is simulated to determine biomass availability and price dynamics over time. Results indicate that the wood supply base is mainly influenced by traditional markets including housing and pulp and paper. The selected companion market of wood pellet combustion for heat and electricity generation is found to positively stimulate biomass mobilization, especially in the initial absence of biorefineries. Eventually, biorefineries are found to be able to out‐compete the companion market. As such, they directly benefit from the processing (i.e., pelleting) capacity established to produce commodity‐type intermediates for the companion market. We conclude that the amount of bioblendstock produced is directly related to the size of the companion market (and its pelleting capacity). An initially larger companion market generates up to 20 million dry tonnes of additional feedstock, equivalent to 27 commercial‐scale biorefineries, or an additional production of 5 billion liters by 2050. Distinguishing between industry‐specific feedstock preferences based on average biomass quality characteristics, this analysis goes beyond past research efforts that assume automatic fungibility across different feedstocks. Improving engine performance is a key driver for the promotion of low‐carbon fuels derived from bioblendstocks. This analysis portrays feedstock market transition pathways for their large‐scale deployment.

09 BIOMASS FUELS↗

Solution-Derived, Chloride-Containing Minerals as a Waste Form for Alkali Chlorides

Sodalite [Na8(AlSiO4)6Cl2] and cancrinite [(Na,K)6Ca2Al6Si6O24Cl4] are environmentally stable, chloride-containing minerals and are a logical waste form option for the mixed alkali chloride salt waste stream that is generated from a proposed electrochemical separations process during nuclear fuel reprocessing. Due to the volatility of chloride salts at moderate temperatures, the ideal processing route for these salts is a low-temperature approach such as the sol-gel process. The sodalite structure can be easily synthesized by the sol-gel process; however, it is produced in the form of a fine powder with particle sizes on the order of 1–10 µm. Due to the small particle size, these powders require additional treatment to form a monolith. In this study, the sol-gel powders were pressed into pellets and fired to achieve > 90% of theoretical density. The cancrinite structure, identified as the best candidate mineral form in terms of waste loading capacity, was only produced on a limited basis following the sol-gel process and converted to sodalite upon firing. Here we discuss the sol-gel process specifics, chemical durability of select waste forms, and the steps taken to maximize chloride-containing phases, decrease chloride loss during pellet firing, and increase pellet densities.

cancrinite↗

Implementation of a Model Predictive Control Strategy to Regulate Temperature Inside Plug-Flow Solar Reactor With Countercurrent Flow

Abstract Solar-driven thermochemical energy storage systems are proven to be promising energy carriers (solar fuels) to utilize solar energy by using reactive solid-state pellets. However, the production of solar fuel requires a quasi-steady-state process temperature, which represents the main challenge due to the transient nature of solar power. In this work, an adaptive model predictive controller (MPC) is presented to regulate the temperature inside a tubular solar reactor to produce solid-state solar fuel for long-term thermal storage systems. The solar reactor system consists of a vertical tube heated circumferentially over a segment of its length by concentrated solar power, and the reactive pellets (MgMn2O4) are fed from the top end and flow downwards through the heated tube. A countercurrent flowing gas supplied from the lower end interacts with flowing pellets to reduce it thermochemically at a temperature range of 1000—1500 °C. A low-order physical model was developed to simulate the dynamics of the solar reactor including the reaction kinetics, and the proposed model was validated numerically by using a 7-kW electric furnace. The numerical model then was utilized to design the MPC controller, where the control system consists of an MPC code linked to an adaptive system identification code that updates system parameters online to ensure system robustness against external disturbances (sudden change in the flow inside the reactor), model mismatches, and uncertainty. The MPC controller parameters are tuned to enhance the system performance with minimum steady-state error and overshoot. The controller is tested to track different temperature ranges between 500 °C and 1400 °C with different particles/gas mass flowrates and ramping temperature profiles. Results show that the MPC controller successfully regulated the reactor temperature within ± 1 °C of its setpoint and maintained robust performance with minimum input effort when subjected to sudden changes in the amount of flowing media and the presence of chemical reaction.

Engineering↗

FATIGUE BEHAVIOR OF SPENT NUCLEAR FUEL RODS IN SIMULATED TRANSPORTATION ENVIRONMENT

Nuclear fuel rod is composed of cladding tube and a specified number of fuel pellets contained. In the United States, spent nuclear fuel (SNF) is expected to be transported to at least one storage facility before permanent disposal. The fatigue behavior of spent nuclear fuel (SNF) rods under reversed cyclic bending must be understood in order to evaluate their vibration integrity in a transportation environment. This is especially important for high-burnup SNFs (>45 GWd/MTU). This report presents the experimental results related to Zircaloy (Zry)-4 - based surrogate rods and high-burnup SNFs, based on recent work performed at Oak Ridge National Laboratory (ORNL). The surrogate rod was made of Zry-4 cladding and alumina pellets, and high-burnup fuel rods were discharged from H.B. Robinson pressurized water reactor. The reversed cyclic bending testing was conducted at 5 Hz under loading control. The effect of pre-hydriding and burnup or irradiation on the flexural rigidity and fatigue life of cladding-pellet system were discussed. The fatigue data obtained are extremely useful to the future certification of SNF storage and transportation cask.

Wang, Jy-An John↗

Determining Infrared Optical Constants for Dolomite using Single Angle Reflectance and Spectroscopic Ellipsometry

The optical constants, namely the real (n) and imaginary (k) parts of the complex refractive index, are of particular interest to generate the infrared (IR) spectra of liquid and solid materials in different morphologies. To obtain n/k, however, most materials are typically not found in the monolithic forms necessary to easily measure n/k, and thus require the use of other methods such as pressing powders to form planar, specularly-reflective pellets. In this work dolomite crystals are measured using fixed-angle IR reflectance spectroscopy in both 1) a monolithic form with the crystal fixed in epoxy and polished, but data are also recorded from 2) pressed-pellet forms of powders of the same mineral using the same spectroscopic protocols. First results for the two methods are compared. It was found that the measured reflectance can vary by as much as a factor of two between the dolomite crystals and the pressed powder forms. For the two-sample preparation approaches the preliminary spectra are compared and the implications and limitations of each method for determining the optical constants of given materials are discussed. Comparison to literature data suggest that polarization effects likely account for the differing amplitude results for reflectance (and hence the k -vectors): Dolomite is known to be biaxial with significantly differing ordinary and extraordinary rays; the pressed pellet method measures an ensemble of microcrystals in randomly oriented positions, whereas the single crystal maintains just one orientation relative to the optical axis.

ellipsometry, dolomite, complex refractive index, ↗

Laser-Induced Plasmas of Plutonium Dioxide in a Double-Walled Cell

Plutonium research has been stifled by the significant number of administrative controls and safety procedures, space and instrumentation limitations in radiological gloveboxes, and the potential for personnel and equipment contamination. To address the limited number of spectroscopic studies in Pu-bearing compounds in the current scientific literature, this work presents the use of double-walled cells (DWCs) in “clean” buildings/laboratories as an alternative to research in radiological gloveboxes. This study reports the first laser-induced breakdown spectroscopy (LIBS) experiments of a PuO 2 pellet contained within a DWC, where the formation of elemental (atomic and ionic) species as well as the evolution from elemental to molecular products (Pu x O y ) was measured. Raman spectroscopy was also used to characterize the surface of the ablated pellet and the particulates deposited on the window of the inner cell. The full width half-maximum of the T 2g band enabled us to obtain an estimate of the temperature at the pellet surface after the ablation pulse and the particulates based on the crystal lattice disorder. Particulates deposited on the window of the DWC during laser ablation were characterized using scanning electron microscopy, where molten irregular particulates and spheroids were observed. This exciting research conducted in a DWC describes our initial attempts to incorporate LIBS in the arsenal of spectroscopic tools for nuclear forensics applications.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Reversal bending fatigue test system for investigating vibration integrity of spent nuclear fuel during transportation

Transportation packages for spent nuclear fuel (SNF) must meet safety requirements under normal and accident conditions as specified by federal regulations. During transportation, SNF experiences unique conditions and challenges to cladding integrity due to the vibrational and impact loading during road or rail shipment. Oak Ridge National Laboratory (ORNL) has been developing testing capabilities that can be used to improve the understanding of the impacts on SNF integrity due to vibration loading, especially for high burn-up SNF in normal transportation operation conditions. This information can be used to meet the nuclear industry and U.S.Nuclear Regulatory Commission needs in the area of safety and security of SNF storage and transportation operations. The ORNL developed test system can perform reversal bending fatigue testing to evaluate both the static and dynamic mechanical response of SNF rods under simulated loads. The testing apparatus is also designed to meet the challenges of hot cell operation, including remote installation and detachment of the SNF test specimen, in situ test specimen deformation measurement, and implementation of a driving system suitable for use in a hot cell. The system contains a U frame set-up equipped with uniquely designed grip rigs to protect the SNF rod sample and to ensure valid test results, and uses three specially designed linear variable differential transformers to obtain the in situ curvature measurement. A variety of surrogate test rods have been used to develop and calibrate the test system as well as in performing a series of systematic cyclic fatigue tests. The surrogate rods include stainless steel (SS) cladding, SS cladding with cast epoxy and SS cladding with alumina pellet inserts simulating fuel pellets. Testing to date has shown that the interface bonding between the SS cladding and the alumina pellets has a significant impact on the bending response of the test rods as well as their fatigue strength. The failure behaviours observed from tested surrogate rods provide a fundamental understanding of the underlying failure mechanisms of the SNF surrogate rod under vibration,which has not been achieved previously. The newly developed device is scheduled to be installed in the hot cell in summer 2013 to test high burn-up SNF.

high burn up fuel↗

Disruption Mitigation System Developments and Design for ITER

A disruption mitigation system (DMS) is under design for ITER to inject sufficient material deeply into the plasma for rapid plasma thermal shutdown and collisional suppression of any resulting runaway electrons. Progress on the development and design of both a shattered pellet injector (SPI) that produces large solid cryogenic pellets to provide reliable deep penetration of material and a fast opening high flow rate gas valve for massive gas injection (MGI) is presented. Cryogenic pellets of deuterium and neon up to 25 mm in size have been formed and accelerated with a prototype injector and a full scale prototype MGI valve is now in testing. Implications of the design with respect to response time and reliability at the proposed injector locations on ITER are discussed.

Baylor, Larry↗

ALD Produced B 2 O 3 , Al 2 O 3 and TiO 2 Coatings on Gd 2 O 3 Burnable Poison Nanoparticles and Carbonaceous TRISO Coating Layers

This project will demonstrate the feasibility of using atomic layer deposition (ALD) to apply ultrathin neutron-absorbing, corrosion-resistant layers consisting of ceramics, metals, or combinations thereof, on particles for enhanced nuclear fuel pellets. Current pellet coating technology utilizes chemical vapor deposition (CVD) in a fluidized bed reactor to deposit thick, porous layers of C (or PyC) and SiC. These graphitic/carbide materials degrade over time owing to fission product bombardment, active oxidation, thermal management issues, and long-term irradiation effects. ALD can be used to deposit potential ceramic barrier materials of interest, including ZrO 2 , Y 2 O 3 :ZrO 2 (YSZ), Al 2 O 3 , and TiO 2 , or neutron-absorbing materials, namely B (in BN or B 2 O 3 ) and Gd (in Gd 2 O 3 ). This project consists of a two-pronged approach to integrate ALD into the next-generation nuclear plant (NGNP) fuel pellet manufacturing process:

36 MATERIALS SCIENCE↗

Low-Cost Phase Change Material for Building Envelopes

A low-cost PCM process consisting of conversion of fats and oils to PCM-range paraffins, and subsequent “encapsulation” of the paraffin using conventional plastic compounding/pelletizing equipment was demonstrated. The PCM pellets produced were field-tested in a building envelope application. This involved combining the PCM pellets with cellulose insulation, whereby 33% reduction in peak heat flux and 12% reduction in heat gain was observed (average summertime performance). The selling price of the PCM pellets produced according to this low-cost process is expected to be in the $\$ $1.50-$\$ $3.00/lb range, compared to current encapsulated PCM price of about $\$ $7.00/lb. Whole-building simulations using corresponding PCM thermal analysis data suggest a payback time of 8 to 16 years (at current energy prices) for an attic insulation retrofit project in the Phoenix climate area.

25 ENERGY STORAGE↗

CIRFT Testing of High-Burnup Used Nuclear Fuel Rods from the Pressurized Water Reactor and Boiling Water Reactor Environments (FY 2015 Status Report)

High burn-up spent nuclear fuel (SNF) cladding has a significant amount of microcracks and hydrides, which will reduce the stress intensity required for crack growth. The potential linking of microcracks during vibration loading could also reduce the fatigue threshold/incubation period significantly, accelerating fatigue failure. In addition to cladding damage, the microstructure of fuel pellets and the characteristics of the interfaces between fuel pellets and between fuel pellets and cladding are likely to be dramatically changed after high burn-up. These modifications can have a direct impact on the structural integrity and vibration response of SNF rods in transportation. As a result, vibration has been included as one of the mandatory testing conditions in the structural evaluation of packages used by the US Nuclear Regulation Commission (NRC) in transporting SNF (10 CFR §71.71). Prior to this program development, no current system is available to test the SNF and evaluate the performance of fuel rods during spent fuel transportation. The objective of this research is to develop a system that can appropriately test the response of high-burnup SNF rods in a simulated loading condition.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of the Relative Merits of Herbaceous and Woody Crops for Use in Tunable Thermochemical Processing

This report summarizes the work and findings of the grant work conducted from January 2009 until September 2011 under the collaboration between Ceres, Inc. and Choren USA, LLC. This DOE-funded project involves a head-to-head comparison of two types of dedicated energy crops in the context of a commercial gasification conversion process. The main goal of the project was to gain a better understanding of the differences in feedstock composition between herbaceous and woody species, and how these differences may impact a commercial gasification process. In this work, switchgrass was employed as a model herbaceous energy crop, and willow as a model short-rotation woody crop. Both crops are species native to the U.S. with significant potential to contribute to U.S. goals for renewable liquid fuel production, as outlined in the DOE Billion Ton Update (http://www1.eere.energy.gov/biomass/billion_ton_update.html, 2011). In some areas of the U.S., switching between woody and herbaceous feedstocks or blending of the two may be necessary to keep a large-scale gasifier operating near capacity year round. Based on laboratory tests and process simulations it has been successfully shown that suitable high yielding switchgrass and willow varieties exist that meet the feedstock specifications for large scale entrained flow biomass gasification. This data provides the foundation for better understanding how to use both materials in thermochemical processes. It has been shown that both switchgrass and willow varieties have comparable ranges of higher heating value, BTU content and indistinguishable hydrogen/carbon ratios. Benefits of switchgrass, and other herbaceous feedstocks, include its low moisture content, which reduce energy inputs and costs for drying feedstock. Compared to the typical feedstock currently being used in the Carbo-V® process, switchgrass has a higher ash content, combined with a lower ash melting temperature. Whether or not this may cause inefficiencies in the process, needs to be verified by long term test runs. Currently, there are not sufficient operational test data available for the Carbo-V® process for the utilization of higher ash content feedstocks. The application of currently evolving biomass pretreatment technologies, such as pelletization and torrefaction, will be able to expand the portfolio of biomass varieties and species acceptable in gasification processes. Tests showed that 6 mm diameter pellets of switchgrass were superior to 8 mm diameter pellets produced in a flat dye press, and that torrefaction of switchgrass produced an excellent (but currently costly) feedstock that could be handled, crushed, and combusted in a manner compatible with any coal-fed gasification facility. Ceres will use this information in the development of high yielding, dedicated energy crops specifically tailored for thermochemical conversion. CHOREN will make use of the information for improvement or development of low cost, highly efficient biomass gasification processes that convert a wide variety of biomass feedstocks to fuels, chemicals, heat and power via the production of tar free green syngas on an industrial scale.

09 BIOMASS FUELS↗

General Motors: Final Report for Hydrogen Storage Engineering Center of Excellence

As part of the HSECoE team, the GM team built system models and detailed transport models for on-board hydrogen storage systems using metal hydrides and adsorbent materials. Detailed transport models have been developed for both the metal hydride and adsorbent systems with a focus on optimization of heat exchanger designs with the objective of minimizing the heat exchanger mass. We also performed work in collaboration with our partners on storage media structuring and enhancement studies for the metal hydride and adsorbent materials. Since the hydrogen storage materials are generally characterized by low density and low thermal conductivity, we conducted experiments to form pellets and add thermal conductivity enhancers to the storage material, and to improve cycling stability and durability of the metal hydride and adsorbent materials. Refueling of a MOF-5 pellet with cryogenic hydrogen was studied by developing a detailed two-dimensional axisymmetric COMSOL® model of the process. The effects of pellet permeability, thermal conductivity, and thermal conductivity enhancers were investigated. Our key area of focus has been on designing and building a cryo-adsorption vessel for validation of cryo-adsorption models. The 3-L cryogenic tank was used to study the fast fill and discharge dynamics of a cryo-adsorbent storage system, both experimentally and numerically.

08 HYDROGEN↗

Experimental assessment of fuel-cladding interactions

A range of fuel concepts designed to better tolerate accident scenarios and reactor transients are currently undergoing fundamental development at national laboratories as well as university and industrial partners. Pellet-clad mechanical and chemical interaction can be expected to affect fuel failure rates experienced during steady state operation, as well as dramatically impact the response of the fuel form under loss of coolant and other accident scenarios. The importance of this aspect of fuel design prompted research initiated by AFC in FY14 to begin exploratory efforts to characterize this phenomenon for candidate fuelcladding systems of immediate interest. Continued efforts in FY15 and FY17 aimed to better understand and simulate initial pellet-clad interaction with little-to-no pressure on the pellet-clad interface. Reported here are the results from 1000 h heat treatments at 400, 500, and 600°C of diffusion couples pairing UN with a FeCrAl alloy, SiC, and Zr-based cladding candidate sealed in evacuated quartz ampoules. No gross reactions were observed, though trace elemental contaminants were identified.

36 MATERIALS SCIENCE↗