Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Materials characterization techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Versatile technique for assessing thickness of 2D layered materials by XPS

X-ray photoelectron spectroscopy (XPS) has been utilized as a versatile method for thickness characterization of various two-dimensional (2D) films. Accurate thickness can be measured simultaneously while acquiring XPS data for chemical characterization of 2D films having thickness up to approximately 10 nm. For validating the developed technique, thicknesses of few-layer graphene (FLG), MoS 2 and amorphous boron nitride (a-BN) layer, produced by microwave plasma chemical vapor deposition (MPCVD), plasma enhanced chemical vapor deposition (PECVD), and pulsed laser deposition (PLD) respectively, were accurately measured. The intensity ratio between photoemission peaks recorded for the films (C 1s, Mo 3d, B 1s) and the substrates (Cu 2p, Al 2p, Si 2p) is the primary input parameter for thickness calculation, in addition to the atomic densities of the substrate and the film, and the corresponding electron attenuation length (EAL). The XPS data was used with a proposed model for thickness calculations, which was verified by cross-sectional transmission electron microscope (TEM) measurement of thickness for all the films. The XPS method determines thickness values averaged over an analysis area which is orders of magnitude larger than the typical area in cross-sectional TEM imaging, hence provides an advanced approach for thickness measurement over large areas of 2D materials. The study confirms that the versatile XPS method allows rapid and reliable assessment of the 2D material thickness and this method can facilitate in tailoring growth conditions for producing very thin 2D materials effectively over a large area. Furthermore, the XPS measurement for a typical 2D material is non-destructive and does not require special sample preparation. Furthermore, after XPS analysis, exactly the same sample can undergo further processing or utilization.

2D film thickness↗

Pilot Testing of a Modular Oxygen Production System Using Oxygen Binding Adsorbents (Final Report)

In this project, RTI and Air Liquide have focused on the development of innovative oxygen separation materials and technologies based on reversibly binding of oxygen to enable smaller and cheaper air separations. In alignment with that object the team has had multiple achievements to advance the technology including: Synthesized and characterized novel M-CoSalen (RTIO2Sorb-1) material which showed a dynamic oxygen adsorption capacity in excess of 1wt%. Developed synthesis routes for RTIO2Sorb-1 with commercially relevant techniques and produced batches of 0.25kg and over 4 kg of total synthesis. Synthesized and characterized extrudate forms of the RTIO2Sorb-1 with relevant crush strength and maintained dynamic oxygen adsorption capacity in near 1wt%. Developed techniques for forming structured beds in fiber shapes with conventional materials. Developed a model for O 2 sorption processes to analyze various bed configurations and cycle parameters. Studied classic O 2 solid sorbents reported in the literature to learn oxygen binding mechanisms. Design a 10 kg/day O 2 VPSA pilot system with 2 or 4-bed operation. Completed a techno-economic analysis based on the experimental results and modeling. The overall objective of the project was to design, fabricate, and test a modular O 2 production system and perform a techno-economic analysis (TEA) after testing to determine the cost-benefit of the advanced modular air separation system. The goals of this technology development project were to achieve a bed-size factor (BSF) of less than 600 lb-adsorbent/TPD O 2 (ton/day O 2 ) (as compared with the state-of-the-art BSF of 850), and O 2 -purity greater than 95% at a cost that is projected to be equivalent or lower than the current state of the art (SOTA), commercially available large-scale cryogenic air separation systems. To achieve these goals and objective, the project team executed on (1) oxygen binding adsorbent optimization and scale up, (2) adsorbent material formation process studies to form the adsorbent material into structured beds for rapid pressure swing adsorption (PSA) cycles with low pressure drop, fast mass transfer, and low attrition, (3) cycle development studies to optimize the PSA process, and (4) develop simulation tools for rapid cycle modeling and numerical evaluation/optimization.

20 FOSSIL-FUELED POWER PLANTS↗

Quantitative Characterization of Nanostructured Materials

The two-and-a-half day symposium on the "Quantitative Characterization of Nanostructured Materials" will be the first comprehensive meeting on this topic held under the auspices of a major U.S. professional society. Spring MRS Meetings provide a natural venue for this symposium as they attract a broad audience of researchers that represents a cross-section of the state-of-the-art regarding synthesis, structure-property relations, and applications of nanostructured materials. Close interactions among the experts in local structure measurements and materials researchers will help both to identify measurement needs pertinent to real-world materials problems and to familiarize the materials research community with the state-of-the-art local structure measurement techniques. We have chosen invited speakers that reflect the multidisciplinary and international nature of this topic and the need to continually nurture productive interfaces among university, government and industrial laboratories. The intent of the symposium is to provide an interdisciplinary forum for discussion and exchange of ideas on the recent progress in quantitative characterization of structural order in nanomaterials using different experimental techniques and theory. The symposium is expected to facilitate discussions on optimal approaches for determining atomic structure at the nanoscale using combined inputs from multiple measurement techniques.

36 MATERIALS SCIENCE↗

Two-dimensional spin systems in PECVD-grown diamond with tunable density and long coherence for enhanced quantum sensing and simulation

Systems of spins engineered with tunable density and reduced dimensionality enable a number of advancements in quantum sensing and simulation. Defects in diamond, such as nitrogen-vacancy (NV) centers and substitutional nitrogen (P1 centers), are particularly promising solid-state platforms to explore. However, the ability to controllably create coherent, two-dimensional spin systems and characterize their properties, such as density, depth confinement, and coherence, is an outstanding materials challenge. We present a refined approach to engineer dense (≳1 ppm ∙ nm), 2D nitrogen, and NV layers in diamond using delta-doping during plasma-enhanced chemical vapor deposition epitaxial growth. We employ both traditional materials techniques, e.g., secondary ion mass spectrometry, alongside NV spin decoherence-based measurements to characterize the density and dimensionality of the P1 and NV layers. We find P1 densities of 5–10 ppm ∙ nm, NV densities between 1 and 3.5 ppm ∙ nm tuned via electron irradiation dosage, and depth confinement of the spin layer down to 1.6 nm. We also observe high (up to 0.74) ratios of NV to P1 centers and reproducibly long NV coherence times, dominated by dipolar interactions with the engineered P1 and NV spin baths.

36 MATERIALS SCIENCE↗

Development of processing techniques for advanced thermal protection materials

The main purpose of this work has been in the development and characterization of materials for high temperature applications. Thermal Protection Systems (TPS) are constantly being tested, and evaluated for increased thermal shock resistance, high temperature dimensional stability, and tolerance to environmental effects. Materials development was carried out through the use of many different instruments and methods, ranging from extensive elemental analysis to physical attributes testing. The six main focus areas include: (1) protective coatings for carbon/carbon composites; (2) TPS material characterization; (3) improved waterproofing for TPS; (4) modified ceramic insulation for bone implants; (5) improved durability ceramic insulation blankets; and (6) ultra-high temperature ceramics. This report describes the progress made in these research areas during this contract period.

Selvaduray, Guna S.↗

Ballistic-Electron-Emission Microscopy Techniques for Nanometer-scale Characterization of Interfaces

Semiconductor interface properties are among the most important phenomena in materials science and technology. The study of metal/semiconductor Schottky barrier interfaces has been the primary focus of a large research and development community for decades. Throughout the long history of interface investigation, the study of interface defect electronic properties have been seriously hindered by the fundamental experimental difficulty of probing subsurface structures. A new method, Ballistic-Electron-Emission Microscopy (BEEM), has been developed which not only enables spectroscopic probing of subsurface interface properties, but also, provides nanometer-resolution imaging capabilities. BEEM employs Scanning Tunneling Microscopy (STM) and a unique spatially localized ballistic electron spectroscopy method...

Bell, L. D.↗

Evaluation of Ultrasonic and Thermal Nondestructive Evaluation for the Characterization of Aging Degradation in Braided Composite Materials

This paper examines the ability of traditional nondestructive evaluation (NDE) techniques to measure the degradation of braided polymer composite materials subjected to thermal-humidity cycling to simulate aging. A series of braided composite coupons were examined using immersion ultrasonic and pulsed thermography techniques in the as received condition. These same specimens were then examined following extended thermal-humidity cycling. Results of this examination did not show a significant change in the resulting (NDE) signals.

Martin, Richard E.↗

Combinatorial Discovery of Lanthanum–Tantalum Oxynitride Solar Light Absorbers with Dilute Nitrogen for Solar Fuel Applications

© 2017 American Chemical Society. Oxynitrides with the photoelectrochemical stability of oxides and desirable band energetics of nitrides comprise a promising class of materials for solar photochemistry. Challenges in synthesizing a wide variety of oxynitride materials has limited exploration of this class of functional materials, which we address using a reactive cosputtering combined with rapid thermal processing method to synthesize multi-cation-multi-anion libraries. We demonstrate the synthesis of a LaxTa1-xOyNzthin film composition spread library and its characterization by both traditional thin film materials characterization and custom combinatorial optical spectroscopy and X-ray absorption near edge spectroscopy (XANES) techniques, ultimately establishing structure-chemistry-property relationships. We observe that over a substantial La-Ta composition range the thin films crystallize in the same perovskite LaTaON2structure with significant variation of anion chemistry. The relative invariance in optical band gap demonstrates a remarkable decoupling of composition and band energetics so that the composition can be optimized while retaining the desirable 2 eV band gap energy. We also demonstrate the intercalation of diatomic nitrogen into the La3TaO7structure, which gives rise to a direct-allowed optical transition at 2.2 eV, less than half the value of the oxide's band gap. These findings motivate further exploration of the visible light response of this material that is predicted to be stable over a wide range of electrochemical potential.

Suram, Santosh K.↗

Characterization of Rare Earth Element Minerals in Coal Utilization Byproducts

The United States currently produces over 100 million tons of coal utilization byproducts (CUB) per year in the form of fly ash, bottom ash, slag, and flue gas (American Coal Ash Association (ACCA), 2015). But this “waste material” also contains potentially useful levels of rare earth elements (REE). Rare earth elements are crucial for many existing and emerging technologies, but the U.S. lacks a domestic, sustainable REE source. Our project explored the possibility of developing a supply of REEs for U.S. technologies by extracting REEs from CUBs. This work offers the potential to reduce our dependence on other countries for supply of these critical elements (NETL, REE 2016 Project Portfolio). Geologic and diagenetic history, industrial preparation methods, and the specific combustion process all play major roles in the composition of CUB. During combustion, inorganic mineral phases of coal particles are fluidized at temperatures higher than 1400oC, so inorganic mineral materials are oxidized, fused, disintegrated, or agglomerated into larger spherical and amorphous (non-crystalline) particles. The original mineralogy of the coal-containing rock and heating/cooling of the material significantly affects the composition and morphology of the particles in the combustion byproduct (Kutchko and Kim, 2006). Thus, different types of coal/refuse/ash must be characterized to better understand mineral evolution during the combustion process. Our research focused on developing a working model to address how REE minerals behave during the combustion process: this research should help determine the most effective engineering methods for extracting REEs from CUBs. We used multimodal imaging and image processing techniques to characterize six rock and ash samples from different coal power plants with respect to morphology, grain size, presence of mineral phases, and elemental composition. The results of these characterization activities provided thresholds for realizing the occurrence of REE mineral phases in CUB and allowed us to calculate structural and volumetric estimates of REE. Collectively, the rock and coal ash samples contained minerals such as quartz, kaolinite, muscovite/illite, iron oxide (as hematite or magnetite), mullite, and clinochlore. Trace minerals included pyrite, zircon, siderite, rutile, diopside, foresterite, gypsum, and barite. We identified REE phosphate minerals monazite (Ce,La,Nd,Th)(PO 4 ,SiO 4 ), xenotime (YPO 4 ,SiO 4 ), and apatite (Ca 5 (PO 4 ) 3 (F,Cl,OH) via SEM and electron microprobe analysis: these materials generally occurred as 1-10 μm-long crystals in the rock and ash samples. As has been shown in other studies, amorphous material-aluminosilicate glass or iron oxyhydroxide-are the major components of coal fly and bottom ash. Trace amounts of amorphous calcium oxide and mixed element (e.g., Al-Si-Ca-Fe) slag are also present. Quartz, mullite, hematite, and magnetite are the crystalline phases present. We found that REEs are present as monomineralic grains dispersed within the ash, as well as fused to or encapsulated by amorphous aluminosilicate glass particles. Monazite and xenotime have relatively high melting points (>1800 °C) compared to typical combustion temperatures; our observations indicate that the REE-phosphates, which presumably contribute a large percentage of REE to the bulk ash REE pool, as measured by mass spectroscopy, are largely unaltered by the combustion. Our study shows that conventional coal combustion processes sequester REE minerals into aluminosilicate glass phases, which presents a new engineering challenge for extracting REE from coal ash. The characterization work summarized in this report provides a semi-quantitative assessments of REE in coal-containing rock and CUB. The data we obtained from 2- and 3-D imaging, elemental mapping, volumetric estimates, and advanced high-resolution pixel classification successfully identified the different mineral phases present in CUB. Further, our characterization results can guide techniques for extracting REEs from CUB, or other geologic and engineered materials. Whilst, interpretations will inform future REE separation and extraction techniques and technologies practical for commercial utilization of combustion byproducts generated by power plants.

01 COAL, LIGNITE, AND PEAT↗

Experimentally determined spectral optimization for dedicated breast computed tomography

Purpose: The current study aimed to experimentally identify the optimal technique factors (x-ray tube potential and added filtration material/thickness) to maximize soft-tissue contrast, microcalcification contrast, and iodine contrast enhancement using cadaveric breast specimens imaged with dedicated breast computed tomography (bCT). Secondarily, the study aimed to evaluate the accuracy of phantom materials as tissue surrogates and to characterize the change in accuracy with varying bCT technique factors. Methods: A cadaveric breast specimen was acquired under appropriate approval and scanned using a prototype bCT scanner. Inserted into the specimen were cylindrical inserts of polyethylene, water, iodine contrast medium (iodixanol, 2.5 mg/ml), and calcium hydroxyapatite (100 mg/ml). Six x-ray tube potentials (50, 60, 70, 80, 90, and 100 kVp) and three different filters (0.2 mm Cu, 1.5 mm Al, and 0.2 mm Sn) were tested. For each set of technique factors, the intensity (linear attenuation coefficient) and noise were measured within six regions of interest (ROIs): Glandular tissue, adipose tissue, polyethylene, water, iodine contrast medium, and calcium hydroxyapatite. Dose-normalized contrast to noise ratio (CNRD) was measured for pairwise comparisons among the six ROIs. Regression models were used to estimate the effect of tube potential and added filtration on intensity, noise, and CNRD. Results: Iodine contrast enhancement was maximized using 60 kVp and 0.2 mm Cu. Microcalcification contrast and soft-tissue contrast were maximized at 60 kVp. The 0.2 mm Cu filter achieved significantly higher CNRD for iodine contrast enhancement than the other two filters (p=0.01), but microcalcification contrast and soft-tissue contrast were similar using the copper and aluminum filters. The average percent difference in linear attenuation coefficient, across all tube potentials, for polyethylene versus adipose tissue was 1.8%, 1.7%, and 1.3% for 0.2 mm Cu, 1.5 mm Al, and 0.2 mm Sn, respectively. For water versus glandular tissue, the average percent difference was 2.7%, 3.9%, and 4.2% for the three filter types. Conclusions: Contrast-enhanced bCT, using injected iodine contrast medium, may be optimized for maximum contrast of enhancing lesions at 60 kVp with 0.2 mm Cu filtration. Soft-tissue contrast and microcalcification contrast may also benefit from lower tube potentials (60 kVp). The linear attenuation coefficients of water and polyethylene slightly overestimate the values of their corresponding tissues, but the reported differences may serve as guidance for dosimetry and quality assurance using tissue equivalent phantoms.

60 APPLIED LIFE SCIENCES↗

A color-tunable luminescent material with functionalized graphitic carbon nitride as multifunctional supports

A color-tunable luminescent material was prepared based on the composition of functionalized graphitic carbon nitride (g-C{sub 3}N{sub 4}) and europium (III). The functionalized g-C{sub 3}N{sub 4} layers not only behave as multifunctional supports including ligand coordinated with europium (III) and a support structure for the formation of the luminescent material, but exhibit excitation wavelength-dependent luminescence, thus the energy transfer between the functionalized g-C{sub 3}N{sub 4} and europium (III) can match very well by controlling the emission wavelength of functionalized g-C{sub 3}N{sub 4}. The as-prepared materials was comprehensively characterized via X-ray photoelectron spectroscopy, Fourier Transform Infrared spectroscopy, X-ray scattering techniques, Ultraviolet and Visible spectrophotometer, fluorescence spectrophotometer, thermogravimetric analysis, etc. The luminescent material exhibits multi-color emissions which are consistent with the characteristic emissions of europium (III) and functionalized g-C{sub 3}N{sub 4}, and the photoluminescence quality and density of the europium (III) can be greatly enhanced. The brilliant optical properties of the materials make them suiting for multipurpose applications in practical fields. - Graphical abstract: Schematic illustration of the synthesis and basic composition of the luminescent material. Inset figures were luminescence emission spectra of g-C{sub 3}N{sub 4} (A), europium (III) complex (a) and luminescent material (b) with the same concentration in (B) (K{sub ex}=350 nm) and photographs of (left) H{sub 2}O and (right) the H{sub 2}O dispersion of luminescence emission spectra under 350 nm UV radiation. The energy transfer in the luminescent material matchs very well and it exhibits multi-color emissions simultaneously. The enhanced photoluminescence quality and density of the europium (III) makes them suiting for multipurpose applications in practical fields. - Highlights: • Luminescent material exhibits multi-color emissions when excited by single wavelength. • The energy trsnsfer between functionalized g-C{sub 3}N{sub 4} and europium matches very vell. • Functionalized g-C{sub 3}N{sub 4} exhibits excitation wavelength-depengdent bright blue luminescence. • Functionalized g-C{sub 3}N{sub 4} layer provided as multifunctional supports.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of mechanical discontinuities based on data-driven classification of compressional-wave travel times

Wave propagation and diffusive transport phenomena are influenced by the mechanical discontinuities in material. Here this study shows that certain bulk properties of the network of low-velocity mechanical discontinuities (e.g. air-filled cracks) in a material can be characterized by processing compressional-wave travel times using traditional data-driven classification techniques. To that end, we perform three tasks in chronological order: (1) use the discrete fracture network (DFN) method to create two-dimensional (2D) numerical models of crack-bearing material embedded with various types of low-velocity mechanical discontinuities, (2) use the fast marching method (FMM) to simulate the propagation of the wave/diffusion front from a single source through the 2D crack-bearing material to multiple receivers placed on the boundary of the material, and (3) train 9 data-driven classifiers to characterize the crack-bearing materials (i.e. bulk properties of the network of mechanical discontinuities in the crack-bearing material) by learning from the simulations of travel times detected by multiple receivers placed around the crack-bearing material. The classifiers identified the orientation, spatial distribution, and dispersion of the low-velocity mechanical discontinuities. Voting classifier performs the best among the 9 classifiers. For the characterization of bulk dispersion and distribution of discontinuities, the sensors located on the adjacent boundaries are more important; whereas for the characterization of bulk orientation of discontinuities, the sensors located on the opposite side are more important.

42 ENGINEERING↗

Cornell Fuel Cell Institute: Materials Discovery to Enable Fuel Cell Technologies (Final Report)

The discovery and understanding of new, improved materials to advance fuel cell technology are the objectives of the Cornell Fuel Cell Institute (CFCI) research program. CFCI was initially formed in 2003. This report highlights the accomplishments from 2006-2009. Many of the grand challenges in energy science and technology are based on the need for materials with greatly improved or even revolutionary properties and performance. This is certainly true for fuel cells, which have the promise of being highly efficient in the conversion of chemical energy to electrical energy. Fuel cells offer the possibility of efficiencies perhaps up to 90 % based on the free energy of reaction. Here, the challenges are clearly in the materials used to construct the heart of the fuel cell: the membrane electrode assembly (MEA). The MEA consists of two electrodes separated by an ionically conducting membrane. Each electrode is a nanocomposite of electronically conducting catalyst support, ionic conductor and open porosity, that together form three percolation networks that must connect to each catalyst nanoparticle; otherwise the catalyst is inactive. This report highlights the findings of the three years completing the CFCI funding, and incudes developments in materials for electrocatalyts, catalyst supports, materials with structured and functional porosity for electrodes, and novel electrolyte membranes. The report also discusses developments at understanding electrocatalytic mechanisms, especially on novel catalyst surfaces, plus in situ characterization techniques and contributions from theory. Much of the research of the CFCI continues within the Energy Materials Center at Cornell (emc 2 ), a DOE funded, Office of Science Energy Frontier Research Center (EFRC).

08 HYDROGEN↗

Technical Note: Radiological properties of tissue surrogates used in a multimodality deformable pelvic phantom for MR-guided radiotherapy

Purpose: Phantom surrogates were developed to allow multimodal [computed tomography (CT), magnetic resonance imaging (MRI), and teletherapy] and anthropomorphic tissue simulation as well as materials and methods to construct deformable organ shapes and anthropomorphic bone models. Methods: Agarose gels of variable concentrations and loadings were investigated to simulate various soft tissue types. Oils, fats, and Vaseline were investigated as surrogates for adipose tissue and bone marrow. Anthropomorphic shapes of bone and organs were realized using 3D-printing techniques based on segmentations of patient CT-scans. All materials were characterized in dual energy CT and MRI to adapt CT numbers, electron density, effective atomic number, as well as T1- and T2-relaxation times to patient and literature values. Results: Soft tissue simulation could be achieved with agarose gels in combination with a gadolinium-based contrast agent and NaF to simulate muscle, prostate, and tumor tissues. Vegetable oils were shown to be a good representation for adipose tissue in all modalities. Inner bone was realized using a mixture of Vaseline and K{sub 2}HPO{sub 4}, resulting in both a fatty bone marrow signal in MRI and inhomogeneous areas of low and high attenuation in CT. The high attenuation of outer bone was additionally adapted by applying gypsum bandages to the 3D-printed hollow bone case with values up to 1200 HU. Deformable hollow organs were manufactured using silicone. Signal loss in the MR images based on the conductivity of the gels needs to be further investigated. Conclusions: The presented surrogates and techniques allow the customized construction of multimodality, anthropomorphic, and deformable phantoms as exemplarily shown for a pelvic phantom, which is intended to study adaptive treatment scenarios in MR-guided radiation therapy.

61 RADIATION PROTECTION AND DOSIMETRY↗

Microscale Isotopic Variation in Uranium Fuel Pellets with Implications for Nuclear Forensics

Until recently, the analysis and identification of nuclear fuel pellets in the context of a nuclear forensics investigation have been mainly focused on macroscopic characteristics, such as fuel pellet dimensions, uranium enrichment, and other reactor-specific features. Here, we report microscale isotopic heterogeneity observed in different fuel pellet fragments that were characterized in situ by nanoscale secondary ion mass spectrometry (NanoSIMS). The materials analyzed include fuel fragments obtained as part of the Collaborative Materials Exercise (CMX-4) organized by the Nuclear Forensics International Technical Working Group (ITWG), as well as a fuel pellet fragment from a commercial power reactor. Although the commercial fuel pellet showed a homogeneous 235 U/ 238 U ratio across the sample (within analytical error), NanoSIMS imaging of the CMX-4 fuel pellet fragments showed distinct microscale variations in the uranium isotopic composition. The average 235 U enrichments were 2.2 and 2.9% for the two samples; however, the measured 235 U/ 238 U ratios varied between 0.0081 and 0.035 (0.79–3.3 atom % 235 U) and between 0.0090 and 0.045 (0.89–4.3 atom % 235 U). The measurement of 236 U in one of the CMX-4 samples suggested the use of at least three uranium oxide powders of different isotopic compositions (“source terms”) in the production of the pellets. These variations were not detected using the conventional bulk, macroscopic techniques applied to these materials. Furthermore, our study highlights the importance of characterizing samples on the microscale for heterogeneities that would otherwise be overlooked and demonstrates the potential use of NanoSIMS in guiding further nuclear forensic analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In situ and operando force-based atomic force microscopy for probing local functionality in energy storage materials

Electrochemical energy storage is the key enabling component of electric vehicles and solar-/wind-based energy technologies. The enhancement of energy stored requires the detailed understanding of charge storage mechanisms and local electrochemical and electromechanical phenomena over a variety of length scales from atoms to full cells. Classical electrochemical techniques, such as voltammetry, represent the macroscopic electrochemical properties, and consequently do not allow to extract important information about local electrochemical reactions, ions adsorption, intercalations, and transport. Understanding, controlling, and tuning the local electrochemical functionalities in functional energy materials require in situ/operando techniques which limit the use of structural and functional characterization techniques that provide local information. Here, force-based atomic force microscopies (AFMs) have provided novel insights into locally probing electrochemical mechanisms on tens of nanometer and even molecular length scales and provide a viable pathway to probe electrochemical processes in situ/operando. In this review, we highlight the contributions in the development and application of force-based AFM methods to elucidate the local charge storage mechanism in a variety of energy-related materials. We will focus in particular on methods or AFM modalities in a liquid electrolyte environment.

25 ENERGY STORAGE↗