Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MARTENSITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

Fundamental Understanding of Creep-Fatigue Interactions in 9Cr-1MoV Steel Welds. Final Report

Ferritic-martensitic steels constitute a vital class of materials for current and future generation of nuclear reactors as well as ultra supercritical coal fired power plants due to their superior creep resistant properties. One particular ferritic-martensitic steel, 9Cr-1MoV (Grade 91) is one of five materials approved for high temperature use in nuclear service by the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC). Grade 91 is also a candidate material for proposed fission and fusion reactors such as the sodium cooled fast reactor (SFR). In service, Grade 91 components can be subjected to elevated temperatures and cyclic stresses, leading to the accumulation of creep-fatigue (CF) damage. While the monotonic creep properties of Grade 91 steels have been studied extensively, there is less knowledge concerning the mechanisms governing CF damage of this steel in the creep-dominated failure region. Moreover, the creep failure is especially pronounced in welded Grade 91 components, which are commonly joined using conventional arc welding techniques such as flux-cored arc welding (FCAW). In a Grade 91 weld, the creep failure typically occurs in the outer region of the heat affected zone (HAZ), specifically in the intercritical or fine-grained heat-affected zone (ICHAZ or FGHAZ), a phenomenon known as type IV failure. Currently, there exists a limited knowledge of CF damage mechanisms in Grade 91 welds. Improving the mechanistic understanding of the CF damage and failure of Grade 91 steel and its welds with inhomogeneous microstructure is crucial for the safety and design of key structural components in advanced, high-temperature reactors. The overall objectives of the project were to advance the state of knowledge and understanding of CF damage in both Grade 91 base metal and its welds, especially under loading conditions where creep is the dominant damage mechanism. Uncovering the mechanisms governing the creep-fatigue deformation and damage in Grade 91 base metal in creep-dominated region as well as type IV failure in Grade 91 welds contributes to a new knowledge that may lead to more accurate life prediction models than those currently in use. Moreover, the superior CF properties obtained by low heat input welding has a high potential to develop practical solutions to the premature failure of Grade 91 weld.

36 MATERIALS SCIENCE↗

Microstructural Characterization of High Dose Irradiated HT9

The present report provides a short summary of the recent efforts to irradiate various HT9 heats and compositions to a high damage level (>500 peak dpa) and characterize the changes to the microstructure. The majority of the data reported here will focus on characterizing the “INL” HT9 heat. This particular heat was chosen due to its high volume fraction of tempered martensite (>90%) in the microstructure. The results show that very little swelling is present in INL HT9 up to doses up to 600 peak dpa. Voids are only observed in the near surface region. Some carbides are also observed to accompany the irradiation. Comparison of void swelling with published neutron irradiation shows good agreement. Additional investigations into the response of delta ferrite grains show a very different distribution of voids and significantly higher void swelling compared to the tempered martensite grains.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

EVPSC modeling of 316 stainless steel with and without observed phase transformation

The following is a description of modeling the constitutive behavior of the transforming and non-transforming 316 stainless steel measured in-situ at APS. Details of the elasto-viscoplastic self-consistent (EVPSC) polycrystal deformation model are described in the literature and only the salient information is given here. The EVPSC model is a general rate-sensitive self-consistent polycrystal plasticity model valid at arbitrary large deformations. The homogenizing method used is the self-consistent approach, originally proposed by Kröner, assuming that each grain is an ellipsoidal inclusion embedded in an infinite homogeneous equivalent medium (HEM), where the interaction is determined using Eshelby's solution. The hardening behavior is described by a Voce type strain hardening law, and the phase transformation uses a strain energy criterion for choosing a single daughter grain for each parent grain that reaches a critical value of the Von Mises equivalent strain. The orientation relationship between parent and daughter grains is determined based upon a rotation matrix that preserves an invariant line between the parent and daughter. The evolution law for the growth of the martensite phase is based on an empirical accumulated shear strain law proposed by Olson and Cohen. The single crystal elastic constants for the austenite phase are as reported for 316 stainless steel and the single crystal elastic constants of the martensite are taken from hardened SAE 1050 plain-carbon steel.

36 MATERIALS SCIENCE↗

Report on partially complete post-irradiation-examination of the INL samples

Ferritic-martensitic steels (NF616 and T91), and austenitic stainless steel 800H and its Grain Boundary Engineering (GBE)-treated version 800H-TMP (ThermoMechanical Processing) were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) and their microstructures and mechanical properties were characterized. Ferritic-martensitic steels were irradiated up to 8.16 dpa in the irradiation temperatures ranging from 241 °C to 447.5 °C. Selected 800H and 800H-TMP samples were also irradiated up to 9.12 dpa at 359°C to 431°C. Vickers hardness measurement, fractography, and microstructural characterization were performed on the selected samples in the LAMDA lab. Radiation-induced hardening of NF616 and T91 was observed in the hardness measurements which show ~37% to ~65% increases, depending on irradiation dose and irradiation temperature. Within the irradiation conditions studied in this work, samples with a higher dose had a higher hardness. All the tested alloy 800H and 800H-TMP in this work showed irradiation-hardening by ~96±7% to ~152±10%. Alloy 800HTMP tended to have slightly smaller irradiation-hardening than alloy 800H. The fractography of NF616 samples D2 (2.96 dpa at 291.5°C), D4 (5.91 dpa at 359°C), and D6 (8.16 dpa at 431°C) indicated loss of ductility with negligible necking for the sample D2, yet obvious ductile failure for samples D4 and D6. Fractography of alloy 800H samples N4 (7.27 dpa at 359°C), N5 (3.9 dpa at 451.5°C), and N6 (9.01 dpa at 431°C), and alloy 800H-TMP samples P4 (7.36 dpa at 359°C), P5 (3.95 dpa at 451.5°C), and P6 (9.12 dpa at 431°C) indicated that all samples failed in a ductile mode, with obvious necking. Dimples were observed where large Ti-containing particles were observed for the samples. TEM characterization was performed on alloy 800H (N4, N5, N6) and 800H-TMP (P4, P5 and P6). Accumulation of M23C6 precipitates at grain boundaries was observed in all samples, and the presence of Ti(C,N) precipitates at grain boundaries and in the matrix was observed in alloy 800H-TMP. M23C6 precipitates were found to have the cube-on-cube orientation relationship with the matrix. In addition, nanoscale Si-rich clusters were observed in the matrix of all samples. Atom probe tomography was conducted on the same samples, and their results are being analyzed to be integrated with the TEM results for a confident description of the clustering behavior. Due to the low irradiation temperature (up to 451.5°C), dislocation loops formed in all samples, with the density and the average size of dislocation loops in the order of 1022 – 1023 m-3 and 11.7 – 15.9 nm, respectively. The loop densities in alloy 800H were higher than that in alloy 800H-TMP under the same irradiation conditions. Further systematic data analyses, together with some complementary experiments, will be pursued for these samples to foster peer-reviewed journal article publications.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Post-Irradiation-Examination of the ORNL and LANL Samples

Ferritic-martensitic steel G92-2b (an optimized Grade 92 heat) and austenitic stainless steel 800H and its Grain Boundary Engineering (GBE)-treated version 800H-TMP (ThermoMechanical Processing) were irradiated in the HFIR. Ferritic-martensitic steel T91 was irradiated in the ATR. Selected G92-2b samples were irradiated up to 14.66 dpa at two temperature ranges: 400–496.7°C and 683.3–720°C. Selected 800H and 800H-TMP samples were irradiated to 1.28 dpa at 580°C. A selected T91 sample was irradiated to 6.5 dpa at 295°C. Vickers hardness measurements, fractography, and microstructural characterization were performed on the selected samples in LAMDA. Further systematic data analyses, together with some complementary experiments, will be pursued for these samples to foster peer-reviewed journal article publications.

36 MATERIALS SCIENCE↗

Development of Creep-Fatigue Design Methodology for Base Metal and Weldments of G91

This report provides an update on research activity at the Argonne National Laboratory (ANL) in the area of high temperature materials design methodology for advanced ferritic-martensitic steels for advanced Small Module Reactor (aSMR) Concepts. This is a Level 2 report delivered in FY15 (M2AT-15AN1602013) under the work package AT-15AN160201 “Materials Design Technology for Advanced SMR Concepts” performed by ANL for the Department of Energy, Office of Nuclear Energy. The overall objective of the Materials for Advanced SMR Concepts is to address key long-term design needs for applications of advanced materials. Advanced materials are a critical element in the development of advanced SMR concepts. High temperature materials design technology must be developed to realize the benefits of advanced materials in advanced reactor designs. Among a number of technical issues relevant to materials performance criteria and high temperature design methodology, creep, creep-fatigue, weldment design methodologies, and long-term thermal aging effects are of the highest priority. The effort in this project has focused on improvement of current ASME creep-fatigue design rules and development of a mechanism-based creep-fatigue design method for ferritic-martensitic steels, G91 and G92. This report presents the development of a fundamentally new creep-fatigue life model for G91 base metal and improvements of understanding of creep-fatigue interactions and creep-fatigue design rules for G91 weldments.

36 MATERIALS SCIENCE↗

Investigating the Role of Defects in α-Pu Phase Transitions using Density Functional Theory

Before reaching its relatively low melting point of 913 K, plutonium undergoes six solid state phases: simple monoclinic alpha, body-centered monoclinic beta, face-centered orthorhombic gamma, face centered cubic delta, body-centered tetragonal delta-prime, and body-centered cubic epsilon phases. Due to their low symmetry, the monoclinic alpha and beta phases have not been studied extensively, however it has been previously hypothesized that the transition between alpha and beta is caused by defects in the lattices due to the incommensurate number of atoms. Additionally, the martensitic delta to alpha phase transformation in plutonium-gallium alloys induces an expanded alpha lattice known as alpha prime, most likely due to the insoluble gallium impurity atom. This work explores how defects such as plutonium interstitials and gallium interstitials and substitutionals may affect the alpha plutonium lattice, providing a better understanding of the mechanisms for the alpha-beta and martensitic phase transformations through density functional theory (DFT). Results indicate that plutonium interstitials within the alpha lattice induce beta features structurally and electronically, such as volume expansion and bonding changes, and gallium interstitials and substitutionals within the alpha lattice induce volume changes as observed experimentally in alpha prime.

36 MATERIALS SCIENCE↗

The Toughness of High-Strength Steel Weld Metals

Low-temperature phase transformation (LTPT) welding consumables are a new class of welding wires developed to mitigate hydrogen-induced cracking in the welding of high-strength steels without preheating or postweld heat treatment. LTPT weld metals have a high strength, but their toughness needs further investigation. LTPT weld metals predominately contain a martensite microstructure, which is necessary to achieve high strength; however, martensitic weld metals containing oxide inclusions have relatively poor toughness. For this study, three welding processes — gas metal arc welding (GMAW), gas tungsten arc welding (GTAW), and hot wire GTAW — were investigated. Optical microscopy, scanning electron microscopes, and transmission electron microscopes were employed for characterization. The role of the shielding gas in the formation of oxide inclusions in LTPT weld metals was investigated. The formation of oxide inclusions in the weld metals was related to the CO 2 in the shielding gas. When 100% Ar or a pure inert shielding gas mixture was used for all three welding processes, oxide inclusions were greatly reduced, and the weld metal toughness improved considerably, matching the base metal toughness. The mechanism by which inclusions promote fracture propagation in the weld metal was proposed.

36 MATERIALS SCIENCE↗

Tempering and Austempering of Double Soaked Medium Manganese Steels

The addition of a tempering or austempering step to the double soaking of a 0.14C–7.17Mn (wt pct) steel was investigated in the present contribution. The double soaking heat treatment is a two-step intercritical annealing heat treatment, which generates microstructures of athermal martensite, retained austenite and ferrite when applied to medium manganese steels. Microstructures following double soaking and (aus)tempering contained a combination of retained austenite, athermal or tempered martensite, and blocky or bainitic ferrite. X-ray diffraction, dilatometry and transmission Kikuchi diffraction were utilized to investigate microstructural changes which occurred during tempering or austempering. The resulting mechanical properties were measured using uniaxial tensile testing. The double soaking plus tempering heat treatment was shown to generate an ultimate tensile strength of 1,340 MPa in combination with 28 pct total elongation while the double soaking plus austempering heat treatment resulted in an ultimate tensile strength of 1,675 MPa and total elongation of 22 pct. Overall, both novel heat treatments produced a combination of strength and ductility desired for the third generation of advanced high strength steels.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Intercritically Treated Grade 91 Steel

Premature creep failures at the intercritical heat affected zone (ICHAZ) of creep-resistant steel weldments have been frequently reported. However, the creep degradation mechanism of different microstructure constituents in ICHAZ is complicated and needs further clarification. In this work, Grade 91 steel was intercritically heat-treated at a temperature (860 °C) between the critical temperatures AC1 and AC3, and a correlation between microstructure and mechanical properties of the heat-treated specimen was built. The effects of austenitization and tempering resulting from the intercritical treatment (IT) differentiated the local strain energies between the two microstructure constituents: newly transformed martensite (NTM) and over-tempered martensite (OTM). The formation of NTM grains led to a hardness increase from 247 HV0.5 in the base metal to 332 HV0.5 in the IT specimen. The ultimate tensile strength (UTS) increased from 739 MPa in the base metal to 1054 MPa in the IT specimen. Extensive growth of the OTM grains and rapid recovery of NTM grains took place simultaneously in the IT specimen during a typical tempering at 760 °C. These microstructure degradations led to a lowered hardness of 178 HV0.5, a reduced UTS of 596 MPa, and a poor creep resistance with a minimum creep strain rate of 0.49 %/h at 650 °C in an IT + tempering (ITT) specimen.

36 MATERIALS SCIENCE↗

Transient Microstructure Evolutions and Local Properties of Dual-Phase 980 MPa Grade Steel Via Friction Stir Spot Processing

Friction stir processing is a novel solid-state process to modify microstructures and their properties by intense, localized plastic deformation. However, little research has been reported for microstructure evolutions of advanced high-strength steels during the process. The present work focuses on the study of transient microstructure changes and local mechanical properties for friction stir spot processed dual-phase (DP) 980 MPa grade steel (DP980) under different peak temperatures. A pinless silicon nitride ceramic tool was used to produce relatively simple material deformation and flow near the tool. Friction stir spot processed steel samples were characterized by optical and electron microscopies. Furthermore, Vickers microhardness and nano-indentation measurements were used to study local mechanical properties for correlation with microstructures. A swallow layer of refined grains (<0.6 µm) was obtained with a low peak temperature (under 400 °C), whereas higher peak temperatures (>Ac 1 ) led to a change in grain size with different microstructures (fine-grained DP or martensite). Electron back-scattered diffraction characterizations revealed a large deformation in the as-received microstructures (mixture of ferrite and tempered martensite) induced by friction stir spot processing, leading to recrystallization and grain refinement around the stirred zone. Also, nano-indentation measurements showed a higher hardness than the hardness of the as-received DP980. Friction stir processing with different process conditions effectively changed microstructures and local mechanical properties.

36 MATERIALS SCIENCE↗

Effects of Intercritical Annealing Temperature on Mechanical Properties of Fe-7.9Mn-0.14Si-0.05Al-0.07C Steel

A medium Mn steel has been designed to achieve an excellent combination of strength and ductility based on the TRIP (Transformation Induced Plasticity) concept for automotive applications. Following six passes of hot rolling at 850 °C, the Fe-7.9Mn-0.14Si-0.05Al-0.07C (wt.%) steel was warm-rolled at 630 °C for seven passes and subsequently air cooled to room temperature. The sample was subsequently intercritically annealed at various temperatures for 30 min to promote the reverse transformation of martensite into austenite. The obtained results show that the highest volume fraction of austenite is 39% for the sample annealed at 600 °C. This specimen exhibits a yield stress of 910 MPa and a high ultimate tensile stress of 1600 MPa, with an elongation-to-failure of 0.29 at a strain rate of 1 × 10⁻³/s. The enhanced work-hardening ability of the investigated steel is closely related to martensitic transformation and the interaction of dislocations. Especially, the alternate arrangement of acicular ferrite (soft phase) and ultrafine austenite lamellae (50–200 nm, strong and ductile phase) is the key factor contributing to the excellent combination of strength and ductility. On the other hand, the as-warm-rolled sample also exhibits the excellent combination of strength and ductility, with elongation-to-failure much higher than those annealed at temperatures above 630 °C.

36 MATERIALS SCIENCE↗

Large Inverse Magnetocaloric Effects and Giant Magnetoresistance in Ni-Mn-Cr-Sn Heusler Alloys

The magnetostructural transitions, magnetocaloric effects, and magnetoresistance properties of Ni45Mn43CrSn11 Heusler alloys were investigated using X-ray diffraction (XRD), field-dependent magnetization, and electrical resistivity measurements. A large inverse and direct magnetocaloric effect has been observed in Ni45Mn43CrSn11 across the martensitic and Curie transition temperature, respectively. The values of the latent heat (L = 15.5 J/g) and corresponding magnetic (ΔSM) and total (∆ST) entropy changes (ΔSM = 35 J/kg·K for ΔH = 5T and ∆ST = 39.7 J/kg·K) have been evaluated using magnetic and differential scanning calorimetry (DSC) measurements, respectively. A substantial jump in resistivity was observed across the martensitic transformation. A large negative magnetoresistance (~67%) was obtained at the magnetostructural transition for a field change of 5 T. The roles of the magnetic and structural changes on the transition temperatures and the potential application of Ni45Mn43CrSn11 Heusler alloys for refrigerator technology are discussed.

Pandey, Sudip↗

Dissimilar Materials Joining of Carbon Fiber Polymer to Dual Phase 980 by Friction Bit Joining, Adhesive Bonding, and Weldbonding

In the present study, joining of a carbon fiber-reinforced polymer and dual phase 980 steel was studied using the friction bit joining, adhesive bonding, and weldbonding processes. The friction bit joining process was optimized for the maximum joint strength by varying the process parameters. Then, the adhesive bonding and weld bonding (friction bit joining plus adhesive bonding) processes were further developed. Lap shear tensile and cross-tension testing were used to assess the joint integrity of each process. Fractured specimens were compared for the individual processes. The microstructures in the joining bit ranged from tempered martensite to fully martensite in the cross-section view of friction bit-joined specimens. Additionally, the thermal decomposition temperature of the as-received carbon fiber composite was studied by thermogravimetric analysis. Fourier-transform infrared–attenuated total reflectance spectroscopy and X-ray diffraction measurements showed minimal variations in the absorption peak and diffraction peak patterns, indicating insignificant thermal degradation of the carbon fiber matrix due to friction bit joining.

36 MATERIALS SCIENCE↗

Impact of Hydrogen Combustion on the Oxidation-induced Degradation of Heavy-duty Diesel Engine Piston Materials

High temperature ferritic-martensitic steels are candidate materials for heavy-duty diesel engine pistons. The envisioned transition to hydrogen blended fuels is expected to alter the post-combustion atmosphere in the engines, primarily resulting in a higher water vapor content (> 20 vol%) and potentially higher exhaust gas temperatures. The oxidation resistance of existing and newly developed alloys will be a critical life-limiting mechanism under these conditions. In the present work, the oxidation behavior of candidate piston alloys was evaluated in air+10 vol.% H2O and air+30 vol.% H2O at 700°C. Thermal cyclic (1h cycle) exposures were conducted for two variants of commercial UNSS42200 ferritic-martensitic steel and two developmental alloy steels for up to 300h. The developmental alloys each have similar compositions but with one containing elevated Cu levels of 3 wt.%, A significant reduction in resistance to breakaway oxidation was observed for the commercial alloys in the higher water vapor atmosphere. Microstructural characterization (optical metallography, scanning electron microscopy and electron microprobe analysis) revealed the formation of thick Fe-rich oxides even for the high Cr (~12 wt.%) steels after an initial stage of protective oxidation with MnCr-rich spinels. The impact of the evaporation-induced loss of Cr on the time and temperature dependent compositional changes in the alloys was correlated with experimental findings. For the developmental alloys, Cu additions appear to play a role in significantly reducing oxidation kinetics in air+30 vol.% H2O at 700°C.

Pillai, Rishi [ORNL] (ORCID:0000000243688197)↗

The role of nickel content and the magnetic remanence in iron-nickel alloys of lunar composition

Lunar samples are magnetic primarily due to the body centered cubic (BCC) iron and iron-nickel alloys they contain. Presented for the first time are results which demonstrate that the magnitude of the martensitic thermal remanence (MTRM) induced on quenching iron-nickel alloy in the geomagnetic field depends on the nickel content of the alloy. High magnetic stability is due to the increasing dislocation density and increasingly complex microstructures associated with increasing nickel content in the alloys. The results agree with the mechanical and structural properties of the alloys. The characteristic quench martensite microstructure observed on metallographic examination provides a recognition criterion for the MTRM mechanism. These results are important for lunar and meteoritic research intending to ascertain the paleofield responsible for the observed remanent magnetization.-

Wasilewski, P.↗

Phase transformation and stabilization of a high strength austenite

An investigation of the phase transformation and the austenite stabilization in a high strength austenite has been made. An Fe-29Ni-4.3Ti austenite age-hardened by gamma-prime (Ni3Ti) precipitates showed a further increase of strength after martensitic and reverse martensitic phase transformations. The stability of ausaged austenite as well as ausaged and transformation-strengthened austenite was improved significantly through an isothermal treatment at 500 C. The Ms temperature of the strengthened austenite was restored to nearly that of annealed austenite while the austenite was hardened to R(C) 41 through precipitation and phase transformations. The observed austenite stabilization is attributed to the formation of GP zones or short-range order of less than about 10A in size.

Jin, S.↗

Fractographic analysis of gaseous hydrogen induced cracking in 18Ni maraging steel

Electron microscope fractographic analysis supplemented an extensive study of the kinetics of gaseous hydrogen assisted cracking in 18Ni maraging steel. Temperature determined the crack path morphology in each steel which, in turn, was directly related to the temperature dependence of the crack growth rate. Crack growth in the low temperature regime proceeded along prior austenite grain boundaries. Increasing the temperature above a critical value produced a continuously increasing proportion of transgranular quasi-cleavage associated with lath martensite boundaries. The amount of transgranular cracking was qualitatively correlated with the degree of temperature-induced deviation from Arrhenius behavior. Fractographic observations are interpreted in terms of hypothesized mechanisms for gaseous hydrogen embrittlement. It is concluded that hydrogen segregation to prior austenite and lath martensite boundaries must be considered as a significant factor in developing mechanisms for gaseous embrittlement of high strength steels.

Gangloff, R. P.↗