Results for “Langley analysis” — Page 49

NASA NTRS1995

Analysis of uncertainty in force balance calibration

In order to reduce errors encountered in the measurement and identification of loads using force balances, a third-order forward polynomial relation between loads and output voltages is proposed. This full third-order model represents an alternative to the second-order model currently in use at NASA Langley Research Center (LaRC) and many other installations worldwide. The new model requires the identification of 84 coefficients (including the 28 used presently) for each of the six outputs. The existing LaRC calibration loading sequence is insufficient for identification of many of these 504 coefficients because critical three-load combinations are absent. Accordingly, a new loading sequence that permits the identification of all 504 coefficients has been developed and is described fully. It is apparent from numerical tests that the new third-order model is clearly superior to second-order models in the presence of small amounts of random measurement noise, assuming that there are indeed higher-order interactions between loads. As the amount of noise increases, however, a third-order model becomes less attractive due to its ability to match the noise itself more faithfully than a second-order model. Numerical results suggest that the transition occurs when the magnitude of random noise becomes of the same order as that of the physical higher-order interactions.

Bursal, Faruk H.↗

NASA NTRS1985

Power spectral density of subsonic jet noise

The power-spectrum density (PSD) of the far-field noise of a subsonic unheated axisymmetric jet is investigated by analysis of about 80 sets of published noise spectra and of spectra obtained using 12.7 and 25.4-mm-diameter compressed-air jets at exit velocities 66 and 104 m/s and 67 and 91 m/s, respectively, in the NASA Langley anechoic flow facility. The results are presented in tables and graphs and characterized in detail. Findings reported include Strouhal-number scaling of the PSD at theta = 30 deg or more, scaling with the product of the Helmholtz number and the Doppler factor at theta less than 30 deg, best collapse at source convection Mach number 0.5, variation of PSD amplitude as U to the 6.5th at theta = 90 deg, and no sharp PSD-amplitude variation at any critical Reynolds number.

Zaman, K. B. M. Q.↗

NASA NTRS2011

Flight Simulation of ARES in the Mars Environment

A report discusses using the Aerial Regional- scale Environmental Survey (ARES) light airplane as an observation platform on Mars in order to gather data. It would have to survive insertion into the atmosphere, fly long enough to meet science objectives, and provide a stable platform. The feasibility of such a platform was tested using the Langley Standard Real- Time Simulation in C++. The unique features of LaSRS++ are: full, six-degrees- of-freedom flight simulation that can be used to evaluate the performance of the aircraft in the Martian environment; capability of flight analysis from start to finish; support of Monte Carlo analysis of aircraft performance; and accepting initial conditions from POST results for the entry and deployment of the entry body. Starting with a general aviation model, the design was tweaked to maintain a stable aircraft under expected Martian conditions. Outer mold lines were adjusted based on experience with the Martian atmosphere. Flight control was modified from a vertical acceleration control law to an angle-of-attack control law. Navigation was modified from a vertical acceleration control system to an alpha control system. In general, a pattern of starting with simple models with well-understood behaviors was selected and modified during testing.

Kenney, P. Sean↗

NASA NTRS2015

Analysis of Limit Cycle Oscillation Data from the Aeroelastic Test of the SUGAR Truss-Braced Wing Model

Research focus in recent years has been given to the design of aircraft that provide significant reductions in emissions, noise and fuel usage. Increases in fuel efficiency have also generally been attended by overall increased wing flexibility. The truss-braced wing (TBW) configuration has been forwarded as one that increases fuel efficiency. The Boeing company recently tested the Subsonic Ultra Green Aircraft Research (SUGAR) Truss-Braced Wing (TBW) wind-tunnel model in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT). This test resulted in a wealth of accelerometer data. Other publications have presented details of the construction of that model, the test itself, and a few of the results of the test. This paper aims to provide a much more detailed look at what the accelerometer data says about the onset of aeroelastic instability, usually known as flutter onset. Every flight vehicle has a location in the flight envelope of flutter onset, and the TBW vehicle is not different. For the TBW model test, the flutter onset generally occurred at the conditions that the Boeing company analysis said it should. What was not known until the test is that, over a large area of the Mach number dynamic pressure map, the model displayed wing/engine nacelle aeroelastic limit cycle oscillation (LCO). This paper dissects that LCO data in order to provide additional insights into the aeroelastic behavior of the model.

Bartels, Robert E.↗

NASA NTRS1975

Results of flow-visualization investigations on a 0.015-scale modified configuration 140A/B space shuttle vehicle orbiter (model 36-0) in the Langley Research Center 8-foot transonic pressure tunnel (OA102)

The results are presented of a flow-visualization wind tunnel test of a 0.015-scale model of the Modified Configuration 140A/B Space Shuttle Vehicle Orbiter. Separation zones, flow-recirculation regions, and potential venting and contaminant-ingestion problem areas were studied by means of photographic (video tape) analysis of model-mounted tufts. The model was tested at Mach numbers of 0.60, 0.90, 1.05, and 1.20, at Reynolds numbers of 3.17, 3.98, 4.16, and 4.23, respectively. Model angle-of-attack was varied from 0 deg to 20 deg at 0 deg sideslip-angle. Three control-surface deflection combinations were tested.

Nichols, M. E.↗

NASA NTRS1976

An analysis of data related to the minimum temperatures for valid testing in cryogenic wind tunnels using nitrogen as the test gas

The minimum operating temperature which avoids adverse low temperature effects, such as condensation, has been determined at a free stream Mach number of 0.85 for flow over a 0.137 meter airfoil mounted at zero incidence in the Langley 1/3 meter transonic cryogenic tunnel. The onset of low temperature effects is established by comparing the pressure coefficient measured at a given orifice for a particular temperature with those measured at temperatures sufficiently above where low temperature effects might be expected to occur. The pressure distributions over the airfoil are presented in tabular form. In addition, the comparisons of the pressure coefficient as a function of total temperature are presented graphically for chord locations of 0, 25, 50, and 75 percent. Over the 1.2 to 4.5 atmosphere total pressure range investigated, low temperature effects are not detected until total temperatures are 2 K, or more, below free stream saturation temperatures.

Hall, R. M.↗

NASA NTRS2024

Computational Analysis of the X-57 Maxwell Airplane, the Landing Configuration with High-Lift Blowing and Aileron Deflections (Preliminary Fuselage)

The X-57 Maxwell is an all-electric airplane with a distributed electric propulsion system used for a high-lift system at takeoff and landing conditions. The Kestrel and USM3D flow solvers were used at NASA Langley to investigate the performance of the X-57 Maxwell in the development of an aerodynamic database. The configuration investigated in this paper had a 30° flap deflection, and in addition the pilot’s right aileron were deflected and undeflected in different cases. The solutions were computed at an airspeed of 58 KEAS, for an altitude of 6000 feet, and a flight Reynolds number of 0.588e+06 per foot. To evaluate the high-lift distributed electric propulsion system without aileron deflections, the solutions were computed for an angle-of-attack sweep from −2° to 20°, with the high-lift propellers blowing and the cruise propellers excluded from the simulation. To investigate the aileron effectiveness, the solutions were computed at angles of attack of −2° and 14°, for aileron deflections from −25° to 18° with the high-lift propellers blowing and the cruise propellers windmilling at idle-power. The high-lift propellers and the idle-power cruise propellers were modeled with an actuator disk. Results show negligible differences in lift, drag and pitching moment whether the idle-powered cruise propellers were included or excluded from the simulation. In general, the Kestrel and USM3D codes compared well for lift, drag and pitching moment for the landing configuration with no aileron control. The Kestrel code, using the Spalart-Allmaras turbulence model with the rotation corrections terms, predicted an increasing lift coefficient up to maximum lift coefficient of 4.65 at a 15° angle of attack. The USM3D code, using the Spalart-Allmaras turbulence model turbulence model with the Quadratic Constitutive Relation predicted an increasing lift coefficient up to maximum lift coefficient of 4.5 at a 12° angle of attack, with the lift remaining constant through a 14◦ angle of attack. A possible difference in lift coefficient between the codes for high angles of attack may result from the different available options used with the standard Spalart-Allmaras turbulence model. The Kestrel code predicted more drag across the range of angle of attack than the USM3D code. The codes compared well for pitching moment coefficient across the range of angle of attack. The Kestrel and USM3D codes compared well for aileron effectiveness at a 2° angle of attack. The Kestrel code predicts better aileron effectiveness than USM3D at a 14° angle of attack. There is more flow separation in the region outboard of the last high-lift nacelle for the USM3D solutions at a 14° angle of attack, which diminishes the ability of the aileron to be effective.

X-57 Maxwell Airplane↗

NASA NTRS1991

Guidance and control analysis of the entry of a lifting body personnel launch vehicle

NASA is currently involved in definition studies of a Personnel Launch System (PLS) that could be used to transport people to and from low-earth orbit. This vehicle would serve both to complement the Space Shuttle and to provide alternative access to space in the event the Space Shuttle fleet were unavailable for a prolonged period. The PLS would consist of a manned spacecraft launched by an expendable vehicle, e.g., Titan 4. One promising candidate for the manned component of the PLS is the NASA Langley Research Center HL-20 lifting body. Many studies are currently underway to assess this vehicle, and one of the main areas of study is the development of the capability to successfully enter, glide to the landing site, and land. To provide this capability, guidance and control algorithms have been developed, incorporated into a six-degree-of-freedom simulation, and evaluation in the presence of off-nominal atmospheric conditions, consisting of both density variations and steady-state winds. In addition, the impact of atmospheric turbulence was examined for the portion of flight from Mach 3.5 to touchdown. This analysis showed that the vehicle remained controllable and could successfully land even in the presence of off-nominal atmospheric conditions.

Powell, Richard W.↗

NASA NTRS2018

Vehicle Design Data Format and Process for a Complete TARIS and OLTARIS Radiation Analysis for Designers and Engineers

Protecting astronauts from space radiation is a complex task when it comes to modeling and simulation. This document shows what information is needed from a spacecraft designer using CAD (Computer-Assisted Design) at each phase of the design to enable the engineers to evaluate the design phase against space radiation limits to determine the suitability of the design for space flight. The current personal exposure limits are listed in NASA STD-3001. A proxy to determine the REID (Radiation Exposure Induced Death) in NASA STD-3001 is the whole body effective dose equivalent (E or effective dose). For short-term tissue effects, organ-averaged gray equivalent (G (sub T)) is used. The TARIS (Tool for the Assessment of Radiation In Space - for LaRC (Langley Research Center) engineers) and OLTARIS (On-Line TARIS) - for designers) systems are used to generate these response functions. The E can use ICRP60 or NASA Q-values. A possible space radiation design basis environment for short-term tissue effects is described and used in all analyses. A single space vehicle was designed with three astronaut configurations and two of those configurations were used in a storm shelter thickness perturbation analysis. Conversion of the data from the CAD model to input necessary for TARIS and OLTARIS is also discussed in detail with relevant examples.

Singleterry, Robert C.↗

NASA NTRS1975

Free-flight model investigation of a vertical-attitude VTOL fighter

Tests were made in the Langley full-scale tunnel and included a study of the stability and control characteristics of delta- and swept-wing configurations from hovering through the transition to normal forward flight. Static force tests were also conducted to aid in the analysis of the flight tests. With conventional artificial rate stabilization, very smooth transitions could be made consistently with relatively little difficulty. Because of the lower apparent damping and a tendency to diverge in yaw, however, the swept-wing configuration was considered to be much more difficult to fly than the delta-wing configuration. With rate dampers off, both configurations were very difficult to control and the control power needed for satisfactory flights was substantially higher than with the rate dampers operating.

Newsom, W. A., Jr.↗

NASA NTRS1977

Pressure distributions on a 1- by 3-meter semispan wing with a nonstreamwise tip in subsonic flow

Pressure distributions on a 1- by 3-meter semispan wing with a tip that is streamwise at 0 deg sweep are presented. The tip becomes nonstreamwise as the wing is swept. At 0 deg sweep angle, the semispan wing has a taper ratio of 1.0 and NACA 0012 airfoil section contours. The test was conducted in the Langley V/STOL tunnel at a freestream dynamic pressure of 2.46 kPa. Pressure distributions are presented for sweep angles of 10, 20, 30, and 40 with an angle of attack range from -6 deg to 20 deg. The data are presented without analysis or discussion.

Yip, L. P.↗

NASA NTRS1990

Aircraft en route noise annoyance

Results are reported from a laboratory experiment conducted in order to quantify the annoyance experienced by people on the ground in response to en route noise (ERN) generated by aircraft at cruise conditions. Objectives included the comparison of annoyance responses to ERN with the annoyance responses to takeoff and landing noise; the comparison of the annoyance responses to advanced turboprop aircraft ERN with those of the turbofan ERN; and also the ability of aircraft noise measurement procedures and corrections to predict annoyance to ERN. Tests were conducted at the Langley Acoustics Research Laboratory on 32 human subjects selected at random. Subjects judged the annoyance level of 24 Propfan Test Assessment advanced turboprop ERN stimuli, 18 conventional turbofan ERN stimuli, and 60 conventional turboprop and turbofan takeoff and landing noise stimuli. Analysis of resulting data compared annoyance responses to different aircraft types and operations, examined the ability of current noise measurement and correction procedures to predict annoyance ERN, and calculated optimum duration correction magnitudes for ERN.

Mccurdy, David A.↗

NASA NTRS2000

Simultaneous Global Pressure and Temperature Measurement Technique for Hypersonic Wind Tunnels

High-temperature luminescent coatings are being developed and applied for simultaneous pressure and temperature mapping in conventional-type hypersonic wind tunnels, providing global pressure as well as Global aeroheating measurements. Together, with advanced model fabrication and analysis methods, these techniques will provide a more rapid and complete experimental aerodynamic and aerothermodynamic database for future aerospace vehicles. The current status in development of simultaneous pressure- and temperature-sensitive coatings and measurement techniques for hypersonic wind tunnels at Langley Research Center is described. and initial results from a feasibility study in the Langley 31-Inch Mach 10 Tunnel are presented.

Buck, Gregory M.↗

NASA NTRS1947

Investigation of an Experimental Supersonic Axial-Flow Compressor

An investigation is in progress at the Langley Laboratory of the NACA to explore the possibilities of axial-flow compressors operating with supersonic velocities relative to the blade rows. The first phase of this investigation, a study of supersonic diffusers, has been reported. The second phase, an analysis of supersonic compressors, has also been reported. Preliminary calculations have shown that very high pressure ratios across a stage, together with somewhat increased mass flows, are possible with compressors which decelerate air through the speed of sound in their rotor blading. These performance characteristics are desirable in compressors for aircraft jet propulsion units, gas turbines, or superchargers. The third phase, presented here, is a preliminary experimental investigation of a supersonic compressor designed to produce a high pressure ratio in a single stage.

Erwin, John R.↗

NASA NTRS2007

Virtual Diagnostics Interface: Real Time Comparison of Experimental Data and CFD Predictions for a NASA Ares I-Like Vehicle

Virtual Diagnostics Interface technology, or ViDI, is a suite of techniques utilizing image processing, data handling and three-dimensional computer graphics. These techniques aid in the design, implementation, and analysis of complex aerospace experiments. LiveView3D is a software application component of ViDI used to display experimental wind tunnel data in real-time within an interactive, three-dimensional virtual environment. The LiveView3D software application was under development at NASA Langley Research Center (LaRC) for nearly three years. LiveView3D recently was upgraded to perform real-time (as well as post-test) comparisons of experimental data with pre-computed Computational Fluid Dynamics (CFD) predictions. This capability was utilized to compare experimental measurements with CFD predictions of the surface pressure distribution of the NASA Ares I Crew Launch Vehicle (CLV) - like vehicle when tested in the NASA LaRC Unitary Plan Wind Tunnel (UPWT) in December 2006 - January 2007 timeframe. The wind tunnel tests were conducted to develop a database of experimentally-measured aerodynamic performance of the CLV-like configuration for validation of CFD predictive codes.

Schwartz, Richard J.↗

NASA NTRS2007

Virtual Diagnostics Interface: Real Time Comparison of Experimental Data and CFD Predictions for a NASA Ares I-Like Vehicle

Virtual Diagnostics Interface technology, or ViDI, is a suite of techniques utilizing image processing, data handling and three-dimensional computer graphics. These techniques aid in the design, implementation, and analysis of complex aerospace experiments. LiveView3D is a software application component of ViDI used to display experimental wind tunnel data in real-time within an interactive, three-dimensional virtual environment. The LiveView3D software application was under development at NASA Langley Research Center (LaRC) for nearly three years. LiveView3D recently was upgraded to perform real-time (as well as post-test) comparisons of experimental data with pre-computed Computational Fluid Dynamics (CFD) predictions. This capability was utilized to compare experimental measurements with CFD predictions of the surface pressure distribution of the NASA Ares I Crew Launch Vehicle (CLV) - like vehicle when tested in the NASA LaRC Unitary Plan Wind Tunnel (UPWT) in December 2006 - January 2007 timeframe. The wind tunnel tests were conducted to develop a database of experimentally-measured aerodynamic performance of the CLV-like configuration for validation of CFD predictive codes.

Schwartz, Richard J.↗

NASA NTRSDate not supplied

Overview and Performance of the LOFTID Instrumentation Suite

NASA’s Hypersonic Inflatable Aerodynamic Decelerator (HIAD) is an enabling technology that facilitates atmospheric entry of heavy payloads to planets such as Earth and Mars using a deployable aeroshell. The deployable nature of the HIAD technology allows it to overcome the size constraints imposed on current rigid aeroshell entry systems. This enables use of larger aeroshells resulting in increased entry system performance (e.g. higher payload mass and/or volume, higher landing altitude at Mars). On November 10th, 2022 the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was launched out of Vandenberg Air Force Base as a secondary payload on an Atlas V rocket. After the primary payload was delivered to its orbit, the LOFTID reentry vehicle was inflated, positioned, and then separated to reenter Earth’s atmosphere at a velocity of 8.1km/s, ultimately splashing down safely in the Pacific Ocean. The flight successfully demonstrated a 6m diameter, 70-deg sphere-cone HIAD on a high-energy orbital reentry. This demonstration has provided invaluable fight data essential to characterize the vehicle performance and support the ongoing effort to further scale the HIAD technology to vehicles of 10m in diameter or greater. Aeroshells of this scale are applicable to near-term commercial applications and future NASA robotic and human exploration missions. LOFTID incorporated an extensive instrumentation suite totaling over 150 science measurements. This included thermocouples, total heat flux sensors, and a radiometer to characterize the aeroheating environment and aeroshell thermal response. An Inertial Measurement Unit (IMU), Global Positioning System (GPS), and flush air data system was included to allow post-flight reconstruction of the vehicle trajectory including a decoupling of the aerodynamics from the atmospheric density. Loadcells were used to measure HIAD structural response during entry, and cameras (both visual-spectrum and infrared) were mounted on the aft segment looking at the aeroshell to monitor structural deflection and surface temperature distribution. Finally, a single up-look camera was included which has provided a surprising amount of science potential from the spectacular footage. In addition to the primary instrumentation suite, a new Fiber Optic Sensing System (FOSS) was used to provide global temperature distributions as a technology demonstration. The system provided over 200 thermal measurements creating a thermal map for the backside of the nose Flexible Thermal Protection System. Another pair of FOSS cables were run along the rigid center structure and measured the temperature response to the vehicle wake environment. The LOFTID instrumentation suite leveraged Agency-wide expertise, with hardware development occurring at Ames Research Center, Langley Research Center, Marshall Space Flight Center, and Armstrong Flight Research Center. This paper will discuss the instrumentation selected for LOFTID, a summary of sensor in-flight performance, and will provide examples of data products from the post-flight analysis effort.

Gregory T Swanson↗

NASA NTRSDate not supplied

Overview and Performance of the LOFTID Instrumentation Suite

NASA’s Hypersonic Inflatable Aerodynamic Decelerator (HIAD) is an enabling technology that facilitates atmospheric entry of heavy payloads to planets such as Earth and Mars using a deployable aeroshell. The deployable nature of the HIAD technology allows it to overcome the size constraints imposed on current rigid aeroshell entry systems. This enables use of larger aeroshells resulting in increased entry system performance (e.g. higher payload mass and/or volume, higher landing altitude at Mars). On November 10th, 2022 the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was launched out of Vandenberg Air Force Base as a secondary payload on an Atlas V rocket. After the primary payload was delivered to its orbit, the LOFTID reentry vehicle was inflated, positioned, and then separated to reenter Earth’s atmosphere at a velocity of 8.1km/s, ultimately splashing down safely in the Pacific Ocean. The flight successfully demonstrated a 6m diameter, 70-deg sphere-cone HIAD on a high-energy orbital reentry. This demonstration has provided invaluable fight data essential to characterize the vehicle performance and support the ongoing effort to further scale the HIAD technology to vehicles of 10m in diameter or greater. Aeroshells of this scale are applicable to near-term commercial applications and future NASA robotic and human exploration missions. LOFTID incorporated an extensive instrumentation suite totaling over 150 science measurements. This included thermocouples, total heat flux sensors, and a radiometer to characterize the aeroheating environment and aeroshell thermal response. An Inertial Measurement Unit (IMU), Global Positioning System (GPS), and flush air data system was included to allow post-flight reconstruction of the vehicle trajectory including a decoupling of the aerodynamics from the atmospheric density. Loadcells were used to measure HIAD structural response during entry, and cameras (both visual-spectrum and infrared) were mounted on the aft segment looking at the aeroshell to monitor structural deflection and surface temperature distribution. Finally, a single up-look camera was included which has provided a surprising amount of science potential from the spectacular footage. In addition to the primary instrumentation suite, a new Fiber Optic Sensing System (FOSS) was used to provide global temperature distributions as a technology demonstration. The system provided over 200 thermal measurements creating a thermal map for the backside of the nose Flexible Thermal Protection System. Another pair of FOSS cables were run along the rigid center structure and measured the temperature response to the vehicle wake environment. The LOFTID instrumentation suite leveraged Agency-wide expertise, with hardware development occurring at Ames Research Center, Langley Research Center, Marshall Space Flight Center, and Armstrong Flight Research Center. This paper will discuss the instrumentation selected for LOFTID, a summary of sensor in-flight performance, and will provide examples of data products from the post-flight analysis effort.

Greg Swanson↗